Menu

GSMA · Specification

SGP.02v4.1

UICC Technical Specification

Specifies the architecture, interfaces, security functions and procedures for remotely provisioning and managing embedded UICCs in hard-to-reach M2M devices.

Version
v4.1
  1. v4.32023-01-25
  2. v4.2.12021-11-26
  3. v4.22020-07-07
  4. v4.12020-06-05
  5. v4.02019-02-25
  6. v3.22017-06-27
  7. v3.12016-05-27
  8. v3.02015-09-30
  9. v2.12015-11-02
  10. v2.02014-10-13
  11. v1.02013-12-17
Issued
2020-06-05
Source
Original PDF

A formatted version of this document is not available yet; the text below is extracted clause by clause, so tables and figures may be incomplete.

Overview

This specification describes the remote provisioning architecture for embedded UICCs in machine-to-machine devices that are not easily reachable. It covers eUICC architecture and security, OTA and other interfaces among operators, service providers, SM-DP, SM-SR and eUICC platforms, and procedures for downloading, installing, enabling, disabling and deleting profiles. It also defines interface functions, message mappings, SOAP and WSDL bindings, data definitions and device requirements. These technical details support interoperability across different operator deployments, network equipment and eUICC platforms.

  • eUICC
  • Remote SIM Provisioning
  • OTA
  • ES interfaces
  • SOAP
  • WSDL

Overview generated automatically from the document's scope and outline. The document text is authoritative.

Changes since v4.0

120 clauses modified, 7 clauses added

Compared automatically clause by clause from the extracted text of both versions; differences only in layout, spacing or table cells are ignored. The documents are authoritative.

1.5 Definition of Termsmodified

…, and enables the secure changing of Profiles. An Operational Profile with a Profile Attribute allocated, indicating that this Profile is an Emergency Profile. … Emergency Profile An Emergency Profile complies with regulatory requirements Emergency Profile and only provides the capability to make Emergency Calls and receive calls from an Emergency centre (e.g. Public Safety Answering Point) This is an attribute al … . A function of the interface between a Device and an eUICC that provides the capability for a Device to locally disable the Local Disable Emergency Profile or … the Test Profile on the eUICC without involvement of an SM-SR and/or SM-DP. A function of the interface between a Device and an eUICC that provides the capability for a Device to locally enable the Local Enable Emergency Profile or the Test Profile on the eUICC without involvement of an SM- SRSM-SR and/or SM-DP. M2M Service Provider (M2M A Service Provider relying on an Operator providing the Profiles SP) on the eUICC. An entity providing access capabilit… …

1.7 Referencesmodified

…Identity Module [52] 3GPP TS 31.102 (USIM) application, Release 9 SIMalliance: eUICC Profile Package - Interoperable Format [53] SIMAPP Technical Specification … V2.2,v2.3.1, 1028 SeptemberNovember 2018,2019, http://simalliance.org/euicc/euicc-technical-releases/ GlobalPlatform Card Specification v.2.2 Amendment A: [54] GPC_SPE_007 Confidential Card Content Manageme … Manager - Standard v3 [63] SGP.05 SGP.05 - Embedded UICC Protection Profile v1.1 [64] SGP.16 M2M Compliance Process v1.0 Internationalized Resource Identifiers … (IRIs)(IRIs). . January [65] RFC 3987 2005. http://www.ietf.org/rfc/rfc3987.txt Java Card Classic Platform Specification [66] Java Card https://www.oracle.com/java/technologies/javacard-specs- downloads.html Security architecture and procedures for 5G system (Release [67] 3GPP TS 33.501 15) [68] 3GPP TS 31.130 (U)SIM API for Java™ Card (Release 15)

2.2.1.3 ISD-Pmodified

…n 3.1.1). At least one ISD-P with a Profile SHALL be installed and first personalized by the EUM during eUICC manufacturing to allow future eUICC connectivity. … The ISD-P SHALL be able to receive and process a Profile Package, wrapped in an SCP03t Secure Channel, as specified in section 4.1.3.3. The eUICC SHALL support the SIMalliance: eUICC Profile Package - Interoperable Format Technical Specification [53] with the major version being 2 and the version being at least 2.3.1. The eUICC MAY in addition support higher major versions. The EUM SHALL indicate in the EIS the versions supported by the eUICC, as specified in section 5.1.1.2.10. No component outside the ISD-P SHALL have visibility or access to any Profile component with the exception of the ISD-R, which SHALL have read access to POL1 an… …

2.2.7 Java Card™ Supportadded

The eUICC MAY support Java Card™. If Java Card™ is supported, the eUICC SHALL support at least version 3.0.4 of the Java Card Classic Platform Specification [66].

2.4.3 SMSmodified

…S (MT or MO) SHALL make use of a CC with a length of 64 bits using AES CMAC mode, ciphering using AES in CBC mode and counter value higher (SPI1=’16’). Minimum … keyke y lengths are defined in section 2.3.3.  Procedures for the PoR SHALL follow ETSI TS 102 225 [4] and 3GPP TS 31.115 [13] with the following precisions:Inprecisions: in the case that an incoming SMS for the ISD-R does not meet this security level, it must be rejected by the eUICC and no PoR SHALL be sent back  When the eUICC c … gth of 64 bits using AES CMAC mode , ciphering using AES in CBC mode and SHALL be sent using SMS- SUBMIT mode. Minimum key lengths are defined in section 2.3.3. … The SM-SR SHALL verify that the counter value of the PoR is the same as the counter value sent in the command packet. All these security requirements SHALL apply also for the SCP80 secured packets exchanged during a CAT_TP session.

2.4.4.1 PSK-TLSmodified

Cipher Suites The eUICC SHALL support the Transport Layer Security (TLS) protocol v1.2 [15] and SHALL advertise at least one of the following Pre-Shared Key Cipher suites as defined in RFC 5487 [17]:  TLS_PSK_WITH_AES_128_GCM_SHA256  TLS_PSK_WITH_AES_128_CBC_SHA256 The Pre-Shared Keys SHALL have an entropy of at least 128 bits. The eUICC ISD-R SHALL be configured with ‘i’ = ‘04’ to indicate only TLS 1.2 supported as defined in GlobalPlatform Amd B [8]. The SM-SR SHALL select a cipher suite of the same or higher security compared to the two listed above. PSK-ID Value for TLS Handshake The PSK-ID specified in this section defines a format suited for PSK random keys. However, a SM-SR MAY use a dedicated PSK-ID format in particular to be able to manage PSK derived from master key. In this case the derivation algorithm used SHALL be robust and follow the NIST recommendation SP800-56C [55], the derived Pre-Shared Keys SHALL have an entropy of at least 128 bits. As specified in RFC 4279 [16], the PSK Identity SHALL be first converted to a character string, and then sent encoded in octets using UTF-8 [18] by the eUICC. In the context of this specification, the PSK Identity before conversion is a sequence of Tag/Length/Value (TLV) objects in hexadecimal string representation. NOTE: As the PSK Identity is expected to be as short as possible, all lengths are coded in one byte. BER-TLV coding is unnecessary in this case. Length Description Value (bytes) Tag for identifying PSK-ID format 1 ‘80’ Length 1 ‘01’ Identification of the PSK-ID 1 Expected value is ‘02’ indicating a full qualified format. format for random PSK. Tag for indicator of EID 1 ‘81’ Length of EID 1 ‘10’ EID value 16 The EID value. The value SHALL be coded in hexadecimal string representation. Tag for security domain AID 1 ‘4F’ Length of security domain AID 1 ‘10’ Security domain AID value 16 The AID value of the ISD-R. The value SHALL be coded in hexadecimal string representation. Tag for key identifier 1 ‘82’ Length 1 ‘01’ Key identifier 1 The key identifier value. The value SHALL be coded in hexadecimal representation. Tag for Key version 1 ‘83’ Length 1 ‘01’ Key version 1 The key version value. The value SHALL be coded in hexadecimal representation. Key version number range reserved for SCP81 is '40' to '4F'. Table 4: PSK-ID Format Example of PSK-ID before conversion to an UTF-8 string: ‘8001028110010203040506070809010203040506074F10000102030405060708090A0B0C 0D0E0F820101830140’ Other restrictions on TLS session management In addition to restrictions to the TLS protocol specified in GP Amendment B [8], the ISD-R and SM-SR SHALL NOT support TLS Session resumption (RFC 4507 or RFC 5077) nor several parallel TLS sessions.

2.4.4.1.1 Cipher Suitesadded

The eUICC SHALL support the Transport Layer Security (TLS) protocol v1.2 [15] and SHALL support at least one of the following Pre-Shared Key Cipher suites as defined in RFC 5487 [17]:  TLS_PSK_WITH_AES_128_GCM_SHA256  TLS_PSK_WITH_AES_128_CBC_SHA256 The Pre-Shared Keys SHALL have an entropy of at least 128 bits. The eUICC ISD-R SHALL be configured with ‘i’ = ‘04’ to indicate only TLS 1.2 supported as defined in GlobalPlatform Amd B [8]. The SM-SR SHALL select a cipher suite of the same or higher security compared to the two listed above.

2.4.4.1.2 PSK-ID Value for TLS Handshakeadded

The PSK-ID specified in this section defines a format suited for PSK random keys. However, a SM-SR MAY use a dedicated PSK-ID format in particular to be able to manage PSK derived from master key. In this case the derivation algorithm used SHALL be robust and follow the NIST recommendation SP800-56C [55], the derived Pre-Shared Keys SHALL have an entropy of at least 128 bits. As specified in RFC 4279 [16], the PSK Identity SHALL be first converted to a character string, and then sent encoded in octets using UTF -8 [18] by the eUICC. In the context of this specification, the PSK Identity before conversion is a sequence of Tag/Length/Value (TLV) objects in hexadecimal string representation. NOTE: As the PSK Identity is expected to be as short as possible, all lengths are coded in one byte. BER-TLV coding is unnecessary in this case. Length Description Value (bytes) Tag for identifying PSK-ID format 1 ‘80’ Length 1 ‘01’ Identification of the PSK-ID 1 Expected value is ‘02’ indicating a full qualified format. format for random PSK. Tag for indicator of EID 1 ‘81’ Length of EID 1 ‘10’ EID value 16 The EID value. The value SHALL be coded in hexadecimal string representation. Tag for security domain AID 1 ‘4F’ Length of security domain AID 1 ‘10’ Security domain AID value 16 The AID value of the ISD-R. The value SHALL be coded in hexadecimal string representation. Tag for key identifier 1 ‘82’ Length 1 ‘01’ Key identifier 1 The key identifier value. The value SHALL be coded in hexadecimal representation. Tag for Key version 1 ‘83’ Length 1 ‘01’ Key version 1 The key version value. The value SHALL be coded in hexadecimal representation. Key version number range reserved for SCP81 is '40' to '4F'. Table 4: PSK-ID Format Example of PSK-ID before conversion to an UTF-8 string: ‘8001028110010203040506070809010203040506074F10000102030405060708090A0B0C 0D0E0F820101830140’

2.4.4.1.3 Other restrictions on TLS session managementadded

In addition to restrictions to the TLS protocol specified in GP Amendment B [8], the ISD-R and SM-SR SHALL NOT support TLS Session resumption (RFC 4507 or RFC 5077) nor several parallel TLS sessions.

3.1.1 ISD-P Creationmodified

…by a key establishment procedure and the full download of the Profile. NOTE: CAT_TP could be used as transport protocol and would have an equivalent procedure. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 160 hide footbox participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox OP->>DP: (1) downloadProfile(srid, eid, iccid, final state, profileType) DP->SR: (2) getEIS(eid) Rnote over SR #FFFFF (3) Retrieve EIS Endrnote SR-->DP: Failed DP-->>OP: SR-->DP: (4) Return EIS Rnote over DP #FFFFFF (5) Check eUICC eligibility Endrnote DP-->>OP: Failed DP->>SR: (6) createISDP(eid, iccid, mno -id,…) Rnote over SR #FFFFFF (7) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP: Hnote over SR, ISDR #C0C0C0 HTTPS session opening Endhnote SR->>ISDR: (9) note over SR, ISDR **HTTP/1.1 200 CRLF** Headers CRLF <Body with ES5.createISD-P function> End note ISDR->ISDP: (10) New . ISDR->>SR: (11) note over SR, ISDR **POST /<next-uri> HTTP/1.1 CRLF** Headers X-Admin-Script-Status: <script-status> CRLF CRLF <Body with ES5.createISD-P response> End note Rnote over SR #FFFFFF (12) EIS update Endrnote SR->>DP: (13) create ISDP function response @enduml Figure 11: ISD-P creation Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Procedure: (1 … ICC is unknown in its system. The error SHALL be finally returned to the Operator and the procedure SHALL end. (4) The SM-SR SHALL return the EIS of the eUICC. … a. In case the EIS indicates an ISD-P in state 'Created' with the 'smdp-id' associating it to the calling SM-DP, the SM-DP SHALL delete this Profile, whether it has the same or a different ICCID, as described in section 3.1.5 before attempting to install a new Profile. (5) The SM-DP SHALL check the eligibility of the eUICC against the characteristics of the Profile to be downloaded. Although the exact checks performed by the S … ALL return a response indicating a failure, and the procedure SHALL stop. Otherwise the SM-SR, SHALL create a new Profile entry for the EIS having a state “In- … Creation”Creation”. . The Profile with this state SHALL NOT appear in the EIS returned on ES3.GetEIS and ES4.GetEIS (8) If there is no existing HTTPS session with the eUICC, the SM-SR SHALL trigger the HTTPS session as defined in section 2.4.4.5. (9) The SM-SR SHALL return the HTTP POST response containing the “ES5.CreateISDP”“ ES5.CreateISDP” with its relevant input data. The X-Admin-Targeted-Application parameter SHALL be omitted as the command is targeting the ISD-R. (10) The ISD-R SHALL create th… …

3.1.2 Key Establishment with Scenario#3-Mutual Authenticationmodified

…ses Scenario#3 based on ECKA EG (ElGamal) scheme as defined in GlobalPlatform Card Specification Amendment E [11] complemented by an SM-DP authentication step. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 160 hide footbox participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF participant ECASD #FFFFFF endbox DP->>SR: (1) sendData(eid, sd-aid, ES8.EstablishISDPKeySet(CERT.DP.ECDSA)) Rnote over SR (2) Check initial conditions End rnote SR-->>DP: Failed DP-->>OP: Hnote over SR, ISDR #C0C0C0 (2a) Conditional: HTTPS Session opening Endhnote SR->>ISDR: (3) note over SR, ISDR **HTTP/1.1 200 CRLF** … CRLF <Body with ES8.EstablishISDPKeySet(CERT.DP.ECDSA)> End note ISDR->ISDP: (3a) CERT.DP.ECDSA rnote over ISDP (3b) Verifies that it is an SM-DP certificate End rnote ISDP->ECASD: (4) CERT.DP.ECDSA Rnote over ECASD 5) verifies CERT.DP.ECDSA using PK.CI.ECDSA. Continue if successful: - extracts PK.DP.ECDSA from CERT.DP.ECDSA. - generates RC End rnote ECASD-->ISDP:(6) RC or error ISDP-->ISDR: (7) ISDR->>SR: note over SR, ISDR **POST /<next-uri> HTTP/1.1 CRLF** … **X-Admin-Script-Status:** <script-status> CRLF CRLF <Body with ES8.EstablishISDPKeySet response: RC or error> End note SR->>DP:(8) sendData response with ES8.EstablishISDPKeySet response: RC or error Hnote over OP, ISDP #C0C0C0 (8a) Conditional: Error manageent, see 3.1.4 Endhnote rnote right of OP (9) Generates (eSK.DP.ECKA, ePK.DP.ECKA) Signs RC and ePK.DP.ECKA with SK.DP.ECDSA End rnote DP->>SR: (10) sendData( eid, sd-aid, ES8.keyEstablishISDPKeySet(ePK.DP.ECKA, signature)) SR->>ISDR: (11) Note over SR **HTTP/1.1 200 CRLF** … CRLF <Body with ES8.EstablishISDPKeySet(ePK.DP.ECKA, RC, signature)> End note ISDR->ISDP:(12) ePK.DP.ECKA, signature ISDP->ECASD rnote over ECASD 13) verifies signature using PK.DP.ECDSA. Continue if successful: - calculates ShS from ePK.DP.ECKA and SK.ECASD.ECKA. End rnote ECASD-->ISDP: (14) ShS or error rnote over ISDP (15) (Opt.) Generates DR Derives keyset from ShS (and DR) Calculates receipt. End rnote ISDP-->ISDR: (16) Receipt (Opt. DR) or error ISDR->>SR:(17) Note over SR, ISDR **POST** /<next-uri> **HTTP/1.1** CRLF … **X-Admin-Script-Status:** <script-status> CRLF CRLF <Body with ES8.EstablishISDPKeySet response: Receipt (Opt. DR) or error> End note SR->>DP:(18) sendData response with ES8.keyEstablishISDPKeySet response: Receipt (Opt. DR) or error hnote over OP, ISDP #C0C0C0 (18a) Conditional: Error management see 3.1.4 end hnote rnote right of OP (19) Calculates ShS from eSK.DP.ECKA and PK.ECASD.ECKA. Derives keyset from ShS (and DR) Verifies receipt End rnote @enduml Figure 12: Key Establishment, Scenario #3 Start Conditions: As a pre-condition, the ISD-P SHALL be created as defined in section 3.1.1, the eUICC/ECASD SHALL su … d. Else the ECASD SHALL calculate the ShS using the ePK.DP.ECKA and the SK.ECASD.ECKA. (14) The ShS or an error SHALL be returned to the ISD-P. (15) The ISD-P: … MAY MAY optionally compute a Derivation Random (DR, if requested by the SM-DP in the function call).  Derives the key set from ShS (and optionally DR).  Calculates th … dation of ephemeral keys. In addition, NIST SP 800-56A [50] provides requirements on the destruction of ephemeral keys and other intermediate secret data after … theirthe ir use.

3.1.3 Download and Installation of the Profilemodified

This section describes the third part of the procedure for the Profile Download and Installation step. The procedure illustrates the usage of RAM over HTTP as an example of the transport protocol. @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 160 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox DP->SR: (1) sendData(eid, isd-p-aid, [<data1>]<sub>scp03t</sub>, moreTodo) Rnote over SR #FFFFF (2) Check initial conditions Endrnote Hnote over SR, ISDR #C0C0C0 (2b) Conditional: HTTPS session opening End hnote SR->>ISDR: (3) note over SR,ISDR **HTTP/1.1 200 CRLF** … **X-Admin-Targeted-Application:**//aid/<rid>/<pix> (of ISD-P-AID)CRLF CRLF <Body with [<data1>]<sub>scp03t</sub> > End note ISDR->ISDP: (4) rnote over ISDP (5) Unwrap SCP03t security End rnote rnote over ISDP (6) Process Profile data End rnote ISDP-->ISDR: (6a) ISDR->>SR: (7) Note left of ISDP **POST** /<next-uri> **HTTP/1.1** CRLF … **X-Admin-Script-Status:** <script-status> CRLF CRLF <Body with [data1 execution response] <sub>scp03t</sub> > End note SR->>DP: (8) SendData response + [data1 execution response]<sub> scp03t</sub> Hnote over DP, ISDP #C0C0C0 (9) Optional: new data sending End hnote Hnote over OP, ISDP #C0C0C0 (9a) Conditional: Error management see 3.1.4 End hnote DP->SR: (10) profileDownloadCompleted(eid, iccid, subdAddress, POL2) rnote over SR (11) Update EIS End rnote SR-->DP Hnote over SR, ISDP #C0C0C0 (12) Optional: : Enable Profile see 3.3 End hnote DP->>OP: (13) Profile download &installation success SR->>M2MSP: (14) Cond: HandleProfileDownloadedNotification (eid, iccid, enabled) @enduml Figure 13: Download and Installation of the Profile Start Conditions: As a pre-condition, the ISD-P SHALL be created and personalized as defined in section 3.1. … e requires several steps. This optional step MAY be repeated as many times as required. (9a) In case of failure during the Download and Installation procedure, … the SM-DP SHALL execute the error management procedure describesdescribed in section 3.1.43.1.4. If this error management procedure fails to delete the ISD-P because the POL1 of the Profile prevented the deletion, the SM-DP shall consider that the profile installation succeeded on the eUICC, and SHALL becontinue executedat step 10 below. Otherwise the SM-DP SHALL return the result as specified in section 3.1.4 and the procedure SHALL stop. (10) When Profile download is completed the SM-DP SHALL call the “ES3.ProfileDownloadCompleted” function. This basically indicates … . The Operator SHALL be able to specify the POL2 content even if it is empty. As requested by the Operator, after Profile installation the SCP03 key set of the … ISD-PISD -P MAY: i. Be retained by the SM-DP. In this case the Operator can instruct the SM-DP to hand over or delete the key set at a later point in time; ii. Be handed o… …

3.1.4 Error Management Sub-Routinemodified

…allation procedure (before the optional enabling of the Profile). The procedure illustrates the usage of RAM over HTTP as an example of the transport protocol. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 160 hide footbox participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF participant ECASD #FFFFFF endbox DP->>SR: (1) In case of failure, deleteIS DP(iccid) function Hnote over SR, ISDR #C0C0C0 (1a) Conditional: HTTPS session opening end hnote SR->>ISDR: (2) Note left of ISDP **HTTP/1.1 200** CRLF … CRLF <Body with ES5.DeleteProfile(isd-p-aid)> End note Rnote over ISDR #FFFFFF (3) Enforce POL1 Endrnote | Alt Unless POL1 rejects deletion Rnote over ISDR: (4) Delete ISD-P End ISDR->>SR: (5) Note left of ISDP **POST** /<next-uri> **HTTP/1.1** CRLF … **X-Admin-Script-Status:** <script-status> CRLF CRLF <Body with ES5.DeleteProfile response > End note SR->>DP: (6) ISD-P deletion result Alt Deletion failed due to POL1 Hnote over OP, SR #C0C0C0 (7a) Complete Download and Installation procedure, see 3.1.3 End hnote Else Otherwise DP->>OP: (7) Download failed End @end uml Figure 14: Error Management Sub-Routine Procedure: (1) In case of failure during the key establishment procedure or the Download Profile procedure, the SM-DP SH … taining the “ES5.DeleteProfile” function with the ICCID. The X-Admin-Targeted-Application parameter SHALL be omitted as the command is targeting the ISD-R. (3) … If the Profile is already completely installed, the ISD-R SHALL enforce POL1. If POL1 prevents the deletion of the target Profile, the ISD-R SHALL skip step 4. (4) The ISD-R SHALL delete the targeted ISD-P. (4)(5) The ISD-R SHALL return the execution response to the ISD-P deletion “ES5.DeleteProfile” within a new HTTP POST request addressed to the SM-SR. (5)(6) The SM-SR SHALL forward the status of the “ES3.DeleteISDP”to the SM-DP. (6)(7) TheIf failurethe deletion of the ISD-P was successful, the response message indicating the failure of the download SHALL be returned to the Operator. In case of a timeout of the “ES5.DeleteProfile”, the status of the download SHALL be reported as ‘Expired’. a. If the deletion of the ISD-P was prevented by POL1, the SM-DP shall consider that the profile download and installation succeeded on the eUICC, and SHALL continue the procedure 3.1.3. NOTE: In case the deletion of the ISD-P fails or expires (e.g. because the eUICC is out of coverage), or in case the SM-DP does not receive confirmation of the deletion (e.g. because sending the result (5) failed), the SM-DP will get a chance to delete the ISD-P and the potentially incomplete profile at the beginning of a subsequent Profile Download on the same eUICC, as described in section 3.1.5.

3.1.5 ISD-P Cleanup Sub-Routineadded

The next figure describes the alternate flow that an SM-DP SHALL follow to delete an ISD-P that it formerly failed to delete. NOTE 1: The case where a Cleanup fails due to POL1 is not covered here. NOTE 2: The case where a Profile with the same ICCID was incompletely downloaded to a different eUICC is not covered here. @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 160 hide footbox participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox OP->>DP: (1) downloadProfile(srid, eid, iccid, final state, profileType) DP->SR: (2) getEIS(eid) Rnote over SR #FFFFF (3) Retrieve EIS Endrnote SR-->DP: (4) Return EIS Alt [If the SM-DP detects an ISD-P that it created and still in an incomplete state] DP->>SR: (5alt) DeleteProfile(eid, iccid) Rnote over SR #FFFFF (6alt) Check initial conditions Endrnote SR-->>DP: Failed SR->>ISDR: (7alt) MT-SMS [ES5.DELETE command]SCP80 Rnote over ISDR #FFFFFF (8alt) Delete ISD-P Endrnote ISDR-->>SR: (9alt) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (10alt) Update EIS Endrnote SR-->>DP: (11alt) Profile deletion result End Rnote over DP #FFFFFF (5) Check eUICC eligibility Endrnote DP-->>OP: Failed DP->>SR: (6) createISDP(eid, iccid, mno -id,…) @enduml Figure 315-A: ISD-P cleanup at the beginning of a subsequent profile download Procedure: (1) 2) (3) (4) See section 3.1.1. (5alt) As per the EIS, or by comparing the EIS with its own records, the SM-DP determines that an ISD-P associated to this SM-DP is in an incomplete state (the profile download procedure did not complete nominally). The SM-DP SHALL then send a request “ES3.DeleteISDP” to the SM-SR to delete the incomplete ISD-P. (6alt) The SM-SR SHALL verify if the SM-DP request is acceptable (the verifications that the SM-SR SHALL perform are described in section5.4.9). If any of the conditions to be verified are not satisfied, the SM-SR SHALL return a response indicating a failure, and the procedure SHALL end. (7alt) The SM-SR SHALL send an MT-SMS containing the “ES5.DELETE” command with its relevant input data (see section 4.1.1.4) to the ISD-R. The SM-SR SHALL request a PoR to get the execution status of the “ES5.DELETE” command. (8alt) The ISD-R SHALL delete the targeted ISD-P and the contained Profile. (9alt) The ISD-R SHALL return the MO-SMS to the SM-SR containing the execution status of the “ES5.DELETE” command. (10alt)In case of successful execution, the SM-SR SHALL update the EIS to reflect the newly deleted Profile. (11alt) The SM-SR SHALL return the response to the “ES3.DeleteISDP” function to the SM- DP. (5)(6)… The SM-DP and SM-SR SHALL resume the procedure described in section 3.1.1

3.2.1 Normal Casemodified

The sequence flow in the Figure 15 describes the normal case where the target Profile can successfully be enabled. @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox OP1->>SR: (1) EnableProfile(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>OP1: Failed SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80 Rnote over ISDR #FFFFFF (4) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80 SR-->>OP1: Failed Rnote over ISDR #FFFFFF (5) Enable ISD-P Endrnote ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80 SR-->>OP1: (6a) Failed ISDR-->>DEV: (7) REFRESH, (UICC reset) Rnote over DEV, ISDR #FFFFFF (8) Network attachment with the enabled profile Endrnote | Hnote right of SR #FFFFFF (9) Notification procedure over SMS Endhnote | Rnote over SR #FFFFFF (10) Check POL2 Endrnote SR->>ISDR: (11) Cond.: MT-SMS [ES5.DELETE command]SCP80 Rnote over ISDR #FFFFFF (11a) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.DELETE command FAILED response]SCP80 SR-->>OP1: Failed Rnote over ISDR #FFFFFF (11b) Delete disabled ISD-P and contained profile Endrnote ISDR-->>SR: (11c) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (12) Update EIS Endrnote SR-->>OP1: (13) Profile enabling result SR->>OP2: (14) HandleProfileDisabledNotification(eid, iccid2) SR->>M2MSP: (15) HandleProfileEnabledNotification (eid, iccid) SR->>M2MSP: (16) HandleProfileDisabledNotification (eid, iccid2) @enduml Figure 15: Profile Enabling, Success Case Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1 … command for Profile enabling with its relevant input data (see section 4.1.1.2) to the ISD-R. The SM-SR SHALL request a PoR to get the execution status of the … “ES5.STORE“ ES5.STORE DATA” command. (4) The ISD-R SHALL enforce POL1 of the currently Enabled Profile. If POL1 rejects enabling of the target Profile, the ISD-R SHALL return directl … ation (after having exhausted all possible retries), or doesn’t receive the SM-SR notification confirmation, this SHALL be considered as a fatal error, and the … previousprevio us note SHALL apply. On reception of the SM-SR notification confirmation command, if POL1 of the now Disabled Profile contains the rule “Profile deletion is mandat … th its relevant input data (see section 4.1.1.4) to the ISD-R, targeting the Disabled Profile. The SM-SR SHALL request a PoR to get the execution status of the … “ES5.DELETE”“ ES5.DELETE” command. (11a) The ISD-R SHALL enforce POL1 of the target Profile. If POL1 rejects the deletion of the target Profile, the ISD-R SHALL return the MO-SMS contain … on to Operator1, indicating that the Profile has been enabled. (14) Unless Operator2 has set an ONC (Operator Notifications Configuration) to not receive those … notifications,thenotifications, the SM-SR SHALL send the “ES4.HandleProfileDisabledNotification” or “ES4.HandleProfileDeletedNotification” (if deletion was triggered by the evaluation of POL1 and… …

3.2.2 Connectivity Failure Casemodified

The sequence flow in the Figure 16 describes the case where the target Profile cannot provide connectivity after it is enabled, and when roll-back to the previously Enabled Profile occurs. @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “Operator1” as OP1 #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox OP1->>SR: (1) EnableProfile(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>OP1: Failed SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80 Rnote over ISDR #FFFFFF (4) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80 SR-->>OP1: Failed Rnote over ISDR #FFFFFF (5) Enable ISD-P Endrnote ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80 SR-->>OP1: (6a) Failed ISDR-->>DEV: (7) REFRESH, (UICC reset) Rnote over DEV, ISDR #FFFFFF (8) Network attachment with the enabled profile **fails** OR Notification procedure **fails** Endrnote | Hnote over ISDR #FFFFFF (9) Enable previous ISD-P Endhnote ISDR-->>DEV: (10) REFRESH, (UICC reset) Rnote over DEV, ISDR #FFFFFF (11) Network attachment with the enabled profile Endrnote | Hnote right of SR #FFFFFF (12) Notification procedure over SMS Endhnote | SR-->>OP1: (13) Profile enabling failure @enduml Figure 16: Profile Enabling failure, with roll-back Start Conditions: The start conditions are identical to section 3.2.1. Procedure: Steps (1), (2), (3), (4), … …

3.3.1 Normal Casemodified

The sequence flow in the 0 describes the normal case where the targeted Profile can successfully be enabled. @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox OP1->>DP: (0) Cond.: EnableProfile(eid, smsr-id, iccid) DP->>SR: (1) EnableProfile(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP1: Failed SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80 Rnote over ISDR #FFFFFF (4) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80 SR-->>DP: Failed DP-->>OP1: Failed Rnote over ISDR #FFFFFF (5) Enable ISD-P Endrnote ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80 SR-->>DP: (6a) Failed DP-->>OP1: Failed ISDR-->>DEV: (7) REFRESH, (UICC reset) Rnote over DEV, ISDR #FFFFFF (8) Network attachment with the enabled profile Endrnote | Hnote right of SR #FFFFFF (9) Notification procedure over SMS Endhnote | Rnote over SR #FFFFFF (10) Check POL2 Endrnote SR->>ISDR: (11) Cond.: MT-SMS [ES5.DELETE command]SCP80 Rnote over ISDR #FFFFFF (11a) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.DELETE command FAILED response]SCP80 SR-->>DP: Failed DP-->>OP1: Failed Rnote over ISDR #FFFFFF (11b) Delete disabled ISD-P and contained profile Endrnote ISDR-->>SR: (11c) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (12) Update EIS Endrnote SR-->>DP: (13) Profile enabling result SR->>OP2: (14) HandleProfileDisabledNotification(eid, iccid2) SR->>M2MSP: (15) HandleProfileEnabledNotification (eid, iccid) SR->>M2MSP: (16) HandleProfileDisabledNotification (eid, iccid2) DP-->>OP1: (17) Cond.: Profile enabling result @enduml Figure 17: Profile Enabling, Success Case Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1… …

3.3.2 Connectivity Failure Casemodified

The sequence flow in the Figure 18 describes the case where the targeted Profile cannot provide connectivity after it is enabled, and when roll-back to the previously Enabled Profile occurs. @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “Operator1” as OP1 #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox OP1->>DP: (0) Cond.: EnableProfile(eid, smsr-id, iccid) DP->>SR: (1) EnableProfile(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP1: Failed SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80 Rnote over ISDR #FFFFFF (4) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80 SR-->>DP: Failed DP-->>OP1: Failed Rnote over ISDR #FFFFFF (5) Enable ISD-P Endrnote ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80 SR-->>DP: (6a) Failed DP-->>OP1: Failed ISDR-->>DEV: (7) REFRESH, (UICC reset) Rnote over DEV, ISDR #FFFFFF (8) Network attachment with the enabled profile **fails** OR Notification procedure **fails** Endrnote | Hnote over ISDR #FFFFFF (9) Enable previous ISD-P Endhnote ISDR-->>DEV: (10) REFRESH, (UICC reset) Rnote over DEV, ISDR #FFFFFF (11) Network attachment with the enabled profile Endrnote | Hnote right of SR #FFFFFF (12) Notification procedure over SMS Endhnote | SR-->>DP: (13) Profile enabling failure DP-->>OP1: (14) Cond.: Profile enabling failure @enduml Figure 18: Profile Enabling, With Roll-Back Start Conditions: The start conditions are the same as in section 3.3.1. Procedure: Steps (0) and (1) are the same a… …

3.4 Profile Disablingmodified

…t can be also performed using other transport protocols. The sequence flow in the 0 describes the case where the targeted Profile can successfully be disabled. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox OP1->>SR: (1) DisableProfile(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>OP1: Failed SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80 Rnote over ISDR #FFFFFF (4) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80 SR-->>OP1: Failed Rnote over ISDR #FFFFFF (5) Disable ISD-P Endrnote ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80 SR-->>OP1: (6a) Failed ISDR-->>DEV: (7) REFRESH, (UICC reset) Rnote over DEV, ISDR #FFFFFF (8) Network attachment using profile with Fall-Back Attribute Endrnote | Hnote right of SR #FFFFFF (9) Notification procedure over SMS Endhnote | Rnote over SR #FFFFFF (10) Check POL2 Endrnote SR->>ISDR: (11) Cond.: MT-SMS [ES5.DELETE command]SCP80 Rnote over ISDR #FFFFFF (11a) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.DELETE command FAILED response]SCP80 SR-->>OP1: Failed Rnote over ISDR #FFFFFF (11b) Delete disabled ISD-P and contained profile Endrnote ISDR-->>SR: (11c) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (12) Update EIS Endrnote SR-->>OP1: (13) Profile disabling result SR->>OP2: (14) HandleProfileEnabledNotification(eid, iccid2) SR->>M2MSP: (15) HandleProfileDisabledNotification (eid, iccid) SR->>M2MSP: (16) HandleProfileEnabledNotification (eid, iccid2) @enduml Figure 19: Profile Disabling Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Procedure: … command for Profile disabling with its relevant input data (see section 4.1.1.3) to the ISD-R. The SM-SR SHALL request a PoR to get the execution status of the … “ES5.STORE“ ES5.STORE DATA” command. (4) The ISD-R SHALL enforce POL1 of the currently Enabled Profile. In case POL1 rejects disabling, the ISD-R SHALL return PoR containing the res… …

3.5 Profile Disabling Via SM-DPmodified

…dure “Disable Profile” described in section 3.4. The sequence flow in the Figure 20 describes the case where the targeted Profile can successfully be disabled. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox OP1->>DP: (0) DisableProfile(eid, smsr-id, iccid) DP->>SR: (1) DisableProfile(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP1: Failed SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80 Rnote over ISDR #FFFFFF (4) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80 SR-->>DP: Failed DP-->>OP1: Failed Rnote over ISDR #FFFFFF (5) Disable ISD-P Endrnote ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80 SR-->>DP: (6a) Failed DP-->>OP1: Failed ISDR-->>DEV: (7) REFRESH, (UICC reset) Rnote over DEV, ISDR #FFFFFF (8) Network attachment using profile with Fall-Back attribute Endrnote | Hnote right of SR #FFFFFF (9) Notification procedure over SMS Endhnote | Rnote over SR #FFFFFF (10) Check POL2 Endrnote SR->>ISDR: (11) Cond.: MT-SMS [ES5.DELETE command]SCP80 Rnote over ISDR #FFFFFF (11a) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.DELETE command FAILED response]SCP80 SR-->>DP: Failed DP-->>OP1: Failed Rnote over ISDR #FFFFFF (11b) Delete disabled ISD-P and contained profile Endrnote ISDR-->>SR: (11c) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (12) Update EIS Endrnote SR-->>DP: (13) Profile disabling result SR->>OP2: (14) HandleProfileEnabledNotification(eid, icci d2) SR->>M2MSP: (15) HandleProfileDisabledNotification (eid, iccid) SR->>M2MSP: (16) HandleProfileEnabledNotification (eid, iccid2) DP-->>OP1: (17) Profile disabling result @enduml Figure 20: Profile Disabling Via SM-DPSM -DP Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Procedure: (0) Operator1, the owner of … tion status “Executed-With Warning” indicating that the Profile has also been deleted. (14) Unless Operator2 has set an ONC to not receive those notifications, … thehethe SM-SR SHALL send the “ES4.HandleProfileEnabledNotification” to Operator2, the owner of the Profile with Fall-Back Attribute set that is now enabled. (15) The S… …

3.6 Profile and ISD-P Deletionmodified

…The procedure illustrates the usage of SMS as a possible transport protocol between SM-SR and eUICC, but can be also performed using other transport protocols. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox OP->>SR: (1) DeleteProfile(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>OP: Failed Rnote over SR, ISDR #ADD1B2 (3) Optional: If targeted profile is enabled, then execute function "ES4.DisableProfile" Endrnote SR-->>OP: Failed SR->>ISDR: (4) MT-SMS [ES5.DELETE command]SCP80 Rnote over ISDR #FFFFFF (5) Enforce POL1 Endrnote | Rnote over ISDR #FFFFFF (6) Delete ISD-P Endrnote ISDR-->>SR: (7) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (8) Update EIS Endrnote SR-->>OP: (9) Profile deletion result SR->>M2MSP: (10) Cond: HandleProfileDeletedNotification (eid, iccid) @enduml Figure 21: Profile and ISD-P Deletion Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. P … aluate POL2 of the target Profile. If any of the conditions to be verified are not satisfied, the SM-SR SHALL return a response indicating the failure, and the … procedureproce dure SHALL end. (3) The SM-SR SHALL check the state of the target Profile. If the target Profile is enabled and if POL2 of the target Profile allows it to be disable … ator. (10) The SM-SR SHALL send the "ES4.HandleProfileDeletedNotification" to a M2M SP, if authorised by the Operator who owns the Profile, indicating that the … profileprofil e has been deleted. If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by the Operator owning the Profile, the SM-SR SHALL se… …

