Description
A Secondary Cell (SCell) is a fundamental building block of Carrier Aggregation (CA) in both LTE (TS 36.331) and NR (TS 38.331). In CA, a UE is configured with a set of serving cells consisting of exactly one Primary Cell (PCell) — the cell on which the UE performs initial connection establishment and RRC connection re-establishment — plus zero or more SCells. The SCell operates on a secondary frequency (a Secondary Component Carrier, SCC) and is configured by RRC once an RRC connection is established. Unlike the PCell, an SCell cannot serve as the anchor for initial access, security, or NAS mobility; it is purely an additional radio resource.
SCells are configured and managed through dedicated RRC signalling. The network adds an SCell using the SCellToAddModList IE, which specifies the SCell index, the ARFCN of the secondary frequency, the physical cell identity, and the common and dedicated radio resource configuration. Activation and deactivation of SCells is handled by MAC Control Elements (TS 36.321 / TS 38.321), allowing fast on/off control of the SCell without RRC reconfiguration — a key mechanism for energy efficiency and for avoiding unnecessary UE power consumption and interference when traffic demand is low. The sCellDeactivationTimer in the MAC layer automatically deactivates an SCell after a period of inactivity.
In the downlink, the UE monitors the PDCCH on the SCell (or via cross-carrier scheduling from the PCell) for scheduling assignments. In the uplink, the SCell may be configured with a PUCCH (in LTE, at most one SCell can carry PUCCH in addition to the PCell; in NR, PUCCH can be configured on SCells as well). Random access on an SCell is supported in NR (and in LTE for certain configurations) to enable uplink timing alignment per Timing Advance Group (TAG). SCells are grouped into TAGs, each with its own timing advance, reflecting the fact that different carriers may be served by different transmission points or experience different propagation delays.
In dual connectivity (EN-DC, NGEN-DC, NE-DC, NR-DC), the concept extends: the Master Node provides the PCell, and the Secondary Node provides the PSCell (Primary SCell). The PSCell is the special cell of the secondary cell group (SCG) on which the UE performs random access and monitors the PDCCH for the SCG. The Rel-15 definition clarifies that, except for (NG)EN-DC, the PSCell is considered to be an SCell — an important clarification for measurement and mobility procedures in TS 36.133 and TS 38.133, which define SCell measurement requirements (e.g., SCell activation delay, measurement reporting for SCell addition).
SCells play a central role in mobility and radio resource management. The network configures measurement objects and reporting events (e.g., A4, A6 in LTE; A4, A6 in NR) to decide when to add, modify, or release SCells based on radio conditions. SCell addition is typically triggered when the UE reports strong signal quality on a candidate secondary frequency, and SCell release when the quality degrades. Because SCells do not carry RRC or NAS signalling, their addition and release is a lightweight, fast procedure compared to handover, making CA a highly dynamic capacity tool. The SCell concept is also reused in NR-U, sidelink, and multi-TRP scenarios, where additional carriers or cells provide supplementary resources.
Purpose & Motivation
The Secondary Cell concept was introduced in LTE Rel-10 to realize Carrier Aggregation, which was 3GPP's answer to the growing demand for higher peak data rates beyond what a single 20 MHz LTE carrier could deliver. Before CA, a UE could only be served by one cell at a time; achieving higher throughput required wider single carriers, which were impractical given fragmented spectrum allocations and backward-compatibility constraints. By allowing the network to aggregate multiple component carriers — each up to 20 MHz in LTE — CA enabled peak rates of 100 Mbps and beyond (and much higher with later enhancements) while preserving compatibility with Rel-8 UEs.
The SCell abstraction solves several problems. First, it decouples capacity expansion from the anchor cell: the PCell remains responsible for connection control, security, and mobility, while SCells add pure capacity. Second, it enables dynamic, low-overhead activation and deactivation via MAC, so the network can exploit additional spectrum only when needed, saving UE battery and reducing interference. Third, it supports heterogeneous deployments where SCells may be small cells on different frequencies, enabling load balancing and coverage extension.
In NR, the SCell concept was carried forward and extended (e.g., PUCCH on SCells, SCell dormancy, and multiple SCells in FR1/FR2), reflecting its enduring value as the fundamental mechanism for multi-carrier operation across generations.
What changed in its specifications
The latest release-to-release comparison of specifications that define Secondary Cell. Each summary describes the whole specification, not only this term.
Rel-19 adds enhanced NR NTN and IoT NTN requirements and test methods to TS 36.133. It also removes many clauses, mainly SCell delay, RSRP accuracy, NB-IoT and LTE-M measurement and test sections, plus multi-layer gap monitoring and CGI identification clauses.
Full comparison in TS 36.133 →Rel-19 adds NTN-for-IoT Phase 3 and inter-RAT mobility from E-UTRAN to NR NTN, plus LTE-based 5G Broadcast Phase 2 changes. It also adds IMS disaster-roaming access barring, NTN-for-NR Phase 3 fields, and NR RRM Phase 5 items.
Full comparison in TS 36.331 →Release Timeline
Detected Changes Across Releases
from 3GPP Change RequestsSpecific changes extracted from the „Change history“ tables of 3GPP specifications (1 CRs across 1 releases). Complements the general historical overview above with the evidence-based evolution of this function.
Defining Specifications
3GPP specifications that define or reference Secondary Cell, with the latest known release. Sourced from the 3GPP document catalog — see methodology.
| Specification | Title | Release |
|---|---|---|
| TS 36.133 vj60 | LTE Radio Resource Management Requirements | Rel-19 read |
| TS 36.331 vj40 | E-UTRA Radio Resource Control (RRC) Protocol | Rel-19 read |
| TS 36.521 vj11 | E-UTRA UE Conformance Testing for Satellite Access | Rel-19 read |
| TS 36.855 vd00 | LTE Positioning Enhancements Study | Rel-13 read |
| TS 38.133 vk10 | NR Radio Resource Management Requirements | Rel-20 read |
| TS 38.331 vj40 | NR Radio Resource Control (RRC) | Rel-19 read |
| TS 38.533 vj40 | NR UE RRM Conformance Testing | Rel-19 read |