Description
SS-RSRPB (Synchronization Signal Reference Signal Received Power per branch) is a physical layer measurement defined for 5G NR. It represents the received power of the Synchronization Signal (SS) reference signals, measured separately for each receive branch (antenna) at the UE. The Synchronization Signal block (SSB) consists of the Primary Synchronization Signal (PSS), Secondary Synchronization Signal (SSS), and Physical Broadcast Channel (PBCH) demodulation reference signals. SS-RSRPB is derived from these signals and provides a per-branch power measurement that complements the aggregated SS-RSRP measurement.
The measurement is specified in 3GPP technical reports 38.810 and 38.884, which cover NR physical layer measurements and their accuracy requirements. SS-RSRPB is measured over the synchronization signal resources and is used by the UE to evaluate the quality of each receive branch independently. This is particularly relevant for devices with multiple receive antennas, where branch imbalance or blockage can affect overall performance. By measuring power per branch, the UE and network can detect antenna-specific issues and optimize receive diversity and beamforming strategies.
In terms of how it works, the UE measures the received power of the SSS (and optionally the PBCH DMRS) within the SSB bandwidth for each receive branch. The measurement is filtered over time to reduce the impact of noise and fading, following the same filtering framework as other NR measurements. The resulting per-branch values can be reported to the network or used internally by the UE for radio link monitoring, beam failure detection, and receive beam selection. The network may use these measurements to configure MIMO operation, adjust transmit power, or trigger handover decisions.
SS-RSRPB is closely related to SS-RSRP, which is the aggregated received power across all receive branches. While SS-RSRP provides a single value representing overall signal strength, SS-RSRPB provides granular information about each branch. This granularity is valuable in mmWave deployments where beamforming and spatial multiplexing are essential, and where individual antenna elements may experience different channel conditions. The per-branch measurement also supports advanced receiver algorithms that combine signals from multiple branches to improve SNR and throughput.
The measurement is applicable in both idle and connected modes, although reporting is typically configured in connected mode. In idle mode, the UE may use SS-RSRPB internally for cell selection and reselection evaluations. The accuracy requirements for SS-RSRPB are defined in 38.884, which specifies tolerances under various channel conditions, including AWGN, fading, and interference. These requirements ensure that the measurement is reliable enough for network optimization and mobility decisions.
In the context of 5G NR, SS-RSRPB supports key procedures such as beam management, where the UE measures multiple beams and reports the best beam per branch. It also aids in radio link monitoring, where per-branch measurements can detect degradation in specific receive paths before overall link failure occurs. As networks evolve toward higher frequencies and more advanced antenna systems, per-branch measurements like SS-RSRPB become increasingly important for maintaining robust connectivity.
Purpose & Motivation
SS-RSRPB was introduced to provide per-receive-branch power measurements in 5G NR, addressing the limitations of aggregated measurements like SS-RSRP. In earlier LTE systems, RSRP was measured per antenna port but not per receive branch, which limited the ability to diagnose branch-specific issues. With the introduction of massive MIMO and mmWave in NR, the need for granular per-branch measurements became critical for beam management and receive diversity optimization.
The measurement exists to support advanced receiver algorithms and network optimization. By knowing the power received on each branch, the UE can detect antenna blockage, imbalance, or failure, and the network can adjust MIMO configurations accordingly. This is particularly important in high-frequency deployments where signal propagation is more directional and susceptible to obstruction.
SS-RSRPB also supports radio link monitoring and beam failure detection. Per-branch measurements allow the UE to identify which receive beams are degraded and to trigger recovery procedures more precisely. This improves the reliability of connections in challenging radio environments, such as those encountered in mmWave and mobility scenarios.
Release Timeline
Evolution Across Releases
An overview written from the defining specifications, not a verified change history. For the exact text, open the specifications listed below.
Defining Specifications
3GPP specifications that define or reference SS-RSRPB, with the latest known release. Sourced from the 3GPP document catalog — see methodology.
| Specification | Title | Release |
|---|---|---|
| TR 38.810 vg70 | NR OTA Test Methods Study | Rel-16 read |
| TR 38.884 vi20 | Technical Report | Rel-18 read |