3.7 Profile and ISD-P Deletion Via SM-DPmodified

…The procedure illustrates the usage of SMS as a possible transport protocol between SM-SR and eUICC, but can be also performed using other transport protocols. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox OP->>DP: (1) DeleteProfile(eid, iccid, smsr -id) DP->>SR: (2) DeleteProfile(eid, iccid) Rnote over SR #FFFFF (3) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP: Failed Rnote over SR, ISDR #ADD1B2 (4) Optional: If targeted profile is enabled, then execute function "ES4.DisableProfile" Endrnote SR-->>DP: Failed DP-->>OP: Failed SR->>ISDR: (5) MT-SMS [ES5.DELETE command]SCP80 Rnote over ISDR #FFFFFF (6) Enforce POL1 Endrnote | Rnote over ISDR #FFFFFF (7) Delete ISD-P Endrnote ISDR-->>SR: (8) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (9) Update EIS Endrnote SR-->>DP: (10) Profile deletion result SR->>M2MSP: (11) Cond: HandleProfileDeletedNotification (eid, iccid) DP-->>OP: (12) Profile deletion result @enduml Figure 22: Profile and ISD-P Deletion via SM-DP Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded U… …

3.8 SM-SR Changemodified

…n v.2.2.1 [6]  Update the HTTPS parameters of the admin agent in the ISD-R, as specified in GlobalPlatform Card Specification Amendment B [8]  Update the DNS … paramatersparameters if this feature is supported by the eUICC and SM- SR2  Erase the DNS parameters if this feature is not supported by SM-SR2.  Update the SM-SR addressing para … fore sending any enable or disable profile command, and it SHOULD perform this update as soon as possible (to cover the activation of the Fall-Back Mechanism). … NOTENOTE: SM-SR2 MAYSHOULD perform steps 25 and 26 in thea samesingle command scriptscript. SM- SR2 MAY provide the corresponding commands in any order. (27) The ISD-R SHALL return the result of the keys deletion (and the result of optional operations that have been sent at step 26) to SM-SR2. (28… …

3.10 Master Delete Proceduremodified

…The procedure illustrates the usage of SMS as a possible transport protocol between SM-SR and eUICC, but can be also performed using other transport protocols. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “Initiator” as INI #FFFFFF participant “SM-SR” as SR #FFFFFF participant “SM-DP” as DP #FFFFFF participant “Operator” as OP #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox INI->>SR: (1) Request for Master Delete \n(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>INI: Failed | SR->>DP: (3) Request for Master Delete Authorisation group Authorisation Hnote over DP, OP #FFFFF Requests authorisation (out of scope) Endhnote Rnote over DP #FFFFF (4) Check if the request is authorised and authenticated Endrnote end DP-->>SR: Refuse SR-->>INI: Refuse DP->>SR: (5) Master Delete Authorisation response\n (Delete Token) SR->>ISDR: (6) MT-SMS [ES5.MasterDelete command](Delete Token) Rnote over ISDR #FFFFF (7) Check conditions Endrnote ISDR-->>SR: Failed SR-->>INI: Failed Rnote over ISDR, ISDP #FFFFF (8) ISD-P verifies the Token and ISD-R deletes ISD-P and contained profile Endrnote ISDR-->>SR: (9) MO-SMS [ES5.MasterDelete command response] Rnote over SR #FFFFFF (10) Update EIS Endrnote SR-->>INI: (11) Profile deletion result @enduml Figure 25: Master Delete Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1], plus: c) The t… …

3.11 POL2 Update Via SM-DPmodified

This procedure is used by the Operator to update POL2 via the SM-DP. @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF OP->>DP: (1) UpdatePolicyRules(POL2) DP->>SR: (2) UpdatePolicyRules(POL2) Rnote over SR #FFFFF (3) Update POL2 Endrnote SR-->>DP: (4) UpdatePolicyRules Result SR->>M2MSP: (5) Cond: HandleProfilePOL2UpdatedNotification (eid, iccid, POL2) DP-->>OP: (6) UpdatePolicyRules Result @enduml Figure 26: POL2 Update Via SM-DPSM -DP Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Procedure: (1) The Operator owner of the target Profile SHALL call the “ES2.UpdatePolicyRules”“ ES2.UpdatePolicyRules” function with its relevant input data, as described in section 5.3.3, in particular the identification of the SM-SR in charge of the management of the target e… …

3.12 POL1Update by Operatormodified

…cedure illustrates the usage of SMS as a possible transport protocol between the Operator and eUICC, but can be also performed using other transport protocols. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “Operator” as OP #FFFFFF box “eUICC” #FFFFFF participant “MNO-SD” as MNO #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox OP->>MNO: (1) MT-SMS [POL1UpdateByMNO command]SCP80 (POL1) | MNO->>ISDP: (2) POL1 Update command (POL1) Rnote over ISDP #FFFFF (3) ISD-P Update POL1 Endrnote ISDP-->>MNO: (4) POL1 Update command response | MNO-->>OP: (5) MO-SMS [POL1UpdateByMNO command response]SCP80 @enduml Figure 27: POL1 Update Via Operator Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Procedure: (1) The Operator owning the target Profile SHALL send a MT-SMSMT -SMS containing the “ES6.UpdatePOL1byMNO” function with its relevant input data (as described in section 4.1.2.1). (2) The MNO-SD receives this request and SHALL tr… …

3.13 Connectivity Parameters Update by Operatormodified

…cedure illustrates the usage of SMS as a possible transport protocol between the Operator and eUICC, but can be also performed using other transport protocols. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “Operator” as OP #FFFFFF box “eUICC” #FFFFFF participant “MNO-SD” as MNO #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox OP->>MNO: (1) MT-SMS [Connectivity Parameters]SCP80 | MNO->>ISDP: (2) Connectivity Parameters Update command Rnote over ISDP #FFFFF (3) ISD-P Update Connectivity Parameters Endrnote ISDP-->>MNO: (4) Connectivity Parameters Update response | MNO-->>OP: (5) MO-SMS [Connectivity Parameters Update command response]SCP80 @enduml Figure 28: Connectivity Parameters Update by Operator Start condition: The Operator wants to update the Connectivity Parameters in their Profile Procedure: (1) The Operator owning the target Profile SHALL send a MT-SMSMT -SMS containing the Connectivity Parameters to the MNO-SD. (2) The MNO-SD SHALL transfer the Connectivity Parameters to the ISD-P. (3) The ISD-P SHALL update the Co… …

3.14 Connectivity Parameters Update Using SCP03modified

…ocol between the SM- SR and eUICC, where ISD-R is in charge of encapsulating the data in SCP80,. Other transport protocols such as HTTPS or CAT-TP can be used. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “Operator/SM-DP” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox OP->>SR: (1) UpdateConnectivityParametersSCP03\nCommand(Connectivity Parameters SCP03) SR->>ISDR: (2) MT-SMS [Connectivity Parameters SCP03]SCP80 ISDR->>ISDP: (3) (Connectivity Parameters SCP03) Rnote over ISDP #FFFFF (4) ISD-P Update Connectivity Parameters Endrnote ISDP-->>ISDR: (5) Connectivity Parameters Update response | ISDR-->>SR: (6) MO-SMS [Connectivity Parameters Update command response]SCP80 SR-->>OP: (7) UpdateConnectivityParametersSCP03 Result @enduml Figure 29: Connectivity Parameters Update Using SCP03 The start conditions are described in [1]. (1) The Operator, or the SM-DP, on behalf of the Operator ownin… …

3.16 Fall-Back Activation Proceduremodified

… enabled Profile is the Emergency Profile or the Test Profile, the eUICC SHALL NOT activate the Fall-Back Mechanism, until the Local Disable command is called. … @startuml skinparam monochrome true skinparam ArrowColor Black hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “SM-SR” as SR #FFFFFF participant Device #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox rnote over ISDR (1) Triggering Fall-Back Mechanism End rnote rnote over ISDR (2) Disable current Profile. Enable Fall-Back Profile. End rnote ISDR->>Device: (3) REFRESH (UICC reset) Hnote right of Device #C0C0C0 (4) Network attach with the enabled profile End hnote Hnote over SR, ISDR #C0C0C0 (5) Notification procedure End hnote Rnote over SR (6) EIS Update End rnote SR->OP2: (7) Cond: handleProfileEnabledNotification(eid, iccid2) SR->OP1: (8) Cond: handleProfileDisabledNotification(eid, iccid) SR->>M2MSP: (9) Cond: HandleProfileEnabledNotification (eid, iccid2) SR->>M2MSP: (10) Cond: HandleProfileDisabledNotification (eid, iccid) @enduml Figure 32: Fall-Back Activation Procedure Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1 … -Back Attribute set has been enabled  The previously Enabled Profile has been disabled (7) Unless Operator1 has set an ONC to not receive those notifications, … theSM-SRthe SM-SR SHALL send the “ES4.HandleProfileEnabledNotification” to Operator2, the owner of Profile with the Fall-Back Attribute set that is now enabled. In case Operator… …

3.17.1 Normal Casemodified

The sequence flow in the figure below describes the normal case where the target Profile can successfully be enabled. @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox M2MSP->>SR: (1) EnableProfile(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->> M2MSP: Failed SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80 Rnote over ISDR #FFFFFF (4) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80 SR-->> M2MSP: Failed Rnote over ISDR #FFFFFF (5) Enable ISD-P Endrnote ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80 SR-->> M2MSP: (6a) Failed ISDR-->>DEV: (7) REFRESH, (UICC reset) Rnote over DEV, ISDR #FFFFFF (8) Network attachment with the enabled profile Endrnote | Hnote right of SR #FFFFFF (9) Notification procedure over SMS Endhnote | Rnote over SR #FFFFFF (10) Check POL2 Endrnote SR->>ISDR: (11) Cond.: MT-SMS [ES5.DELETE command]SCP80 Rnote over ISDR #FFFFFF (11a) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.DELETE command FAILED response]SCP80 SR-->>M2MSP: Failed Rnote over ISDR #FFFFFF (11b) Delete disabled ISD-P and contained profile Endrnote ISDR-->>SR: (11c) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (12) Update EIS Endrnote SR-->>M2MSP: (13) Profile enabling result SR->>OP1: (14) Cond: HandleProfileEnabledNotification (eid, iccid) SR->>OP2: (15) Cond: HandleProfileDisabledNotification(eid2, iccid2) SR->>M2MSP: (16) Cond: HandleProfileDisabledNotification(eid 2, iccid2) @enduml Figure 33: Profile Enabling via M2M SP, Success Case Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embed … command for Profile enabling with its relevant input data (see section 4.1.1.2) to the ISD-R. The SM-SR SHALL request a PoR to get the execution status of the … “ES5.STORE“ ES5.STORE DATA” command. (4) The ISD-R SHALL enforce POL1 of the currently Enabled Profile. If POL1 rejects enabling of the target Profile, the ISD-R SHALL return directl … th its relevant input data (see section 4.1.1.4) to the ISD-R, targeting the Disabled Profile. The SM-SR SHALL request a PoR to get the execution status of the … “ES5.DELETE”“ ES5.DELETE” command. (11a) The ISD-R SHALL enforce POL1 of the target Profile. If POL1 rejects the deletion of the target Profile, the ISD-R SHALL return the MO-SMS contai… …

3.17.2 Connectivity Failure Casemodified

The sequence flow in the figure below describes the case where the target Profile cannot provide connectivity after it is enabled, and when roll-back to the previously Enabled Profile occurs. @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP1 #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox M2MSP->>SR: (1) EnableProfile(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>M2MSP: Failed SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80 Rnote over ISDR #FFFFFF (4) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80 SR-->>M2MSP: Failed Rnote over ISDR #FFFFFF (5) Enable ISD-P Endrnote ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80 SR-->>M2MSP: (6a) Failed ISDR-->>DEV: (7) REFRESH, (UICC reset) Rnote over DEV, ISDR #FFFFFF (8) Network attachment with the enabled profile **fails** OR Notification procedure **fails** Endrnote | Hnote over ISDR #FFFFFF (9) Enable previous ISD-P Endhnote ISDR-->>DEV: (10) REFRESH, (UICC reset) Rnote over DEV, ISDR #FFFFFF (11) Network attachment with the enabled profile Endrnote | Hnote right of SR #FFFFFF (12) Notification procedure over SMS Endhnote | SR-->>M2MSP: (13) Profile enabling failure @enduml Figure 34: Profile Enabling via M2M SP, Failure Case with roll-back Start Conditions: The start conditions are identical to section 3.17.1 Procedure: Steps (1), … ew network attach procedure with the Profile Enabled before the start of the procedure. (12) The eUICC SHALL perform the notification procedure as described in … sectionsectio n 4.1.1.11. On reception of the SMS notification, the SM-SR is informed that the target Profile has not been enabled. (13) Finally, the SM-SR SHALL return the re… …

3.18 Profile Disabling via M2M SPmodified

…rformed using other transport protocols. The sequence flow in the figure below describes the normal case where the target Profile can successfully be disabled. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox M2MSP->>SR: (1) DisableProfile(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>M2MSP: Failed SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80 Rnote over ISDR #FFFFFF (4) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80 SR-->>M2MSP: Failed Rnote over ISDR #FFFFFF (5) Disable ISD-P Endrnote ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80 SR-->>M2MSP: (6a) Failed ISDR-->>DEV: (7) REFRESH, (UICC reset) Rnote over DEV, ISDR #FFFFFF (8) Network attachment using profile with Fall-Back attribute Endrnote | Hnote right of SR #FFFFFF (9) Notification procedure over SMS Endhnote | Rnote over SR #FFFFFF (10) Check POL2 Endrnote SR->>ISDR: (11) Cond.: MT-SMS [ES5.DELETE command]SCP80 Rnote over ISDR #FFFFFF (11a) Enforce POL1 Endrnote ISDR-->>SR: MO-SMS [ES5.DELETE command FAILED response]SCP80 SR-->>M2MSP: Failed Rnote over ISDR #FFFFFF (11b) Delete disabled ISD-P and contained profile Endrnote ISDR-->>SR: (11c) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (12) Update EIS Endrnote SR-->>M2MSP: (13) Profile disabling result SR->>OP1: (14) Cond: HandleProfileDisabledNotification(eid, iccid ) SR->>OP2: (15) Cond: HandleProfileEnabledNotification(eid, iccid2) SR->>M2MSP: (16) Cond: HandleProfileEnabledNotification(eid, iccid2) @enduml Figure 35: Profile Disabling via M2M SP Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. … command for Profile disabling with its relevant input data (see section 4.1.1.3) to the ISD-R. The SM-SR SHALL request a PoR to get the execution status of the … “ES5.STORE“ ES5.STORE DATA” command. (4) The ISD-R SHALL enforce POL1 of the currently Enabled Profile. In case POL1 rejects disabling, the ISD-R SHALL return PoR containing the resp … in UICC reset mode to the Device. This will trigger the execution of a network attach procedure. NOTE: In case of any error after this step indicating that the … currentcurr ent Enabled Profile cannot provide connectivity, the ISD-R SHALL re-enable the previously Enabled Profile as described in section 3.2.2. (8) The eUICC and the Devic … R SHALL delete the disabled ISD-P and the contained Profile. The eUICC SHALL send the response to the notification confirmation indicating whether the disabled … ISD-PISD -P has been deleted or not. (10) On reception of the ES5.HandleNotificationConfirmation response, and if the ES5.HandleNotificationConfirmation response indicates … th its relevant input data (see section 4.1.1.4) to the ISD-R, targeting the Disabled Profile. The SM-SR SHALL request a PoR to get the execution status of the … “ES5.DELETE”“ ES5.DELETE” command. (11a) The ISD-R SHALL enforce POL1 of the target Profile. If POL1 rejects the deletion of the target Profile, the ISD-R SHALL return the MO-SMS contai… …

3.19 Profile and ISD-P Deletion via M2M SPmodified

…erformed using other transport protocols. The sequence flow in the figure below describes the normal case where the target Profile can successfully be deleted. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox M2MSP->>SR: (1) DeleteProfile(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>M2MSP: Failed Rnote over SR, ISDR #ADD1B2 (3) Optional: If targeted profile is enabled, then execute function "ES4.DisableProfile" Endrnote SR-->>M2MSP: Failed SR->>ISDR: (4) MT-SMS [ES5.DELETE command]SCP80 Rnote over ISDR #FFFFFF (5) Enforce POL1 Endrnote | Rnote over ISDR #FFFFFF (6) Delete ISD-P Endrnote ISDR-->>SR: (7) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (8) Update EIS Endrnote SR-->>M2MSP: (9) Profile deletion result SR->>OP: (10) HandleProfileDeletedNotifi cation(eid, iccid) @enduml Figure 36: Profile and ISD-P Deletion via M2M SP Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded … een deleted. (10) Unless the Operator has set an ONC to not receive those notifications, the SM-SR SHALL send the “ES4.HandleProfileDeletedNotification” to the … Operaor,Operator, the owner of the Profile. In case the Operator has no direct connection with the SM-SR (SM-SR SHALL be able to detect such a situation based on its own databas… …

3.20.1 Set Profile Lifecycle Management Authorisationmodified

… SP - If no PLMA is configured in the SM-SR for a given set of identifiers, then no authorisations SHALL be granted to any other function caller apart from the … OperatorOperat or who is owning the targeted Profiles. The sequence flow in the figure below describes the procedure. @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF OP->>SR: (1) SetPLMA(identifiers, PLMA) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>OP: Failed Rnote over SR #FFFFFF (3) Store PLMA Endrnote SR-->>OP: (4) SetPLMA result SR->>M2MSP: (5) HandlePLMAChangedNotification (identifiers) @enduml Figure 37: Set PLMA Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Procedure: (1) To … …

3.20.2 Set Profile Lifecycle Management Authorisation rules via SM-DPmodified

…he procedure “Set Profile Lifecycle Management Authorisation rules” described in section 3.20.1. The sequence flow in the figure below describes the procedure. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF OP->>DP: (1) SetPLMA(identifiers, PLMA) DP->>SR: (2) SetPLMA(identifiers, PLMA) Rnote over SR #FFFFF (3) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP: Failed Rnote over SR #FFFFFF (4) Store PLMA Endrnote SR-->>DP: (5) SetPLMA result SR->>M2MSP: (6) HandlePLMAChangedNotification (identifiers) DP-->>OP: (7) SetPLMA result @enduml Figure 38: Set PLMA via SM-DPSM -DP Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Procedure: (1) To set a PLMA for a M2M… …

3.20.3 Retrieve Profile Lifecycle Management Authorisation by Operatormodified

…t of the function call provides back the granted PLMA(s) based on the provided input parameters. The sequence flow in the figure below describes the procedure. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF OP->>SR: (1) GetPLMA(identifiers) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>OP: Failed Rnote over SR #FFFFFF (3) Retrieve PLMA Endrnote SR-->>OP: (4) GetPLMA result (PLMA) @enduml Figure 39: Retrieve PLMA by Operator Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Pr … he targeted Profile or Profile Type, the call may still be valid, but in this case the calling Operator is merely acting as an M2M SP, similar to the procedure … decribeddescribed in section 3.20.5. The checks the SM-SR shall perform in this case are described in section 5.5.17. (3) The SM-SR retrieves the PLMA(s) matching with the ident… …

3.20.4 Retrieve Profile Lifecycle Management Authorisation by Operator via SM-DPmodified

…t of the function call provides back the granted PLMA (s) based on the provided input parameters The sequence flow in the figure below describes the procedure. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF OP->>DP: (1) GetPLMA(identifiers) DP->>SR: (2) GetPLMA(identifiers) Rnote over SR #FFFFF (3) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP: Failed Rnote over SR #FFFFFF (4) Retrieve PLMA Endrnote SR-->>DP: (5) GetPLMA result (PLMA) DP-->>OP: (6) GetPLMA result (PLMA) @enduml Figure 40: Retrieve PLMA by Operator via SM-DPSM -DP Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Procedure: (1) To retrieve the PLMA(s)… …

3.20.5 Retrieve Profile Lifecycle Management Authorisation by M2M SPmodified

… of the function call provides back the granted PLMA (s) based on the provided input parameters. The sequence flow in the figure below describes the procedure. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “SM-SR” as SR #FFFFFF M2MSP->>SR: (1) GetPLMA(identifiers) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>M2MSP: Failed Rnote over SR #FFFFFF (3) Retrieve PLMA Endrnote SR-->>M2MSP: (4) GetPLMA result (PLMA) @enduml Figure 41: Retrieve PLMA by M2M SP Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Proc… …

3.21.1 Set Operator Notifications Configurationmodified

…ve all notifications for status changes for its own Profiles, associated with this Profile Type. The sequence flow in the figure below describes the procedure. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF OP->>SR: (1) SetONC (identifiers, notifications list) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>OP: Failed Rnote over SR #FFFFFF (3) Store Operator Notification Configuration Endrnote SR-->>OP: (4) SetONC result @enduml Figure 3211-A: Set Operator Notification Configuration Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Emb… …

3.21.2 Set Operator Notifications Configuration via SM-DPmodified

…is done through the SM-DP (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.15.1). The procedure is initiated by the Operator owning … thet he targeted Profile Type and is similar to the procedure “Set Operator Notification Configuration” described in section 3.21.1. The sequence flow in the figure below describes the procedure. @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF OP->>DP: (1) SetONC (identifiers, notifications list) DP->>SR: (2) SetONC(identifiers, notifications list) Rnote over SR #FFFFF (3) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP: Failed Rnote over SR #FFFFFF (4) Store Operator Notification Configuration Endrnote SR-->>DP: (5) SetONC result DP-->>OP: (6) SetONC result @enduml Figure 42: Set Operator Notification Configuration via SM-DP Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for … …

3.21.3 Retrieve Operator Notifications Configurationmodified

…s will be sent for Profiles assigned with this Profile Type, see also section 5.7.4 for details. The sequence flow in the figure below describes the procedure. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF OP->>SR: (1) GetONC (identifiers, notifications list) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>OP: Failed Rnote over SR #FFFFFF (3) Retrieve Operator Notification Configuration Endrnote SR-->>OP: (4) GetONC result @enduml Figure 43: Retrieve Operator Notification Configuration Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Em… …

3.21.4 Retrieve Operator Notifications Configuration via SM-DPmodified

…s will be sent for Profiles assigned with this Profile Type, see also section 5.7.4 for details. The sequence flow in the figure below describes the procedure. … @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF OP->>DP: (1) GetONC (identifiers, notifications list) DP->>SR: (2) GetONC (identifiers, notifications list) Rnote over SR #FFFFF (3) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP: Failed Rnote over SR #FFFFFF (4) Retrieve Operator Notification Configuration Endrnote SR-->>DP: (5) GetONC result DP-->>OP: (6) GetONC result @enduml Figure 44: Retrieve Operator Notification Configuration via SM-DP Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture … …

3.22 Local Enable for Test Profilemodified

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 120 skinparam sequenceArrowThickness 1 hide footbox participant “Device” as DEV #FFFFFF participant “eUICC” as eUICC #FFFFFF DEV->>eUICC : (1) ESx.LocalEnableTestProfile Rnote over eUICC #FFFFF (2) Verify that the Test Profile exists Endrnote eUICC-->>DEV : Error Rnote over eUICC #FFFFF (3) Verify that the currently Enabled Profile is NOT the Emergency Profile Endrnote eUICC-->>DEV : Error Rnote over eUICC #FFFFF (4) Verify that the currently Enabled Profile is NOT the Test Profile Endrnote eUICC-->>DEV : Error Group Profile switch Rnote over eUICC #FFFFF (5) Enable Test Profile Endrnote eUICC-->>DEV : (6) Success | eUICC-->>DEV: (7) REFRESH, (UICC reset) | Rnote over DEV, eUICC #FFFFFF (8) Network attachment with the Enabled Profile Endrnote end @enduml Figure 322: Local Enable of Test Profile Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Procedure: (1) The Device SHALL call the “ESX.LocalEnableTestProfile”“ESx.LocalEnableTestProfile” function. (2) The eUICC SHALL verify that the Profile is the Test Profile exists (including Flag and NAA keys as described in EUICC23 in SGP.01 [1]). If any of the conditions to be verified are not satisfied, the eUICC SHALL return a respons … e. If the condition to be verified is not satisfied, the eUICC SHALL return a response indicating the failure, and the procedure SHALL end. (4) The eUICC SHALL … verify that the currently enabled Profile is NOT the Test Profile. If the condition to be verified is not satisfied, the eUICC SHALL return a response indicating that the Test Profile is already Enabled, and the procedure SHALL end. (5) The eUICC SHALL NOT enforce POL1 of the currently Enabled Profile, and SHALL disable the currently enabled Profile, and enable the Test Profile. NOTE: Profile change includes a change of the IMSI that is used to attach to the network. As … read by the terminal. So while the Profile is marked as enabled in this step, it MAY actually become effective after the terminal executes the REFRESH command. … (5)(6) The eUICC SHALL return the execution status of the “ESX.“ ESx. LocalEnableTestProfile” command to the Device. (6)(7) The eUICC SHALL send a REFRESH proactive command in UICC reset mode to the Device. This will trigger the execution of a network attach procedure. (7)(8) The Device SHALL perform a network attach procedure with the newly enabled Profile. NOTE: Whether the Test Profile provides connectivity to a test network or n… …

3.23 Local Disable for Test Profilemodified

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 100 skinparam sequenceArrowThickness 1 hide footbox participant “Device” as DEV #FFFFFF participant “eUICC” as ISDR #FFFFFF DEV->>ISDR : (1) ESx.LocalDisableTestProfile Rnote over ISDR #FFFFF (2) Verify that the currently Enabled Profile is the Test Profile Endrnote ISDR-->>DEV : Error group Profile switch Rnote over ISDR #FFFFF (3) Disable Test Profile and enable previously Enabled Profile Endrnote ISDR-->>DEV : (4) Success | ISDR-->>DEV: (5) REFRESH, (UICC reset) | Rnote over DEV, ISDR #FFFFFF (6) Network attachment with the Enabled Profile Endrnote End @enduml Figure 323: Local Disable of Test Profile Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Procedure: (1) The Device SHALL call the “ESX.LocalDisableTestProfile”“ESx.LocalDisableTestProfile” function. (2) The eUICC SHALL verify that the currently Enabled Profile is the Test Profile (including Flag and NAA keys as described in EUICC23 in SGP.01[1]). If any of the conditions to be verified are not satisfied, the eUICC SHALL return a response indicating that the failure,currently Enabled Profile is not the Test Profile, and the procedure SHALL end. (3) The eUICC SHALL disable the Test Profile and enable the previously enabled Profile. (4) The eUICC SHALL return the execution status of the “ESX.LocalDisableTestProfile”“ ESx.LocalDisableTestProfile” command to the Device. (5) The eUICC SHALL send a REFRESH proactive command in UICC reset mode to the Device. This will trigger the execution of a network attac … e is the Profile that was enabled before the Local Enable. (6) The eUICC and the Device SHALL perform a network attach procedure with the newly Enabled Profile. … Dependent on the configuration of the eUICC, the eUICC MAY send a Notification about the Profile change after Test Profile disabling to the SM-SR.

3.24 POL2 Updatemodified

This procedure is used by the Operator to update POL2 via the SM-SR. @startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1 hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF OP->>SR: (1) UpdatePolicyRules(POL2) Rnote over SR #FFFFF (2) Update POL2 Endrnote SR-->>OP: (3) UpdatePolicyRules Result SR->>M2MSP: (4) Cond: HandleProfilePOL2UpdatedNotification (eid, iccid, POL2) @enduml Figure 324: POL2 Update Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Procedure: (1) The Operator owner of the target Profile SHALL call the “ES4.UpdatePolicyRules”“ ES4.UpdatePolicyRules” function with its relevant input data, as described in section 5.3.3. (2) The SM-SR SHALL update the POL2 of the targeted eUICC’s EIS. (3) The SM-SR SHALL retu… …

3.25 Emergency Profile Attribute Managementmodified

…ergency Profile Attribute is only unset as a consequence of setting the Emergency Profile Attribute on another Profile. For case 1 the procedure below applies: … @startuml skinparam monochrome true skinparam ArrowColor Black hide footbox Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-DP” as DP #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF Alt [via SM-SR] OP2->SR: [1.a] ES4.SetEmergencyProfileAttribute(EID,ICCID)\non Profile B Request Else [via SM-DP] OP2->DP: [1.b] ES2.SetEmergencyProfileAttribute(EID,SMSR -ID,ICCID)\non Profile B Request Rnote over DP #FFFFFF Identify SM-SR Endrnote DP<->SR: Mutual Authentication DP->SR: [1.c] ES3.SetEmergencyProfileAttribute(EID,ICCID) \non Profile B Request end SR->EUICC: [2] ES5.SetEmergencyProfileAttribute(ISD -P AID)\non Profile B Rnote over EUICC #FFFFFF [3a] Verify if Profile B has not set Fall -Back Attribute Endrnote EUICC-->SR: [3.a] Send STORE DATA response indicating an error Rnote over EUICC #FFFFFF [3b] Set Emergency Profile Attribute on Profile B Endrnote EUICC->SR: [4] SetEmergencyProfileAttribute response Rnote over SR #FFFFFF [5] EIS Update(AdditionalProperty) Endrnote Alt [via SM-SR] SR->OP2: 6.a] ES4.HandleEmergencyProfileAttributeSetNotification \non Profile B Request SR->OP1 Else [via SM-DP] SR->DP: [6.b] ES3.SetEmergencyProfileAttribute(EID,ICCID) \non Profile B Request DP->OP2: [6.c] ES2.HandleEmergencyProfileAttributeSetNotification\non Profile B Request end Opt [If if requested by Operator 2] SR->SP: [7] HandleEmergencyProfileAttributeSetNotification of Profile B end @enduml Figure 325-A: Emergency Profile Attribute Management (case 1: first Emergency Profile) Start Conditions (case 1): a. No Profile with Emergency Profile Attribute … vant input parameters and the SM-DP forwarding the request to the SM-SR (1c) by calling the “ES3.SetEmergencyProfileAttribute” function with the relevant input … parametersparameters. . (2) The SM-SR, by calling the “ES5.SetEmergencyProfileAttribute” function, requests the eUICC to set the Emergency Profile Attribute to the Profile B. (3) The e … ergencyProfileAttributeSetNotification”. End Conditions (case 1): The Profile B has the Emergency Profile Attribute set. For case 2 the procedure below applies … @startuml skinparam monochrome true skinparam ArrowColor Black hide footbox Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-DP” as DP #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF Alt [via SM-SR] OP2->SR: [1.a] ES4.SetEmergencyProfileAttribute(EID,ICCID)\non Profile B Request Else [via SM-DP] OP2->DP: [1.b] ES2.SetEmergencyProfileAttribute(EID,SMSR -ID,ICCID)\non Profile B Request Rnote over DP #FFFFFF Identify SM-SR Endrnote DP<->SR: Mutual Authentication DP->SR: [1.c] ES3.SetEmergencyProfileAttribute(EID,ICCID) \non Profile B Request end Rnote over SR #FFFFFF [2] Check PLMA for SetmergencyProfileAttribute for Operator 2 Endrnote SR-->OP2: [2.a] Send error response with authorisation conflict SR->EUICC: [3] ES5.SetEmergencyProfileAttribute(ISD -P AID)\non Profile B Rnote over EUICC #FFFFFF [4a] Verify if Profile B has not set Fall -Back Attribute Endrnote EUICC-->SR: [4.a] send STORE DATA error response Rnote over EUICC #FFFFFF [4b] Unset Emergency Profile Attribute on Profile A by Setting Emergency Profile Attribute on Profile B Endrnote EUICC->SR: [5] SetEmergencyProfileAttribute response Rnote over SR #FFFFFF [6] EIS Update(AdditionalProperty) Endrnote SR->OP1: [7] ES4.HandleEmergencyProfileAttributeU nsetNotification\non Profile A Alt [via SM-SR] SR->OP2: [8.a] ES4.HandleEmergencyProfileAttributeSetNotification \non Profile B SR->OP1 Else [via SM-DP] SR->DP: [8.b] ES3.HandleEmergencyProfileAttributeSetNotification \non Profile B DP->OP2: [8.c] ES2.HandleEmergencyProfileAttributeSetNotification \non Profile B end Opt [If if requested by Operator 1] SR->SP: [9] HandleEmergencyProfileAttributeUnsetNotification of Profile A End Opt [If if requested by Operator 2] SR->SP: [10] HandleEmergencyProfileAttributeSetNotification of Profile B end @enduml Figure 325-B: Emergency Profile Attribute Management (case 2: change of Emergency Profile) Start Conditions (case 2): a. Profile A with Emergency Profile Attrib … the “ES2.HandleEmergencyProfileAttributeSetNotification”, that a Profile now has the Emergency Profile Attribute set. This notification MAY include the Profile … ID..ID. (9) The SM-SR SHALL notify the M2M SP that the Profile A has the Emergency Profile Attribute unset by calling the “ES4.HandleEmergencyProfileAttributeUnsetNoti … ing the “ES3. HandleEmergencyProfileAttributeUnsetNotification”. Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting as … theth e M2M SP, by calling the “ES2. HandleEmergencyProfileAttributeUnsetNotification”. (10) The SM-SR SHALL notify the M2M SP that the Profile B has the Emergency Pro… …

3.26 Emergency Profile Attribute Management via the M2M SPmodified

…ergency Profile Attribute is only unset as a consequence of setting the Emergency Profile Attribute on another Profile. For case 1 the procedure below applies: … startuml skinparam monochrome true skinparam ArrowColor Black hide footbox Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF SP->SR: [1] ES4.SetEmergencyProfileAttribute(EID,ICCID) \non Profile B Request Rnote over SR #FFFFFF [2] Check PLMA for Setting Emergency Profile Attribute from Operator 2 Endrnote SR-->SP: [2.a] Send response indicating authorisation conflict SR->EUICC: [3] ES5.SetEmergencyProfileAttribute(ISD -P AID)\non Profile B Rnote over EUICC #FFFFFF [4a] Verify if Profile B has not set Fall -Back Attribute Endrnote EUICC-->SR: [4.a] send STORE DATA response with herror Rnote over EUICC #FFFFFF [4b] Set Emergency Profile Attribute on Profile B Endrnote EUICC->SR: [5] SetEmergencyProfileAttribute response Rnote over SR #FFFFFF [6] EIS Update(AdditionalProperty) Endrnote SR->OP2: [7] ES4.HandleEmergencyProfileAttribute SetNotification of Profile B SR->OP1 SR->SP: [8] ES4.HandleEmergencyProfileAttributeSetNotification of Profile B @enduml Figure 326-A: Emergency Profile Attribute Management by M2M SP (case 1: first Emergency Profile) Start Conditions: a. Profile B, targeted to have the Emergency … quests setting of the Emergency Profile Attribute on Profile B to the SM- SR by calling the “ES4.SetEmergencyProfileAttribute” function with the relevant input … input parameters. (2) The SM-SR checks if a PLMA from Operator2 that authorises the M2M SP to set the Emergency Profile Attribute on Profile B is configured a. If the … rator by calling the “ES3.HandleEmergencyProfileAttributeSetNotification”. Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, … actingact ing as the M2M SP, by calling the “ES2.HandleEmergencyProfileAttributeSetNotification” End Conditions: The Profile B has the Emergency Profile Attribute set. For case 2 the procedure below applies: @startuml skinparam monochrome true skinparam ArrowColor Black hide footbox Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-DP” as DP #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF SP->SR: [1] ES4.SetEmergencyProfileAttribute(EID,ICCID) \non Profile B Request Rnote over SR #FFFFFF [2] Check PLMA for Setting Emergency Profile Attribute from Operator 2 Endrnote SR-->SP: [2.a] Send response indicating authorisation conflict Rnote over SR #FFFFFF [3] Check PLMA for Unsetting Emergency Profile Attribute from Operator 1 Endrnote SR-->SP: [3.a] Send response indicating authorisation conflict SR->EUICC: [4] ES5.SetEmergencyProfileAttribute(ISD -P AID)\non Profile B Rnote over EUICC #FFFFFF [5a] Verify if Profile B has not set Fall -Back Attribute Endrnote EUICC-->SR: [5.a] send error response Rnote over EUICC #FFFFFF [5b] Unset Emergency Profile Attribute on Profile A by Setting Emergency Profile Attribute on Profile B Endrnote EUICC->SR: [6] SetEmergencyProfileAttribute response Rnote over SR #FFFFFF [7] EIS Update(AdditionalProperty) Endrnote SR->OP1: [8] ES4.HandleEmergencyProfileAttribute UnsetNotification\non Profile A Alt [via SM-SR] SR->OP2: [9.a] ES4.HandleEmergencyProfileAttributeSetNotification \non Profile B SR->OP1 Else [via SM-DP] SR->DP: [9.b] ES3.HandleEmergencyProfileAttributeSetNotification \non Profile B DP->OP2: [9.c] ES2.HandleEmergencyProfileAttributeSetNotification \non Profile B end Opt [If if requested by Operator 1] SR->SP: [10] HandleEmergencyProfileAttributeUnsetNotification of Profile A End Opt [If if requested by Operator 2] SR->SP: [11] HandleEmergencyProfileAttributeSetNotification of Profile B end @enduml Figure 326-B: Emergency Profile Attribute Management by M2M SP (case 2: change of Emergency Profile) Start Conditions: a. Profile A with Emergency Profile Attri … M SP requests setting of the Emergency Profile Attribute on Profile B to the SM- SR by calling the “ES4.SetEmergencyProfileAttribute” function with the relevant … input input parameters. (2) The SM-SR checks if a PLMA from Operator2 that authorises the M2M SP to set the Emergency Profile Attribute on Profile B is configured. a… …

3.27 Fall-Back Attribute Managementmodified

This procedure contains the steps needed to change the Fall-Back Attribute from one Profile to another. The Operator1 needs to grant PLMA for Operator2 in order to authorise to set the Fall-BackFall -Back Attribute in Operator1 owned Profile, as a consequence, Operator2 owned Profile has the Fall- Back Attribute un-set (see GSMA Remote Provisioning Architecture f … e Fall-Back Attribute is only un-set as the consequence of setting the Fall-Back Attribute on another Profile. The sequence flow below describes the procedure. … @startuml skinparam monochrome true skinparam ArrowColor Black hide footbox Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF OP2->SR: [1] ES4.SetFallBackAttribute(EID, ICCID) \non Profile B Request Rnote over SR #FFFFFF [2] Check PLMA for un-setting Fall-Back Attribute from Operator1 Endrnote SR-->OP2: [2.a] Return response indicating the PLMA conflict SR->EUICC: [3] ES5.SetFallBackAttribute on Profile B request Rnote over EUICC #FFFFFF [4] Unset Fall-Back Attribute on Profile A by Setting Fall-Back Attribute on Profile B Endrnote EUICC->SR: [5] ES5.SetFallBackAttribute response (euiccResponseData) Rnote over SR #FFFFFF [6] Update EIS Endrnote SR->OP2: [7] ES4.SetFallBackAttribute response SR->OP1: [8] Cond: ES4.HandleProfileFallBackAttributeUnSe tNotification Report SR->SP: [9] Cond: HandleProfileFallBackAttributeUnsetNotification of Profile A SR->OP2: [10] Cond: ES4.HandleProfileFallBackAttributeSetNotification Report SR->SP: [11] Cond: HandleProfileFallBackAttributeSetNotification of Profile B @enduml Figure 327: Fall Back Attribute Management Procedure Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for Embedded … “ES2.HandleProfileFallBackAttributeUnsetNotification”. (9) Unless Operator2 has set an ONC to not receive those notifications, the SM-SR sends the response back … to to Operator2 (10) The SM-SR SHALL send the "ES4.HandleProfileFallBackAttributeUnsetNotification" to an M2M SP, if authorised by Operator1 owning the Profile A.… …

