Menu
Latest
12 meetings · Prague, Jeju · 12–16 Oct
Reports
RAN1#126-bis · SA2#177

Glossary term · Radio Access Network

SAN RF Bandwidth

SAN (Satellite Access Node) Radio Frequency Bandwidth

Radio Access Network →

SAN RF Bandwidth is the RF bandwidth in which a Satellite Access Node transmits and/or receives single or multiple carriers within a supported operating band, bounding the total spectrum it can use across all carriers.

Introduced
Rel-17
Where
Radio Access Network › NG-RAN (5G)
Specifications
4 specs
SAN RF Bandwidth Description Purpose Neighbours Specifications

Description

SAN RF Bandwidth is the radio-frequency bandwidth within which a Satellite Access Node transmits and/or receives one or multiple carriers inside a supported operating band. It is defined in the 3GPP RF specifications 36.108, 36.181, 38.108, and 38.181, and it represents the outermost spectral envelope of the SAN's radio interface. Whereas the SAN channel bandwidth describes the spectrum of a single carrier, the SAN RF bandwidth describes the aggregate spectrum the node occupies when it operates one or several carriers — contiguous or non-contiguous — within an operating band.

The hierarchy of RF parameters is important: the operating band is the regulatory/3GPP-defined block of spectrum (e.g., n256, n255 for satellite bands); the SAN RF bandwidth is the portion of that band the node actually uses; within it, one or more SAN channel bandwidths are placed, each containing a transmission bandwidth configuration of resource blocks. The SAN RF bandwidth therefore acts as the container for multi-carrier operation. If a SAN supports carrier aggregation or multi-carrier transmission, all constituent carriers must fall within the SAN RF bandwidth, and the RF requirements (such as out-of-band emissions and spurious limits) are evaluated at the edges of this aggregate bandwidth.

In practice, the SAN RF bandwidth is a key parameter in link budget and capacity planning. A wider SAN RF bandwidth allows the node to host more carriers, serve more simultaneous users, and offer higher peak throughput, but it also increases the power spectral density challenge: the same transmit power spread over a wider bandwidth reduces power per Hz, shrinking the coverage footprint. Satellite operators therefore choose the SAN RF bandwidth to balance capacity against coverage, often using narrower bandwidths for broad beams and wider bandwidths for high-capacity spot beams.

The parameter also governs RF conformance testing. Test cases in 36.108/38.108 (conducted) and 36.181/38.181 (radiated, for satellite) verify transmitter characteristics — maximum output power, EVM, frequency error, unwanted emissions — and receiver characteristics — reference sensitivity, blocking, adjacent channel selectivity — across the declared SAN RF bandwidth. Because satellite access nodes are tested over the air (radiated) rather than only conducted, the SAN RF bandwidth definition is essential for setting up anechoic-chamber or compact-antenna-test-range measurements with correct spectral reference planes.

For network architects, SAN RF Bandwidth is the top-level spectrum resource of the satellite node. It determines how many carriers can be deployed, how guard bands are allocated between carriers and at band edges, and how the node coexists with adjacent satellite or terrestrial systems. It is the natural companion to the SAN channel bandwidth and the SAN transmission bandwidth configuration, and together these three parameters fully describe the spectral usage of a Satellite Access Node in 3GPP NTN deployments.

Purpose & Motivation

The introduction of Non-Terrestrial Networks in Release 17 required 3GPP to define RF parameters for a new class of access node — the Satellite Access Node — that operates multiple carriers over a wide spectrum allocation, often in Ka/Ku-band or S-band satellite spectrum. Terrestrial base-station specifications defined RF bandwidth primarily for a single carrier or for carrier-aggregation scenarios at ground level; they did not provide a clean aggregate-spectrum reference for a satellite node that may transmit several carriers within a shared, regulatorily constrained band. The SAN RF Bandwidth term fills that gap by defining the total RF envelope in which the SAN transmits and/or receives single or multiple carriers within a supported operating band.

This definition solves several problems. First, it gives RF conformance testing a well-defined aggregate reference so that unwanted-emission and blocking requirements can be evaluated at the correct spectral edges when multiple carriers are active. Second, it supports coexistence analysis: satellite bands are shared with other services, and regulators need to know the maximum spectral footprint a SAN will occupy. Third, it enables flexible multi-carrier deployment planning, letting operators place carriers within a declared RF bandwidth rather than being locked to a single-carrier model.

By separating the aggregate SAN RF bandwidth from the per-carrier SAN channel bandwidth, 3GPP gives vendors and operators a modular framework: a node declares its RF bandwidth capability, and carriers are then configured within it according to capacity and coverage needs. This mirrors, and extends to space, the terrestrial paradigm of operating band versus carrier bandwidth.

Release Timeline

Evolution Across Releases

An overview written from the defining specifications, not a verified change history. For the exact text, open the specifications listed below.

Rel-17 Initial

Initial definition introduced with NTN support: the SAN RF bandwidth was defined as the RF bandwidth in which a SAN transmits and/or receives single or multiple carriers within a supported operating band, establishing the aggregate spectral reference for satellite access nodes.

The definition carried over unchanged from Rel-17, retaining the single-or-multiple-carrier wording within a supported operating band.

The definition remained unchanged from Rel-18; no textual revision to the SAN RF bandwidth definition is reflected in the quoted wording.

The definition remained unchanged from Rel-19, continuing to describe the RF bandwidth for single or multiple carriers within a supported operating band.

Defining Specifications

3GPP specifications that define or reference SAN RF Bandwidth, with the latest known release. Sourced from the 3GPP document catalog — see methodology.

SpecificationTitleRelease
TS 36.108 vk00 Satellite Access Node RF Requirements Rel-20 read
TS 36.181 vj40 RF Test Methods and Conformance for Satellite Access Nodes Rel-19 read
TS 38.108 vk00 NR NTN Satellite Access Node RF Requirements Rel-20 read
TS 38.181 vj40 NR Satellite Access Node RF Conformance Testing Rel-19 read