3.28 Fall-Back Attribute Management via SM-DPmodified

This procedure contains the steps needed to change the Fall-Back Attribute from one Profile to another via SM-DP (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.19). @startuml skinparam monochrome true skinparam ArrowColor Black hide footbox Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-DP” as DP #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF OP2->DP: [1] ES2.SetFallBackAttribute on Profile B\nRequest (SMSR-ID, EID, ICCID) Rnote over DP #FFFFFF [2] Identify SM-SR Endrnote DP->SR: [3] ES3.SetFallBackAttibute on Profile B Request (EID, ICCID) Rnote over SR #FFFFFF [4] Check PLMA for unsetting Fall-Back Endrnote SR-->DP: [4.a] Return response indicating PLMA conflict DP->OP2: [4.b] Return response indicating PLMA conflict SR->EUICC: [5] ES5.SetFallBackAttribute on Profile B request Rnote over EUICC #FFFFFF [6] Unset Fall-Back Attribute on Profile A by Setting Fall-Back Attribute on Profile B Endrnote EUICC->SR: [7] ES5.SetFallBackAttribute response (euiccResponseData) Rnote over SR #FFFFFF [8] Update EIS Endrnote SRDP: [9] ES3.SetFallBackAttibute response DPOP2: [10] ES2.SetFallBackAttribute response SR->OP1: [11] Cond: ES4.HandleProfileFallBackAttributeUnsetNotification Rep ort SR->SP: [12] Cond: ES4.HandleProfileFallBackAttributeUnsetNotification of Profile A SR->DP: [13] Cond: ES4.HandleProfileFallBackAttributeSetNotification \nof Profile B SR->SP: [14] Cond: ES4.HandleProfileFallBackAttributeSetNotification of Profile B @enduml Figure 328: Fall-Back AtributeAttribute Management via SM-DPSM -DP Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for Embedded UICC [1]. Procedure: (1) The Operator2 owning Profile … ponse to the SM-DP. (10) The SM-DP SHALL send the “ES2.SetFallBackAttibute” response to the Operator2, informing that the Profile B has the Fall-Back Attribute … set..set. (11) Unless Operator1 has set an ONC to not receive those notifications, the SM-SR SHALL call the “ES4.HandleProfileFallBackAttributeUnsetNotification” functio… …

3.29 Fall-Back Attribute Management via M2M SPmodified

… Fall-Back Attribute on its Profile. Such authorisations are granted via PLMA (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.20). … @startuml skinparam monochrome true skinparam ArrowColor Black hide footbox Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF SP->SR: [1] ES4.SetFallBackAttribute (EID, ICCID) on Profile B Request Rnote over SR #FFFFFF [2] Check PLMA for Setting Fall-Back Attribute from Operator 2 Endrnote SR-->SP: [2.a] Send response indicating authorisation conflict Rnote over SR #FFFFFF [3] Check PLMA for Unsetting Fall-Back Attribute from Operator 1 Endrnote SR-->SP: [3.a] Send response indicating authorisation conflict SR->EUICC: [4] ES5.SetFallBackAttribute on Profile B request Rnote over EUICC #FFFFFF [5] Unset Fall-Back Attribute on Profile A by Setting Fall-Back Attribute on Profile B Endrnote EUICC->SR: [6] ES5.SetFallBackAttribute response (euiccResponseData) Rnote over SR #FFFFFF [7] EIS Update Endrnote SR->SP: [8] ES4.SetFallBackAttribute response SR->OP1: [9] Cond: ES4.HandleProfileFallBackAttributeUnsetNotification of Profile A SR->SP: [10] Cond: ES4.HandleProfileFallBackAttributeUnsetNotification of Profile A SR->OP2: [11] Cond: ES4.HandleProfileFallBackAttributeSetNotification of Profile B SR->SP: [12] Cond: ES4.HandleProfileFallBackAttributeSetNotification of Profile B @enduml Figure 329: Fall-Back Attribute Management via M2M SP Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for Embedded… …

3.30 Local Enable for Emergency Profileadded

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 120 skinparam sequenceArrowThickness 1 hide footbox participant “Device” as DEV #FFFFFF participant “eUICC” as eUICC #FFFFFF DEV->>eUICC : (1) ESx.LocalEnableEmergencyProfile Rnote over eUICC #FFFFF (2) Verify that the Emergency Profile exists Endrnote eUICC-->>DEV : Error Rnote over eUICC #FFFFF (3) Verify that the currently Enabled Profile is NOT the Emergency Profile Endrnote eUICC-->>DEV : Error group Profile switch Rnote over eUICC #FFFFF (4) Enable Emergency Profile Endrnote eUICC-->>DEV : (5) Success ||| eUICC->>DEV: (6) REFRESH, (UICC reset) ||| Rnote over DEV, eUICC #FFFFFF (7) Network attachment with the Emergency Profile Endrnote end @enduml Figure 330: Local Enable of Emergency Profile Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Procedure: (1) The Device SHALL call the “ESx.LocalEnableEmergencyProfile” function. (2) The eUICC SHALL verify that the Emergency Profile (Profile with the Emergency Profile Attribute set) exists on this eUICC. If the condition to be verified is not satisfied, the eUICC SHALL return a response indicating the failure, and the procedure SHALL end. (3) The eUICC SHALL verify that the current Enabled Profile is NOT already the Emergency Profile. If the condition to be verified is not satisfied, the eUICC SHALL return a response indicating that the Emergency Profile is already Enabled, and the procedure SHALL end. (4) The eUICC SHALL NOT enforce POL1 of the currently Enabled Profile, and SHALL disable the currently Enabled Profile and enable the Emergency Profile. NOTE: Profile change includes a change of the IMSI that is used to attach to the network. As indicated in 3GPP TS 31.102 [52], such a change requires special caution and should always be accompanied by a REFRESH command to avoid inconsistent information being read by the terminal. So while the Profile is marked as enabled in this step, it MAY actually become effective after the terminal executes the REFRESH command. (5) The eUICC SHALL return the successful execution status of the “ ESx. LocalEnableEmergencyProfile” command to the Device. (6) The eUICC SHALL send a REFRESH proactive command in UICC reset mode to the Device. This will trigger the execution of a network attach procedure. (7) The Device SHALL perform a network attach procedure with the newly enabled Profile. NOTE: Whether the Emergency Profile provides connectivity to a test network or not, the eUICC will not attempt to enable automatically the previously Enabled Profile. This is in contrast to the remote enable procedure s (for example in section 3.2.2).

3.31 Local Disable for Emergency Profileadded

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 100 skinparam sequenceArrowThickness 1 hide footbox participant “Device” as DEV #FFFFFF participant “eUICC” as ISDR #FFFFFF DEV->>ISDR : (1) ESx.LocalDisableEmergencyProfile Rnote over ISDR #FFFFF (2) Verify that the currently Enabled profile is the Emergency Profile Endrnote ISDR-->>DEV : Error group Profile switch Rnote over ISDR #FFFFF (3) Disable Emergency Profile and enable previously Enabled Profile Endrnote ISDR-->>DEV : (4) Sucess ||| ISDR->>DEV: (5) REFRESH, (UICC reset) ||| Rnote over DEV, ISDR #FFFFFF (6) Network attachment with the Enabled Profile Endrnote End @enduml Figure 331: Local Disable of Emergency Profile Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]. Procedure: (1) The Device SHALL call the “ESx.LocalDisableEmergencyProfile” function. (2) The eUICC SHALL verify that the currently Enabled Profile is the Emergency Profile (Emergency Profile attribute set). If the condition to be verified is not satisfied, the eUICC SHALL return a response indicating that the Emergency Profile is not Enabled, and the procedure SHALL end. (3) The eUICC SHALL NOT enforce POL1 of the Enabled Emergency Profile, and SHALL disable the Emergency Profile and enable the previously Enabled Profile. NOTE: The previously Enabled Profile is the Profile that was Enabled, before the Emergency Profile was enabled by the “ESx.LocalEnableEmergencyProfile” command. (4) The eUICC SHALL return the successful execution status of the “ESx.LocalDisableEmergencyProfile” command to the Device. (5) The eUICC SHALL send a REFRESH proactive command in UICC reset mode to the Device. This will trigger the execution of a network attach procedure. (6) The eUICC and the Device SHALL perform a network attach procedure with the newly Enabled Profile. Dependent on the configuration of the eUICC, the eUICC MAY send a Notification about the Profile change after Emergency Profile disabling to the SM-SR.

4 eUICC Interface Descriptionsmodified

…wing:  ES5, interface between the SM-SR and the eUICC.  ES6, interface between the Operator and the eUICC  ES8, interface between the SM-DP and the eUICC.  … ESX,ESx, interface between the Device and the eUICC. The following table presents the normative list of all the functions that are defined in this section. Request-response functions: Function Interface Function group Functions providerprov ider entity ES5 Platform Management CreateISDP ISD-R EnableProfile DisableProfile DeleteProfile Platform Management eUICCCapabilityAudit MasterDelete ES5 SetFallbackAttribute ISD-R SetEmergencyProfileAttribute EstablishISDRKeySet eUICC Management FinaliseISDRhandover UpdateSMSRAddressingParameters UpdatePOL1byMNO ES6 Profile Management MNO … e LocalDisableTestProfile Table 5:: Request Response Functions Notification handler functions: Function Interface Function group Notification handler functions … providerprov ider Role HandleDefaultNotification ES5 Platform Management SM-SR HandleNotificationConfirmation Table 6: Notification Handler Functions

4.1.1.1 ISD-P Creationmodified

…ribe the installation command and the specific parameters within the data field: Code Value Meaning CLA ‘80’ See GlobalPlatform Card Specification section 11.1 … Code Value Meaning INS ‘E6’ INSTALL P1 ‘0C’ See GlobalPlatform Card Specification [6] section 11.5.2.1 P2 ‘00’ See GlobalPlatform Card Specification [6] section 11.5.2.2 Code Value Meaning Lc ‘xx’ Data Field Length Data ‘xxxx…’ See GlobalPlatform Card Specification [6] section 11.5.2.3 Le ‘00’ Table 7: INSTALL Command Message Reference Control Pa… …

4.1.1.2 Profile Enablingmodified

…d the POL1 of the previously enabled profile does not allow its own disabling, or contains the rule “Profile deletion is mandatory when its state is changed to … disabled”,disabled ”, terminate the command with an error status word  Disable the currently Enabled Profile and Enable the target Profile  Send the REFRESH command in “UICC Reset” … ue Meaning CLA ‘80’ INS ‘E2’ STORE DATA P1 ‘88’ Reference Control Parameter P1 0 P2 ‘00’ Block Number (Not used for Enable command) Lc ‘XX’ Length of data field … Code Value Meaning Data ‘XX’ Application Data and MAC (if present) Le Not present Table 11: STORE DATA COMMAND Message Parameter P1 is coded according to the following table: b8 … …

4.1.1.4 Profile Deletionmodified

…rofile with the Fall-Back Attribute set  The target Profile SHALL NOT be the Test Profile Function flow Upon reception of the DELETE command, the eUICC SHALL: … Verify If the Profile is in Disabled state:  Verify that POL1 of the target Profile allows its deletion. This includes, if the target Profile has been Disabled by the activation of the Fall-Back Mechanism describ … t Profile is not in the Enabled state  If any of these verifications fail, terminate the command with an error status word  Delete the ISD-P with its Profile. … NOTE: An incomplete Profile (i.e. the ISD-P is still in state SELECTABLE or PERSONALIZED) can always be deleted. Command Description: DELETE COMMAND This function is realised through the GlobalPlatform DELETE command as defined in GlobalPlatform Card Specification Amendme… …

4.1.1.8 ISD-R Key Set Establishmentmodified

…n of the Root certificate) other TLVs MAY be present ‘7F49’ Var. Public Key – details see tables below M ‘5F37’ Var. Signature M Table 39: Data Fields for Send … SM-SRSM -SR Certificate for ISD-R Key Establishment The following TLV-encoded data are signed off-card with SK.CI.ECDSA to generate the content of tag ‘5F37’ (signature), a … onse Message: The STORE DATA response SHALL contain the following data: Tag Length Data Element '85' Variable Random Challenge Table 41: Response Data for Send … SM-SRSM -SR Certificate Processing State Returned in the Response Message: As defined in GlobalPlatform Card Specification [6] section 11.11.3.2. Second STORE DATA commandC … ation Amendment E: Security Upgrade for Card Content Management [11] section 4.8.1) In the context of the ISD-R keyset establishment process, this option SHALL … alwaysalw ays be used by the SM- SR (see NOTE 1). Include DR in key derivation process (as defined in GlobalPlatform Card – – – – – – X – (as defined in GlobalPlatform Card Specification Amendment E: Security Upgrade for Card Content Management [11] section 4.8.1) Include Host and Card ID in key derivation process – – – – – X – – … …

4.1.1.10 SM-SR Addressing Parameters Updatemodified

…d as specified for the TP-Destination-Address in 3GPP TS 23.040 [39]. BIP open channel parameters for CAT_TP link Description UICC/terminal interface transport … level*level * Data Destination Address comprehension TLV ** Table 54: BIP Open Channel Parameters for CAT_TP Link *As defined in ETSI TS 102 226 [5] in the section “Data for … Description MOC SM-SR FQDN M ’81’ 1-n Full Qualified Domain Name of the SM-SR that will be used in the DNS query. This parameter is coded in ASCII ‘A2’ 0-n DNS … serversserv ers List M List of couple IP/ports allowing to reach DNS servers Tag Length ‘3E' or ‘BE’ 1-n IP address coded as an “Other Adress”Address” as M specified by ETSI TS 102 223 [3] '82' 2 Port number (integer) M A3 0-n Proprietary parameters C Additional parameters that MAY be supported by the eUICC i… …

4.1.1.11 Handle Default Notificationmodified

…re is no single method implemented by all devices to notify the eUICC of network attachment. The eUICC MAY rely on various heuristics to determine that network … attachementattachment is effective. As a worst-case safeguard, the eUICC SHALL attempt to send profile change notifications within a time interval of 10 STATUS events after card res … istinguish a new notification from a retry. In case of a retry, the eUICC SHALL use the same notification sequence number. When a Notification Confirmation has … beenb een successfully received by the SM-SR, the eUICC SHALL increment the sequence number for the next notification. NOTENOTE: : Depending on the eUICC implementation, the notification MAY also contain additional TLVs using EUM-specific tags. An SM-SR is not required to record or process … from the requirement described in section 2.4.3.3. Default Notification Protocol Priority A protocol priority order for default notification MAY be defined for … everyeve ry Profile during profile installation or download, and updated using the functions defined in 4.1.2.2 and 4.1.3.4. This protocol priority order specifies which p… …

4.1.2.1 Policy Rules Update by Operatormodified

…rding to GlobalPlatform Card Specification [6], INSTALL [for personalization] command can only be used on applications Associated with a Security Domain. As an … exceptionexceptio n from this rule, the eUICC SHALL allow the MNO-SD to receive this command sequence with data destined to the ISD-P. INSTALL [for personalization] command: Code V … d in response Message: None STORE DATA command: This command is a STORE DATA command, as described in GlobalPlatform Card Specification [6]. Code Value Meaning … CLA ‘80’ CLA INS ‘E2’ STORE DATA P1 ‘88’ Reference Control Parameter P1 0 P2 ‘00’ Block Number (Not used for Enable Lc ‘XX’ Length of data field Lc Data ‘XX’ Application Data and MAC (if present) Le Not present Le Table 68: STORE DATA Command Message Parameter P1 is coded according to the following table: b8 b7 b6 b5 b4 b3 b2 b1 Meaning 1 - - - - - - - Last block - 0 0 -… …

4.1.3.3 Download and Installation of a Profilemodified

…to download a profile onto an eUICC complying with a former version of this specification. The SM-DP can inspect the EIS of the target eUICC to determine which … versionversions of SIMalliance eUICC Profile Package [53] isare supported by the target eUICC. The Profile Package consists of a sequence of PE TLVs. However, SCP03t does not take that PE structure into account, but treats … file protection SHALL performed using either:  Session keys (S-ENC, S-MAC, S-RMAC) resulting from the key agreement with eUICC (INITIALIZE UPDATE and EXTERNAL … AUTHENTICATEAUTHENTICATE). ).  Or random keys per Profile (denoted PPK-ENC, PPK-MAC, PPK-RMAC in this document), generated by the SM-DP. Command 85 Command 84 Command 86 (generates S-ENC, S … sponse 86 (S-ENC, S-RMAC) Figure 4133-A: Key usage for the protection of the SCP03t command and responses when using initial session keys Command 85 Command 84 … (generates S-ENC, Command 87 Command 86 (generates S-ENC, S-MAC, but they (S-ENC, S-MAC) (PPK-ENC, PPK-MAC) are not used yet) Response 84 Response 85 Response 87 Response 86 (PPK-ENC, PPK-RMAC) Figure 4133-B: Key usage … ownload process. They SHALL be deleted on the eUICC at the latest at the end of the process. In case of failure during the first attempt to download a Profile, … theth e PPK-RMAC SHALL NOT be reused again. The SM-DP SHALL regenerate a new PPK-RMAC for every retry. Replace session key command TLV This command is used, during the … rent for each download attempt of the same Profile. The following data SHALL be encapsulated in a BER-TLV with tag '87': Tag Length Value description MOC 80 16 … - 32 Initial macMAC chaining M value 81 16 - 32 PPK-ENC M 82 16 - 32 PPK-MAC M 83 16 - 32 PPK-RMAC M Table 4133-C: Replace Session Key Command TLV When using random keys for profi … file SHALL be aborted.  Replace the current session keys with the new set of keys. Once the command is successfully executed, the eUICC SHALL use this new set … ofo f keys for decryption and MAC verification of subsequent SCP03t blocks of data, and encryption and MACing of responses. The key type of the new set of keys is th… …

4.1.4.1 Local Enable for Emergency Profilemodified

… Emergency Profile Attribute set is realised by using the ENVELOPE command with a dedicated Tag. Data Field of ENVELOPE Tag Length Value Description MOC ‘E4’ 1 … 00;00: Local Enable of Emergency Profile M 01: Local Disable of Emergency Profile 02: Local Enable of Test Profile 03: Local Disable of Test Profile 04-FF: RFU Table 4141: Data Field for Envelope containing Local Enable and Local Disable Data Field Returned in the Response Message: The structure of the response data is defined below: -- ASN1START ResultCode ::= [0] INTEGER{ success (0), errorProfileRef (8), -- Emergency/Test Profile does not exists errorAlreadyEnabled (9), -- Emergency/Test Profile is already enabled errorAlreadyDisabled (10), -- Emergency/Test Profile is already disabled errorForbidden (12), -- Transition is forbidden for the Test Profile undefinedError (127) } -- ASN1STOP The following table defines the error codes that are permitted for each command: Response Command (0) (8) (9) (10) (12) LocalEnableEmergencyProfile X X X LocalDisableEmergencyProfile X X Response Command (0) (8) (9) (10) (12) LocalEnableTestProfile X X X X LocalDisableTestProfile X X Table 4141: Error codes allowed for each Local command NOTE In order to support a legacy implementation for the Device, the eUICC MAY support implementation specific commands to trigger the Local Enable and the Local Disable of the Emergency Profile.

4.1.4.2 Local Disable for Emergency Profilemodified

…erequisites:  A Profile with the Emergency Profile Attribute set exists on the eUICC  The Profile with the Emergency Profile Attribute set is enabled Command … and Response Description: See 4.1.4.1

4.1.4.3 Local Enable for Test Profilemodified

…file. Prerequisites:  A Test Profile exists on the eUICC.  The Test Profile is not already enabled.  The Emergency Profile is not currently enabled. Command … and Response Description: See 4.1.4.1

4.1.4.4 Local Disable for Test Profilemodified

…Profile the eUICC MAY send a notification to the SM-SR (see 4.1.1.11).Prerequisites:  A Test Profile exists on the eUICC  The Test Profile is enabled Command … and Response Description: See 4.1.4.1

5 Off-Card Interface Descriptionsmodified

… SR, also used between the two entities fulfilling the Role M2M SP and the Role SM- SR.  ES4A, interface between the two entities fulfilling the Role Operator … anda nd the Role SM- SR, for the specific purpose of configuring M2M SP authorisations and Operator notifications  ES7, interface between the two entities fulfilling t … then all the functions of the corresponding function group SHALL be implemented. The following table presents the normative list of all the functions that are … defineddef ined in this section. Request-response functions: Function Interface Function group Functions providerprov ider Role RegisterEIS ES1 eUICC Management SM-SR UpdateEISAdditionalPropertiesRequest GetEIS AuditEIS DownloadProfile SetFallBackAttribute SetEmergencyProfileAttribute ES2 UpdatePolicyRules SM-DP Profile Management UpdateSubscriptionAddress ES2 GetONC SetONC GetPLMA SetPLMA EnableProfile Platform Management DisableProfile SM-DP DeleteProfile GetEIS AuditEIS CreateISDP SendData ProfileDownloadCompleted SetFallBackAttribute SetEmergencyProfileAttribute ES3 SM-SR Profile Management UpdatePolicyRules ES3 UpdateSubscriptionAddress UpdateConnectivityParameters GetONC SetONC GetPLMA SetPLMA EnableProfile Platform Management DisableProfile SM-SR DeleteISDP GetEIS SetFallBackAttribute SetEmergencyProfileAttribute UpdatePolicyRules Profile Management SM-SR UpdateSubscriptionAddress ES4 AuditEIS ES4 GetPLMA EnableProfile Platform Management DisableProfile SM-SR DeleteProfile PrepareSMSRChange eUICC Management SM-SR SMSRchange GetONC SetONC ES4A Profile Man… …

5.1.1.1 Simple Typesmodified

…m or -hh:mm) Ex: 2001-12-17T09:30:47Z The EID type is for representing an eUICC-ID. An eUICC-ID is primarily used in the “Embedded UICC Remote Provisioning EID … Hexadecimal string and Management System” to identify an eUICC. See section Hexadecimal string 2.2.2 for EID description. The ICCID type is for representing an ICCID (Integrated Circuit String representation of up to 20 decimal Card IDentifier). The ICCI… …

5.1.1.2 Complex Typesmodified

… Either the MSISDN, the IMSI, or both, SHALL be present. NOTE: Additional address types could be added depending of the deployment mode (for example: SIP-URI). … 5.1.1.2.2 POL2-RULE The POL2-RULE type is defined by the following data structure: Data name Description Type No. MOC Identifies the subject on which the rule has to be a … led” Subject=”PROFILE”, action=”DISABLE”, qualification=”Auto-delete” Any other combination SHALL be treated as not valid regarding this specification release. … 5.1.1.2.3 POL2 The POL2 type is defined by the following data structure: Data name Description Type No. MOC Rules List of Policy Rules defined for a given Profile. POL2-RULE 1..N O Table 101: POL2 Type An empty POL2 SHALL be represented as a POL2 data structure having no rules inside 5.1.1.2.4 PROFILE INFO The PROFILE INFO type is defined by: Data name Description Type No. iccid Identification of the Profile. ICCID 1 The ISD-P-AID of the ISD-P contain … n case the Profile has smdp-id been loaded during issuance of the eUICC, else the value is mandatory. OID 1 Once this information is associated to the Profile, … iti t remains unchanged during the Profile’s life-time. Indicates an Operator specific type of Profile generated by the SM-DPSM -DP or ProfileType String 1 personalised on the eUICC at point of manufacturing (for example 3G_16K) Indicates the amount of cumulative non volatile Memory granted … 1 Table 102: Profile Info NOTE: the presence of each data element is specified in Annex E, according to the function in which the PROFILE INFO is transmitted. … 5.1.1.2.5 KEY-COMPONENT The KEY-COMPONENT type is defined by: Data Description Type No. MOC name Definition of the key type coding. This defines the algorithm associated … ry data. This data SHALL be encrypted with a transport value Hexadecimal string 1 M key agreed between the provider and the requester. Table 103: Key Component … 5.1.1.2.6 KEY The KEY type is defined by: Data name Description Type No. MOC index The Key index as an integer value between 0 and 127 (as defined in integer 1 M GlobalPlatform Card Specifications) kcv The Key Check Value of the key KCV 1 M A simple key is defined using only one Key Component, but it is also KEY- KeyComponents 1..N M possible to define keys with multiple key components (like RSA keys) 1..N M COMPONENT Table 104: Key Type NOTE: A key may be: o a symmetric key. In this case the key will be composed of a single key component. The key value being the sa … The key value in SM-SR being the counter part of the key value in the eUICC (i.e.: the public key at the SM- SR and the private key in the eUICC or vice-versa) … 5.1.1.2.7 CERTIFICATE The CERTIFICATE type is defined by: Data Description Type No. MOC name Indicates the index of the private key, being the private counterpart of the … te SHALL be coded according to GlobalPlatform Hexadecimal value 1 M Card Specification UICC Configuration [7], section 9.2.1 string Table 105: Certificate Type … 5.1.1.2.8 KEYSET The KEY SET type is defined by: Data Description Type No. MOC name The version of the key set (as an integer value). The version version value of a key set SHALL be unique within SD definition. versionInteger 1 M Possible values are from 1 to 127. Integer 1 M Example: ‘48’ stands for a SCP03 version ‘30’ Enumeration{ Generally key set usage (SCP03...) can be fully deduced from the key set version. If version informat … onsidered if missing. keys List of keys contained in the key set KEY 1..128 C(1) A certificate (as defined in GlobalPlatform context) as a counter certificates … CERTIFICATE 1..128 C(1) part of a secret key loaded in a key set. CERTIFICATE 1..128 C(1) Table 106: KeySet Type NOTE: A key set provisioned at SM-SR level may be composed of a set of keys or certificates. A key set SHALL include at least one key or certificate. But for a given index, it MAY exist only one key or one certificate. 5.1.1.2.9 SECURITY-DOMAIN The SECURITY-DOMAIN type is defined by: Data Description Type No. MOC name aid The AID of the security domain AID 1 M The list of TARs allocated … of the Role of the security domain. 1 M ECASD} keysets The list of key sets defined within the security domain KEYSET 1..127 M Table 107: Security Domain Type … 5.1.1.2.10 EUICC-CAPABILITIES The EUICC-CAPABILITIES type allows listing the capabilities supported by the eUICC. The EUICC-CAPABILITIES type is defined by: Data name Desc … L contain the highest supported release number of ETSI TS 102 127 (defining CAT_TP) that is implemented by the eUICC. CAT_TP- Conditional to the support of the … CAT_TP-Support.CAT_TP. Version 1 C Version In case of support, the supported version SHALL be at least the minimum version mandated by the present specification. If RAM over HTTP acc … the highest supported release number of GlobalPlatform Amendment B (defining RAM over HTTP) that is implemented by the eUICC. Conditional to the support of the … HTTP-Support.HTTP. HTTP-Version Version 1 C In case of support, the supported version SHALL be at least the minimum version mandated by the present specification. SHALL contain t … evant specifications referenced in this specification. Remote- Note 1: If the document version has less than three digits, one or more extra “.0” provisioning- … Version 1 M SHALL be appended to obtain a value that conforms to the type “Version” defined Version 1 M version in Table 98. For example a value of “3.1.0” denotes that the eUICC is compliant with version 3.1 of SGP.02 Note 2: For backwards-compatibility reasons, if an EIS contains a value “1.1.0” for this field, the off-card entity SHALL assume that the eUICC is compliantcom pliant with version 3.0 of SGP.02 or earlier. Table 108: eUICC Capabilities Type NoteNote: : Additional eUICC capabilities MAY be advertisedindicated in the EIS’s AdditionalProperties (cf section A.3.5.1).A.3.5). This specification defines the following combinations of key:values, but other capabilities MAY be supported by EUMs: Key Value MOC “gsma.ESIM.DNSResolverClientSupport” “true” or “false” O (an absent key/value pair having the default meaning of “false”) “gsma.ESIM.OSUpdateSupported” “true” or “false” O (an absent key/value pair having the default meaning of “false”) “gsma.ESIM.updatedPlatformVersion” an EUM specific string identifying the version of the OS after the update C “gsma.ESIM.JavaCardVersionSupported” This field SHALL be present if the eUICC is compliant with version 4.1 or C later. If the eUICC supports Java Card TM [66], the value SHALL be a string formatted as type VERSION, indicating the version of Java Card TM supported. If the eUICC does not support Java Card TM [66], the value SHALL be the string “none”. Note 1: this field may be present if the eUICC is compliant with an earlier version. Note 2: See section 2.2.7 for the requirement on the minimal version. Note 3: this field is new in version 4.1 of this specification, so servers compliant with former versions may not interpret it; however, the previous versions already mandate the SM-SR to carry the information e.g. in GetEIS or in ES7.HandoverEUICC. “gsma.ESIM.ProfilePackageVersions” This field indicates the list of major versions including the associated M highest minor version number of the SIMalliance eUICC Profile Package: Interoperable Format Technical Specification [53] supported by the eUICC. The list shall be provided in a single string, where each version is a string formatted as type VERSION, and the different versions, if more than one, are separated by a semi -colon. “gsma.ESIM.UICCCapability” This field indicates the UICC Capabilities supported by this eUICC. The M SM-DP MAY use those fields to select or tailor the proper Profile Package to install on this eUICC. The value of this field SHALL be the hexadecimal representation of the value part of the DER encoded UICCCapability data object defined in figure 511210-A (i.e., without tag and length fields). Table 109: AdditionalProperties denoting additional eUICC capabilities The UICC Capabilities to be indicated in the EIS in this version of the specification are defined as follows: -- ASN1START -- Definition of UICCCapability UICCCapability ::= BIT STRING { /* Sequence is derived from ServicesList[] defined in SIMalliance PEDefinitions*/ contactlessSupport(0), -- Contactless (SWP, HCI and associated APIs) usimSupport(1), -- USIM as defined by 3GPP isimSupport(2), -- ISIM as defined by 3GPP csimSupport(3), -- CSIM as defined by 3GPP2 akaMilenage(4), -- Milenage as AKA algorithm akaCave(5), -- CAVE as authentication algorithm akaTuak128(6), -- TUAK as AKA algorithm with 128 bit key length akaTuak256(7), -- TUAK as AKA algorithm with 256 bit key length rfu1(8), -- reserved for further algorithms rfu2(9), -- reserved for further algorithms gbaAuthenUsim(10), -- GBA authentication in the context of USIM gbaAuthenISim(11), -- GBA authentication in the context of ISIM mbmsAuthenUsim(12), -- MBMS authentication in the context of USIM eapClient(13), -- EAP client javacard(14), -- Javacard support multos(15), -- Multos support multipleUsimSupport(16), -- Multiple USIM applications are supported within the same Profile multipleIsimSupport(17), -- Multiple ISIM applications are supported within the same Profile multipleCsimSupport(18), -- Multiple CSIM applications are supported within the same Profile berTlvFileSupport(19), -- BER TLV files dfLinkSupport(20), -- Linked Directory Files catTp(21), -- Support of CAT TP getIdentity(22), -- Support of the GET IDENTITY command as defined in ETSI TS 102 221 [6] profile-a-x25519(23), -- Support of ECIES Profile A as defined in 3GPP TS 33.501 [XX] profile-b-p256(24), -- Support of ECIES Profile B as defined in 3GPP TS 33.501 [XX] suciCalculatorApi(25) -- Support of the associated API for SUCI derivation as defined in 3GPP 31.130 [YY] } Figure 511210-A: Definition of UICCCapability Future versions of this specification may add more bits to UICCCapability. The SM-SR SHALL transparently handle additional bits. The SM-DP SHALL ignore unknown additional bits. 5.1.1.2.11 AUDIT TRAIL RECORD The AUDIT-TRAIL RECORD type contains the description of a Platform or a Profile Management operation performed by SM-SR or a notification rec … ction Execution Status as defined in section 5.1.5 ExecutionStat status is stored 1 C us The ISD-P-AID of the ISD-P containing the Profile. Not present in case … ISD-P-AID the operation type does not concern a specific ISD-P AID (example: AID ISD-P-AID 1 C EstablishISDRkeyset) The ICCID of the Profile. ICCID String 1 C Not present in case the operation type does not concern a specific ISD- P AID (example: Esta … ng See ETSI TS 102 223 [3], clause 8.81 Hexadecimal MEID 1 C String Table 110: Audit Trail Record Type NOTE: Requester Id OID is empty in case of notification. … 5.1.1.2.12 Command Type Command type coding:  ‘0100’: CreateISDP  ‘0200’: EnableProfile  ‘0300’: DisableProfile  ‘0400’: DeleteProfile  ‘0500’: eUICCCapabilityAudit  … aliseISDRhandover  ‘0A00’: SetEmergencyProfileAttribute  ‘0B00’ to ‘FF00’ RFU NOTE: 1st byte is reserved for Notification Type as defined in section 4.1.1.11 … 5.1.1.2.13 EIS The EIS type is for representing eUICC Information Set. Data name Description Type No. eid Identification of the eUICC. EID 1 See section 5.1.1.1 for type d … and remains unchanged during all the eUICC’s lifetime. The ‘eum-id’ indication, jointly with the ‘platformType’ and ‘version, may especially be useful for the … SM-DPSM -DP to perform the Profile generation and packaging. productionDate The date/time where the eUICC has been manufactured by DATETIME 1 the card vendor. This informat … of information that can be retrieved. This indicates the last date where such operation has been performed, and so indicating the freshness of the information … storedsto red at SM- SR level. This information is optional. If not present, it means that no audit has been performed on the eUICC. smsr-id Identification of the SM-SR currently in charge of eUICC OID 1 management. This information may change during the eUICC’s lifetime.l ifetime. isd-p-loadfile-aid AID of the Executable Load File to be used for instantiation AID 1 of an ISD-P. This information is initially provided by the EUM at registra … signature when this structure is stored or reconstructed:  The data SHALL contain one single Tar element, with the TAR value for the ECASD specified in ECASD … SECURITY-DOMAIN 1 Annex H. SECURITY-DOMAIN 1  If there is more than one Keyset or Certificate per ECASD, they SHALL be ordered according to: o The Keyset 'version' if there is more than one Keyset o The Certificate 'index' if there is more than one Certificate per Keyset Contains the capabilities supported by the eUICC. eUICC-Capabilities EUICC- This information is initially provided by the EUM at EUICC- 1 CAPABILITIES registration time. audit trail History of all the platform and Profile Management AUDIT-TRAIL- 0..N operations or eUICC notifications related to … r extensibility purpose, additional information MAY be carried in the EIS. These information SHALL be specified as AdditionalProperties as specified in section … A.3.5.1.Error! R eference source not found.. This specification defines the following combinations of key:values, but other combinations MAY be supported by EUMs: Key Value “gsma.ESIM.ES1.transportKey” A s … ” ISD-P-AID of the Test Profile, if any. If this value is empty or missing, no Test Profile is present on this eUICC. Table 111-2: Common Additional Properties … 5.1.1.2.14 PLMA The PLMA type is defined by: Data name Description Type No. MOC mno-id Identification of the Operator owner of the Profiles concerned by this PLMA. OID 1 M … the Operator identified by mno-id, and having an empty Profile Type or no Profile Type in the EIS. Identification of the M2M SP that will issue requests to the … SM-SRSM -SR to perform m2m-sp-id authorised operations, or that will receive authorised notifications. m2m-sp-idOID 1 M See section 5.1.1.1 for type description. OID 1 M See sections 5.7.1.1 and 5.7.1.2 for the specification of how the SM-SRSM -SR can identify the requester when it receives ES4 and ES3 requests A list of operation names that identify either requests that the M2M SP will be authorised to send to the SM-SR,SM -SR, or notifications that the M2M SP is authorised to receive from the SM-SR, related to the profiles matching the other criteria in this request. authorisedOperations Any operation not in this list is not or no longer authorised for Profiles matching StringauthorisedOperations 0…N M the other criteria in this PLMA: in this case the M2M SP is not authorised to String 0…N M execute the request, or to receive the notification,n otification, identified by the operation name. An empty list means no operation is allowed, and can be used to remove all authorisations, for Profiles matching the other cri … matches the other criteria in the PLMA The M2M SP is authorised to receive notifications via ES3 or ES4 that any HandleEmergencyProfileAttributeSetNotification … ProifleProfile that matches the other criteria in the PLMA has had its Emergency Profile Attribute set. The M2M SP is authorised to receive notifications via ES3 or ES4 that any HandleEmergencyProfileAttributeUnsetNotification ProifleProfile that matches the other criteriacri teria in the PLMA has had its Emergency Profile Attribute unset. The M2M SP is authorised to receive notifications via ES3 or ES4 that any HandleProfileFallBackAttributeSetNotification Profile that matches the other criteria in the PLMA has had its Fall-BackFall -Back Attribute set. The M2M SP is authorised to receive notifications via ES3 or ES4 that any HandleProfileFallBackAttributeUnsetNotification Profile that matches the other criteria in the PLMA has had its Fall-BackFall -Back Attribute unset. Table 511214-B: List of Operation Eligible to PLMA NOTE: There is no explicit operation UnsetEmergencyProfileAttribute and UnsetFallBackAttribute; the Emergency Profile Attribute or Fall-Back Attribute are only unset as the result of setting it on another Profile. 5.1.1.2.15 ONC The ONC type is defined by: Data name Description Type No. MOC mno-id Identification of the Operator owner of the Profiles concerned by this ONC. OID 1 M Se … is an arbitrary String that is meaningful only in the context of a given Operator (mno-id). String 1 M An empty profileType string means all Profiles for this … mno-idmno -id which have no Profile Type set in the EIS. A list of notifications names that identify which notifications SHALL NOT be sent from the SM-SR to the Profile ownin … e Type, provided in this request. Any notification names in this list is not or no longer requested by the Operator owning the Profile, related to the Profiles … associatedassocia ted with the Profile Type, provided in this request. An empty list means that all notifications are requested by the Operator owning the Profile, related to the Profiles associated with the Profile Type, provided in this request. It can be used to remove alla ll previously configured ONC for this discardedNotifications Profile Type. String 0…N M See table 511215-B beloxbelow for the format of this String. If no Operator Notification Configuration has yet been set in the SM-SRSM -SR for a given Profile Type, then the Operator SHALL receive all notifications for status changes for its own Profiles, associated with this Profile Type, see also … e Profile receives no notifications via ES3 or ES4 HandleProfileDisabledNotification when a Profile, associated with the Profile Type in the ONC, was disabled. … HandleProfileEnabledNotification The Operator ownigowning the Profile receives no notifications via ES3 or ES4 HandleProfileEnabledNotification when a Profile, associated with the Profile Type in the ONC, was enabled. The Operator owning the Profile receives no notifications via ES3 or ES4 HandleProfil… …

5.1.2.1 Validity Periodmodified

…alid. The period starts at the time the function call was received by the function provider and ends a number of seconds later. During this period of time, the … Validity function provider has the responsibility to execute the function. Integer 1 O Period The function provider, on reception of the function call, MAY:  Accept the function call: in that case the function provider accepts the provided validity period  RejectRej ect the function call: if the function provider immediately considers that the validity period is invalid (for example too long or too short) or cannot fulfil the Validity requirements (i.e. cannot start the sequence of operations so that all of the Period operations are completed within the validity period), it SHALL NOT process the Integer 1 O function and SHALL immediately return a Function Execution Status output parameter with a Status field set to 'Failed' and a Subject code and Reason code of the Status Code Data field set to 'Validity'Val idity Period not accepted'. The function provider SHALL also indicate to the function caller an acceptable amount of time into which the request could be fulfilled, b … n that case the function provider SHALL indicate to the function caller the applied validity period value in the Acceptable Validity Period field in the output … header.heade r. The Validity Period SHALL NOT be present for notification functions. Table 112: Validity Period Functions Identifier

5.1.5 Functions Output Headermodified

… of the Acceptable Validity Period field sent in response to the previous function call). Indicates whether the processing has been completed correctly or not. … Function Execution If required, provides information to give details on the ExecutionStatu Function Execution 1 M processing result (status code, status code reason, status s Status message…). The Execution Status type is described below. Table 114: Functions Output Hea … OC name It indicates whether the processing has been completed correctly or not. Value 'Executed-Success' means that the function has been processed correctly. … Enumeration Application output data MAY optionally be part of the function response. Enumeration{Executed- Success, Value 'Executed-WithWarning' means that the function has been processed {Executed- correctly, but that warnings have been generated during this execution. Success,Executed- 1 M Status Application output data MAY optionally be part of the function response in order WithWarning, to provide details on the warnings. Executed-Failed, 1 M Status WithWarning, Value 'Failed' means that the function execution has encountered errors during Expired} its processing. The Status Code Data output structure SHALL give the reason of Failed, error in the processing (values depend on the function and MAY be implementation dependant). Expired} Value 'Expired' means that the validity period of the request has expired before the completion of the function processing. The Status Code Data output structu… …

5.1.6.4 Common Function Status Codemodified

…t described in this specification. The function caller SHALL be ready to handle such situation. Common status code when ‘Function execution status’ is ‘failed’ … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Unknown Function 1.1 1.1 (Identification or The function caller is unknown to the function provider. requester Authentication) Func … icate the name of the concerned parameter. Table 117: Function Execution Status ‘Failed’ Codes Common status code when ‘Function execution status’ is ‘Expired’ … SubjectSubj ect Reason SubjectSubj ect Reason Description code Code Time to The function execution request has expired (end of validity period has been Time to reached). This may be because the server had no time to execute the function or 1.6 Function 5.3 live because the function was requesting a remote communicatio… …

5.2.1 Register EISmodified

…he verification of the EIS signature, an error occurred. 6.1 Verification failed During the consistency review of the EIS data, an error was found (for 8.6 EIS … 2.1 Invalid example free memory is bigger than full memory) 2.1 Invalid Table 120: Register EIS Specific Status Codes

5.3.2 Download a Profilemodified

… the SM-DP SHALL perform the following minimum set of verifications:  The SM-DP SHALL verify it is responsible for downloading and installation of the Profile … The SM-DP MAY provide additional verifications. In case one of these conditions is not satisfied, the SM-DP SHALL refuse the function request and return a ‘Function … with a status code as defined in section 5.1.6.4 or a specific status code as defined in the table below, indicating that the Profile has not been downloaded. … A ‘Function execution status’ indicating ‘Executed_WithWarning’ indicating that the Profile has been downloaded successfully, but the optional Enable has failed or expired. In this case, the Status Code and the eUICCResponseData if available, are the oneseUICCResponseData reportingare the failureones orreported expirationby ofES3.EnableProfile. the Enable. Additional input data: Input data name Description Type No. MOC Identification of the target eUICC. eid EID 1 M See section 5.1.1.1 for type description. smsr-i … ble 125: Download Profile Additional Output Data Specific status codes In addition to the Status Codes returned by ES3.EnableProfile, this function can return: … SubjectSubj ect Reason SubjectSubj ect Reason Description Code code Indicates that the eUICC, identified by this EID, is unknown to the SM- 8.1.1 EID 3.9 Unknown SR.SM-SR. Profile Indicates that the Profile, identified by this iccid is unknown to the SM- 8.2.1 3.9 Unknown ICCID DP.SM-DP. Profile Not Allowed Indicates that the function caller is not allowed to perform this function 8.2.1 1.2 ICCID (Authorisation) function on the target Profile. Profile Indicates that the Profile type identified by this profileType is unknown 8.2.5 3.9 Unknown Type unknown to the SM-DP. Profile Not Allowed Indicates that the function caller is not allowed to perform this function 8.2.5 1.2 Type (Authorisation) function on the ProfileType. Error during execution of the enabling command on the eUICC. The 8.4 ISD-R 4.2 Execution error output data “euiccResponseData contains the exact response coming from the eUICC. Indicates that the SM-SR, identified by this smsr-id, is unknown to or 8.7 SM-SR 3.9 Unknown whose address cannot be resolved by the SM-SRSM -SR Table 126: Download Profile Specific Status Codes

5.3.3 Updating the Policy Rules of a Profilemodified

…ules Additional Input Data Additional output data: None Specific status codes In addition to those returned by ES3.UpdatePolicyRules, this function may return: … SubjectSubj ect Reason SubjectSubj ect Reason Description code code 8.7 SM-SR 3.9 Unknown Indicates that the SM-SR,SM -SR, identified by this smsr-id, is unknown to or whose 8.7 SM-SR 3.9 Unknown address cannot be solved by the SM-DPSM -DP Table 128: Update Policy Specific Status Codes

5.3.5 Profile Enablingmodified

… iccid ICCID 1 M See section 5.1.1.1 for type description. Table 131: Enable Profile Additional Input Data Additional output data:  None Specific status codes … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the eUICC, identified by this EID, is unknown to the SM-SM - 8.1.1 EID 3.9 Unknown SR. Indicates that the profile change procedure couldn’t complete after 8.2 Profile 5.1 Inaccessible enabling the target profile, and the … that the Profile identified by this ICCID is unknown to the SM- 8.2.1 3.9 Unknown ICCID SR. Indicates that the Profile identified by this ICCID is known to the … SM-SRSM -SR Profile 8.2.1 3.4 Invalid destination but installed on another eUICC than the one identified by the function ICCID caller. Profile 8.2.1 3.5 Invalid Transition Indicates that the Profile was already Enabled ICCID Profile Not Allowed Indicates that the function caller is not allowed to perform this function 8.2.1 1.2 ICCID (Authorisation) on the target Profile. 8.2.2 POL1 3.8 Ref … e impacted Profiles doesn’t allow this operation. 8.4 ISD-R 4.2 Execution error Error during execution of the enabling command on the eUICC. Indicates that the … SM-SR,SM -SR, identified by this smsr-id, is unknown to or 8.7 SM-SR 3.9 Unknown whose address cannot be resolved by the function provider. Table 132: Enable Profile Specific Status Codes

5.3.6 Profile Disablingmodified

…cription: This function allows the Operator owner of the Profile to request an SM-DP to disable the Profile in a specified eUICC; eUICC being identified by its … EID..EID. The SM-DP receiving this request SHALL process it according to Profile Disabling via SM- DP procedure described in section 3.5 of this specification. This function may return: A A ‘Function execution status’ with ‘Executed-Success’ indicating that the Profile has been disabled on the eUICC.  A ‘Function execution status’ with ‘Executed-W … . iccid ICCID 1 M See section 5.1.1.1 for type description. Table 133: Disable Profile Additional Input Data Additional output data: None Specific status codes … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose address 8.7 SM-SR 3.9 Unknown cannot be solved by the… …

5.3.7 Delete a Profilemodified

… the SM-SR “ES3.DeleteISDP” as defined in section 5.4.10. Additional input data: Input data name Description Type No. MOC Identification of the targeted eUICC. … eidEid EID 1 M See section 5.1.1.1 for type description. Identification of the Profile to disable. iccid ICCID 1 M See section 5.1.1.1 for type description. smsr-id Identification of the SM-SR currently in charge of eUICC management. smsr-id OID 1 M This information may change during the eUICC’s lifetime. Table 135: Delete Profile Additional Input Data Additional output data: None Specific status codes In addition to those returned by ES3.DeleteISDP, this function may return: SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose 8.7 SM-SR 3.9 Unknown address cannot be resolved by the SM-DPSM -DP Table 136: Delete Profile Specific Status Codes

5.3.10 Notify a SM-SR Changemodified

…he list of EIS data fields that SHALL be included is defined in Annex E. Indication of the date/time when the operation has been performed. completionTimestamp … DATETIME 1 M See section 5.1.1.1 for type description. DATETIME 1 M Table 139: Handle SM-SRSM -SR Change Notification Additional Input Data No output data is expected in response to this notification.

5.3.12 Auditing eUICC Informationmodified

…date information for the Operator’s Profiles. The SM-DP SHALL forward the request to the SM-SR. Additional input data: Input data name Description Type No. MOC … eid Identification of the targeted eUICC.to be audited eid EID 1 M See section 5.1.1.1 for type description. Identification of the SM-SR currently in charge of eUICC management. smsr-id OID 1 M This information may chan … e EIS. The Profiles that do EIS 1 C not belong to the requestor are not included in the response. See section 5.4.2 for considerations on data filtering by the … SM-SR.SM -SR. Table 5312-B: AuditEIS Additional Output Data Specific status codes In addition to the status codes returned by ES3.AuditEIS, this function may return the following status codes: SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose address 8.7 SM-SR 3.9 Unknown cannot be resolved by the SM-DPSM -DP Table 5312-C: AuditEIS Additional Specific Status Codes

5.3.13 Setting Authorisations of M2M -SP to Access Profilesmodified

…Description Type No. MOC plma The specification of the PLMA, and the criteria on which this PLMA applies. PLMA 1 M See section 5.1.1.2.14 for type description. … smsr-id Identification of the SM-SR on which to apply the PLMA. smsr-id OID 1 M Table 5313-A: Set PLMA Additional Input Data Additional output data:  None Specific status codes In addition to the Status codes returned by ES3.SetPLMA, this function can return the following status codes SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose address 8.7 SM-SR 3.9 Unknown cannot be resolved by t… …

5.3.14 Retrieving Authorisations of M2M SP to Access Profilesmodified

…tus code as defined in section 5.1.6.4 or a specific status code as defined in the table below. Additional input data: Input data name Description Type No. MOC … profileType Identification of the Profile type for which PLMAs are searched profileType String 1 C m2m-sp-id Identification of the M2M SP for which PLMAs are searched m2m-sp-id OID 1 C iccid Identification of one specific Profile for which PLMAs are searched ICCID 1 C mno-id Identification of the Operator owning the Profiles to be matched (this input mno-id OID 1 C datum SHALL be present only in case the search criterion is a Profile Type). See section 5.1.1.1 for type description. smsr-id Identification of the SM- … tPLMA Additional Output Data Specific status codes In addition to the Status codes returned by ES3.GetPLMA, this function can return the following Status Codes … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose address 8.7 SM-SR 3.9 Unknown cannot be resolved by t… …

5.3.17 Notify a PLMA Settingmodified

…Profile Type. PLMA 1 M Information about the Profile Type are contained in the PLMA structure. See section 5.1.1.2.14 for type description. completionTimestamp … DATETIME 1 M Indication of the date/time when the operation has been performed. DATETIME 1 M See section 5.1.1.1 for type description. Table 5317: Handle PLMA Setting Notification Additional Input Data

5.3.19 Retrieving Operator Notification Configurationmodified

… after. Additional input data: Input data name Description Type No. MOC profileType Identification of the Profile Type for which the ONC is searched String 1 C … iccid Identification of one specific Profile for which the ONC is searched iccid ICCID 1 C smsr-id Identification of the SM-SR from which to retrieve this ONC. OID 1 M This information may change during the eUICC's lifetime. Table 5319-A: Ge … ations that match the search criterion See section 5.1.1.2.15 for type description. NOTE: onc If no Operator Notification Configuration has yet been set in the … SM-SRSM -SR for a given ONC N M Profile Type, then the output data of this function will list no notification names, as all notifications will be sent for Profiles assigned … Output Data Specific status codes In addition to the list of status codes returned by ES3.GetONC, this function may return the following list of status codes: … SubjectSubj ect Reason SubjectSubj ect Reason Description code code 8.7 SM-SR 3.9 Unknown Indicates that the SM-SR, identified by this smsr-id, is unknown to or cannot be 8.7 SM-SR 3.9 Unknown resolved by the function provider. Table 5319-C: GetONC Specific Status Codes

5.3.20 Setting the Emergency Profile Attributemodified

…er. Additional input data: Input data name Description Type No. MOC Eid Identification of the targeted eUICC. EID 1 M See section 5.1.1.1 for type description. … smsr-id Identification of the SM-SR currently in charge of eUICC management. smsr-id OID 1 M This information may change during the eUICC’s lifetime. Identification of the Profile on which to set the Emergency Profile Attribute. iccid ICCID 1 M …  None Specific status codes In addition to the status codes returned by ES3.setEmergencyProfileAttribute, this function may return the following status codes: … SubjectSubj ect Reason SubjectSubj ect Reason Description Code code 8.7 SM-SR 3.9 Unknown Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose address 8.7 SM-SR 3.9 Unknown cannot be resolved by the function provider. Table 5320-C: Set Emergency Profile Attribute Specific Status Codes

5.3.23 Setting the Fall-Back Attributemodified

…er. Additional input data: Input data name Description Type No. MOC eid Identification of the targeted eUICC. EID 1 M See section 5.1.1.1 for type description. … smsr-id Identification of the SM-SR currently in charge of eUICC management. smsr-id OID 1 M This information may change during the eUICC’s lifetime. Identification of the Profile on which to set the Fall-BackFall -Back Attribute. iccid ICCID 1 M See section 5.1.1.1 for type description. Table 5323-A: Set Fall-Back Attribute Additional Input Data Additional output data:  None Specific status codes In addition to the status codes returned by ES3.SetFallBackAttribute, this function may return the following status codes: SubjectSubj ect Reason SubjectSubj ect Reason Description Code code Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose address 8.7 SM-SR 3.9 Unknown cannot be resolved by t… …

5.4.2 Auditing eUICC Informationmodified

…unction, the SM-SR SHALL update its EIS database upon the basis of this information. The SM-DP SHALL indicate on behalf of which Operator it is requesting this … operation.o peration. If the SM-DP provides a list of ICCID of Profiles to audit, the SM-SR SHALL verify for each profile that the Operator, on behalf of which the SM-DP requests thi … as granted a PLMA allowing the operation “AuditEIS” to the Operator requesting the operation. Additional output data: Output data name Description Type No. MOC … eis The relevant eUICC Information Set of the eUICC EISeis 1 C See section 5.1.1.1 for type description. EIS 1 C The list of EIS data fields that SHALL be included is defined in Annex E. Table 145: Audit EIS Additional Output Data Specific status codes SubjectSubj ect Reason SubjectSubj ect Reason Description Code code Indicates that the eUICC, identified by this EID, is unknown to the 8.1.1 EID 3.9 Unknown function provider Indicates that the Pro… …

5.4.3 Create a New ISD-P in an eUICCmodified

…Profile to download and install. Iccid ICCID 1 M See section 5.1.1.1 for type description. mno-id The identification of the Operator owning the Profile OID 1 M … RequiredMemory Indicates the Cumulative Granted Non Volatile Memoryallocated to the ISD-P to RequiredMemory Integer 1 M contain the Profile. The value is expected in Bytes. Indicates to the function provider that the function caller has something else to do with the t … INSTALL command of the ES5.CreateISDP function. Additional output data: Output data name Description Type No. MOC The AID, allocated by the SM-SR, of the ISD-P … isd-p-aid containing the Profile. The Tar value is included in the C (see isd-p-aid AID 1 C (see AID. See Annex H “Coding of the PIX for ‘Embedded UICC note) Remote Provisioning and Management’ (Normative)”. Contains the detailed error returned by the eUICC … ending of the requested function. Table 148: Create ISD-P Additional Output Data NOTE In case of error or expiration of the function execution, the output data … isd-p-isd -p- aid SHOULD be absent. This output data isd-p-aid was mandatory in version 3.2 and earlier of this specification. For backward-compatibility with such versions, … -SR SHOULD return a value that is clearly not a valid AID (ex: ‘0000000000’) and the SM-DP SHOULD ignore the data, whatever the value is. Specific status codes … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the eUICC, identified by this EID, is unknown to the function 8.1.1 EID 3.9 Unknown provider Indicates that the ICCID is already allocated to another Profile managed by Profile 8.2.1 3.3 Already in use the function provider. ICCID Error during execution of the creation command on the eUICC. In that case, Execution the output data “euiccResponseData contains the exact response coming Execution 8.4 ISD-R 4.2 from the eUICC. error The eUICC has not enough free memory to execute the creation of the new Insufficient ISD-P with this required amount of mem… …

5.4.4 Download a New Profilemodified

…tus code as defined in section 5.1.6.4 or a specific status code as defined in the table below. Additional input data: Input data Description Type No. MOC name … eid Identification of the targeted eUICC. eid EID 1 M See section 5.1.1.1 for type description. Identification of the SD which SHALL process the commands contained in the sd-aid AID 1 M data argument. sd-ai … led on eUICC. The response data is defined in string ES8 depending of the requested function. Table 151: Send Data Additional Output Data Specific status codes … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the eUICC, identified by this EID, is unknown to the 8.1.1 EID 3.9 Unknown function provider ISD-P- Indicates that t … ror occurs at ISD-P 8.3 ISD-P 4.2 Execution error level. ISD-P- Not allowed Indicates that the function caller is not allowed to execute commands 8.3.1 1.2 AID … (Authorisation) in the targeted ISD-P. (Authorisation) Not allowed Indicates that the function caller is not allowed to execute the 8.4 ISD-R 1.2 (Authorisation) requested commands in the ISD-R. Table 152: Send Data Specific Status Codes

5.4.7 Updating eUICC Informationmodified

…tus code as defined in section 5.1.6.4 of a specific status code as defined in the table below. Additional input data: Input data name Description Type No. MOC … eid Identification of the targeted eUICC. eid EID 1 M See section 5.1.1.1 for type description. Identification of the target Profile. iccid ICCID 1 M See section 5.1.1.1 for type description. newSubscriptio … ess 1 M Table 158: Update Subscription Address Additional Input Data Additional output data: This function has no additional output data: Specific status codes … SubjectSubj Reasonect SubjectSubj ect Reason Reason Description code code Indicates that the EIS identified by this EID, is unknown to 8.1.1 EID 1.1 Unknown the function provider Indicates that the Profil… …

5.4.8 Profile Enablingmodified

…ains the detailed error returned by the eUICC in case the function Hexadecimal euiccResponseData execution failed on eUICC. The response data is defined in ES8 … String 1 O String depending of the requested function. Table 161: Enable Profile Additional Output Data Specific status codes SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the eUICC, identified by this EID, is unknown to the function 8.1.1 EID 3.9 Unknown provider. Indicates that the Profile change procedure couldn’t complete after 8.2 Profile 5.1 Inaccessible enabling the target Profile, and the Profile change was rolled-backrolled -back on the eUICC, Profile Indicates that the Profile identified by this ICCID is unknown to the function 8.2.1 3.9 Unknown ICCID provider. Indicates that the Profile identified by this ICCID is known to the function Profile 8.2.1 3.4 Invalid destination provider but installed on another eUICC than the one identified by the ICCID function caller. Profile 8.2.1 3.5 Invalid Transition Indicates that the Profile was already Enabled ICCID Profile Not Allowed Indicates that the function caller is not allowed to perform this function on 8.2.1 1.2 ICCID (Authorisation) the target Profile. 8.2.2 POL… …

5.4.9 Profile Disablingmodified

… M See section 5.1.1.1 for type description. Table 163: Disable Profile Additional Input Data Additional output data: Output data name Description Type No. MOC … euiccResponseData Contains the detailed error returned by the eUICC in case of the Hexadecimal euiccResponseData 1 O function execution failed at the eUICC. String Table 164: Disable Profile Additional Output Data Specific status codes SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the target Profile can’t be disabled. (for example the Profile is the 8.1 eUICC 3.8 Refused only Profile in the eUIC … t the eUICC, identified by this EID, is unknown to the SM-SR. 8.2.1 Profile ICCID 3.9 Unknown Indicates that the Profile identified by this ICCID is unknown to … SM-SR.SM -SR. Invalid Indicates that the Profile identified by this ICCID is known to the SM-SRSM -SR but 8.2.1 Profile ICCID 3.4 destination installed on another eUICC than the one identified by the function caller. Invalid 8.2.1 Profile ICCID 3.5 Indicates that the Profile was already Disabled Transition Not Allowed Indicates that the function caller is not allowed to perform this function on the 8.2.1 Profile ICCID 1.2 (Authorisation) target Profile. Related Object The POL1 of the target Profile has triggered its deletion after disabling it 8.2.2 POL1 3.6 Exists This status code SHALL only be sent along Status =”Executed-WithWarning”=”Executed -WithWarning” 8.2.2 POL1 3.8 Refused The POL1 of the target Profile doesn’t allow this operation. Related Object The POL2 of the target Profile has triggered its deletion aft … thWarning” 8.2.3 POL2 3.8 Refused The POL2 of the target Profile doesn’t allow this operation. No PLMA allows the SM-DP, or the Operator on behalf of which the … SM-DPSM -DP sent 8.2.7 PLMA 3.8 Refused the request, to execute this operation. Error during execution of the disabling command on the eUICC. In that case, the 8.4 ISD-R 4… …

5.4.10 Delete an ISD-Pmodified

…equest is:  Either sent on behalf of an Operator owning the targeted Profile or  Sent on behalf of an Operator that is not the owner of the targeted Profile, … butb ut the Operator owning the targeted Profile has granted a PLMA allowing the operation “DeleteProfile” to the Operator requesting the operation. The SM-SR MAY provi … tus code as defined in section 5.1.6.4 or a specific status code as defined in the table below. Additional input data: Input data name Description Type No. MOC … eid Identification of the targeted eUICC. eid EID 1 M See section 5.1.1.1 for type description. iccid Identification of the Profile to delete. ICCID 1 M See section 5.1.1.1 for type description. Table 166: … e data is defined in ES8 depending of the requested euiccResponseData function. Byte[] 1 O Table 167: Delete ISD-P Additional Output Data Specific status codes … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the eUICC, identified by this EID, is unknown to the 8.1.1 EID 3.9 Unknown function provider. Profile Indicates that … isation) on the target Profile. Profile Indicates that the Profile cannot be deleted because it is the last Profile 8.2.1 3.8 Refused ICCID of the eUICC or the … Fall-BackFall -Back Profile. 8.2.2 POL1 3.8 Refused The POL1 of the Profile doesn’t allow this operation. 8.2.3 POL2 3.8 Refused The POL2 of the Profile doesn’t allow this operation. No PLMA allows the SM-DP, or the Operator on behalf of which the SM-SM - 8.2.7 PLMA 3.8 Refused DP sent the request, to execute this operation. Not Present / The target ISD-P was not found on this eUICC (in this case the Function 8.… …

5.4.11 Update Connectivity Parametersmodified

…ters Update” Hexadecimal connectivityParameters 1 M specified in section 4.1.3.4, containing the connectivityParameters to String associate with the identified … Profile..Profile. Table 169: Update Connectivity Parameters Additional Input Data Additional output data: Output data name Description Type No. MOC Contains the detailed error r … O the Connectivity Parameters in the ISD-P on the targeted eUICC. String Table 170: Update Connectivity Parameters Additional Output Data Specific status codes … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the eUICC, identified by this EID, is unknown to the function 8.1.1 EID 3.9 Unknown provider Profile Indicates that… …

5.4.14 Notify an SM-SR Changemodified

…he eUICC, identified by its EID, that the SM-SR has changed. The notification is sent by the new SM-SR to the SM-DP, which SHALL route this notification to the … Operator..Operator. This notification also conveys the date and time specifying when the operation has been done. This notification is not related to a particular Profile. It is u … Indication of the date/time when the operation has been performed. completionTimestamp DATETIME 1 M See section 5.1.1.1 for type description. Table 174: Handle … SM-SRSM -SR Change Notification Additional Input Data Additional output data: No output data is expected in response to this notification.

5.4.15 Notify a Profile Deletionmodified

Function name: HandleProfileDeletedNotification Related Procedures: Profile Enabling, Profile Enabling via SM-DP, Profile Enabling via M2M SP, Profile Disabling via M2M SP, profile and ISD-P Deletion vavia M2M SP Function group: Platform Management Notification handler/recipient: SM-DP Description: This function SHALL be called to notify that the Profile identifi… …

5.4.16 Setting Authorisations of M2M -SP to Access Profilesmodified

…ng Profiles to grant a PLMA to an M2M SP to perform certain operations, or receive certain notifications, related to a set of Profiles, identified by a Profile … Type..Type. The SM-SR receiving this request SHALL verify that the mno-id in the PLMA matches the mno-id of the Operator on behalf of which the SM-DP declares to send this … applies. PLMA 1 M See section 5.1.1.2.14 for type description. Table 5416-A: SetPLMA Additional Input Data Additional output data:  None Specific status codes … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the Profile Type in the PLMA doesn’t match the Profile Type of any Profile owned by the Operator identified by its mno-id.mno -id. Profile 8.2.5 4.9 Unassigned The SM-SR MAY support this Status Code. If it does support it, the SM- Type SR SHALL record the PLMA anyway, and the Execution Status SHALL be Executed-WithWarning Indicates that the new PLMA has overwritten a former PLMA on the Related Objects 8.2.7 PLMA 3.6 same identifiers. In this case the Execution Status SHALL be Executed- 8.2.7 PLMA 3.6 Exists WithWarning Not Allowed Indicates that the requesting SM-DPSM -DP is not allowed to configure PLMAs 8.2 Profile 1.2 (Authorisation) for the specified Operator Indicates that the M2M SP to grant authorisations to is unknown to or not 8.9 M2M SP 1.1 Unknown connected to this SM-SR Indicates that the Operator, addressed by the mno-idmno -id in the PLMA is 8.10 Operator 1.1 Unknown unknown. Table 5416-B: SetPLMA Specific Status Codes

5.4.17 Retrieving Authorisations of M2M SP to Access Profilesmodified

…ate the result. The caller can then issue another call to getPLMA with more restrictive criteria. NOTE The order of the PLMAs returned in the truncated list is … implementation-dependant.implementation-dependent. This function may return:  A ‘Function execution status’ with ‘Executed- Success’, and additional output data providing the PLMAs.  A ‘Function execution sta … ution status’ indicating ‘Failed’ if the requester was not allowed to request this information. Additional input data: Input data name Description Type No. MOC … profileType Identification of the Profile type for which PLMAs are searched profileType String 1 C m2m-sp-id Identification of the M2M SP for which PLMAs are searched OID 1 C iccid Identification of one specific Profile iccid ICCID 1 C mno-id Identification of the Operator owning the Profiles to be matched (this input OID 1 C datum SHALL be present only in case the search criterion i … As that match the search criteria plma PLMA N M See section 5.1.1.2.14 for type description. Table 5417-B: GetPLMA Additional Output Data Specific status codes … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the Operator on behalf of which the SM-DPSM -DP called the Function Not Allowed function is not the owner of the specified Profile, or doesn’t have a PLMA 1.1 1.2 requester (Authorisation) granted that applies to the targeted Profile or Profile type (including, if the targeted Profile or Profile type is unknown to this SM-SR)SM -SR) Not Allowed Indicates that the requesting SM-DPSM -DP is not allowed to configure PLMAs 8.2 Profile 1.2 (Authorisation) for the specified Operator Indicates that the M2M SP is unknown to or not connected to this SM- 8.9 M2M SP 1.1 Unknown SR Indicates that the Operator, addressed by the mno-idmno -id in the PLMA is 8.10 Operator 1.1 Unknown unknown. Table 5417-C: GetPLMA Specific Status Codes

5.4.21 Setting Operator Configuration to Receive Notificationsmodified

…this Profile Type, see also section 3.21 for details. Additional input data: Input data Description Type No. MOC name onc The specification of the ONC, and the … criterioncriteri on on which this ONC 1 M ONC applies. See section 5.1.1.2.15 for type description. Table 5421-A: SetONC Additional Input Data Additional output data:  None Specific status codes SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the Profile Type in the ONC doesn’t match the Profile Type of any Profile owned by the Operator identified by its mno-id.mno -id. Profile 8.2.5 4.9 Unassigned The SM-SR MAY support this Status Code. If it does support it, the SM- Type SR SHALL record the ONC anyway, and the Execution Status SHALL be Executed-WithWarning Indicates that the new ONC has overwritten a former ONC on the same Related Objects 8.2.8 ONC 3.6 identifiers. In this case the Execution Status SHALL be Executed- 8.2.8 ONC 3.6 Exists WithWarning Indicates that the Operator, addressed by the mno-idmno -id in the ONC, is 8.10 Operator 1.1 Unknown unknown. Not Allowed Indicates that the requesting SM-DP is not allowed to configure ONCs 8.10 Operator 1.2 (Authorisa… …

5.4.22 Retrieving Operator Notification Configurationmodified

…Additional input data: Input data name Description Type No. MOC profileType Identification of the Profile Type for which the ONC applies is searched String 1 C … iccid Identification of one specific Profile for which the ONC applies is searched iccid ICCID 1 C Table 5422-A: GetONC Additional Input Data One and only one of the input data profileType and iccid SHALL be present. Additional output data: Output d … ations that match the search criterion See section 5.1.1.2.15 for type description. NOTE: onc If no Operator Notification Configuration has yet been set in the … SM-SRSM -SR for a given Profile ONC N M Type, then the output data of this function will list no notification names, as all notifications will be sent for Profiles assigne… …

5.4.23 Setting the Emergency Profile Attributemodified

…Contains the detailed error returned by the eUICC in case the function Hexadecimal euiccResponseData execution failed on eUICC. The response data is defined in … String 1 O String ES5.SetEmergencyProfileAttribute. Table 5423-B: Set Emergency Profile Attribute Additional Output Data Specific status codes SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the eUICC, identified by this EID, is unknown to the function 8.1.1 EID 3.9 Unknown provider. Profile Indicates tha… …

5.4.26 Setting the Fall-Back Attributemodified

…’ indicating that the Fall-Back Attribute has been set on the targeted Profile.  A ‘Function execution status’ with ‘Expired’ with a status code as defined in … sectionsec tion 5.1.6.4  A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in section 5.1.6.4 of a specific status code as defined in the table h … tion Type No. MOC eid Identification of the targeted eUICC. EID 1 M See section 5.1.1.1 for type description. Identification of the Profile on which to set the … Fall-BackFall -Back Attribute. iccid ICCID 1 M See section 5.1.1.1 for type description. Table 5426-A: Set Fall-Back Attribute Additional Input Data Additional output data: Output data name Description Type No. MOC Contains the detailed error returned by the eUICC in case the function Hexadecimal euiccResponseData execution failed on eUICC. The response data is defined in Hexadecimal 1 O String ES5.SetFallBackAttribute. Table 5426-B: Set Fall-Back Attribute Additional Output Data Specific status codes SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the eUICC, identified by this EID, is unknown to the function 8.1.1 EID 3.9 Unknown provider. Profile Indicates tha… …

5.5.5 Profile Enablingmodified

…ICC. The response data is defined in ES5 depending of the binary 1 O requested function. Table 185: Enable Profile Additional Output Data Specific status codes … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the eUICC, identified by this EID, is unknown to the function 8.1.1 EID 3.9 Unknown function provider. Indicates that the Profile change procedure couldn’t complete after 8.2 Profile 5.1 Inaccessible enabling the target Profile, and the Profile change was rolled-backrolled -back on the eUICC, Profile Indicates that the Profile identified by this ICCID is unknown to the 8.2.1 3.9 Unknown ICCID function provider. Indicates that the Profile identified by this ICCID is known to the function Profile 8.2.1 3.4 Invalid destination provider but installed on another eUICC than the one identified by the ICCID function caller. Profile 8.2.1 3.5 Invalid Transition Indicates that the Profile was already Enabled ICCID Profile Not Allowed Indicates that the function caller is not allowed to perform this function on 8.2.1 1.2 ICCID (Authorisation) the target Profile. 8.2.2 POL… …

5.5.6 Profile Disablingmodified

…d the only Profile in the eUICC) Indicates that the Profile change procedure couldn’t complete after enabling 8.2 Profile 5.1 Inaccessible the Profile with the … Fall-BackFall -Back Attribute set, and the Profile change was rolled-back on the eUICC, Indicates that the eUICC, identified by this EID, is unknown to the function 8.1.1 EID 3.9 U … own to the function Profile Invalid 8.2.1 3.4 provider but installed on another eUICC than the one identified by the ICCID destination function caller. Profile … Invalid 8.2.1 3.5 Indicates that the Profile was already Disabled ICCID Transition Subject Reason Subject Reason Description code code Profile Not Allowed Indicates that the function caller is not allowed to perform this function on 8.2.1 1.2 ICCID (Authorisation) the target Profile. The POL1 of the target Profile has triggered its deletion after disabling it Related 8.2.2 POL1 3.6 This status code SHALL only be sent along Status =”Executed- Object Exists WithWarning” Subject Reason Subject Reason Description code code 8.2.2 POL1 3.8 Refused The POL1 of the target Profile doesn’t allow this operation. The POL2 of the target Profile has triggered its deletion after disabling it Related 8.2.3 POL2 3.6 This status code SHALL only be sent along Status =”Executed-=”Executed - Object Exists WithWarning” 8.2.3 POL2 3.8 Refused The POL2 of the target Profile doesn’t allow this operation. 8.2.7 PLMA 3.8 Refused No PLMA allows the M2M SP… …

5.5.8 Prepare SM-SR Changemodified

…tus code as defined in section 5.1.6.4 of a specific status code as defined in the table below. Additional input data: Input data name Description Type No. MOC … eid provide the EID of the eUICC eid EID 1 M See section 5.1.1.1 for type description. Identification of the current SM-SR.SM -SR. currentSMSRid OID 1 M See section 5.1.1.1 for type description. Table 193: Prepare SM-SR Change Additional Input Data Table 194: Void Table 195: Void Specific status codes SubjectSubj ect Reason SubjectSubj ect Reason Description Code code Condition Of Use Not Indicates that function provider is not capable of managing the 1.2 Function Provider 3 satisfied eUICC identified by this EID, The new SM-SR doesn’t know or have accesaccess to the current 8.7 SM-SR 1.1 Unknown SM-SR managing this eUICC Already in Use Indicates that the eUICC identified by this EID is already 8.1.1 EID 3.3 (Uniquen… …

5.5.12 Notify a SM-SR Changemodified

…he list of EIS data fields that SHALL be included is defined in Annex E. Indication of the date/time when the operation has been performed. completionTimestamp … DATETIME 1 M See section 5.1.1.1 for type description. DATETIME 1 M Table 201: Handle SM-SRSM -SR Change Notification Additional Input Data Additional output data: No output data is expected in response to this notification.

5.5.14 Notify a Profile Downloadmodified

…eUICC identified by its EID. The SM-SR SHALL inspect the PLMAs that apply to this Profile, and only send this notification to recipients which have a PLMA that … incudesincludes the authorisation to receive this notification. This notification also conveys the date and time specifying when the operation has been done. In case multiple … …

5.5.16 Notify a PLMA Settingmodified

… scope of this specification. Additional input data: Input data name Description Type No. MOC The specification of the PLMA that now applies on a Profile Type. … plma Information about the Profile Type are contained in the PLMA structure PLMA 1 M plma See section 5.1.1.2.14 for type description Indication of the date/time when the operation has been performed. completionTimestamp DATETIME 1 M See section 5.1… …

5.5.17 Retrieving Authorisations of M2M SP to Access Profilesmodified

Function name: GetPLMA Related Procedures: Retrieve Profile Lifecycle Management Authorisation by Operator,Operator , Retrieve Profile Lifecycle Management Authorisation by M2M SP Function group: Profile Management Function Provider: SM-SR Description: This function allows the … ate the result. The caller can then issue another call to getPLMA with more restrictive criteria. NOTE The order of the PLMAs returned in the truncated list is … implementation-dependant.implementation-dependent. This function may return:  A ‘Function execution status’ with ‘Executed- Success’, and additional output data providing the PLMAs.  A ‘Function execution sta … ution status’ indicating ‘Failed’ if the requester was not allowed to request this information. Additional input data: Input data name Description Type No. MOC … profileType Identification of the Profile type for which PLMAs are searched profileType String 1 C m2m-sp-id Identification of the M2M SP for which PLMAs are searched m2m-sp-id OID 1 C iccid Identification of one specific Profile iccid ICCID 1 C mno-id Identification of the Operator owning the Profiles to be matched (this input OID 1 C datum SHALL be present only in case the search criterion i … match the search criterion plma PLMA N M See section 5.1.1.2.14 for type description. Table 5517-B: RetrievePLMA Additional Output Data Specific status codes: … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the Operator or M2M SP which called this function is not Function Not Allowed doesn’t have a PLMA granted that appli … M-SR) Indicates that the M2M SP specified in the search criterion is unknown 8.9 M2M SP 1.1 Unknown to this SM-SR Indicates that the Operator, addressed by the … mno-idmno -id in the PLMA, is 8.10 Operator 1.1 Unknown unknown. Table 5517-C: GetPLMA Specific Status Codes

5.5.18 Setting the Emergency Profile Attributemodified

… Additional Input Data Additional output data: Output data name Description Type No. MOC Contains the detailed error returned by the eUICC in case the function … Hexadecimal euiccResponseData execution failed on eUICC. The response data is defined in Hexadecimal 1 O String ES5.SetEmergencyProfileAttribute. Table 5518-B: Set Emergency Profile Attribute Additional Output Data Specific status codes SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the eUICC, identified by this EID, is unknown to the function 8.1.1 EID 3.9 Unknown provider. Profile Indicates tha… …

5.5.19 Notifying the Emergency Profile Attribute settingmodified

…1.1 for type description. Identification of the Profile that has the Emergency Profile Attribute set. iccid ICCID 1 C See section 5.1.1.1 for type description. … completionTimestamp Indication of the date/time when the operation has been performed. completionTimestamp DATETIME 1 M See section 5.1.1.1 for type description. Table 5519: Handle Emergency Profile Attribute Set Notification Additional Input Data

5.6.1 Create Additional Key Setmodified

…ification of the targeted eUICC. eid EID 1 M See 5.1.1.1 for type description. The Key Version Number of the to-be-created Integer 1 M keyVersionNumber keyset. … O (see initialSequenceCounter The initial value of the Sequence Counter of the O (see initialSequenceCounter Integer 1 keyset note 1) keyset Enumeration {ECC-256, eccKeyLength The length of the Elliptic Curve Cryptography keys. ECC-354, 1 M ECC-512, ECC-521 } Hexadecimal String scenarioParameter Scen … Scenario #3, is set to 1. Additional output data: Output data name Description Type No. MOC A random number generated in the SE for additional derivationRandom … Hexadecimal String 1 C entropy in the key derivation process Hexadecimal String 1 C A Message Authentication Code (MAC) Receipt Hexadecimal String 1 M Receipt Table 204: Create Additional Key Set Additional Output Data NOTE: To avoid subliminal channel attacks, in case the execution Status is Failed or Expired, the SM-SR SHOULD return empty hexadecimal strings for derivation random and Receipt. Specific status codes SubjectSubj ect Reason SubjectSubj ect Reason Description code code 8.1.1 EID 1.1 Unknown Indicates that the EID, is unknown to the function provider Execution Error during the creation of the key s… …

5.6.2 Handover eUICC Informationmodified

…e execution. In particular, if one of the operations fails or expires before having verified the receipt, the function provider SHALL return an error (Function … executionexecutio n status indicating ‘Failed’) This function may return:  A ‘Function execution status’ with ‘Executed- Success’ indicating that the Handover eUICC function has been successfully executed on the SM-SR as requested by the function caller.  A ‘Function execution status’ with ‘Executed-WithWarning’ with a status code defined in the table below, indicating either:  that the eUICC has been successfully transferred to the new SM-SR, but additional configuration has not completed and may need to be done again. The new SM-SR SHALL perform such operations automatically at a later point in time.  or that the eUICC is already managed by the receiving SM-SR (SM-SR2). This may happen when this is the second attempt to perform the SM-SR Change, after the first attempt expired on the old SM-SR (SM-SR1), whereas it was already successful from the point of view of SM-SR2.  A ‘Function execution status’ with ‘Expired’ with a status code as defined in section 5.1.6.4  A ‘Function execution status’ indicating ‘Failed’ with a status … ition to the status codes returned by ES7.AuthenticateSMSR and ES7.CreateAdditionalKeyset, this function may return one of the following specific status codes: … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Function Condition Of Use Indicates that function provider is not capable of managing the 1.2 Function3 Provider 3 Not satisfied eUICC identified by this EID. External 1.1 Unknown One Operator owning a Profile on this eUICC is unknown to or not 1.4 1.1 Unknown Resource reachable from the new SM-SR The function is the second attempt to transfer an eUICC to the same new SM-SR, after a previous attempt had already succeeded from Operation Already the point of view of this SM -SR, whereas it had expired from the 1.6 Function 4.5 point of view of the old SM-SR. Processed In this case the Execution-Status SHALL be ‘Executed- WithWarning’. Indicates that the preparation step hasn’t been performed for the 8.1.1 EID 1.1 Unknown eUICC Error during the creation of the key set at the ISD-R level. In th … output data “euiccResponseData contains the exact response coming from the eUICC. Error during the configuration of ISD-R by SM-SR2, after creating Stopped on … 8.4 ISD-R 4.3 SM-SR2 keyset. This Status Code SHALL only be used when the 8.4 ISD-R 4.3 Warning Function Execution Status’ is “Executed_WithWarning” eUICC Certificate Certificate 8.5.2 Authority 6.3 Certificate Expired ECASD Certificate expired Authority Expired Certificate 8.5.1 ECASD 6.1 Verification Failed The verification of the receipt by SM-SR2SM -SR2 failed. SM-SR2 sends Certification the Certification failure message to SM-SR1. Request Table 207: Handover eUICC Specific Status Codes

5.7.1 Setting M2M -SP Authorisations to Access Profilesmodified

… This function allows the Operator owner of Profiles to grant a PLMA to an M2M SP to perform certain operations, or receive certain notifications, related to a … ceraincertain subset of the Profiles owned by the Operator. The SM-SR receiving this request SHALL verify that the mno-id in the PLMA matches the mno-id of the Operator who … applies. PLMA 1 M See section 5.1.1.2.14 for type description. Table 571-A: Set PLMA Additional Input Data Additional output data:  None Specific status codes … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the M2M SP to grant authorisations to is unknown to or not 8.9 M2M SP 1.1 Unknown connected to this SM-SR Indicates that the Profile Type in the PLMA doesn’t match the Profile Type of any Profile owned by the Operator identified by its mno-id.mno -id. Profile 8.2.5 4.9 Unassigned The SM-SR MAY support this Status Code. If it does support it, the SM-SRSM -SR Type SHALL record the PLMA anyway, and the Execution Status SHALL be Executed-WithWarning Indicates that the new PLMA has overwritten a former PLMA on the same Related 8.2.7 PLMA 3.6 set of Profile/eUICC for the same M2M SP. In this case the Execution Status Objects Exists SHALL be Executed-WithWarning Indicates that the Operator, addressed by the mno-idmno -id in the PLMA, is 8.10 Operator 1.1 Unknown unknown. Table 571-B: SetPLMA Specific Status Codes

5.7.2 Retrieving M2M SP Authorisations to Access Profilesmodified

…e PLMAs. Additional input data: Input data name Description Type No. MOC profileType Identification of the Profile type for which PLMAs are searched String 1 C … m2m-sp-id Identification of the M2M SP for which PLMAs are searched m2m-sp-id OID 1 C iccid Identification of one specific Profile ICCID 1 C mno-id Identification of the Operator owning the Profiles to be matched (this input mno-id OID 1 C datum SHALL be present only in case the search criterion is a Profile Type). See section 5.1.1.1 for type description. Table 572-A: retrievePLMA Additio … at match the search criterion plma See section 5.1.1.2.14 for type description. PLMA N M Table 572-B: retrievePLMA Additional Output Data Specific status codes … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Indicates that the Operator or M2M SP which called this function is not Function Not Allowed doesn’t have a PLMA granted that appli … M-SR) Indicates that the M2M SP specified in the search criterion is unknown 8.9 M2M SP 1.1 Unknown to this SM-SR Indicates that the Operator, addressed by the … mno-idmno -id in the PLMA is 8.10 Operator 1.1 Unknown unknown. Table 572-C: getPLMA Specific Status Codes

5.7.3 Setting Operator Configuration to Receive Notificationsmodified

…NC applies. ONC 1 M See section 5.1.1.2.15 for type description. Table 573-A: SetONC Additional Input Data Additional output data:  None Specific status codes … SubjectSubj ect Reason SubjectSubj ect Reason Description code code Profile Indicates that the Profile Type in the ONC doesn’t match the Profile Type 8.2.5 4.9 Unassigned Type of any Profile owned by the Operator identified by its mno-id.mno -id. Profile 8.2.5 4.9 Unassigned The SM-SR MAY support this Status Code. If it does support it, the SM- Type SR SHALL record the ONC anyway, and the Execution Status SHALL be Executed-WithWarning Indicates that the new ONC has overwritten a former ONC on the same Related Objects 8.2.8 ONC 3.6 identifiers. In this case the Execution Status SHALL be Executed- Exists WithWarning Indicates that the Operator, addressed by the mno-idmno -id in the ONC, is 8.10 Operator 1.1 Unknown unknown. Not Allowed Indicates that the requesting SM-DP is not allowed to configure ONCs 8.10 Operator 1.2 (Authorisa… …

5.7.4 Retrieving Operator Notification Configurationmodified

… after. Additional input data: Input data name Description Type No. MOC profileType Identification of the Profile Type for which the ONC is searched String 1 C … iccid Identification of one specific Profile for which the ONC is searched iccid ICCID 1 C Table 574-A: GetONC Additional Input Data One and only one of the input data profileType and iccid SHALL be present. Additional output data: Output da … ations that match the search criterion See section 5.1.1.2.15 for type description. NOTE: onc If no Operator Notification Configuration has yet been set in the … SM-SRSM -SR for a given ONC N M Profile Type, then the output data of this function will list no notification names, as all notifications will be sent for Profiles assigne… …

A.3.5 Complex Type Mappingmodified

…n the <ds:Signature> element (see section A.10 of this Annex). Additional rps3:AdditionalProperties The <rps3:AdditionalProperties> allows a Properties neutral … representrepresentation of any data based on a "Key:Value pair" representation. Such representation can be used without breaking the XML validation process. Eum Signed rps3:EumSignedI… …

A.7.1 to A.7.13 Voidmodified

Descriptions moved to table and files referenced by section 340A.7397A.7

A.9.1 to A.8.3 Voidmodified

Descriptions moved to table and files referenced by section 340A.9397A.9

B.2.3.2 MEP: Asynchronous Request-Response With Callbackmodified

… requester to Function provider SHALL contain: /wsa:From (REQUIRED) /wsa:To (REQUIRED) /wsa:ReplyTo (OPTIONAL) /wsa:MessageID (REQUIRED) /wsa:Action (REQUIRED) … (0)(7) The Function requester SHALL be able to handle 202 (ACCEPT) HTTP response codes. NOTE: In case the response is 200 (OK) steps (3) and (4) will be skipped if it… …

B.3.2 ES2modified

Function name Binding Information MEP Synchronous Request-Response http://gsma.com/ES2/DataPreparation/ES2- GetEIS /wsa:Action/w sa:Action Request GetEISRequest http://gsma.com/ES2/DataPreparation/ES2- /wsa:Action/w sa:Action GetEISResponse Response MEP Asynchronous Request-Response with CallBack http://gsma.com/ES2/ProfileManagement/ES2- DownloadProfile /wsa:Action/w sa:Action Request DownloadProfile http://gsma.com/ES2/ProfileManagementCallback/ES2- /wsa:Action/w sa:Action DownloadProfile Response MEP Synchronous Request-Response http://gsma.com/ES2/ProfileManagement/ES2- UpdatePolicyRules /wsa:Action/w sa:Action Request UpdatePolicyRulesRequest http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action UpdatePolicyRulesResponse Response MEP Synchronous Request-Response http://gsma.com/ES2/ProfileManagement/ES2- UpdateSubscriptionAddress /wsa:Action/w sa:Action Request UpdateSubscriptionAddressRequest http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action UpdateSubscriptionAddressResponse Response MEP Asynchronous Request-Response with CallBack http://gsma.com/ES2/PlatformManagement/ES2- EnableProfile /wsa:Action/w sa:Action Request EnableProfile http://gsma.com/ES2/PlatformManagementCallback/ES2 /wsa:Action/w sa:Action -EnableProfile Response MEP Asynchronous Request-Response with CallBack DisableProfile http://gsma.com/ES2/PlatformManagement/ES2- /wsa:Action/w sa:Action Request DisableProfile http://gsma.com/ES2/PlatformManagementCallback/ES2 /wsa:Action/w sa:Action -DisableProfile Response MEP Asynchronous Request-Response with CallBack http://gsma.com/ES2/PlatformManagement/ES2- DeleteProfile /wsa:Action/w sa:Action Request DeleteProfile http://gsma.com/ES2/PlatformManagementCallback/ES2 /wsa:Action/w sa:Action -DeleteProfile Response MEP Notification (One-Way) http://gsma.com/ES2/PlatformManagement/ES2- HandleProfileDisabledNotification /wsa:Action/w sa:Action Request HandleProfileDisabledNotification /wsa:Action/w sa:Action (none) Response MEP Notification (One-Way) http://gsma.com/ES2/PlatformManagement/ES2- HandleProfileEnabledNotification /wsa:Action/w sa:Action Request HandleProfileEnabledNotification /wsa:Action/w sa:Action (none) Response MEP Notification (One-Way) HandleSMSRChangeNotification http://gsma.com/ES2/PlatformManagement/ES2- /wsa:Action/w sa:Action Request HandleSMSRChangeNotification /wsa:Action/w sa:Action (none) Response MEP Notification (One-Way) http://gsma.com/ES2/PlatformManagement/ES2- HandleProfileDeletedNotification /wsa:Action/w sa:Action Request HandleProfileDeletedNotification /wsa:Action/w sa:Action (none) Response Asynchronous Request-Response with CallBack MEP http://gsma.com/ES2/ProfileManagement/ES2-AuditEIS /wsa:Action/w sa:Action Request AuditEIS http://gsma.com/ES2/ProfileManagementCallBack/ES2- /wsa:Action/w sa:Action Response AuditEIS Asynchronous Request-Response with CallBack MEP http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action Request SetFallBackAttribute SetFallBackAttribute http://gsma.com/ES2/ProfileManagementCallBack/ES2- /wsa:Action/w sa:Action Response SetFallBackAttribute Notification (One-Way) MEP HandleProfileFallBackAttributeSetNot http://gsma.com/ES2/ProfileManagement/ES2- ification http://gsma.com/ES2/ProfileManagement/ES2-/w /wsa:Actionsa:Action Request HandleProfileFallBackAttributeSetNotification (none) /wsa:Action/w sa:Action Response Notification (One-Way) MEP http://gsma.com/ES2/ProfileManagement/ES2- HandleProfileFallBackAttributeUnset /wsa:Action/w sa:Action Request HandleProfileFallBackAttributeUnsetNotification Notification (none) /wsa:Action/w sa:Action Response Asynchronous Request-Response with CallBack MEP http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action Request SetEmergencyProfileAttribute SetEmergencyProfileAttribute http://gsma.com/ES2/ProfileManagementCallBack/ES2- /wsa:Action/w sa:Action Response SetEmergencyProfileAttribute Notification (One-Way) MEP http://gsma.com/ES2/ProfileManagement/ES2- HandleEmergencyProfileAttributeSet /wsa:Action/w sa:Action Request HandleEmergencyProfileAttributeSetNotification Notification (none) /wsa:Action/w sa:Action Response Notification (One-Way) MEP http://gsma.com/ES2/ProfileManagement/ES2- HandleEmergencyProfileAttributeUns /wsa:Action/w sa:Action Request HandleEmergencyProfileAttributeunSetNotification etNotification (none) /wsa:Action/w sa:Action Response Synchronous Request-Response MEP http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action Request GetONCRequest GetONC http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action Response GetONCResponse Synchronous Request-Response MEP http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action Request SetONCRequest SetONC http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action Response SetONCResponse Synchronous Request-Response MEP http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action Request GetPLMARequest GetPLMA http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action Response GetPLMAResponse Synchronous Request-Response MEP SetPLMA http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action Request SetPLMARequest http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action Response SetPLMAResponse Notification (One-Way) MEP http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action Request HandleProfileDownloadedNotification HandleProfileDownloadedNotification /wsa:Action/w sa:Action (none) Response Notification (One-Way) MEP http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action/w sa:Action Request HandlePLMAChangedNotification HandlePLMAChangedNotification /wsa:Action/w sa:Action (none) Response Notification (One-Way) MEP http://gsma.com/ES2/ProfileManagement/ES2- /wsa:Action Request HandlePolicyRulesUpdatedNotification HandlePolicyRulesUpdatedNotificatio /w sa:Action Request n /wsa:Action/w sa:Action (none) Response Table 228: ES2 Function Binding

B.3.3 ES3modified

Function name Binding Information MEP Synchronous Request-Response http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Request GetEIS GetEISRequest GetEIS http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Response GetEISResponse MEP Asynchronous Request-Response with CallBack /wsa:Action/w sa:Action Request http://gsma.com/ES3/ProfileManagement/ES3-AuditEIS AuditEIS http://gsma.com/ES3/ProfileManagementCallBack/ES3- /wsa:Action/w sa:Action Response AuditEIS MEP Asynchronous Request-Response with CallBack /wsa:Action/w sa:Action Request http://gsma.com/ES3/ProfileManagement/ES3-CreateISDP CreateISDP http://gsma.com/ES3/ProfileManagemenCallBack/ES3-http://gsma.com/ES3/ProfileManagemenCallBack/ES3 /wsa:Action- /w sa:Action Response CreateISDP MEP Asynchronous Request-Response with CallBack /wsa:Action/w sa:Action Request http://gsma.com/ES3/ProfileManagement/ES3-SendData SendData http://gsma.com/ES3/ProfileManagementCallBack/ES3- /wsa:Action/w sa:Action Response SendData MEP Synchronous Request-Response http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Request ProfileDownloadCompleted ProfileDownloadedCompletedRequest http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Response ProfileDownloadedCompletedResponse MEP Synchronous Request-Response http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Request UpdatePolicyRules UpdatePolicyRulesRequest http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Response UpdatePolicyRulesResponse MEP Synchronous Request-Response http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Request UpdateSubscriptionAddress UpdateSubscriptionAddressRequest http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Response UpdateSubscriptionAddressResponse MEP Asynchronous Request-Response with CallBack http://gsma.com/ES3/PlatformManagement/ES3-http://gsma.com/ES3/PlatformManagement/ES3 /wsa:Action- /w sa:Action Request EnableProfile EnableProfile http://gsma.com/ES3/PlatformManagementCallBack/ES3-http://gsma.com/ES3/PlatformManagementCallBack/ES3 /wsa:Action- /w sa:Action Response EnableProfile MEP Asynchronous Request-Response with CallBack http://gsma.com/ES3/PlatformManagement/ES3-http://gsma.com/ES3/PlatformManagement/ES3 /wsa:Action- /w sa:Action Request DisableProfile DisableProfile http://gsma.com/ES3/PlatformManagementCallBack/ES3-http://gsma.com/ES3/PlatformManagementCallBack/ES3 /wsa:Action- /w sa:Action Response DisableProfile MEP Asynchronous Request-Response with CallBack http://gsma.com/ES3/PlatformManagement/ES3-http://gsma.com/ES3/PlatformManagement/ES3 /wsa:Action- /w sa:Action Request DeleteISDP DeleteISDP http://gsma.com/ES3/PlatformManagementCallBack/ES3-http://gsma.com/ES3/PlatformManagementCallBack/ES3 /wsa:Action- /w sa:Action Response DeleteISDP UpdateConnectivityParameters MEP Asynchronous Request-Response with CallBack http://gsma.com/ES3/PlatformManagement/ES3-http://gsma.com/ES3/PlatformManagement/ES3 /wsa:Action- /w sa:Action Request UpdateConnectivityParameters http://gsma.com/ES3/PlatformManagementCallBack/ES3-http://gsma.com/ES3/PlatformManagementCallBack/ES3 /wsa:Action- /w sa:Action Response UpdateConnectivityParameters MEP Notification (One-Way) http://gsma.com/ES3/PlatformManagement/ES3-http://gsma.com/ES3/PlatformManagement/ES3 - HandleProfileDisabledNotification /wsa:Action/w sa:Action Request HandleProfileDisabledNotification /wsa:Action/w sa:Action Response (none) MEP Notification (One-Way) http://gsma.com/ES3/PlatformManagement/ES3-http://gsma.com/ES3/PlatformManagement/ES3 - HandleProfileEnabledNotification /wsa:Action/w sa:Action Request HandleProfileEnabledNotification /wsa:Action/w sa:Action Response (none) MEP Notification (One-Way) http://gsma.com/ES3/PlatformManagement/ES3-http://gsma.com/ES3/PlatformManagement/ES3 - HandleSMSRChangeNotification /wsa:Action/w sa:Action Request HandleSMSRChangeNotification /wsa:Action/w sa:Action Response (none) MEP Notification (One-Way) http://gsma.com/ES3/PlatformManagement/ES3-http://gsma.com/ES3/PlatformManagement/ES3 - HandleProfileDeletedNotification /wsa:Action/w sa:Action Request HandleProfileDeletedNotification /wsa:Action/w sa:Action Response (none) MEP Asynchronous Request-Response with CallBack http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Request SetFallBackAttribute SetFallBackAttribute http://gsma.com/ES3/ProfileManagementCallBack/ES3- /wsa:Action/w sa:Action Response SetFallBackAttribute MEP Notification (One-Way) HandleProfileFallBackAttributeSetNot http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Request ification HandleProfileFallBackAttributeSetNotification /wsa:Action/w sa:Action Response (none) MEP Notification (One-Way) HandleProfileFallBackAttributeUnset http://gsma.com/ES2/ProfileManagement/ES3- /wsa:Action/w sa:Action Request Notification HandleProfileFallBackAttributeUnsetNotification /wsa:Action/w sa:Action Response (none) SetEmergencyProfileAttribute MEP Asynchronous Request-Response with CallBack http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Request SetEmergencyProfileAttribute http://gsma.com/ES3/ProfileManagementCallBack/ES3- /wsa:Action/w sa:Action Response SetEmergencyProfileAttribute MEP Notification (One-Way) HandleEmergencyProfileAttributeSet http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Request Notification HandleEmergencyProfileAttributeSetNotification /wsa:Action/w sa:Action Response (none) MEP Notification (One-Way) HandleEmergencyProfileAttributeUns http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Request etNotification HandleEmergencyProfileAttributeUnsetNotification /wsa:Action/w sa:Action Response (none) MEP Synchronous Request-Response http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Request GetONC GetONCRequest http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Response GetONCResponse MEP Synchronous Request-Response http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Request SetONC SetONCRequest http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Response SetONCResponse MEP Synchronous Request-Response http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Request GetPLMA GetPLMARequest http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Response GetPLMAResponse MEP Synchronous Request-Response http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Request SetPLMA SetPLMARequest http://gsma.com/ES3/ProfileManagement/ES3- /wsa:Action/w sa:Action Response SetPLMAResponse MEP Notification (One-Way) http://gsma.com/ES3/ProfileManagement/ES2- HandleProfileDownloadedNotification /wsa:Action/w sa:Action Request HandleProfileDownloadedNotification /wsa:Action/w sa:Action (none) Response /wsa:Action/w sa:Action (none) Response HandlePLMAChangedNotification MEP Notification (One-Way) http://gsma.com/ES3/ProfileManagement/ES2- /wsa:Action/w sa:Action Request HandlePLMAChangedNotification /wsa:Action/w sa:Action (none) Response HandlePolicyRulesUpdatedNotificatio n MEP Notification (One-Way) http://gsma.com/ES3/ProfileManagement/ES2- /wsa:Action/w sa:Action Request HandlePolicyRulesUpdatedNotification Table 229: ES3 Function Binding

B.3.4 ES4modified

Function name Binding Information MEP Synchronous Request-Response http://gsma.com/ES4/ProfileManagement/ES4- /wsa:Action/w sa:Action Request GetEIS GetEISRequest GetEIS http://gsma.com/ES4/ProfileManagement/ES4- /wsa:Action/w sa:Action Response GetEISResponse MEP Synchronous Request-Response http://gsma.com/ES4/ProfileManagement/ES4- /wsa:Action/w sa:Action Request UpdatePolicyRules UpdatePolicyRulesRequest http://gsma.com/ES4/ProfileManagement/ES4- /wsa:Action/w sa:Action Response UpdatePolicyRulesResponse MEP Synchronous Request-Response http://gsma.com/ES4/ProfileManagement/ES4- /wsa:Action/w sa:Action Request UpdateSubscriptionAddress UpdateSubscriptionAddressRequest http://gsma.com/ES4/ProfileManagement/ES4- /wsa:Action/w sa:Action Response UpdateSubscriptionAddressResponse MEP Asynchronous Request-Response with CallBack /wsa:Action/w sa:Action Request http://gsma.com/ES4/ProfileManagement/ES4-AuditEIS AuditEIS http://gsma.com/ES4/ProfileManagementCallBack/ES4- /wsa:Action/w sa:Action Response AuditEIS EnableProfile MEP Asynchronous Request-Response with CallBack http://gsma.com/ES4/PlatformManagement/ES4-http://gsma.com/ES4/PlatformManagement/ES4 /wsa:Action- /w sa:Action Request EnableProfile http://gsma.com/ES4/PlatformManagementCallBack/ES4-http://gsma.com/ES4/PlatformManagementCallBack/ES4 /wsa:Action- /w sa:Action Response EnableProfile MEP Asynchronous Request-Response with CallBack http://gsma.com/ES4/PlatformManagement/ES4-http://gsma.com/ES4/PlatformManagement/ES4 /wsa:Action- /w sa:Action Request DisableProfile DisableProfile http://gsma.com/ES4/PlatformManagementCallBack/ES4-http://gsma.com/ES4/PlatformManagementCallBack/ES4 /wsa:Action- /w sa:Action Response DisableProfile MEP Asynchronous Request-Response with CallBack http://gsma.com/ES4/PlatformManagement/ES4-http://gsma.com/ES4/PlatformManagement/ES4 /wsa:Action- /w sa:Action Request DeleteProfile DeleteProfile http://gsma.com/ES4/PlatformManagementCallBack/ES4-http://gsma.com/ES4/PlatformManagementCallBack/ES4 /wsa:Action- /w sa:Action Response DeleteProfile MEP Asynchronous Request-Response with CallBack http://gsma.com/ES4/eUICCManagement/ES4- /wsa:Action/w sa:Action Request PrepareSMSRChange PrepareSMSRChange http://gsma.com/ES4/eUICCManagementCallBack/ES4-http://gsma.com/ES4/eUICCManagementCallBack/ES4 /wsa:Action- /w sa:Action Response PrepareSMSRChange MEP Asynchronous Request-Response with CallBack http://gsma.com/ES4/eUICCManagement/ES4- /wsa:Action/w sa:Action Request SMSRChange SMSRChange http://gsma.com/ES4/eUICCManagementCallBack/ES4-http://gsma.com/ES4/eUICCManagementCallBack/ES4 /wsa:Action- /w sa:Action Response SMSRChange MEP Notification (One-Way) http://gsma.com/ES4/PlatformManagement/ES4-http://gsma.com/ES4/PlatformManagement/ES4 - HandleProfileDisabledNotification /wsa:Action/w sa:Action Request HandleProfileDisabledNotification /wsa:Action/w sa:Action Response (none) MEP Notification (One-Way) http://gsma.com/ES4/PlatformManagement/ES4-http://gsma.com/ES4/PlatformManagement/ES4 - HandleProfileEnabledNotification /wsa:Action/w sa:Action Request HandleProfileEnabledNotification /wsa:Action/w sa:Action Response (none) MEP Notification (One-Way) http://gsma.com/ES4/eUICCManagement/ES4- HandleSMSRChangeNotification /wsa:Action/w sa:Action Request HandleSMSRChangeNotification /wsa:Action/w sa:Action Response (none) MEP Notification (One-Way) http://gsma.com/ES4/PlatformManagement/ES4-http://gsma.com/ES4/PlatformManagement/ES4 /wsa:Action- /w sa:Action Request HandleProfileDeletedNotification HandleProfileDeletedNotification /wsa:Action/w sa:Action Response (none) MEP Asynchronous Request-Response with CallBack http://gsma.com/ES4/ProfileManagement/ES4- SetFallBackAttribute /wsa:Action/w sa:Action Request SetFallBackAttribute http://gsma.com/ES4/ProfileManagementCallBack/ES4- /wsa:Action/w sa:Action Response SetFallBackAttribute MEP Notification (One-Way) HandleProfileFallBackAttributeSetNot http://gsma.com/ES4/ProfileManagement/ES4- /wsa:Action/w sa:Action Request ification HandleProfileFallBackAttributeSetNotification /wsa:Action/w sa:Action Response (none) MEP Notification (One-Way) HandleProfileFallBackAttributeUnset http://gsma.com/ES4/ProfileManagement/ES4- /wsa:Action/w sa:Action Request Notification HandleProfileFallBackAttributeUnsetNotification /wsa:Action/w sa:Action Response (none) MEP Asynchronous Request-Response with CallBack http://gsma.com/ES4/ProfileManagement/ES4- SetEmergencyProfileAttribute /wsa:Action/w sa:Action Request SetEmergencyProfileAttribute http://gsma.com/ES4/ProfileManagementCallBack/ES4- /wsa:Action/w sa:Action Response SetEmergencyProfileAttribute HandleEmergencyProfileAttributeSet MEP Notification (One-Way) MEP Notification http://gsma.com/ES4/ProfileManagement/ES4- /wsa:Action/w sa:Action Request HandleEmergencyProfileAttributeSetNotification /wsa:Action/w sa:Action Response (none) MEP Notification (One-Way) HandleEmergencyProfileAttributeUns http://gsma.com/ES4/ProfileManagement/ES4-/w /wsa:Actionsa:Action Request http://gsma.com/ES4/ProfileManagement/ES4- etNotification HandleEmergencyProfileAttributeUnsetNotification /wsa:Action/w sa:Action Response (none) MEP Synchronous Request-Response http://gsma.com/ES4/ProfileManagement/ES4- /wsa:Action/w sa:Action Request GetPLMA GetPLMARequest http://gsma.com/ES4/ProfileManagement/ES4- /wsa:Action/w sa:Action Response GetPLMAResponse MEP Notification (One-Way) http://gsma.com/ES4/ProfileManagement/ES2- /wsa:Action/w sa:Action Request HandleProfileDownloadedNotification HandleProfileDownloadedNotification /wsa:Action/w sa:Action (none) Response MEP Notification (One-Way) http://gsma.com/ES4/ProfileManagement/ES2- /wsa:Action/w sa:Action Request HandlePLMAChangedNotification HandlePLMAChangedNotification /wsa:Action/w sa:Action (none) Response MEP Notification (One-Way) http://gsma.com/ES4/ProfileManagement/ES2- /wsa:ActionHandlePolicyRulesUpdatedNotificatio Request/w HandlePolicyRulesUpdatedNotificatiosa:Action Request HandlePolicyRulesUpdatedNotification n /wsa:Action/w sa:Action (none) Response Table 230: ES4 Functions Binding

E EIS Usage in Functions (Normative)modified

…ory M M M M M Availablememoryforprofiles M M M M M lastAuditDate C C C C smsr-id M M M M M isd-p-loadfile-aid X M M M M M isd-p-module-aid X M M M M M Profiles … M(1)M (1) O(3) O(3bis) M(3)M (3) M Iccid M M M M M isd-p-aid M M M M M mno-id M M M M M fallbackAttribute M M M M M subscriptionAddress M M M M M State M M M M M smdp-id O C C C C ProfileType O … ES3.HandleSMSRChangeNotification ES7.HandoverEUICC ES1.RegisterEIS ES3.AuditEIS ES4.AuditEIS EUM Signed ES2.GetEIS ES3.GetEIS ES4.GetEIS otification Data name … (2) (4)(7) (4) (4)(7) (4bis) ISD-R M(2)M C(4)(7)C M(4)M C(4)(7)C M(4bis)M (2) (2) (4) ECASD X M(2)M M(2)M M M M(4)M eUICC-Capabilities X M M M M M audit trail M signatureAlgorithm X M M M M M signature M(5)M M(5)(5) M(5)M M(5)(5) M(5)M (5) M (5) M (5) AdditionalProperty O C(6) C(6) C(6) C(6) Table 234: EIS Usage NOTE 1: The initial EIS comes with the information of the Profile(s) loaded and installed by the … …

M Examples of ONC Setting (Informative)modified

This annex presents a fictitious scenario where an Operator1Operator 1 identified by its mno-id=6.7.8.9 successively calls one of the SetONC operations, and illustrates how this affects the notifications for the Operator. The table reads with time ascending from top to bottom. Time mno-id profile discarded Consequences Type Notifications t0 - - - No ONC set: Operator1 receives all notifications for all ownedow ned Profiles. t1 6.7.8.9 ABC HandleProfileEnable Operator1 receives “no“ Enable notifications for ownedow ned dNotification Profiles of type ABC. Operator1 receives for ownedow ned Profiles withw ith a Profile type in EIS (apart from ABC) “all” notifications. Operator1 receives for ownedow ned Profiles withoutw ithout a Profile type in EIS “all” notifications. t2 6.7.8.9 ABC HandleProfileEnable Operator1 receives “no“ Enable and “no” Disable dNotification, notifications for ownedow ned Profiles of type ABC. HandleProfileDisable dNotification Operator1 receives for ownedow ned Profiles withw ith a Profile type in dNotification EIS (apart from ABC) “all” notifications. Operator1 receives for ownedow ned Profiles withoutw ithout a Profile type in EIS “all” notifications. t3 6.7.8.9 Empty HandleProfileEnable Operator1 receives “no“ Enable and “no” Disable and dNotification notifications for ownedow ned Profiles of type ABC. Missing are Operator1 receives for ownedow ned Profiles withw ith a Profile type in are treated EIS (apart from ABC) “all” notifications. as the Operator1 receives “no“ Enable notifications for ownedow ned same Profiles withoutw ithout a Profile type in EIS. t4 6.7.8.9 Empty Empty and Missing Operator1 receives “no“ Enable and “no” Disable and are treated as the notifications for ownedow ned Profiles of type ABC. Missing same are Operator1 receives for ownedow ned Profiles withw ith a Profile type in are treated EIS (apart from ABC) “all” notifications. as the Operator1 receives for ownedow ned Profiles withoutw ithout a Profile type same in EIS “all” notifications. Table O1: Example of Applying ONC

N.1 Document Historymodified

… Embedded SIM Alexis Michel, 16/09/201 V2.0 2nd Release of Document Leadership Oberthur 4 Team and Technologies PSMC GSMA Embedded SIM Alexis Michel, 29/05/201 … nd V3.0 3nd3 Release of Document Leadership Oberthur 5 Team and Technologies PSMC GSMA Embedded SIM Alexis Michel, V3.1 12/05/16 Minor Release of Documents Leadership Obert … elease of Document Leadership Duprez, Team and Gemalto PSMC GSMA Embedded SIM Yolanda Sanz V4.0 25/02/19 Major release of Document Leadership / GSMA Team and TG … Version Date Brief Description of Change Approval Editor / Authority Company Jérôme V4.1 05/06/20 Minor release of document ISAG Duprez, Thales

N.2 Other Informationmodified

Type Description Document Owner EmbeddedYolanda SIMSanz, GSMA Editor / Company Jérôme Duprez, GemaltoThales It is our intention to provide a quality product for your use. If you find any errors or omissions, please contact us with your comments. You may notify us at … …

Contents
  1. 1 Introduction
  2. 1.1 Overview
  3. 1.2 Scope
  4. 1.3 Document Purpose
  5. 1.4 Intended Audience
  6. 1.5 Definition of Terms
  7. 1.6 Abbreviations
  8. 1.7 References
  9. 1.8 Conventions
  10. 2 General Parts of the Technical Specification
  11. 2.1 General Architecture
  12. 2.2 eUICC Architecture
  13. 2.2.1 Security Domains
  14. 2.2.2 Identification of eUICC: EID
  15. 2.2.3 Identification of Security Domains: AID and TAR
  16. 2.2.4 Profile Structure
  17. 2.2.5 Secure Channel on Interfaces
  18. 2.2.6 eUICC OS Update
  19. 2.2.7 Java Card™ Support
  20. 2.3 Security Overview
  21. 2.3.1 Certificate Issuer Role
  22. 2.3.2 Certification Chains
  23. 2.3.3 General Consideration on Algorithm and Key Length
  24. 2.4 OTA Communication on ES5 (SM-SR-eUICC)
  25. 2.4.1 General OTA Requirements
  26. 2.4.2 Void
  27. 2.4.3 SMS
  28. 2.4.4 HTTPS
  29. 2.4.5 DNS Resolution
  30. 2.5 Communication on ES8 (SM-DP - eUICC)
  31. 2.6 SM-DP to SM-SR Link Establishment (ES3)
  32. 2.7 OTA Platform Communication on ES6 (Operator-eUICC)
  33. 2.8 Communication on ES1 (EUM - SM-SR)
  34. 2.9 Compliance
  35. 3 Detailed Procedure Specifications
  36. 3.1 Profile Download and Installation
  37. 3.1.1 ISD-P Creation
  38. 3.1.2 Key Establishment with Scenario#3-Mutual Authentication
  39. 3.1.3 Download and Installation of the Profile
  40. 3.1.4 Error Management Sub-Routine
  41. 3.1.5 ISD-P Cleanup Sub-Routine
  42. 3.2 Profile Enabling
  43. 3.2.1 Normal Case
  44. 3.2.2 Connectivity Failure Case
  45. 3.3 Profile Enabling Via SM-DP
  46. 3.3.1 Normal Case
  47. 3.3.2 Connectivity Failure Case
  48. 3.4 Profile Disabling
  49. 3.5 Profile Disabling Via SM-DP
  50. 3.6 Profile and ISD-P Deletion
  51. 3.7 Profile and ISD-P Deletion Via SM-DP
  52. 3.8 SM-SR Change
  53. 3.9 eUICC Registration at SM-SR: Register a New EIS
  54. 3.10 Master Delete Procedure
  55. 3.11 POL2 Update Via SM-DP
  56. 3.12 POL1Update by Operator
  57. 3.13 Connectivity Parameters Update by Operator
  58. 3.14 Connectivity Parameters Update Using SCP03
  59. 3.15 Default Notification Procedure
  60. 3.15.1 Notification Using SMS
  61. 3.15.2 Notification Using HTTPS
  62. 3.16 Fall-Back Activation Procedure
  63. 3.17 Profile Enabling via M2M SP
  64. 3.17.1 Normal Case
  65. 3.17.2 Connectivity Failure Case
  66. 3.18 Profile Disabling via M2M SP
  67. 3.19 Profile and ISD-P Deletion via M2M SP
  68. 3.20 Profile Lifecycle Management Authorisation (PLMA)
  69. 3.20.1 Set Profile Lifecycle Management Authorisation
  70. 3.20.2 Set Profile Lifecycle Management Authorisation rules via SM-DP
  71. 3.20.3 Retrieve Profile Lifecycle Management Authorisation by Operator
  72. 3.20.4 Retrieve Profile Lifecycle Management Authorisation by Operator via SM-DP
  73. 3.20.5 Retrieve Profile Lifecycle Management Authorisation by M2M SP
  74. 3.21 Operator Notifications Configuration (ONC)
  75. 3.21.1 Set Operator Notifications Configuration
  76. 3.21.2 Set Operator Notifications Configuration via SM-DP
  77. 3.21.3 Retrieve Operator Notifications Configuration
  78. 3.21.4 Retrieve Operator Notifications Configuration via SM-DP
  79. 3.22 Local Enable for Test Profile
  80. 3.23 Local Disable for Test Profile
  81. 3.24 POL2 Update
  82. 3.25 Emergency Profile Attribute Management
  83. 3.26 Emergency Profile Attribute Management via the M2M SP
  84. 3.27 Fall-Back Attribute Management
  85. 3.28 Fall-Back Attribute Management via SM-DP
  86. 3.29 Fall-Back Attribute Management via M2M SP
  87. 3.30 Local Enable for Emergency Profile
  88. 3.31 Local Disable for Emergency Profile
  89. 4 eUICC Interface Descriptions
  90. 4.1 Functions Description
  91. 4.1.1 ES5 (SM-SR–eUICC) Interface Description
  92. 4.1.2 ES6 (Operator-eUICC) Interface Description
  93. 4.1.3 ES8 (SM-DP-eUICC) Interface Description
  94. 4.1.4 ESx (Device - eUICC) Interface Description
  95. 5 Off-Card Interface Descriptions
  96. 5.1 Function Commonalities
  97. 5.1.1 Common Data Types
  98. 5.1.2 Request-Response Function
  99. 5.1.3 Notification Handler function
  100. 5.1.4 Functions Input Header
  101. 5.1.5 Functions Output Header
  102. 5.1.6 Status Code
  103. 5.2 ES1 (EUM – SM-SR) Interface Description
  104. 5.2.1 Register EIS
  105. 5.2.2 Update EIS AdditionalProperties
  106. 5.3 ES2 (Operator – SM-DP) Interface Description
  107. 5.3.1 Getting eUICC Information
  108. 5.3.2 Download a Profile
  109. 5.3.3 Updating the Policy Rules of a Profile
  110. 5.3.4 Updating eUICC Information
  111. 5.3.5 Profile Enabling
  112. 5.3.6 Profile Disabling
  113. 5.3.7 Delete a Profile
  114. 5.3.8 Notify a Profile is Disabled
  115. 5.3.9 Notify a Profile Enabling
  116. 5.3.10 Notify a SM-SR Change
  117. 5.3.11 Notify a Profile Deletion
  118. 5.3.12 Auditing eUICC Information
  119. 5.3.13 Setting Authorisations of M2M -SP to Access Profiles
  120. 5.3.14 Retrieving Authorisations of M2M SP to Access Profiles
  121. 5.3.15 Notify a Profile Download
  122. 5.3.16 Notify the Change of Policy Rules of a Profile
  123. 5.3.17 Notify a PLMA Setting
  124. 5.3.18 Setting Operator Configuration to Receive Notifications
  125. 5.3.19 Retrieving Operator Notification Configuration
  126. 5.3.20 Setting the Emergency Profile Attribute
  127. 5.3.21 Notifying the Emergency Profile Attribute Setting
  128. 5.3.22 Notifying the Emergency Profile Attribute Unsetting
  129. 5.3.23 Setting the Fall-Back Attribute
  130. 5.3.24 Notifying the Fall-Back Attribute is Set
  131. 5.3.25 Notifying the Fall-Back Attribute is Unset
  132. 5.4 ES3 (SM-DP – SM-SR) Interface Description
  133. 5.4.1 Getting eUICC Information
  134. 5.4.2 Auditing eUICC Information
  135. 5.4.3 Create a New ISD-P in an eUICC
  136. 5.4.4 Download a New Profile
  137. 5.4.5 Indicating the Profile Download is Completed
  138. 5.4.6 Updating the Policy Rules of a Profile
  139. 5.4.7 Updating eUICC Information
  140. 5.4.8 Profile Enabling
  141. 5.4.9 Profile Disabling
  142. 5.4.10 Delete an ISD-P
  143. 5.4.11 Update Connectivity Parameters
  144. 5.4.12 Notify a Profile is Disabled
  145. 5.4.13 Notify a Profile Enabling
  146. 5.4.14 Notify an SM-SR Change
  147. 5.4.15 Notify a Profile Deletion
  148. 5.4.16 Setting Authorisations of M2M -SP to Access Profiles
  149. 5.4.17 Retrieving Authorisations of M2M SP to Access Profiles
  150. 5.4.18 Notify a Profile Download
  151. 5.4.19 Notify the Change of Policy Rules of a Profile
  152. 5.4.20 Notify a PLMA Setting
  153. 5.4.21 Setting Operator Configuration to Receive Notifications
  154. 5.4.22 Retrieving Operator Notification Configuration
  155. 5.4.23 Setting the Emergency Profile Attribute
  156. 5.4.24 Notifying the Emergency Profile Attribute Setting
  157. 5.4.25 Notifying the Emergency Profile Attribute Unsetting
  158. 5.4.26 Setting the Fall-Back Attribute
  159. 5.4.27 Notifying the Fall-Back Attribute is Set
  160. 5.4.28 Notifying the Fall-Back Attribute is Unset
  161. 5.5 ES4 (Operator - SM-SR, and M2M SP – SM-SR) Interface Description
  162. 5.5.1 Getting eUICC Information
  163. 5.5.2 Updating the Policy Rules of a Profile
  164. 5.5.3 Updating eUICC Information
  165. 5.5.4 Auditing eUICC Information
  166. 5.5.5 Profile Enabling
  167. 5.5.6 Profile Disabling
  168. 5.5.7 Delete a Profile
  169. 5.5.8 Prepare SM-SR Change
  170. 5.5.9 SM-SR Change
  171. 5.5.10 Notify a Profile is Disabled
  172. 5.5.11 Notify a Profile is Enabled
  173. 5.5.12 Notify a SM-SR Change
  174. 5.5.13 Notify a Profile Deletion
  175. 5.5.14 Notify a Profile Download
  176. 5.5.15 Notify the Change of Policy Rules of a Profile
  177. 5.5.16 Notify a PLMA Setting
  178. 5.5.17 Retrieving Authorisations of M2M SP to Access Profiles
  179. 5.5.18 Setting the Emergency Profile Attribute
  180. 5.5.19 Notifying the Emergency Profile Attribute setting
  181. 5.5.20 Notifying the Emergency Profile Attribute Unsetting
  182. 5.5.21 Setting the Fall-Back Attribute
  183. 5.5.22 Notifying the Fall-Back Attribute is Set
  184. 5.5.23 Notifying the Fall-Back Attribute is Unset
  185. 5.6 ES7 (SM-SR – SM-SR) Interface Description
  186. 5.6.1 Create Additional Key Set
  187. 5.6.2 Handover eUICC Information
  188. 5.6.3 Authenticate SM-SR
  189. 5.7 ES4A (Operator – SM-SR) Interface Description
  190. 5.7.1 Setting M2M -SP Authorisations to Access Profiles
  191. 5.7.2 Retrieving M2M SP Authorisations to Access Profiles
  192. 5.7.3 Setting Operator Configuration to Receive Notifications
  193. 5.7.4 Retrieving Operator Notification Configuration
  194. A Mapping of Functions into Messages (Normative)
  195. A.1 Namespaces and Schema References
  196. A.2 Message: <rps3:RPSMessage>
  197. A.2.1 Void
  198. A.2.2 Void
  199. A.3 Common Types
  200. A.3.1 Common Message Types
  201. A.3.2 Void
  202. A.3.3 Void
  203. A.3.4 Simple Types Mapping
  204. A.3.5 Complex Type Mapping
  205. A.4 The ES1 Interface Functions
  206. A.4.1 Void
  207. A.5 The ES2 Interface Functions
  208. A.5.1 To A.5.12 Void
  209. A.6 The ES3 Interface Functions
  210. A.6.1 to A.615 Void
  211. A.7 The ES4 Interface Functions
  212. A.7.1 to A.7.13 Void
  213. A.8 The ES4A Interface Functions
  214. A.9 The ES7 Interface Functions
  215. A.9.1 to A.8.3 Void
  216. A.10 EUM Signature
  217. B Binding to SOA Environment (Normative)
  218. B.1 General Recommendations
  219. B.2 SOAP Binding
  220. B.2.1 Message Binding
  221. B.2.2 Security
  222. B.2.3 Message Exchange Pattern (MEPs) – HTTPS Binding
  223. B.2.4 Binding Examples
  224. B.2.5 URI – query structure
  225. B.3 Function Binding
  226. B.3.1 ES1
  227. B.3.2 ES2
  228. B.3.3 ES3
  229. B.3.4 ES4
  230. B.3.5 ES7
  231. B.3.6 ES4A
  232. B.4 Web Service Description Language (WSDL)
  233. C Use of GlobalPlatform Privileges (Normative)
  234. D Data Definitions (Normative)
  235. E EIS Usage in Functions (Normative)
  236. F Key Check Values (Normative)
  237. G Device Requirements (Normative)
  238. H Coding of the PIX for ‘Embedded UICC Remote Provisioning and Management’ (Normative)
  239. I List of Identifiers (Normative)
  240. J Verification of EID (Informative)
  241. K Script Chaining implementation (Informative)
  242. L Examples of PLMA Setting (Informative)
  243. M Examples of ONC Setting (Informative)
  244. N Document Management (Informative)
  245. N.1 Document History
  246. N.2 Other Information
SGP.02 Remote Provisioning Architecture for Embedded
                         UICC Technical Specification
                                           Version 4.1
                                         05 June 2020

This is a Non-binding Permanent Reference Document of the GSMA

Security Classification: Non-confidential Access to and distribution of this document is restricted to the persons permitted by the security classification. This document is confidential to the Association and is subject to copyright protection. This document is to be used only for the purposes for which it has been supplied and inf ormation contained in it must not be disclosed or in any other way made available, in whole or in part, to persons other t han those permitted under the security classification without the prior written approval of the Association.

Copyright Notice Copy right © 2020 GSM Association

Disclaimer The GSM Association (“Association”) makes no representation, warranty or undertaking (express or implied) with respect to and does not accept any responsibility for, and hereby disclaims liability for the accuracy or completeness or timeliness of the information contained in this document. The inf ormation contained in this document may be subject to c hange without prior notice.

Antitrust Notice The inf ormation contain herein is in full compliance with the GSM Association’s antitrust compliance policy.

1 Introduction

1.1 Overview

This document provides a technical description of the GSMA’s ‘Remote Provisioning Architecture for Embedded UICC’ [1].

1.2 Scope

This specification provides a technical description of:

   The eUICC Architecture
   The interfaces used within the Remote Provisioning Architecture and
   The security functions used within the Remote Provisioning Architecture

1.3 Document Purpose

The aim of this document is to define a technical solution for the remote provisioning and management of the Embedded UICC (eUICC) in machine-to-machine Devices which are not easily reachable. The adoption of this technical solution will provide the basis for ensuring global interoperability between potentially different Operator deployment scenarios, different makes of network equipment (for example SM-DP, SM-SR) and different makes of eUICC platforms.

1.4 Intended Audience

Technical experts working within Operators, SIM solution providers, machine to machine Device vendors, standards organisations, network infrastructure vendors, Service Providers and other industry bodies.

1.5 Definition of Terms

            Term                                        Description
                              Physical entity (person, company or organisation) that can
                              assume a Role in the functional architecture. It is possible for an
Actor
                              Actor to assume multiple Roles in the same functional
                              architecture.
                              This term refers to a link of an application, an Executable Load
Associated (with) /           File or a security domain to (another) security domain, which
Association                   provides services to the former as defined in GlobalPlatform
                              Card Specification [6] section 7.2.
                              An identifier for a specific GlobalPlatform card and that may be
Card Image Number / Card
                              used by a Card Management System to uniquely identify a card
Identification Number (CIN)
                              within its card base.
                              A periodically (or exigently) issued list, digitally signed by a CA,
                              of identified Certificates that have been revoked prior to their
Certificate Revocation List   expiration dates. The list generally indicates the CRL issuer’s
                              name, the date of issue, the date of the next scheduled CRL
                              issue, the revoked Certificates’ serial numbers, and the specific
                              times and reasons for revocation.
                              A set of data (for example SMSC address) required by the
Connectivity Parameters       eUICC to open a communication channel (for example SMS,
                              HTTPS) on a dedicated network.
                              A paying party, in particular a legally responsible juridical person
Customer
                              or entity.
                              Equipment into which an Embedded UICC and a communication
Device                        module are inserted during assembly. Examples include Utility
                              meter, car and camera.
                              The state of a Profile where all files and applications (for
Disabled (Profile)            example NAA) present in the Profile are not selectable over the
                              eUICC-Terminal interface.
                              Client side on eUICC in charge of initiating the queries to the
DNS Resolver Client
                              DNS server.
                              Server-side component in charge of providing the IP address(s)
DNS Resolver Server
                              of the target server to the DNS Resolver Client
                              An internet protocol for translating domain names (or
Domain Name System
                              hostnames) into IP addresses.
                              A UICC which is not easily accessible or replaceable, is not
Embedded UICC                 intended to be removed or replaced in the Device, and enables
                              the secure changing of Profiles.
                              An Operational Profile with a Profile Attribute allocated,
                              indicating that this Profile is an Emergency Profile.
Emergency Profile             An Emergency Profile complies with regulatory requirements
                              and only provides the capability to make Emergency Calls and
                              receive calls from an Emergency centre (e.g. Public Safety
                              Answering Point)
                              This is an attribute allocated to a Profile which, when set,
Emergency Profile Attribute
                              identifies the Emergency Profile.
                              The state of a Profile when its files and/or applications (for
Enabled (Profile)
                              example, NAA) are selectable over the UICC-Terminal interface.
                              An on-card container of one or more application's executable
Executable Load File
                              code as defined in GlobalPlatform Card Specification [6].
                              The on-card executable code of a single application present
Executable Module             within an Executable Load File as defined in GlobalPlatform
                              Card Specification [6].
                              A certificate issued by the EUM for a specific, individual, eUICC.
eUICC Certificate
                              This certificate can be verified using the EUM Certificate.
                              Supplier of the eUICCs and resident software (for example
eUICC Manufacturer
                              firmware and operating system).
                              Mechanism to correct existing features on an eUICC by the
eUICC OS Update
                              original OS Manufacturer when the eUICC is in the field.
                              A certificate issued to a GSMA accredited EUM which can be
EUM Certificate               used to verify eUICC Certificates.
                              This certificate can be verified using the Root Certificate.
                               This is an attribute of a Profile which, when set, identifies the
                               Profile to be enabled by the Fall-Back Mechanism or by the
Fall-Back Attribute            execution of the Disable Profile function on another Profile. Only
                               one Profile on the eUICC can have the Fall-Back attribute set at
                               a time.
                               eUICC-based mechanism which enables the Profile with Fall-
Fall-Back Mechanism            Back Attribute set when the Enabled Profile loses network
                               connectivity
                               Unique number to identify a Profile in an eUICC.
Integrated Circuit Card ID     Note: the ICCID throughout this specification is used to identify
                               the Profile.
International Mobile           Unique identifier owned and issued by Mobile Network
Subscriber Identity            Operators as defined in ETSI TS 123 003 [31].
                               An identifier for a specific issuer that may be used by an off-card
Issuer Identification Number
                               entity to associate the card with a specific Card Management
(IIN)
                               System.
                               A security domain on the UICC as defined by GlobalPlatform
Issuer Security Domain
                               Card Specification [6].
                               A function of the interface between a Device and an eUICC that
                               provides the capability for a Device to locally disable the
Local Disable
                               Emergency Profile or the Test Profile on the eUICC without
                               involvement of an SM-SR and/or SM-DP.
                               A function of the interface between a Device and an eUICC that
                               provides the capability for a Device to locally enable the
Local Enable
                               Emergency Profile or the Test Profile on the eUICC without
                               involvement of an SM-SR and/or SM-DP.
M2M Service Provider (M2M      A Service Provider relying on an Operator providing the Profiles
SP)                            on the eUICC.
                               An entity providing access capability and communication
Mobile Network Operator        services to its Customers through a mobile network
                               infrastructure.
                               Security domain part of the Profile, owned by the Operator,
                               providing the Secured Channel to the Operator’s OTA Platform.
MNO-SD
                               It is used to manage the content of a Profile once the Profile is
                               enabled.
                               An application residing on a UICC which provides authorisation
Network Access Application
                               to access a network for example a USIM application.
                               A Mobile Network Operator or Mobile Virtual Network Operator;
Operator
                               a company providing wireless cellular network services.
Operator Notification          Operator request to configure Operator specific status change
Configuration (ONC)            notifications for Profiles owned by this Operator.
                               A Profile whose Policy Rules have become unmanageable, for
Orphaned Profile               example due to the termination of the Customer’s contract with
                               the Operator.
                               The credentials included in the Profile, used in conjunction with
OTA Keys
                               OTA Platforms.
                              An Operator platform for remote management of UICCs and the
OTA Platform
                              content of Enabled Operator Profiles on eUICCs.
                              Proprietary application Identifier eXtension, the value of which is
PIX
                              part of the AID.
                              A set of functions related to the enabling, disabling and deletion
                              of a Profile on and the transport of Profile Management
                              functions to an eUICC. Platform Management actions are
Platform Management
                              protected by Platform Management Credentials shared between
                              the SM-SR and the ISD-R. Platform Management does not
                              affect the content of a Profile.
                              A Profile Component is an element of the Profile and may be
                              one of the following:
                              An element of the file system like an MF, EF or DF
Profile Component             An Application, including NAA and Security Domain
                              POL1
                              MNO-SD.
                              Connectivity Parameters.
                              Data required within an eUICC so that a secured communication
Platform Management           can be set up between an external entity and the eUICC in order
Credentials                   to enable, disable and delete Profiles on the eUICC and to
                              transport Profile Management functions.
                              Principles reflected in a set of rules that governs the behaviour
Policy                        of eUICC and/or entities involved in the remote management of
                              the eUICC.
                              Defines the atomic action of a Policy and the conditions under
Policy Rule
                              which it is executed.
                              Combination of a file structure, data and applications to be
                              provisioned onto, or present on, an eUICC and which allows,
Profile
                              when enabled, the access to a specific mobile network
                              infrastructure.
                              Execution of certain Platform Management commands by the
Profile Lifecycle             M2M SP on a Profile, based on prior Profile Lifecycle
Management                    Management Authorisation from the Operator owning the
                              Profile.
Profile Lifecycle             Authorisation given by an Operator to an M2M SP to permit
Management Authorisation      Profile Lifecycle Management. Such authorisations are
(PLMA)                        managed by the SM-SR.
                              A set of functions related to the downloading, installation and
                              content update of a Profile in a dedicated ISD-P on the eUICC.
Profile Management
                              Download and installation are protected by Profile Management
                              Credentials shared between the SM-DP and the ISD-P.
                              Data required within an eUICC so that a Profile downloaded
Profile Management
                              from an external entity can be decrypted and installed on the
Credentials
                              eUICC.
                              Operator specific defined type of Profile. This is equivalent to the
Profile Type
                              "ProfileType" as described in 5.1.1.2.4 of this specification.
                              Registered Application Provider IDentifier, the value of which is
RID
                              part of the AID.
Roles                         Roles are representing a logical grouping of functions.
                              Self-signed certificate of the CI, used to authenticate certificates
Root Certificate
                              issued to other entities.
                              Indication that a command script is split over several secured
                              messages. Script Chaining indicators will specify when to keep
Script Chaining
                              and restore the command context at the boundary of secure
                              channels that transport the different parts of the command script
                              Identification number used by an Application Management
Security Domain Image
                              System to uniquely identify an instance of a Security Domain on
Number (SDIN)
                              a card as specified in GlobalPlatform Card Specification [6].
                              Identification number used by an off-card entity to associate the
                              Security Domain with a specific Card Management System, as
Security Domain Provider      specified in GlobalPlatform Card Specification [6].
Identification Number (SIN)
                              It is an IIN, typically contains the ISO 7812 [19] defined
                              identification of the Security Domain provider.
                              An entity (associated with one or more users) that is engaged in
                              a Subscription with a Telecommunication Service Provider. The
                              Subscriber is allowed to subscribe and unsubscribe to services,
Subscriber
                              to register a user or a list of users authorised to use those
                              services, and also to set the limits relative to the use that
                              associated users make of those services.
                              Describes the commercial relationship between the Subscriber
Subscription
                              and the Telecommunication Service Provider.
                              A unique network address, such as MSISDN, IMSI or SIP-URI,
Subscription Address          of a mobile Subscription within a mobile network. It is used to
                              route messages, for example SMS, to the eUICC.
                              Role that prepares the Profiles to be securely provisioned on the
Subscription Manager Data
                              eUICC and manages the secure download and installation of
Preparation
                              these Profiles onto the eUICC.
Subscription Manager          Role that securely performs functions of Platform Management
Secure Routing                commands and the transport of Profile Management commands.
                              An entity that provides Subscriptions to Subscribers either as
Telecommunication Service     part of an Operator or as a party with a wholesale agreement
Provider                      with an Operator. The Telecommunication Service Provider
                              could also be the Operator.
                              A combination of data and applications to be provisioned on an
                              eUICC to provide connectivity to test equipment for the purpose
Test Profile
                              of testing the Device and the eUICC. A Test Profile does not
                              allow access to an ITU-E.212 [16] network.

1.6 Abbreviations

        Abbreviation                                    Description
AID                           Application Identifier
AES                           Advanced Encryption Standard
CASD                          Controlling Authority Security Domain
CBC                           Cipher Block Chaining
CC                            Cryptographic Checksum
CERT.DP.ECDSA                 Certificate of the SM-DP for its ECDSA key
CERT.SR.ECDSA                 Certificate of the SM-SR for its ECDSA key
CERT.ECASD.ECKA               Certificate of the ECASD for its ECKA key
CI                            Certificate Issuer
CIN                           Card Image Number / Card Identification Number
CMAC                          Cipher-based Message Authentication Code
CRL                           Certificates Revocation List
ECASD                         eUICC Controlling Authority Security Domain
ECDSA                         Elliptic Curve cryptography Digital Signature Algorithm
ECKA                          Elliptic Curve cryptography Key Agreement algorithm
DAP                           Data Authentication Pattern
DGI                           Data Grouping Identifier
DNS                           Domain Name System
DR                            Derivation Random
EUM                           eUICC Manufacturer
EID                           eUICC-ID
EIS                           eUICC Information Set
ETSI                          European Telecommunications Standards Institute
ePK.DP.ECKA                   ephemeral Public Key of the SM-DP used for ECKA
ePK.SR.ECKA                   ephemeral Public Key of the SM-SR used for ECKA
eSK.DP.ECKA                   ephemeral Private Key of the SM-DP used for ECKA
eSK.SR.ECKA                   ephemeral Private Key of the SM-SR used for ECKA
eUICC                         Embedded UICC
FQDN                          Fully Qualified Domain Name
GP                            GlobalPlatform
GSMA                          GSM Association
ICCID                         Integrated Circuit Card ID
IIN                           Issuer Identification Number
IMS                           IP Multimedia Subsystem
IMSI                          International Mobile Subscriber Identity
ISD                           Issuer Security Domain
ISD-P                         Issuer Security Domain Profile
ISD-R                         Issuer Security Domain Root
ISO                           International Standards Organisation
ITU                           International Telecommunications Union
LTE                           Long Term Evolution
LV                            Length Value
M2M SP                        Machine to Machine Service Provider
MEP                           Message Exchange Pattern
MNO                           Mobile Network Operator
MO                            Mobile Originated
MOC                           Mandatory, Optional or Conditional
MT                            Mobile Terminated
NAA                           Network Access Application
ONC                           Operator Notification Configuration
OTA                           Over The Air
PIX                           Proprietary application Identifier eXtension
                              Public Key of the CI in the ECASD for verifying certificate
PK.CI.ECDSA
                              signatures
                              Public Key of the SM-DP, part of the CERT.DP.ECDSA, for
PK.DP.ECDSA
                              verifying its signatures
PK.ECASD.ECKA                 Public Key of the ECASD used for ECKA
                              Public Key of the SM-SR part of the CERT.SR.ECDSA, for
PK.SR.ECDSA
                              verifying its signatures
PLMA                          Profile Lifecycle Management Authorisation
POL1                          Policy Rules within the Profile
                              Policy Rules associated to a Profile and stored in the relevant
POL2
                              EIS at the SM-SR
PoR                           Proof of Receipt
PPK-ENC                       Profile Protection Key for message encryption/decryption
PPK-MAC                       Profile Protection Key for command MAC generation/verification
PPK-RMAC                      Profile Protection Key for response MAC generation/verification
SCP                           Secure Channel Protocol
SD                            Security Domain
SDIN                          Security Domain Image Number
ShS                           Shared Secret
SIN                           Security Domain Provider Identification Number
SK.DP.ECDSA                   Private Key of the of SM-DP for creating signatures
SK.ECASD.ECKA                 Private Key of the ECASD used for ECKA
SK.SR.ECDSA                   Private Key of the SM-SR for creating signatures
SK.CI.ECDSA                   Private key of the CI for signing certificates
SM                            Subscription Manager
SM-DP                         Subscription Manager Data Preparation
SM-SR                      Subscription Manager Secure Routing
SOA                        Service-oriented Architecture
SOAP                       Simple Object Access Protocol
TAR                        Toolkit Application Reference
TLS                        Transport Layer Security
TLV                        Tag Length Value
URI                        Uniform Resource Identifier
URL                        Uniform Resource locator
USIM                       Universal Subscriber Identity Module
XML                        Extensible Markup Language
W3C                        World Wide Web Consortium

1.7 References

           Document
Ref                                                        Title
            Number
                           GSMA ‘Remote Provisioning Architecture for Embedded UICC’
 [1]    SGP.01
                           Version 4.0
                           Smart Cards; ETSI numbering system for telecommunication
 [2]    ETSI TS 101 220
                           application providers; Release 9
 [3]    ETSI TS 102 223    Smart Cards; Card Application Toolkit (CAT) ; Release 9
                           Secured packet structure for UICC based applications; Release
 [4]    ETSI TS 102 225
                           12
 [5]    ETSI TS 102 226    Remote APDU structure for UICC based applications; Release 9
 [6]    GPC_SPE_034        GlobalPlatform Card Specification v.2.2.1
                           GlobalPlatform Card Specification v.2.2.1 UICC Configuration
 [7]    GPC_GUI_010
                           v1.0.1
                           GlobalPlatform Card Specification v.2.2 Amendment B: Remote
 [8]    GPC_SPE_011
                           Application Management over HTTP v1.1.3
                           GlobalPlatform Card Specification v.2.2 Amendment C:
 [9]    GPC_SPE_025
                           Contactless Services v1.1.1
                           GlobalPlatform Card Specification v.2.2 Amendment D: Secure
 [10]   GPC_SPE_014
                           Channel Protocol 03 v1.1.1
                           GlobalPlatform Card Specification v.2.2 Amendment E: Security
 [11]   GPC_SPE_042
                           Upgrade for Card Content Management v1.0.1
                           The international identification plan for public networks and
 [12]   ITU E.212
                           Subscriptions
                           Secured packet structure for (Universal) Subscriber Identity
 [13]   3GPP TS 31.115
                           Module (U)SIM Toolkit applications Release 11
        OMA Smartcard-
 [14]                      OMA-TS-Smartcard_Web_Server-V1_0-20080421-A
        Web-Server v1.0
 [15]   RFC 5246           The TLS Protocol – Version 1.2
                               Pre-Shared Key Cipher suites for Transport Layer Security
[16]   RFC 4279
                               (TLS)
                               Pre-Shared Key Cipher Suites for TLS with SHA-256/384 and
[17]   RFC 5487
                               AES Galois Counter Mode
[18]   RFC 3629                Unicode Transformation Format 8-bit
[19]   ISO/IEC 7812            Identification Cards; Identification of issuers
                               Mobile radio interface Layer 3 specification; Core network
[20]   ETSI TS 124 008
                               protocols; Release 9
[21]   ITU E.118               The international telecommunication charge card
[22]   ITU E.164               International Public Telecommunication Numbering Plan
                               ”GlobalPlatform System”: Messaging Specification for
[23]   GPS_SPE_002
                               Management of Mobile NFC Services, Version 1.1.2
[24]   RFC 4051                Additional XML Security Uniform Resource Identifiers (URIs)
[25]   ETSI TS 102 127         Transport protocol for CAT applications; Release 6
[26]   XML DSIG-CORE           W3C XML Signature Syntax and Processing (Second Edition)
                               Universal Subscriber Identity Module (USIM) Application Toolkit
[27]   3GPP TS 31.111
                               (USAT) ; Release 9
                               Remote APDU Structure for (U)SIM Toolkit applications;
[28]   3GPP TS 31.116
                               Release 9
       3GPP TS 24.341
[29]                           Support of SMS over IP networks; Release 9
       GSMA Security           GSMA Doc Reference: Security Principles Related to Handset
[30]   Principles Related to   Theft 3.0.0
       Handset Theft           EICTA CCIG Doc Reference: EICTA Doc: 04cc100
                               Universal Mobile Telecommunications System (UMTS);
[31]   ETSI TS 123 003
                               Numbering, addressing and identification; Release 9
[32]   RFC 768                 User Datagram Protocol, Aug 1980.
                               Transmission Control Protocol, DARPA Internet Program,
[33]   RFC 793
                               Protocol specification, Sept 1981.
                               GlobalPlatform Card, Secure Element Configuration Version 1.0,
[34]   GPC_GUI_049
                               October 2012
       3GPP TS 27.007          Technical Specification Group Core Network and Terminals;
[35]
                               AT command set for User Equipment (UE) ; Release 9
       NIST SP 800-57 Part     NIST Special Publication 800-57: Recommendation for Key
[36]
       1                       Management – Part 1: General (Revision 3), July 2012
                               BSI – Technische Richtlinie: Kryptographische Verfahren:
[37]   BSI TR-02102
                               Empfehlungen und Schlüssellängen, Version: 2013.02
[38]   GSMA PRD IR.92          GSMA PRD IR.92: IMS Profile for Voice and SMS
                               Technical Specification Group Core Network and Terminals;
[39]   3GPP TS 23.040
                               Technical realisation of the Short Message Service (SMS)
                               SOAP Version 1.2 Part 1: Messaging Framework (Second
[40]   SOAP
                               Edition) http://www.w3.org/TR/soap12-part1/
                           Web Services Addressing 1.0, Core , 9th of May 2006
[41]   WS-Addressing
                           http://www.w3.org/TR/ws-addr-core/
       WS-Addressing-      Web Services Addressing 1.0 - SOAP Binding, 9th of May 2006
[42]
       SOAP-Binding        http://www.w3.org/TR/2006/REC-ws-addr-soap-20060509/
                         Web Services Make Connection (WS-MakeConnection), 2nd
[43]   WS-MakeConnection February 2009, http://docs.oasis-open.org/ws-
                         rx/wsmc/200702/wsmc-1.1-spec-os.html
                           Web Services Security: SOAP Message Security 1.1 (WS-
       WSS-                Security 2004), 1 February 2006,
[44]   SOAPMessageSecur https://www.oasis-
       ity              open.org/committees/download.php/16790/wss-v1.1-spec-os-
                        SOAPMessageSecurity.pdf
       WSS-
                           Web Services Security UsernameToken Profile 1.1, February
[45]   UserNameTokenProf
                           2006, http://docs.oasis-open.org/wss/v1.1/
       ile
       WSS-                Web Services Security X.509 Certificate Token Profile 1.1,
[46]
       X509TokenProfile    February 2006, http://docs.oasis-open.org/wss/v1.1/
                           Extensible Markup Language (XML) 1.0, W3C Recommendation
[47]   XML
                           10-Feb-98, REC-xml-19980210
                           XML Signature Syntax and Processing (Second Edition),W3C
[48]   XML Signature       Recommendation
                           http://www.w3.org/TR/2008/REC-xmldsig-core-20080610/
                           BSI Technical Guideline TR-03111: Elliptic Curve Cryptography,
[49]   BSI TR-03111
                           Version 2.0
                           NIST Special Publication SP 800-56A: Recommendation for
[50]   NIST SP 800-56A     Pair-Wise Key Establishment Schemes Using Discrete
                           Logarithm Cryptography (Revision 2), May 2013
                           Avis relatif aux paramètres de courbes elliptiques définis par
       ANSSI ECC
[51]                       l'Etat français. JORF n°0241 du 16 octobre 2011 page 17533.
       FRP256V1
                           texte n° 30. 2011
                           Characteristics of the Universal Subscriber Identity Module
[52]   3GPP TS 31.102
                           (USIM) application, Release 9
                           SIMalliance: eUICC Profile Package - Interoperable Format
[53]   SIMAPP              Technical Specification v2.3.1, 28 November 2019,
                           http://simalliance.org/euicc/euicc-technical-releases/
                           GlobalPlatform Card Specification v.2.2 Amendment A:
[54]   GPC_SPE_007
                           Confidential Card Content Management v1.0.1
                           NIST Special Publication 800-56C Recommendation for Key
[55]   NIST SP 800-56C
                           Derivation through Extraction-then-Expansion
[56]   SGP.14              GSMA eUICC PKI Certificate Policy v1.1
[57]   RFC 5280            Internet X.509 PKI Certificate and CRL Profile
[58]   RFC 1035            DOMAIN NAMES - IMPLEMENTATION AND SPECIFICATION
[59]   RFC 3596            DNS Extensions to Support IP Version 6
                          Key words for use in RFCs to Indicate Requirement Levels, S.
[60]   RFC 2119           Bradner
                          http://www.ietf.org/rfc/rfc2119.txt
                          FS.04 - Security Accreditation Scheme for UICC Production –
[61]   FS.04
                          Standard v8
                          FS.08 – Security Accreditation Scheme for Subscription
[62]   FS.08
                          Manager - Standard v3
[63]   SGP.05             SGP.05 - Embedded UICC Protection Profile v1.1
[64]   SGP.16             M2M Compliance Process v1.0
                          Internationalized Resource Identifiers (IRIs). January
[65]   RFC 3987
                          2005. http://www.ietf.org/rfc/rfc3987.txt
                          Java Card Classic Platform Specification
[66]   Java Card          https://www.oracle.com/java/technologies/javacard-specs-
                          downloads.html
                          Security architecture and procedures for 5G system (Release
[67]   3GPP TS 33.501
                          15)
[68]   3GPP TS 31.130     (U)SIM API for Java™ Card (Release 15)

1.8 Conventions

The key words "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", and "MAY" in this document SHALL be interpreted as described in RFC 2119 [60].

2 General Parts of the Technical Specification

This section contains a technical description and architecture of the Remote Provisioning System for the Embedded UICC. It SHALL be compliant with the Remote Provisioning Architecture for Embedded UICC [1]. In addition, the statements in this section define the basic characteristics that need to be taken into account when realising this specification.

2.1 General Architecture

This section further specifies the Roles and interfaces associated with the Remote Provisioning and Management of the eUICC, building on GSMA Remote Provisioning Architecture for Embedded UICC [1].

                                                             ES2
CI                                              SM-DP
ES3
                                  Operator
EUM                 ES1
                                                        ES4A
                                           SM-SR
                                                        ES4
                    ES7                                 ES4
SM-SR                                                              M2M-SP
                                     ES8      ES5                                    ES6
                      ESx
Device                                     eUICC
Off-card interface
eUICC interface
Not covered by this specification
Partially covered by this specification
              Figure 1: eUICC Remote Provisioning System

The above figure provides the complete description of the eUICC Remote Provisioning and Management system.

The ES5, ES6, ES8 and ESx interfaces are described in section 4.

The ES1, ES2, ES3, ES4 and ES7 interfaces are described in section 5.

NOTE:Functions of the ES2 interface related to Profile ordering and master delete are considered out of the scope of this specification as these functions may be based upon pre-existing Operator processes.

NOTE:The interface between the SM-DP and EUM and the related function for Profile Creation is out of the scope of this specification as this function is based upon proprietary mechanisms.

NOTE:The ES6 interface is based on the RAM and RFM mechanisms described in ETSI TS 102 225 [4] and ETSI TS 102 226 [5].

NOTE:As defined in GSMA Remote Provisioning Architecture for Embedded UICC [1], the Initiator Role is assumed to be played by the Operator and functions related to this Role are specified in the ES4 interface.

NOTE:ESx and its related operations for Emergency and Test Profiles (Local Enabling and Local Disabling), as well as the support of the Emerg ency Profile and Test Profile, are optional features.

2.2 eUICC Architecture

This section focuses on the eUICC architecture which widely leverages current telecommunication standards, as well as GlobalPlatform standards that are especially well adapted to establish Role separation and data isolation. In particular, each entity will have a dedicated Security Domain with different privileges and configuration.

2.2.1 Security Domains

The eUICC architecture comprises the following Security Domains for the purpose of Platform and Profile Management:

   The ISD-R is the representative of the off-card entity SM-SR
   The ECASD is the representative of the off-card entity CI
   An ISD-P is the representative of an off-card entity SM-DP. An eUICC can contain
    more than one ISD-P
ISD-R                   ECASD
           AM                                               AM
ISD-P 1                                         ISD-P n
Profile                  …                       Profile

Figure 2: Security Domain Architecture Overview

An ISD, as specified in GlobalPlatform Card Specification [6], does not exist in the architecture of the eUICC.

2.2.1.1 ISD-R

There SHALL be only one ISD-R on an eUICC.

The ISD-R SHALL be installed and first personalized by the EUM during eUICC manufacturing. The ISD-R SHALL be Associated with itself.

After eUICC manufacturing, the ISD-R SHALL be in life-cycle state PERSONALIZED as defined in GlobalPlatform Card Specification [6], section 5.3. The LOCKED state SHALL NOT be supported by the ISD-R.

The ISD-R privileges SHALL be granted according to Annex C.

The ISD-R SHALL only be able to perform Platform Management functions on ISD-Ps.

2.2.1.2 ECASD

There SHALL be only one ECASD on an eUICC.

The ECASD SHALL be installed and personalized by the EUM during the eUICC manufacturing. The ECASD SHALL be Associated with the ISD-R.

After eUICC manufacturing, the ECASD SHALL be in life-cycle state PERSONALIZED as defined in GlobalPlatform Card Specification [6], section 5.3.

The ECASD is involved in the following functions:

      SM-DP key set establishment for Profile Download and Installation
      SM-SR key set establishment for SM-SR Change

The ECASD SHALL be personalized by the EUM during eUICC manufacturing with:

      PK.CI.ECDSA
      SK.ECASD.ECKA
      CERT.ECASD.ECKA for eUICC Authentication and key establishment
      EID

The ECASD SHALL comply with the requirements defined for the CASD in GlobalPlatform Card Specification UICC configuration [7] except:

      AIDs and TAR SHALL be allocated as defined in section 2.2.3
      Support of SCP 02 is not required
      Only the ISD-R and ISD-Ps SHALL be able to use the ECASD services

2.2.1.3 ISD-P

An ISD-P hosts a unique Profile.

Only one ISD-P SHALL be enabled on an eUICC at any point in time.

An ISD-P SHALL be installed by the ISD-R and then personalized by its related SM-DP (see section 3.1.1). At least one ISD-P with a Profile SHALL be installed and first personalized by the EUM during eUICC manufacturing to allow future eUICC connectivity.

The ISD-P SHALL be able to receive and process a Profile Package, wrapped in an SCP03t Secure Channel, as specified in section 4.1.3.3.

The eUICC SHALL support the SIMalliance: eUICC Profile Package - Interoperable Format Technical Specification [53] with the major version being 2 and the version being at least 2.3.1. The eUICC MAY in addition support higher major versions. The EUM SHALL indicate in the EIS the versions supported by the eUICC, as specified in section 5.1.1.2.10.

No component outside the ISD-P SHALL have visibility or access to any Profile component with the exception of the ISD-R, which SHALL have read access to POL1 and to the Connectivity Parameters as defined in section 4.1.3.4.

A Profile Component SHALL NOT have any visibility of, or access to, components outside its ISD-P. An ISD-P SHALL NOT have any visibility of, or access to, any other ISD-P.

It SHALL be possible to allocate the same AID within different Profiles. A Profile Component SHALL NOT use the reserved ISD-R, ISD-P and ECASD AIDs.

It SHALL be possible to allocate the same TAR within distinct Profiles. A Profile Component SHALL NOT use the reserved ISD-R, ISD-P and ECASD TARs.

An ISD-P SHALL remain associated to the ISD-R during all its life time in order for the ISD-R to be able to perform the Platform Management functions:

       ISD-P Creation: the Association between the ISD-R and an ISD-P SHALL be created
        at that time
       ISD-P Deletion and Master Delete
       Profile Enabling and Disabling
       Fall-Back Attribute setting
       Transport function: The Association SHALL allow SCP03/SCP03t establishment
        between the SM-DP and the ISD-P.

ISD-P SHALL follow the life-cycle illustrated in the Figure 3, based on the Security Domain life-cycle defined in GlobalPlatform Card Specification [6], section 5.3.

1 (ISD-P creation)

                   1
SELECTABLE             delete

2 (key establishment)

 PERSONALIZED        1
                         delete
(Profile creation)

2 (successful profile download)

                1
DISABLED            delete
 Transitions triggered by:
1 – ISD-R                                             1              3
2 - The ISD-P itself
3 - Fall-back mechanism
                                                          ENABLED

Figure 3: ISD-P Life-Cycle State Transitions

After execution of the procedure described in section 3.1.1, the ISD-P SHALL be in SELECTABLE state. After execution of the procedure described in section 3.1.2, the ISD-P SHALL be in PERSONALIZED state.

NOTE:The INSTALLED state for security domains defined in GlobalPlatform Card Specification [6] is skipped by the command for ISD-P creation defined in section 4.1.1.1.

After execution of the procedure described in section 3.1.3 or 3.4, the ISD-P SHALL be in the DISABLED state. The ISD-P can also transition to the DISABLED state as the result of the enabling of another ISD-P as described in section 3.2, or the activation of the Fall-Back Mechanism.

After execution of the procedure described in section 3.2, the ISD-P SHALL be in the ENABLED state. The ISD-P can also transition to the ENABLED state as the result of the activation of the Fall-Back Mechanism.

Deletion removes the ISD-P with its Profile from the eUICC.

The LOCKED state SHALL NOT be supported by an ISD-P.

For coding the states, table 11-5 of GlobalPlatform Card Specification [6] is modified as follows:

b8 b7 b6 b5 b4 b3 b2                   b1    Meaning
  0    0      0      0   0   0    1     1    (INSTALLED)
  0    0      0      0   0   1    1     1    SELECTABLE
                                             PERSONALIZED (Profile
  0    0      0      0   1   1    1     1
                                             creation)
  0    0      0      1   1   1    1     1    DISABLED
  0    0      1      1   1   1    1     1    ENABLED

Table 1: ISD-P Coding States

These states can be mapped to the architectural states defined in GSMA Remote Provisioning Architecture [1] as shown below:

State (as defined in [1])     State (as defined above)
                            (INSTALLED)
Created                     SELECTABLE
                            PERSONALIZED
Disabled                    DISABLED
Enabled                     ENABLED
Deleted                     No explicit mapping; ISD-P no
                            longer exists on the eUICC

Table 2: ISD-P State Mapping

ISD-P privileges SHALL be granted according to Annex C.

All Profile Components, in particular the MNO-SD, SHALL remain linked to the ISD-P in order to enable the following:

    Profile Download and Installation: the Profile Components, which are affiliated with
     the ISD-P, are created at that time
    ISD-P Deletion and Master Delete: the Profile Components SHALL be deleted at that
     time
    Profile Enabling and Disabling: Enable and Disable access to all the Profile
     Components
    Update of POL1
    Provide read access to POL1 when required for Platform Management functions.

The Application privileges (defined in GlobalPlatform Card Specification [6]) assigned to a Profile Component SHALL apply according to Annex C.

All Profile Components created by the ISD-P SHALL always remain affiliated with the ISD-P. In particular it is not possible to change the affiliation of any Profile Component.

When an ISD-P is not in enabled state, the eUICC SHALL ensure that:

    Remote management of any Profile Component is not possible via the ES6 interface;
    The file system within the Profile cannot be selected by the Device or any application
     on the eUICC;
    The applications (including NAAs and Security Domains) within the Profile cannot be
     selected, triggered or deleted.

2.2.2 Identification of eUICC: EID

The EID is the eUICC identifier used in the context of Remote Provisioning and Management of the eUICC.

The EID SHALL be stored within the ECASD and can be retrieved by the Device at any time using the standard GlobalPlatform GET DATA command by targeting the ECASD as specified in GlobalPlatform Card Specification [6] as follows:

    Select the ECASD using the SELECT command with the AID value defined in section
     2.2.3
    Send a ‘GET DATA’ command to the ECASD with the data object tag '5A' to retrieve
     the EID

The EID SHALL have the following structure:

    The EID SHALL always be 32 digits long
    The EID SHALL always be built of
         o A Major Industry Identifier digit of 8 (1 st digit), as defined in ISO/IEC 7812 [19].
         o An additional digit of 9 specifying telecommunications, as defined in ISO/IEC
              7812 [19],
         o An additional three digits for country code (3 rd to 5th digits).
                    If the country code is one digit long, its value SHALL be prefixed by
                       two digits of 0,
                    If the country code is two digits long, its value SHALL be prefixed by
                       one digit of 0.
         o An additional three digits for issuer identifier (6 th to 8th digits)
                    If the issuer identifier is one digit long, its value SHALL be pre fixed by
                       two digits of 0,
                    If the issuer identifier is two digits long, its value SHALL be prefixed by
                       one digit of 0.
         o An additional ten digits for issuer specific information (9 th to 18th digits), of
              which the first five digits (9 th to 13th) contain version information about the
              platform and OS, to be specified by the issuer and the last five digits (14 th to
              18th) contain additional issuer information,
         o An additional twelve digits for the individual identification number (19 th to 30th
              digits),
         o A last two digits (31st to 32nd digits) containing check digits calculated over all
              32 digits as specified below.
    The country code and issuer identifier SHALL be assigned as specified in ITU E.118
     [21]
    The two check digits are calculated as follows:
         o 1. Replace the two check digits by two digits of 0,
         o 2. Using the resulting 32 digits as a decimal integer, compute the remainder
              of that number on division by 97,
         o 3. Subtract the remainder from 98, and use the decimal result for the two
              check digits,
                    If the result is one digit long, its value SHALL be prefixed by one digit
                       of 0.
    When stored as a byte string, the first digit SHALL be put into the highest four bits of
     the first byte

Annex J provides a description of how the verification of an EID is performed.

2.2.3 Identification of Security Domains: AID and TAR

The ISD-P AID, the ISD-R AID and the ECASD AID SHALL follow the structure specified in ETSI TS 101 220 [2], with a RID and a PIX. The ISD-P AID, the ISD-R AID and the ECASD AID SHALL be 16 bytes long including the TAR.

The RID of the Executable Load File, the Executable Module and the Application of the ISD - R, the ISD-P and the ECASD SHALL be set to 'A000000559' (as defined in ISO/IEC 7816 - 5:2004).

The ISD-R application SHALL be installed by the EUM during eUICC manufacturing. The ISD-R Executable Load File AID and the ISD-R Executable Module AID can be freely selected by the EUM.

The ISD-R application AID SHALL be ‘A0 00 00 05 59 10 10 FF FF FF FF 89 00 00 01 00' as defined into Annex H.

The ECASD application SHALL be installed by the EUM during eUICC manufacturing. The ECASD Executable Load File AID and the ECASD Executable Module AID can be freely selected by the EUM.

The ECASD application AID SHALL be ‘A0 00 00 05 59 10 10 FF FF FF FF 89 00 00 02 0 0' as defined into Annex H.

The ISD-P application SHALL be installed by SM-SR during the first step of the “Profile Download and Installation” procedure in section 3.1.

The ISD-P Executable Load File AID SHALL be ‘A0 00 00 05 59 10 10 FF FF FF FF 89 00 00 0D 00' as defined into Annex H.

The ISD-P Executable Module AID SHALL be ‘A0 00 00 05 59 10 10 FF FF FF FF 89 00 00 0E 00' as defined into Annex H.

The ISD-P application AID SHALL be coded according to Annex H. The SM-SR SHALL allocate the ISD-P application AID in the range defined in Annex H.

NOTE:The choice of having the ISD-P AID allocated by the SM-SR is to avoid conflicts with other ISD-P AIDs used by already installed ISD-Ps; the SM-DP cannot have such visibility.

The MNO-SD application AID and TAR(s) can be freely allocated by the Operator during Profile definition.

2.2.4 Profile Structure

The Profile structure, composed of a set of Profile Components, is specified by, and under the full control of, the Operator. The full Profile structure SHALL be contained in a unique ISD-P.

The Profile structure SHALL contain a Profile Component, called MNO-SD, which performs an identical Role as the ISD for a UICC (see GlobalPlatform Card Specification [6]). This MNO-SD is the representative of the Operator owning the Profile, meaning it contains the Operator’s OTA Key sets.

                          AM
               ISD-P
                      -SM-DP_Keyset_scp03
                               Connectivity
POL1
                               Parameters
              AM
MNO-SD
          -MNO_Keyset_scp80
          -MNO_Keyset_scp81 (opt.)
          -MNO other keysets (opt.)

FileSystem

CASD                           NAA

SSD

Application

GP association link

Figure 4: Profile Structure Overview

The Profile in the Figure 4 provides an example of a Profile structure.

The Profile structure SHALL include:

   The MNO-SD
   At least one NAA
   POL1, even if not used
   The file system
   Connectivity Parameters of the Profile

The Profile structure MAY contain:

   Several Applications (as defined in GlobalPlatform Card Specification [6]) in addition
    to the MNO-SD
   One CASD (as defined in GlobalPlatform Card Specification UICC Configuration [7])

The privileges that can be allocated to the MNO-SD and to applications SHALL comply with Annex C.

It SHALL be possible for the Operator to establish secure channels between the Operator OTA Platform and security domains of the Profile as specified in ETSI TS 102 225 [4] and ETSI TS 102 226 [5].

2.2.5 Secure Channel on Interfaces

2.2.5.1 Secure Channel on ES5 (SM-SR-eUICC)

The ES5 functions are addressed to the eUICC through a secure channel established between the SM-SR and the ISD-R. The eUICC SHALL support SCP80 and may support SCP81 (defined in ETSI 102 225 [4] and ETSI 102 226 [5]). See also section 2.4.

To enable SCP80, the ISD-R SHALL be personalized before issuance by the EUM with at least one key set, with a Key Version Number between ‘01’ to ‘0F’ following GlobalPlatform Card Specification UICC Configuration [7].

To enable SCP81, the ISD-R SHALL be personalized with at least one key set, with a Key Version Number between ‘40’ to ‘4F’ following GlobalPlatform Secure Element Configuration [34].

The key length and algorithm SHALL comply with section 2.3.3.

The key sets SHALL be loaded in the ISD-R, and provided to SM-SR, in the EIS, through ES1

                     SCP80 or SCP81
SM-SR         ES5 function             ISD-R

-Keyset_scp80 - Keyset_scp81 (opt.) - Keyset_scp80 - Keyset_scp81 (opt.)

Off-card                                                                 eUICC

Figure 5: Secure Channel Between SM-SR and ISD-R

2.2.5.2 Secure Channel on ES8 (SM-DP - eUICC)

The ES8 functions are addressed to the eUICC through a secure channel established between the SM-DP and its ISD-P. The eUICC SHALL support SCP03 for ES8 (as defined in GlobalPlatform Card Specification Amendment D [10], as well as the variant SCP03t defined in this specification (see section 4.1.3.3).

NOTE:SCP03 is the only secure channel defined by GlobalPlatform that complies with requirements of the section 2.3.3.

To enable SCP03 and SCP03t, the ISD-P SHALL be personalized with at least one key set, with a Key Version number between ‘30’ to ‘3F’ (see GlobalPlatform Secure Element Configuration [34]).

The secure channel configuration, key length and algorithm to be used SHALL comply with section 2.5.

The first SCP03 key set is loaded into the ISD-P by its SM-DP as described in the procedure “Key Establishment with Scenario#3-Mutual Authentication”, section 3.1.2.

              ES8 function                                 SCP03/SCP03t
SM-DP                                                                                                            ISD-P
                 Secure Channel                        SCP80 or SCP81
                                   SM-SR                                     ISD-R
                                                                            - Keyset_scp80                  - Keyset_scp03
                                                                            - Keyset_scp81 (opt.)
- Keyset_scp03                     - Keyset_scp80
                                   - Keyset_scp81 (opt.)
Off-card                                                                    eUICC
 Figure 6: Secure Channel Between SM-DP and ISD-P

2.2.5.3 Secure Channel on ES6 (Operator-eUICC)

The ES6 functions are addressed to the eUICC through a secure channel (as defined in ETSI TS 102 225 [4] and ETSI TS 102 226 [5]) established between the Operator and the MNO-SD (as defined in section 2.2.3).

NOTE:The Operator can also communicate with any other SSD (of the Profile) belonging to the Operator. The Figure 7 only illustrates the secure channel with the MNO-SD.

The initial OTA Key sets are part of the Profile and are loaded by the SM-DP during the “Profile Download and Installation”, see section 3.1, or loaded by the EUM before eUICC issuance.

Profile

 MNO          ES6 function                                 SCP80 or SCP81                                        MNO-SD
                                                                                                            -Keyset_scp80
                                                                                                            -Keyset_scp81 (opt.)
                                                                                                            -other keysets (opt.)
-Keyset_scp80
-Keyset_scp81 (opt.)
-other keysets (opt.)
                        Off-card                                                                    eUICC
                     Figure 7: Secure Channel Between Operator and MNO-SD

2.2.6 eUICC OS Update

An eUICC should support a secure mechanism to allow the eUICC OS Update when the eUICC is in the field. Such mechanism allows the eUICC Manufacturer to correct errors in existing features on the eUICC. When an eUICC OS Update mechanism is supported, it SHALL be declared in the EIS through OSUpdateSupported in the AdditionalProperties field.

The process and mechanisms are EUM implementation specific and therefore out of scope of this specification.

In case an eUICC OS Update happens, the EUM SHALL ensure that:

      the resulting eUICC SHALL maintain, at least, the same level of security and
       functional compliance than the previous eUICC.
      The EIS additional property updatedPlatformVersion is updated to reflect the change
       of Operating System version

After an update of the EIS, the SM-SR SHOULD take implementation-dependent actions to also update the EIS field “remainingMemory”.

2.2.7 Java Card™ Support

The eUICC MAY support Java Card™. If Java Card™ is supported, the eUICC SHALL support at least version 3.0.4 of the Java Card Classic Platform Specification [66].

2.3 Security Overview

This section provides an overview of the overall ecosystem security features.

The expectation of this architecture is to provide a solution offering a security level at least equivalent to the security reached by the current UICC and its management systems.

The security requirements have to be applied to the different Actors and Roles (Customer, Operator, SM-DP, SM-SR, CI, eUICC and eUICC Manufacturer). Each Role is considered as elements which can belong to a security realm and has to fulfil the appropriate certification compliance criteria (see section 2.9).

In addition to the intrinsic security of each security realm, the data exchanged between these entities has to be protected. Any communication between two security realms of the eUICC ecosystem SHALL be origin authenticated, as well as integrity-Protected and, unless otherwise specified in detailed sections of this specification, confidentiality protected.

For all the procedures described in this specification the security realms are mutually authenticated and they have negotiated a minimal-acceptable common cryptographic suite for further communication.

For the eUICC interfaces, the Platform Management commands (ES5) and the OTA Platform commands (ES6) SHALL be protected by either a SCP80 or SCP81 secure channel with security level defined in section 2.4. The Profile Management commands (ES8) SHALL be at least protected by a SCP03 security level as detailed in section 2.5.

Off-card entities SHALL implement access control mechanisms for all function execution and data access requests. This access SHALL be authorised and any access SHALL be traced as defined in the GSMA certification schemes.

2.3.1 Certificate Issuer Role

The Certificate Issuer (CI) Role issues the certificates for the eUICC Remote Provisioning System and acts as a trusted third party for the purpose of mutual authentication of the entities of the system. The CI provides:

   A self-signed Root Certificate used to verify certificates issued and signed by the CI
   A public key (PK.CI.ECDSA), part of that Root Certificate, used on the eUICC to
    verify certificates issued by the CI
   A certificate (CERT.DP.ECDSA, signed by the CI) to authenticate the SM-DP. This
    certificate is used in the “Load and Install Profile” procedure
   A certificate (CERT.SR.ECDSA, signed by the CI) to authenticate the SM-SR. This
    certificate is used in the “SM-SR change” procedure
    A certificate, signed by the CI, to authenticate the EUM. This certificate is used in the
     "Download and Install Profile" and in the “SM-SR change” procedures.
    A Certificate Revocation List (CRL), issued periodically or on event, as specified in
     the GSMA eUICC PKI Certificate Policy SGP.14 [56]. This CRL lists identifiers of the
     certificates issued by the CI that have been revoked before their expiration date.

2.3.2 Certification Chains

The Certificate Issuer Role issues certificates for Embedded UICC remote provisioning system entities and acts as a trusted root for the purpose of authentication of the entities of the system. The following certificates SHALL be signed and issued by the CI, according to the policies specified in SGP.14 [56]:

    Self-signed Root Certificate
    EUM Certificates
    SM-SR Certificates
    SM-DP Certificates

The EUM, SM-SR, and SM-DP certificates, SHALL be requested to the CI, following the procedures, and using the CSR formats, defined in SGP.14 [56].

The Self-signed Root certificate, and the EUM certificates, SHALL follow the format specified by SGP.14 [56], based on X.509, including in particular exte nsions SubjectAltName and SubjectKeyIdentifier.

The SM-SR, SM-DP, and eUICC certificates, SHALL follow the format specified by this document, in sections 4.1.1 and 4.1.3, based on Global Platform Amendment E [11]

The following certificates SHALL be signed and issued by the EUM:

    eUICC Certificates
       CI
Root Certificate
 (self signed)
    Public Key for
signature verification
   Private Key for
      signature
    EUM                     SM-SR                                     SM-DP
EUM Certificate         SM-SR Certificate                         SM-DP Certificate
 (signed by CI)          (signed by CI)                            (signed by CI)
    Public Key for            Public Key                                Public Key
signature verification      (PK.SR.ECDSA)                             (PK.DP.ECDSA)
   Private Key for            Private Key                               Private Key
      signature             (SK.SR.ECDSA)                             (SK.DP.ECDSA)
   eUICC
eUICC Certificate
(signed by EUM)                             A                          B
                                       B certificate is signed by A private key
   Public Key
(PK.ECASD.ECKA)
   Private Key
(SK.ECASD.ECKA)

Figure 8: Certificate Chains

The certificate operational period and key pair usage period of all certificates SHALL be set to the time limits defined in SGP.14 [56] section 8.2.

2.3.2.1 Management of certificates on eUICC

The following certificates SHALL be checked by the eUICC:

      the SM-SR Certificate
      the SM-DP Certificate

The following certificate and key SHALL be stored in the eUICC:

      the eUICC Certificate
      the public key allowing to verify SM-SR and SM-DP certificates

The eUICC Certificate is part of the EIS (eUICC Information Set) which is stored in the SM- SR and/or at EUM level. This certificate contains:

      The PK.ECASD.ECKA used for ElGamal Elliptic Curves key agreement as defined in
       GlobalPlatform Card Specification Amendment E [11]
      The EID
      The technical reference of the product, which allows the Common Criteria (CC)
       certification report to be identified by Common Criteria certification body (for example
       BSI, ANSSI).

2.3.2.2 Identification of parent certificates

It is recognized that the CA-ID field (tag 42) in a GlobalPlatform certificate is usually filled with the identifier of the organization that issues the certificate. In case this organization has more than one key pair that can be used to sign issued certificates, this tag alone is not sufficient to distinguish which parent key pair was used.

In the context of this specification, an additional identifier of the parent key pair SHALL therefore be provided in the parent certificate as an extension SubjectKeyIdentifier, (as described in RFC 5280 [57]).

This identifier SHALL be referenced in the child certificates as an extension Authority Key Identifier (as described in RFC 5280 [57]) in the EUM certificate, or as a tag C9 Authority Key Identifier within the discretionary data field (tag 73) for eUICC, SM-SR, and SM-DP certificates.

When the Authority Key Identifier extension or tag is present, its value SHALL match the value of the Subject Key Identifier extension of the parent certificate.

2.3.2.3 Certificate revocation management

The EUM Certificate, SM-DP Certificate, and SM-SR Certificate, can be revoked by the CI for
a number of reasons, described in SGP.14 [56], and following procedures described in the
same document for the triggering and evaluation of the revocation request, and for the
information of relying parties after revocation.
The Operator SHOULD consider the revocation status of the EUM Certificate before
downloading their Profile on an eUICC whose EIS and ECASD Certificate was signed by the
EUM private key.
The Operator SHOULD consider the revocation status of the Certificate of the SM-DP and
SM-SR which manage the Operator’s Profiles.
   NOTE:      This can be achieved by retrieving regularly the most up-to-date CRL issued
              by the CI, and check if any Certificate of their EUM, SM-DP SM-SR supplier
              is listed. From this point the Operator can inspect the reason for revocation.
As a general recommendation, the Operator SHOULD NOT download a Profile on an eUICC
whose EUM Certificate was revoked. And the Operator SHOULD avoid to manage its Profiles
via an SM-DP or an SM-SR whose certificate has been revoked.
However, based on the revocation information, the Operator can make an informed decision
as to whether it can continue to rely on the eUICC, SM-SR, SM-DP, at the Operator’s own
risk, as stipulated in SGP.14 [56]. The SM-DP and SM-SR SHALL obey the Operator’s
informed decision:
      When an Operator requests the SM-DP to download a Profile on an eUICC, the SM-
        DP SHALL NOT refuse to download the Profile for the sole reason that the EUM
        certificate has been revoked.
      When an Operator requests a Profile Management or Platform Management
        operation, the SM-DP SHALL NOT refuse to perform the operation for the sole reason
        that the SM-SR Certificate has been revoked.
      When receiving an EIS via ES1 or ES7, the SM-SR SHALL NOT refuse to register the
        eUICC for the sole reason that the EUM Certificate has been revoked.
    When an Operator requests a Profile Management or Platform Management
     operation, the SM-SR SHALL NOT refuse to perform the operation for the sole reason
     that the EUM Certificate has been revoked.
    When an M2M SP requests a Profile Lifecycle Management operation, the SM-SR
     SHALL NOT refuse to perform the operation for the sole reason that the EUM
     Certificate has been revoked.
    When an Operator requests a Profile Management or Platform Management operation
     via the SM-DP, the SM-SR SHALL NOT refuse to perform the operation for the sole
     reason that the EUM Certificate has been revoked.
    When transferring an eUICC to another SM-SR2 via SM-SR Change, the SM-SR1
     SHALL NOT refuse to perform the operation for the sole reason that the SM-SR2
     Certificate has been revoked.
NOTE          The above ensures that the eUICC doesn’t need to manage the revocation
              status of the SM-DP certificate or the SM-SR certificate that it receives.

2.3.3 General Consideration on Algorithm and Key Length

Following the recommendations of several security agencies (for example NIST: SP 800 -57 Part 1: Recommendation for Key Management [36], which was last revised in 2012; BSI: TR- 02102: Kryptographische Verfahren: Empfehlungen und Schlüssellängen [37], which was updated in 2013. For an overview see also http://www.keylength.com/en/2/), the following table provides an overview of the key lengths and hashing methods that SHALL be applied in the context of this specification to ensure a good level of security up to the horizon 2030:

Algorithm                                         Minimum Key Length
Symmetric (AES)                                   128 bits, block size of 128 bits
Asymmetric (RSA)                                  3072 bits
Elliptic curve                                    256 bits
Hashing for Digital signatures and hash-only      SHA-256
applications
Hashing for HMAC, Key Derivation Functions and    SHA-256
Random Number Generation

Table 3: Algorithm and Key Length

2.4 OTA Communication on ES5 (SM-SR-eUICC)

2.4.1 General OTA Requirements

In the eUICC Remote Provisioning and Management system the OTA communication is exclusively handled by the SM-SR. The SM-SR can use SMS, CAT_TP and HTTPS for remote OTA communication with the eUICC.

   The eUICC SHALL support SMS and either CAT_TP or HTTPS or both.
   Device requirements are stated in Annex G.
   The SM-SR SHALL support SMS, HTTPS and CAT_TP.
    In HTTPS case, the SM-SR and eUICC MAY support DNS resolution to resolve the
     IP address of the SM-SR
    For LTE network deployments the system SHALL support SMS as defined in GSMA
     PRD IR.92 [38].
    The SM-SR is free to select the most relevant protocol according to the eUICC and
     Device capabilities and the platform or Profile Management operation to execute.
    The eUICC SHALL support the RAM and RFM as defined in ETSI TS 102 226 [5], in
     particular Expanded Remote Application data format and Script Chaining.

2.4.2 Void

2.4.3 SMS

The usage of the SMS protocol may be relevant in several situations:

    SMS for HTTPS session triggering, as defined in ETSI TS 102 226 [5], and also in
     OMA-Smart Card Web Server [14] (section “Remote Administration Request sent
     using a MT-SMS”)
    SMS for CAT_TP session triggering as defined in ETSI TS 102 226 [5].
    When a command to be sent to the eUICC can fit into a few SMS; such a solution can
     be more efficiently handled via SMS, as compared to HTTPS.

The eUICC SHALL support the sending of secure packet over SMS as defined in 3GPP TS 31.115 [13]

The eUICC SHALL support RAM over SMS as defined in ETSI TS 102 226 [5].

The eUICC SHALL comply with 3GPP TS 31.111 [27] and 3GPP TS 31.116 [28].

Except for the notification described in section 3.15.1, concerning the security level, the SMS (MT or MO) SHALL make use of a CC with a length of 64 bits using AES CMAC mode, ciphering using AES in CBC mode and counter value higher (SPI1=’16’). Minimum ke y lengths are defined in section 2.3.3.

    Procedures for the PoR SHALL follow ETSI TS 102 225 [4] and 3GPP TS 31.115
     [13] with the following precisions: in the case that an incoming SMS for the ISD-R
     does not meet this security level, it must be rejected by the eUICC and no PoR
     SHALL be sent back
    When the eUICC cannot authenticate the SM-SR, it SHALL NOT send any PoR and
     discard the command packet with no further action being taken.

SPI2 SHALL be set to:

    ‘00’: no PoR (this value SHALL only be used for the notification described in section
     3.15.1 and optionally for the SMS for HTTPS session triggering described in section
     2.4.3.1),
    or to ‘39’: PoR with CC and encryption.

When a PoR is returned, the SMS SHALL make use of a CC with a length of 64 bits using AES CMAC mode , ciphering using AES in CBC mode and SHALL be sent using SMS- SUBMIT mode. Minimum key lengths are defined in section 2.3.3.

The SM-SR SHALL verify that the counter value of the PoR is the same as the counter value sent in the command packet.

All these security requirements SHALL apply also for the SCP80 secured packets exchanged during a CAT_TP session.

2.4.3.1 SMS for HTTPS Session Triggering

The SM-SR SHALL make use of a special SMS for triggering the opening of an HTTPS session to the eUICC.

This SMS SHALL be addressed to the ISD-R. The necessary TAR information SHALL be included in the EIS. The SMS SHALL comply with the format described in GlobalPlatform Card Specification Amendment B [8], section “Administration session triggering parameters” .

The SM-SR MAY choose to request a PoR or not for this special SMS, and set the SPI2 byte of the SMS accordingly.

NOTE:Normally the SM-SR will close the session. However, if needed, the eUICC MAY close the session.

2.4.3.2 SMS for CAT_TP Session Triggering

The SM-SR SHALL make use of a special SMS for triggering the opening of a CAT_TP session to the eUICC.

This SMS SHALL be addressed to the ISD-R. The necessary TAR information SHALL be included in the EIS. The SMS SHALL comply with the format described in:

      ETSI TS 102 226 [5], using the parameter “Request for BIP channel opening” and
       “Request for CAT_TP link establish”. These parameters and the corresponding “Data
       for BIP channel opening” and “Data for CAT_TP link establishment” are separated in
       two different commands sent in the same push SMS.

NOTE:Normally the SM-SR will close the session. However, if needed, the eUICC MAY close the session.

2.4.3.3 Command Format in SMS

The commands sent to the eUICC within a secure script in SMS SHALL be formatted as an expanded remote command structure as defined in ETSI TS 102 226 [5]. As a consequence, the eUICC SHALL provide the answer as an expanded remote response structure.

2.4.4 HTTPS

If HTTPS is used, the following sections SHALL apply.

2.4.4.1 PSK-TLS

2.4.4.1.1 Cipher Suites

The eUICC SHALL support the Transport Layer Security (TLS) protocol v1.2 [15] and SHALL support at least one of the following Pre-Shared Key Cipher suites as defined in RFC 5487 [17]:

      TLS_PSK_WITH_AES_128_GCM_SHA256
      TLS_PSK_WITH_AES_128_CBC_SHA256

The Pre-Shared Keys SHALL have an entropy of at least 128 bits. The eUICC ISD-R SHALL be configured with ‘i’ = ‘04’ to indicate only TLS 1.2 supported as defined in GlobalPlatform Amd B [8]. The SM-SR SHALL select a cipher suite of the same or higher security compared to the two listed above.

2.4.4.1.2 PSK-ID Value for TLS Handshake

The PSK-ID specified in this section defines a format suited for PSK random keys. However, a SM-SR MAY use a dedicated PSK-ID format in particular to be able to manage PSK derived from master key. In this case the derivation algorithm used SHALL be robust and follow the NIST recommendation SP800-56C [55], the derived Pre-Shared Keys SHALL have an entropy of at least 128 bits.

As specified in RFC 4279 [16], the PSK Identity SHALL be first converted to a character string, and then sent encoded in octets using UTF -8 [18] by the eUICC.

In the context of this specification, the PSK Identity before conversion is a sequence of Tag/Length/Value (TLV) objects in hexadecimal string representation.

NOTE:As the PSK Identity is expected to be as short as possible, all lengths are coded in one byte. BER-TLV coding is unnecessary in this case.

                                    Length
Description                                   Value
                                    (bytes)
Tag for identifying PSK-ID format   1         ‘80’
Length                              1         ‘01’
Identification of the PSK-ID        1         Expected value is ‘02’ indicating a full qualified
format.                                       format for random PSK.
Tag for indicator of EID            1         ‘81’
Length of EID                       1         ‘10’
EID value                           16        The EID value. The value SHALL be coded in
                                              hexadecimal string representation.
Tag for security domain AID         1         ‘4F’
Length of security domain AID       1         ‘10’
Security domain AID value           16        The AID value of the ISD-R. The value SHALL
                                              be coded in hexadecimal string representation.
Tag for key identifier                    1           ‘82’
Length                                    1           ‘01’
Key identifier                            1           The key identifier value. The value SHALL be
                                                      coded in hexadecimal representation.
Tag for Key version                       1           ‘83’
Length                                    1           ‘01’
Key version                               1           The key version value. The value SHALL be
                                                      coded in hexadecimal representation. Key
                                                      version number range reserved for SCP81 is '40'
                                                      to '4F'.

Table 4: PSK-ID Format

Example of PSK-ID before conversion to an UTF-8 string:

‘8001028110010203040506070809010203040506074F10000102030405060708090A0B0C 0D0E0F820101830140’

2.4.4.1.3 Other restrictions on TLS session management

In addition to restrictions to the TLS protocol specified in GP Amendment B [8], the ISD-R and SM-SR SHALL NOT support TLS Session resumption (RFC 4507 or RFC 5077) nor several parallel TLS sessions.

2.4.4.2 HTTP POST Request of ISD-R

The POST request is used by the ISD-R to fetch remote APDU strings and to transmit response strings. The ISD-R SHALL strictly follow GlobalPlatform Card Specification Amendment B [8] for the format of the POST request. The content of the HTTP POST header field X-Admin-From SHALL be filled with the “Agent Id” information standardised in GlobalPlatform Card Specification Amendment B [8], section “Administration Session Triggering Parameters” (the format of this field is not standardised).

“Agent Id” information SHALL include two parts:

      the eUICC identifier (EID)
      the identifier of the Security Domain representing the Admin Agent function
Each part is built using the following format:
          //<part-id>/<part-id-type>/<part-id-value>

Where:

-<part-id> is the tag that specifies which part is defined: “se-id” or “aa-id”

-<part-id-type> specifies the type of the identifier that is provided: “eid” or “aid”

-<part-id-value> provides the identifier value itself.

Format of the “X-Admin-From” field:

//se-id/eid/<EID>;//aa-id/aid/<RID ISD-R AID>/<PIX ISD-R AID>

Note that this representation of AID in the format /aid/<RID>/<PIX> is already used in GlobalPlatform for other purposes than the “Agent Id”.

Example of Agent Id field:

“//se-id/eid/89001012012341234012345678901224;//aa- id/aid/A000000559/1010FFFF8900000100” The eUICC SHALL use the Chunked mode [Transfer-Encoding: chunked CRLF] for the POST request message.

The SM-SR SHALL use Chunked mode [Transfer-Encoding: chunked CRLF] for the POST response.

First request sent by the ISD-R:

POST <initial uri> HTTP/1.1 CRLF Host: <SM-SR ip> CRLF X-Admin-Protocol: globalplatform-remote-admin/1.0 CRLF X-Admin-From://se-id/eid/<value>;//aa-id/aid/ <RID ISDR-AID >/<PIX ISDR-AID> CRLF CRLF

Return of a command response (no error case) sent by the ISD-R:

POST <uri contained in the previous POST response> HTTP/1.1 CRLF Host: <SM-SR ip> CRLF X-Admin-Protocol: globalplatform-remote-admin/1.0 CRLF X-Admin-From://se-id/eid/<value>;//aa-id/aid/ <RID ISDR-AID value>/<PIX ISDR-AID> CRLF Content-Type: application/vnd.globalplatform.card-content-mgt-response;version=1.0 CRLF Transfer-Encoding: chunked CRLF X-Admin-Script-Status: ok CRLF CRLF [response-string]

2.4.4.3 HTTP POST Response of SM-SR

The POST response is used by the SM-SR to transmit the next remote APDU format string to the ISD-R and possibly to provide the next URI that must be used to request th e following admin command.

The POST response SHALL strictly follow the GlobalPlatform Card Specification Amendment B [8].

POST response sent by the SM-SR containing commands that SHALL be executed by the ISD-R:

HTTP/1.1 200 CRLF X-Admin-Protocol: globalplatform-remote-admin/1.0 CRLF Content-Type : application/vnd.globalplatform.card-content-mgt;version=1.0 CRLF X-Admin-Next-URI: <uri of the next POST> CRLF CRLF [Command script]

POST response sent by the SM-SR containing commands that SHALL be executed by the ISD-P:

HTTP/1.1 200 CRLF X-Admin-Protocol: globalplatform-remote-admin/1.0 CRLF Content-Type : application/vnd.globalplatform.card-content-mgt;version=1.0 CRLF X-Admin-Next-URI: <uri of the next POST> CRLF X-Admin-Targeted-Application://aid/<rid>/<pix> (of the ISD-P-AID) CRLF CRLF [Command script]

Intermediate POST response sent by the SM-SR containing no command to execute but instructing to not close the HTTP session: the eUICC SHALL accordingly send a POST on the next URI provided, with no response body.

HTTP/1.1 204 CRLF X-Admin-Protocol: globalplatform-remote-admin/1.0 CRLF X-Admin-Next-URI: <uri of the next POST> CRLF CRLF

Last POST response sent by the SM-SR with nothing to do, communication SHALL be closed:

HTTP/1.1 204 CRLF X-Admin-Protocol: globalplatform-remote-admin/1.0 CRLF CRLF

2.4.4.4 Command Format in HTTP Message

The commands sent to the eUICC within a secure script in HTTP messages SHALL be formatted in an expanded remote command structure with indefinite length coding as defined in ETSI TS 102 226 [5]. As a consequence, the eUICC will provide the answer as an expanded remote response structure with indefinite length coding.

2.4.4.5 Sequence for HTTPS Session Triggering

Except if specified differently for a specific procedure, an HTTPS session with the eUICC is
always triggered by the SM-SR by sending a MT-SMS as defined in section 2.4.3.1.
                                                                                                  eUICC
            SM-SR                                                                                         ISD-R          ISD-P
                  (1) MT-SMS[<HTTP session triggering command>] SCP80
Failed
                      (2) Check SCP80 security

(3a) Conditional: DNS resolution to retrieve IP address of SM-SR

(3b) PSK-TLS handshake

POST <initial uri> HTTP/1.1 CRLF
Host: <SM-SR ip> CRLF                                                             (4)
X-Admin-Protocol: globalplatform-remote-admin/1.0 CRLF
X-Admin-From://se-id/eid/<value>;//aa-id/aid/ <RID ISDR-AID value>/<PIX
ISDR-AID> CRLF
 Figure 9: Sequence for HTTPS Session Triggering
(1) The SM-SR sends a MT-SMS to the ISD-R for HTTPS session triggering as defined in
      section 2.4.3.1.
(2) The ISD-R checks the security of the MT-SMS. The figure assumes the security is ok as
      defined in [13], otherwise section 2.4.3.1 applies.
(3) Opening of TLS socket
             a) If supported and if correctly configured by SM-SR and eUICC, the ISD-R MAY
                request a DNS resolution to retrieve the IP Address of the SM-SR. See section
                2.4.5
             b) The PSK-TLS handshake is performed as defined in [16] and [17]. The figure
                assumes the security is ok. In case of a temporary or fixable error, the SM-SR
                SHALL retry or fix the error.

(4) The first POST request is sent to the SM-SR as defined in section 2.4.4.2.

Then the SM-SR can continue with the procedure to execute.

2.4.5 DNS Resolution

DNS resolution is an optional feature that is triggered only when:

   The eUICC includes a DNS resolver Client configured to initiate the DNS queries to
    server
   The SM-SR relies upon a DNS Resolver Server able to provide the IP address
    associated to the domain name sent by the client query.
   The eUICC determines that it has to resolve the IP address of the SM-SR server

2.4.5.1 Criteria to determine whether DNS resolution is needed

If:

   the eUICC is requested to open an HTTPS session and
   the eUICC supports DNS resolution and
      the ISD-R has no IP address configured in the Connection Parameters of its
       Administration Session Triggering Parameters nor in the Administration Session
       Triggering SMS that may have triggered the session (as defined by Global Platform
       Amendment B [8]) and
      the ISD-R has a FQDN, and IP addresses of DNS servers, configured in DNS
       parameters as defined in section 4.1.1.10 and
      the ISD-R has not already resolved the FQDN to an IP address, or has resolved it but
       has reasons to consider the resolved value is stale

then the eUICC SHALL perform a DNS resolution as described in the procedure 2.4.5.3 to retrieve the IP address(es) of the SM-SR server. The eUICC MAY also support other heuristics to determine that DNS resolution is needed and to which DNS servers to send the DNS queries. For example it MAY obtain the IP addresses of DNS servers from the device as specified in ETSI TS 102 223 release 12.

2.4.5.2 DNS protocol features

The DNS resolver of SM-SR and eUICC SHALL:

      Be compliant to RFC 1035 and RFC 3596 defining the Domain Name System and
       protocol
      Support Query type A (IPv4) and AAAA (IPv6)
      Use UDP protocol
      Support only Recursive mode: the DNS resolver Server SHALL recursively resolve
       the given FQDN query, meaning that the answer SHALL contain all the available IP
       addresses
      Send short responses: any response returned by DNS Server must fit in one UDP
       packet

2.4.5.3 Procedure flow for DNS resolution

The sequence flow in the Figure 10 describes the basic exchange for DNS resolution

SM-SR / DNS                              Device                                    eUICC

(1) DNS resolution is requested

(2) OPEN CHANNEL UDP (parameters)

TR=OK

                                                                                                DNS resolution
                                                                           (3) DNS query        sequence may be
                                                                                                performed several
(4) Process DNS resolution                                                                      times

(5) DNS response

Figure 10: Sequence for Basic DNS resolution

(1) The eUICC determines that DNS resolution of SM-SR IP address is needed (as per section 2.4.5.1)

(2) if the device supports providing DNS IP addresses, the eUICC MAY obtain one or more
      IP addresses from the device; otherwise the eUICC SHALL use the IP addresses
      configured in the DNS parameters of the ISD-R’s SMSR addressing parameters (as
      defined in section 4.1.1.10)
         The eUICC opens an UDP channel to the DNS server
(3) The eUICC sends the DNS Query to the DNS Resolver Server
(4) The DNS Resolver Server of SM-SR processes this query, and retrieves the IP
      address(es) of the SM-SR server
(5) The DNS Resolver Server of the SM-SR send the DNS response including all the resolved
      IP addresses of the SM-SR server
      NOTE:      The eUICC MAY implement proprietary mechanisms to leverage more than
                 one IP addresses of DNS server, and more than one IP addresses of SM-
                 SR server, such as retry procedures, load balancing procedures. The
                 technical solution of these mechanisms is out of scope.

2.5 Communication on ES8 (SM-DP - eUICC)

The ES8 interface is between the SM-DP and its ISD-P and goes through the SM-SR.

The ES8 is realised by a SCP03 or SCP03t secure channel that is tunnelled through the secure channel between the SM-DP and the SM-SR (ES3) and on through into the SCP80 or SCP81 secure channel between the SM-SR and the ISD-R (ES5). It is then provided by the ISD-R to the ISD-P. This is shown in the Figure 6.

The eUICC SHALL support the Secure Channel Protocol 03 (SCP03) as defined in GlobalPlatform Card Specification Amendment D [10], as well as the variant SCP03t defined in this specification (see section 4.1.3.3), with:

   AES in CBC mode with key length of 128 bits, referred as AES-128
   Use of C-MAC, C-DECRYPTION R-MAC and R-ENCRYPTION for SCP03 (set in
    reference control parameter P1 of the EXTERNAL AUTHENTICATE command) and
    for SCP03t.
   Use of mode i=’70’, meaning use of pseudo-random card challenge, R-MAC and R-
    ENCRYPTION support

As a result the SM-DP and its ISD-P are mutually authenticated, all commands sent from the SM-DP to the ISD-P are signed and encrypted, and all responses sent by the ISD-P to the SM-DP are also signed and encrypted.

2.6 SM-DP to SM-SR Link Establishment (ES3)

The link between the SM-DP and the SM-SR (ES3) may have to be established during a procedure. For the “Profile Download and Installation” procedure, the Operator may ask to the SM-DP to contact an SM-SR that may be unknown to the SM-DP. The SM-DP will have to establish a connection with this new SM-SR.

It is assumed in this specification that:

   The Operator, requesting an action of an SM-DP through the ES2 interface, is able to
    provide the identification of the SM-SR in charge of the management of the eUICC
    targeted by the function.
   The SM-DP, based on the SM-SR identification provided through the ES2 interface, is
    able to retrieve the SM-SR address.
   The SM-DP, based on the SM-SR identification and address, is able to establish a
    new link to the identified SM-SR during any procedure requiring this step.

The procedure describing how the SM-DP establishes a link to the SM-SR (for example: business agreement or technical solution) is not covered by this specification.

2.7 OTA Platform Communication on ES6 (Operator-eUICC)

The ES6 is the interface between the Operator OTA Platform and a Profile inside an eUICC (see also section 2.2.5.3) through a secure channel as defined in ETSI TS 102 225 [4] and ETSI TS 102 226 [5]. This interface is the same as the one used with UICCs.

This specification recommends that OTA Platform communication on ES6 makes use of at least a minimum security settings defined for ES5 in section 2.4.

2.8 Communication on ES1 (EUM - SM-SR)

ES1 is the interface between the EUM and the first SM-SR that will manage the eUICC, to send to the SM-SR the EIS describing the eUICC or to update the EIS. The EIS contains the ISD-R keysets that SM-SR will use to secure the ES5 communication as described in section 2.4. Those keysets SHALL be protected by a mechanism agreed by the two parties. The agreement SHALL cover at least the following features. The default value specified SHALL be supported to ensure that an agreement can be reached:

   Ciphering algorithm: by default, AES transport key of size 128 bits (as per section
    2.3.3)
   Key sizes (of transported keys), at least as per section 2.3.3
   Padding: no padding if then length of the key being ciphered is already aligned with
    the AES block size, otherwise PKCS#7
   Cipher mode: ECB

2.9 Compliance

The elements of the ecosystem (SM-DP, SM-SR and eUICC) SHALL be certified according to section 5 of the GSMA Remote Provisioning Architecture for Embedded UICC [1]. SM-SR, SM-DP and eUICC SHALL be compliant with SGP.16 [64].

3 Detailed Procedure Specifications

This section contains the detailed specifications of the procedures that realise the Remote Provisioning and Management system for the eUICC.

The order of sending or reception of the responses of the functions and notifications defined across this procedures section MAY differ from it in the real implementations.

3.1 Profile Download and Installation

The Profile Download and Installation procedure is sub-divided into four main steps:

      1.   ISD-P creation on the eUICC
      2.   Personalization of the ISD-P with a first key set, called the key establishment procedure
      3.   Download and installation of the Profile onto the eUICC
      4.   Optional: Enabling of the newly installed Profile.
Optionally the SM-SR MAY send a command ES5.UpdateSMSRAddressingParameters to update the
list of TP-DestinationAddress and define a specific TP-DA for this newly loaded Profile. The command
can be sent anytime after step 1 (ISD-P creation) but before step 4 (enabling of the Profile).

3.1.1 ISD-P Creation

The next figure describes the call flow for the first step which is the ISD-P creation. The procedure illustrates the usage of RAM over HTTP as an example of the transport protocol, assuming that the sequence will be followed by a key establishment procedure and the full download of the Profile.

NOTE:CAT_TP could be used as transport protocol and would have an equivalent procedure.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 160 hide footbox

participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox

OP->>DP: (1) downloadProfile(srid, eid, iccid, final state, profileType) DP->SR: (2) getEIS(eid)

Rnote over SR #FFFFF (3) Retrieve EIS Endrnote

SR-->DP: Failed DP-->>OP:

SR-->DP: (4) Return EIS

Rnote over DP #FFFFFF (5) Check eUICC eligibility Endrnote DP-->>OP: Failed

DP->>SR: (6) createISDP(eid, iccid, mno -id,…)

Rnote over SR #FFFFFF (7) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP:

Hnote over SR, ISDR #C0C0C0 HTTPS session opening Endhnote

SR->>ISDR: (9) note over SR, ISDR **HTTP/1.1 200 CRLF** Headers CRLF <Body with ES5.createISD-P function> End note

ISDR->ISDP: (10) New                  .

ISDR->>SR: (11) note over SR, ISDR **POST /<next-uri> HTTP/1.1 CRLF** Headers X-Admin-Script-Status: <script-status> CRLF CRLF <Body with ES5.createISD-P response> End note

Rnote over SR #FFFFFF (12) EIS update

Endrnote

SR->>DP: (13) create ISDP function response @enduml

Figure 11: ISD-P creation

Start Conditions:

The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:
(1) The Operator owning the Profile to download SHALL call the “ES2.DownloadProfile”
   function with its relevant input data (the Operator has to provide the SM-SR identification
   and address). By providing the required final state, the Operator MAY ask the SM-DP to
   enable the newly downloaded Profile at the end of the procedure. Else, by default, the
   Profile will be in the DISABLED state.
(2) The SM-DP on reception of this request SHALL call the “ES3.GetEIS” function with its
   relevant input data.
(3) The SM-SR SHALL retrieve the EIS of the eUICC based on the EID. At this stage the SM-
   SR MAY return an error indicating that the eUICC is unknown in its system. The error
   SHALL be finally returned to the Operator and the procedure SHALL end.
(4) The SM-SR SHALL return the EIS of the eUICC.
           a. In case the EIS indicates an ISD-P in state 'Created' with the 'smdp-id'
              associating it to the calling SM-DP, the SM-DP SHALL delete this Profile,
              whether it has the same or a different ICCID, as described in section 3.1.5
              before attempting to install a new Profile.
(5) The SM-DP SHALL check the eligibility of the eUICC against the characteristics of the
   Profile to be downloaded. Although the exact checks performed by the SM-DP are out of
   scope for this specification, some examples might include:
           a. Is the target Profile compatible with and validated against this type of eUICC?
              (including the fact that the SM-DP is able to generate the Profile for this type
              of eUICC).
b. Is there enough memory? In case of uncertainty of the information contained
   within the EIS, the SM-DP could request an online audit.
c. Is the eUICC certified? In case of a non-certified eUICC, the SM-DP MAY
   stop the procedure.

The SM-DP SHALL verify the ECASD certificate, which was received as part of the EIS, using the EUM Certificate and the CI’s Root Certificate and SHALL extract PK.ECASD.ECKA from the ECASD certificate. If any of these conditions is not satisfied or if the certificate verification fails, the SM-DP SHALL return a response indicating a failure. (6) The SM-DP SHALL call the “ES3.CreateISDP” function with its relevant input data. (7) The SM-SR SHALL verify that the SM-DP request is acceptable (the verifications that the SM-SR SHALL perform are described in the section 5.4.3). If any of the conditions to be verified are not satisfied, the SM-SR SHALL return a response indicating a failure, and the procedure SHALL stop. Otherwise the SM-SR, SHALL create a new Profile entry for the EIS having a state “In- Creation”. The Profile with this state SHALL NOT appear in the EIS returned on ES3.GetEIS and ES4.GetEIS

(8) If there is no existing HTTPS session with the eUICC, the SM-SR SHALL trigger the
   HTTPS session as defined in section 2.4.4.5.
(9) The SM-SR SHALL return the HTTP POST response containing the “ ES5.CreateISDP”
   with its relevant input data. The X-Admin-Targeted-Application parameter SHALL be
   omitted as the command is targeting the ISD-R.
(10)   The ISD-R SHALL create the ISD-P. In case of an error, the ISD-R SHALL return the
   error within the next POST request to the SM-SR. The SM-SR SHALL delete the new
   Profile entry having the state “In-Creation“ from the EIS. The error SHALL be finally
   returned to the SM-DP and the procedure MAY end depending on the error.
(11)   The eUICC SHALL return the “ES5.CreateISDP” function execution response within
   the POST request to the SM-SR.
(12)  Assuming a successful ISD-P creation, the SM-SR SHALL update the state of the
   Profile in the EIS to “Created“.
(13)  The SM-SR SHALL return to the SM-DP the “ES3.CreateISDP” function execution
   response.
(13a) In case the SM-SR does not receive a function execution response from the eUICC
      (e.g. due to a disrupted connection), the SM-SR SHALL trigger ES5.DeleteISDP
      function on the targeted ISD-P and update the EIS by removing the new Profile entry
      with status "In Creation" from the EIS accordingly.

In this sample procedure, it is assumed that the SM-DP has indicated “more to do” in the “ES5.CreateISDP” call. In case the SM-DP did not indicate “more to do”, the SM-SR MAY end the HTTPS session.

3.1.2 Key Establishment with Scenario#3-Mutual Authentication

The next figure describes the second step in the Profile Download and Installation procedure.

This sequence defines a new scenario called “Scenario#3-Mutual Authentication”. This sequence uses Scenario#3 based on ECKA EG (ElGamal) scheme as defined in GlobalPlatform Card Specification Amendment E [11] complemented by an SM-DP authentication step.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 160

hide footbox

participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF participant ECASD #FFFFFF endbox

DP->>SR: (1) sendData(eid, sd-aid, ES8.EstablishISDPKeySet(CERT.DP.ECDSA)) Rnote over SR (2) Check initial conditions End rnote

SR-->>DP: Failed DP-->>OP:

Hnote over SR, ISDR #C0C0C0 (2a) Conditional: HTTPS Session opening Endhnote

SR->>ISDR: (3) note over SR, ISDR **HTTP/1.1 200 CRLF** … CRLF <Body with ES8.EstablishISDPKeySet(CERT.DP.ECDSA)> End note

ISDR->ISDP: (3a) CERT.DP.ECDSA

rnote over ISDP (3b) Verifies that it is an SM-DP certificate End rnote

ISDP->ECASD: (4) CERT.DP.ECDSA

Rnote over ECASD 5) verifies CERT.DP.ECDSA using PK.CI.ECDSA. Continue if successful: - extracts PK.DP.ECDSA from CERT.DP.ECDSA. - generates RC End rnote ECASD-->ISDP:(6) RC or error ISDP-->ISDR: (7)

ISDR->>SR: note over SR, ISDR **POST /<next-uri> HTTP/1.1 CRLF** … **X-Admin-Script-Status:** <script-status> CRLF CRLF <Body with ES8.EstablishISDPKeySet response: RC or error>

End note

SR->>DP:(8) sendData response with ES8.EstablishISDPKeySet response: RC or error

Hnote over OP, ISDP #C0C0C0 (8a) Conditional: Error manageent, see 3.1.4 Endhnote

rnote right of OP (9) Generates (eSK.DP.ECKA, ePK.DP.ECKA) Signs RC and ePK.DP.ECKA with SK.DP.ECDSA End rnote

DP->>SR: (10) sendData( eid, sd-aid, ES8.keyEstablishISDPKeySet(ePK.DP.ECKA, signature)) SR->>ISDR: (11) Note over SR **HTTP/1.1 200 CRLF** … CRLF <Body with ES8.EstablishISDPKeySet(ePK.DP.ECKA, RC, signature)> End note

ISDR->ISDP:(12) ePK.DP.ECKA, signature ISDP->ECASD rnote over ECASD 13) verifies signature using PK.DP.ECDSA. Continue if successful: - calculates ShS from ePK.DP.ECKA and SK.ECASD.ECKA. End rnote

ECASD-->ISDP: (14) ShS or error

rnote over ISDP (15) (Opt.) Generates DR Derives keyset from ShS (and DR) Calculates receipt. End rnote

ISDP-->ISDR: (16) Receipt (Opt. DR) or error

ISDR->>SR:(17) Note over SR, ISDR **POST** /<next-uri> **HTTP/1.1** CRLF … **X-Admin-Script-Status:** <script-status> CRLF CRLF <Body with ES8.EstablishISDPKeySet response: Receipt (Opt. DR) or error> End note

SR->>DP:(18) sendData response with ES8.keyEstablishISDPKeySet response: Receipt (Opt. DR) or error

hnote over OP, ISDP #C0C0C0 (18a) Conditional: Error management see 3.1.4 end hnote

rnote right of OP (19) Calculates ShS from eSK.DP.ECKA and PK.ECASD.ECKA. Derives keyset from ShS (and DR) Verifies receipt End rnote

@enduml

Figure 12: Key Establishment, Scenario #3

Start Conditions: As a pre-condition, the ISD-P SHALL be created as defined in section 3.1.1, the eUICC/ECASD SHALL support the scenario#3-Mutual Authentication and SHALL be provisioned with the SK.ECASD.ECKA, PK.CI.ECDSA.

Procedure:
(1) The SM-DP SHALL call the “ES3.SendData” function specifying the targeted eUICC, the
   ISD-R, and the data containing the “ES8.EstablishISDPKeySet” function with the
   certificate identifying the SM-DP. The certificate SHALL be issued by the SM-DP
   Certificate Issuer.
(2) The SM-SR SHALL verify that the SM-DP request is acceptable (the verifications that the
   SM-SR SHALL perform are described in the section 5.4.4).
       If any of the conditions to be verified are not satisfied, the SM-SR SHALL return a
       response indicating a failure, and the procedure SHALL stop.
       (2a)   The SM-SR SHALL trigger the HTTPS session with the ISD-R if not already
              opened as defined in section 2.4.4.5.
(3) The SM-SR SHALL return the HTTP POST response with a body containing the
   “ES8.EstablishISDPKeySet” function as provided by the SM-DP in (1). The X-Admin-
   Targeted-Application parameter SHALL be omitted as the command is targeting the ISD-
   R
       (3a)   The ISD-R SHALL forward the content of the STORE DATA command contained
              in the HTTP response to the ISD-P.
       (3b)   The ISD-P SHALL verify that it is an SM-DP certificate.
(4) The ISD-P SHALL forward the CERT.DP.ECDSA to the ECASD for verification.
(5) ECASD SHALL verify the provided CERT.DP.ECDSA with the PK.CI.ECDSA; if
   CERT.DP.ECDSA is valid, ECASD SHALL extract and store the PK.DP.ECDSA and
   generate a random challenge (RC). The length of the Random Challenge SHALL 16 or 32
(6) The Random Challenge (or error if any) SHALL be returned to the ISD-P which forwards
   it to the ISD-R.
(7) The ISD-R SHALL return the execution response (RC or error) within a new HTTP POST
   request addressed to the SM-SR.
(8) The SM-SR SHALL return the content of the received HTTP POST (RC or error) to the
   SM-DP.
       (8a)   In case of failure during the key establishment procedure, error management
              procedure describes in section 3.1.4 SHALL be executed and the procedure
              SHALL stop.
(9) The SM-DP SHALL generate an ephemeral key pair (related to the targeted ICCID), called
   ePK.DP.ECKA and eSK.DP.ECKA. The SM-DP signs the received Random
   Challenge(RC) and the generated ePK.DP.ECKA with the SK.DP.ECDSA.
(10)  The SM-DP SHALL call the “ES3.SendData” function specifying the targeted eUICC,
   the ISD-R and the data containing the “ES8.EstablishISDPKeySet” function with the
   ePK.DP.ECKA and the previously computed signature on Random Challenge (RC) and
   ePK.DP.ECKA using SK.DP.ECDSA.
(11)  The SM-SR SHALL return the HTTP POST response with a body containing the
   “ES8.EstablishISDPKeySet” function as provided by the SM-DP in (10). The X-Admin-
   Targeted-Application parameter SHALL be omitted as the command is targeting the ISD-
   R.
(12)   The ISD-P SHALL forward the content of the STORE DATA command, containing the
   ePK.DP.ECKA and signature to the ISD-P, which SHALL forward them to the ECASD for
   verification.
(13)   The ECASD SHALL verify the signature using the previously stored PK.DP.ECDSA. If
   the signature is not verified, an error SHALL be returned. Else the ECASD SHALL
   calculate the ShS using the ePK.DP.ECKA and the SK.ECASD.ECKA.
(14)        The ShS or an error SHALL be returned to the ISD-P.
(15)   The ISD-P:
      MAY optionally compute a Derivation Random (DR, if requested by the SM-DP in
         the function call).
      Derives the key set from ShS (and optionally DR).
      Calculates the receipt to be returned to SM-DP.
      In case of error at this step, the length of the returned receipt SHALL be 0.
(16) The ISD-P SHALL return the calculated receipt (and optionally the DR) or the error to
   the ISD-R.
(17)   The ISD-R SHALL return the execution response to the ISD-P (receipt (opt. DR) or
   error) within a new HTTP POST request addressed to the SM-SR.
(18)   The SM-SR SHALL return the content of the received HTTP POST (receipt (opt. DR)
   or error) to the SM-DP.
        (18a) In case of failure during the Key Establishment procedure, the error management
              procedure described in section 3.1.4 SHALL be executed and the procedure
              SHALL stop.
(19)   The SM-DP symmetrically SHALL:
         Calculate the ShS using the eSK.DP.ECKA and the PK.ECASD.ECKA,
         Derive the key set from ShS (and optionally DR), and
         Verify the receipt received in the response to ensure that key set derivation is
          consistent with what has been performed by the ISD-P.
The eUICC SHALL support key establishment with and without the DR. The SM-DP decides
which option to use.

BSI TR-03111 [49] contains recommendations and requirements on the generation and validation of ephemeral keys. In addition, NIST SP 800-56A [50] provides requirements on the destruction of ephemeral keys and other intermediate secret data after the ir use.

3.1.3 Download and Installation of the Profile

This section describes the third part of the procedure for the Profile Download and Installation step. The procedure illustrates the usage of RAM over HTTP as an example of the transport protocol.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 160 hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox

DP->SR: (1) sendData(eid, isd-p-aid, [<data1>]<sub>scp03t</sub>, moreTodo) Rnote over SR #FFFFF (2) Check initial conditions Endrnote

Hnote over SR, ISDR #C0C0C0 (2b) Conditional: HTTPS session opening End hnote

SR->>ISDR: (3) note over SR,ISDR **HTTP/1.1 200 CRLF** … **X-Admin-Targeted-Application:**//aid/<rid>/<pix> (of ISD-P-AID)CRLF CRLF <Body with [<data1>]<sub>scp03t</sub> > End note

ISDR->ISDP: (4) rnote over ISDP (5) Unwrap SCP03t security End rnote

rnote over ISDP (6) Process Profile data End rnote

ISDP-->ISDR: (6a) ISDR->>SR: (7)

Note left of ISDP **POST** /<next-uri> **HTTP/1.1** CRLF … **X-Admin-Script-Status:** <script-status> CRLF CRLF <Body with [data1 execution response] <sub>scp03t</sub> > End note

SR->>DP: (8) SendData response + [data1 execution response]<sub> scp03t</sub> Hnote over DP, ISDP #C0C0C0 (9) Optional: new data sending End hnote

Hnote over OP, ISDP #C0C0C0 (9a) Conditional: Error management see 3.1.4 End hnote

DP->SR: (10) profileDownloadCompleted(eid, iccid, subdAddress, POL2)

rnote over SR (11) Update EIS End rnote

SR-->DP

Hnote over SR, ISDP #C0C0C0 (12) Optional: : Enable Profile see 3.3 End hnote

DP->>OP: (13) Profile download &installation success SR->>M2MSP: (14) Cond: HandleProfileDownloadedNotification (eid, iccid, enabled)

@enduml

Figure 13: Download and Installation of the Profile

Start Conditions: As a pre-condition, the ISD-P SHALL be created and personalized as defined in section 3.1.1 and section 3.1.2.

Procedure:
(1) The SM-DP SHALL call the “ES3.SendData” function specifying the targeted eUICC, the
   ISD-P, and providing the Profile data to download as input data. The Profile data has to
   be given as specified in section 4.1.3.1 and 5.4.4.
(2) The SM-SR SHALL verify that the SM-DP request is acceptable (the verifications that the
   SM-SR SHALL perform are described in section 5.4.4).
(2a)    Depending on the error, the procedure MAY stop and a global failure message SHALL
        be returned to the Operator.
(2b)    The SM-SR SHALL trigger the HTTPS session opening with the ISD-R if not already
        opened, as defined in section 2.4.4.5.
(3) The SM-SR SHALL return the HTTP POST response containing the secure data as
   provided by the SM-DP. The X-Admin-Targeted-Application field SHALL contain the ISD-
   P-AID.
(4) The ISD-R SHALL forward the received secure data to the ISD-P identified by the X-
   Admin-Targeted-Application field.
(5) The ISD-P SHALL process the security of the received data. The figure illustrates a
   success case; in case of security failure the error SHALL be returned within the next POST
   request to the SM-SR and finally returned to the SM-DP; and the procedure MAY end
   depending on the error.
(6) The ISD-P SHALL process the received command TLV(s).
       (6a)    The ISD-P SHALL return the response to the command TLV(s) to the ISD-R.
(7) The ISD-R SHALL return the ISD-P’s response within the next POST request to the SM-
   SR.
(8) The SM-SR SHALL return to the SM-DP the execution status of the “ES3.SendData”
   function.
(9) Optionally the SM-DP MAY call the same “ES3.SendData” function again if the download
   and installation of the Profile requires several steps. This optional step MAY be repeated
   as many times as required.
(9a)    In case of failure during the Download and Installation procedure, the SM-DP SHALL
        execute the error management procedure described in section 3.1.4. If this error
        management procedure fails to delete the ISD-P because the POL1 of the Profile
        prevented the deletion, the SM-DP shall consider that the profile installation succeeded
        on the eUICC, and SHALL continue at step 10 below. Otherwise the SM-DP SHALL
        return the result as specified in section 3.1.4 and the procedure SHALL stop.
(10)   When Profile download is completed the SM-DP SHALL call the
   “ES3.ProfileDownloadCompleted” function. This basically indicates to the SM-SR that
   the Profile is downloaded and installed. The SM-DP MAY take the opportunity to define a
   POL2 on the Profile. The Operator SHALL be able to specify the POL2 content even if it
   is empty.
   As requested by the Operator, after Profile installation the SCP03 key set of the ISD -P
   MAY:
i.   Be retained by the SM-DP. In this case the Operator can instruct the SM-DP to
     hand over or delete the key set at a later point in time;
ii. Be handed over to the Operator. The keys MAY be replaced by the Operator;
iii. Be deleted from the eUICC by the SM-DP (using the GlobalPlatform DELETE
     command).
(11)  The SM-SR SHALL update the EIS reflecting that the Profile is in “DISABLED” state,
   and POL2 if present.
(12)   If the Operator has initially requested the Profile to be enabled, the SM-DP SHALL
   request the SM-SR to enable the newly installed Profile following the procedure in section
   3.3 with the following modifications:
   The procedure SHALL start with step (1)
For the Normal Case, described in section 3.3.1 the following modification SHALL
apply:
   The SM-DP SHALL NOT perform step 17
For the Failure Case, described in section 3.3.2 the following modification SHALL apply:
 The SM-DP SHALL NOT perform step (14)
NOTE          When a M2M SP has a PLMA set to receive “Profile Download
              Notifications”, as described in section 5.7.1, it has to be considered that the
              M2M SP may receive the information of a successful Profile download,
              based on a notification sent by the SM-SR, earlier than the Operator who
              has initiated the Profile Download. The Operator does not receive the result
              of a Profile download until the Profile Enable procedure, as described in
              section 3.3, has been executed. The result of Profile Download, including
              the result of Profile Enabling, is sent as described by step (13) of this
              procedure.
(13)   The SM-DP SHALL return the response to the “ES2.DownloadProfile” function call to
   the Operator. In case the Profile has been downloaded successfully but the optional step
   12 failed or expired before completion of the Profile enabling, the function execution
   response SHALL include the execution status “Executed-WithWarning” indicating that the
   Profile has been downloaded.
(14)  If the profile has been successfully downloaded and installed, the SM-SR SHALL send
   the “ES4.HandleProfileDownloadedNotification” to a M2M SP, if authorised by the
   Operator owning the Profile, and SHALL indicate if the profile has been enabled as
   described in the optional step 12.
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   the Operator owning the Profile, the SM-SR SHALL send this notification to this other
   Operator by calling the “ES4.HandleProfileDownloadedNotification”.
   If the M2M SP is another Operator connected through its SM-DP and it is authorised by
   the Operator owning the Profile, the SM-SR SHALL send this notification to the SM-DP
   associated       to      this       other    Operator       by        calling     the
   “ES3.HandleProfileDownloadedNotification”.

Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting as the M2M SP, by calling the “ES2.HandleProfileDownloadedNotification”.

At the end of this procedure, if the Profile has been enabled, the Operator owning of the Profile is able to perform any remote management operation to the Profile using its own Remote Administration Server.

3.1.4 Error Management Sub-Routine

The next figure describes the flow for error management. This procedure is called when an error occurs during the key-establishment procedure or during the steps 1 to 11 of the Profile Download and Installation procedure (before the optional enabling of the Profile). The procedure illustrates the usage of RAM over HTTP as an example of the transport protocol.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 160 hide footbox

participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF participant ECASD #FFFFFF endbox

DP->>SR: (1) In case of failure, deleteIS DP(iccid) function

Hnote over SR, ISDR #C0C0C0 (1a) Conditional: HTTPS session opening end hnote

SR->>ISDR: (2) Note left of ISDP **HTTP/1.1 200** CRLF … CRLF <Body with ES5.DeleteProfile(isd-p-aid)> End note

Rnote over ISDR #FFFFFF (3) Enforce POL1 Endrnote |||

Alt Unless POL1 rejects deletion Rnote over ISDR: (4) Delete ISD-P End

ISDR->>SR: (5) Note left of ISDP **POST** /<next-uri> **HTTP/1.1** CRLF … **X-Admin-Script-Status:** <script-status> CRLF CRLF <Body with ES5.DeleteProfile response > End note

SR->>DP: (6) ISD-P deletion result

Alt Deletion failed due to POL1
Hnote over OP, SR #C0C0C0
(7a) Complete Download and Installation
     procedure, see 3.1.3
End hnote

Else Otherwise DP->>OP: (7) Download failed End

@end uml

Figure 14: Error Management Sub-Routine

Procedure: (1) In case of failure during the key establishment procedure or the Download Profile procedure, the SM-DP SHALL call the “ES3.DeleteISDP” function with its relevant input data.

(1a)    The SM-SR SHALL trigger the HTTP session with the ISD-R if not already opened as
        defined in section 2.4.4.5.
(2) The SM-SR SHALL return the HTTP POST response with a body containing the
   “ES5.DeleteProfile” function with the ICCID. The X-Admin-Targeted-Application
   parameter SHALL be omitted as the command is targeting the ISD-R.
(3) If the Profile is already completely installed, the ISD-R SHALL enforce POL1. If POL1
   prevents the deletion of the target Profile, the ISD-R SHALL skip step 4.
(4) The ISD-R SHALL delete the targeted ISD-P.
(5) The ISD-R SHALL        return the execution response to the ISD-P deletion
   “ES5.DeleteProfile” within a new HTTP POST request addressed to the SM-SR.
(6) The SM-SR SHALL forward the status of the “ES3.DeleteISDP”to the SM-DP.
(7) If the deletion of the ISD-P was successful, the response message indicating the failure of
   the download SHALL be returned to the Operator. In case of a timeout of the
   “ES5.DeleteProfile”, the status of the download SHALL be reported as ‘Expired’.
           a. If the deletion of the ISD-P was prevented by POL1, the SM-DP shall consider
              that the profile download and installation succeeded on the eUICC, and SHALL
              continue the procedure 3.1.3.

NOTE:In case the deletion of the ISD-P fails or expires (e.g. because the eUICC is out of coverage), or in case the SM-DP does not receive confirmation of the deletion (e.g. because sending the result (5) failed), the SM-DP will get a chance to delete the ISD-P and the potentially incomplete profile at the beginning of a subsequent Profile Download on the same eUICC, as described in section 3.1.5.

3.1.5 ISD-P Cleanup Sub-Routine

The next figure describes the alternate flow that an SM-DP SHALL follow to delete an ISD-P that it formerly failed to delete.

NOTE 1:The case where a Cleanup fails due to POL1 is not covered here.

NOTE 2:The case where a Profile with the same ICCID was incompletely downloaded to a different eUICC is not covered here.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 160 hide footbox

participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox

OP->>DP: (1) downloadProfile(srid, eid, iccid, final state, profileType) DP->SR: (2) getEIS(eid)

Rnote over SR #FFFFF (3) Retrieve EIS Endrnote

SR-->DP: (4) Return EIS

Alt [If the SM-DP detects an ISD-P that it created and still in an incomplete state]

DP->>SR: (5alt) DeleteProfile(eid, iccid) Rnote over SR #FFFFF (6alt) Check initial conditions Endrnote SR-->>DP: Failed SR->>ISDR: (7alt) MT-SMS [ES5.DELETE command]SCP80

Rnote over ISDR #FFFFFF (8alt) Delete ISD-P Endrnote

ISDR-->>SR: (9alt) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (10alt) Update EIS Endrnote SR-->>DP: (11alt) Profile deletion result

End

Rnote over DP #FFFFFF (5) Check eUICC eligibility Endrnote DP-->>OP: Failed

DP->>SR: (6) createISDP(eid, iccid, mno -id,…)

@enduml

Figure 315-A: ISD-P cleanup at the beginning of a subsequent profile download

Procedure: (1) 2) (3) (4) See section 3.1.1.

(5alt) As per the EIS, or by comparing the EIS with its own records, the SM-DP determines that an ISD-P associated to this SM-DP is in an incomplete state (the profile download procedure did not complete nominally). The SM-DP SHALL then send a request “ES3.DeleteISDP” to the SM-SR to delete the incomplete ISD-P.

(6alt) The SM-SR SHALL verify if the SM-DP request is acceptable (the verifications that the
       SM-SR SHALL perform are described in section5.4.9). If any of the conditions to be
       verified are not satisfied, the SM-SR SHALL return a response indicating a failure, and
       the procedure SHALL end.
(7alt) The SM-SR SHALL send an MT-SMS containing the “ES5.DELETE” command with
       its relevant input data (see section 4.1.1.4) to the ISD-R. The SM-SR SHALL request
       a PoR to get the execution status of the “ES5.DELETE” command.

(8alt) The ISD-R SHALL delete the targeted ISD-P and the contained Profile.

(9alt) The ISD-R SHALL return the MO-SMS to the SM-SR containing the execution status
       of the “ES5.DELETE” command.
(10alt)In case of successful execution, the SM-SR SHALL update the EIS to reflect the
       newly deleted Profile.
(11alt) The SM-SR SHALL return the response to the “ES3.DeleteISDP” function to the SM-
       DP.

(5)(6)… The SM-DP and SM-SR SHALL resume the procedure described in section 3.1.1

3.2 Profile Enabling

The Profile Enabling procedure between the Operator and the SM-SR is used to enable a Profile previously downloaded and installed on an eUICC (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.5). The procedure is initiated by the Operator owning the Profile to be enabled. The procedure illustrates the usage of SMS as a possible transport protocol between SM-SR and eUICC, but can also be performed using other transport protocols.

3.2.1 Normal Case

The sequence flow in the Figure 15 describes the normal case where the target Profile can successfully be enabled.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox

OP1->>SR: (1) EnableProfile(eid, iccid)
Rnote over SR #FFFFF
(2) Check initial conditions
Endrnote
SR-->>OP1: Failed
SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80
Rnote over ISDR #FFFFFF
(4) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80
SR-->>OP1: Failed
Rnote over ISDR #FFFFFF
(5) Enable ISD-P
Endrnote
ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80
SR-->>OP1: (6a) Failed
ISDR-->>DEV: (7) REFRESH, (UICC reset)
Rnote over DEV, ISDR #FFFFFF
(8) Network attachment with the enabled profile
Endrnote
|||
Hnote right of SR #FFFFFF
(9)                  Notification procedure over SMS
Endhnote
|||
Rnote over SR #FFFFFF
(10) Check POL2
Endrnote
SR->>ISDR: (11) Cond.: MT-SMS [ES5.DELETE command]SCP80
Rnote over ISDR #FFFFFF
(11a) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.DELETE command FAILED response]SCP80
SR-->>OP1: Failed
Rnote over ISDR #FFFFFF
(11b) Delete disabled ISD-P
and contained profile
Endrnote
ISDR-->>SR: (11c) MO-SMS [ES5.DELETE command response]SCP80
Rnote over SR #FFFFFF
(12) Update EIS
Endrnote
SR-->>OP1: (13) Profile enabling result
SR->>OP2: (14) HandleProfileDisabledNotification(eid, iccid2)
SR->>M2MSP: (15) HandleProfileEnabledNotification (eid, iccid)
SR->>M2MSP: (16) HandleProfileDisabledNotification (eid, iccid2)

@enduml

Figure 15: Profile Enabling, Success Case

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure: (1) Operator1, of the target Profile SHALL call the “ES4.EnableProfile” function with its relevant input data. (2) The SM-SR SHALL verify that the Operator1 request is acceptable (the verifications that the SM-SR SHALL perform are described in the section 5.5.5), and in particular evaluates POL2 of the currently Enabled Profile. If any of the conditions to be verified are not satisfied, the SM-SR SHALL return a response indicating the failure, and the procedure SHALL end. (3) The SM-SR SHALL send an MT-SMS containing the “ES5.STORE DATA” command for Profile enabling with its relevant input data (see section 4.1.1.2) to the ISD-R. The SM-SR SHALL request a PoR to get the execution status of the “ ES5.STORE DATA” command. (4) The ISD-R SHALL enforce POL1 of the currently Enabled Profile. If POL1 rejects enabling of the target Profile, the ISD-R SHALL return directly the MO-SMS containing the response indicating a failure, and the procedure SHALL end.

(5) If POL1 allows, the ISD-R SHALL disable the currently enabled ISD-P and enable the
   targeted ISD-P.
   NOTE:        Profile change includes a change of the IMSI that is used to attach to the
                network. As indicated in 3GPP TS 31.102 [52], such a change requires special
                caution and should always be accompanied by a REFRESH command to
                avoid inconsistent information being read by the terminal. So while the
                targeted ISD-P is marked as enabled in this step, it MAY actually become
                effective after the terminal executes the REFRESH command.
(6) The ISD-R SHALL return the MO-SMS containing the execution status of the “ES5.STORE
   DATA” command to the SM-SR.
(6a)   If the response to the “ES5.STORE DATA” command indicates a failure, the SM-SR
       SHALL return a response indicating the failure to Operator1, and the procedure SHALL
       end.
(7) The ISD-R SHALL send a REFRESH proactive command in UICC reset mode to the
    Device. This will trigger the execution of a network attach procedure.
   NOTE:        In case of any error after this step, indicating that the currently Enabled
                Profile cannot provide connectivity, the ISD-R SHALL re-enable the
                previously Enabled Profile as described in section 3.2.2.
(8) The eUICC and the Device SHALL perform a network attach procedure with the newly
   Enabled Profile.
(9) The eUICC SHALL perform the notification procedure as described in section 4.1.1.11.
   During this procedure, if the ISD-R doesn’t succeed in sending the SMS notification (after
   having exhausted all possible retries), or doesn’t receive the SM-SR notification
   confirmation, this SHALL be considered as a fatal error, and the previo us note SHALL
   apply. On reception of the SM-SR notification confirmation command, if POL1 of the now
   Disabled Profile contains the rule “Profile deletion is mandatory when it is disabled”, and
   this Profile does not have the Fall-Back Attribute set, the ISD-R SHALL delete the disabled
   ISD-P and the contained Profile. The eUICC SHALL send the response to the notification
   confirmation indicating whether the disabled ISD-P has been deleted or not.
(9a)   If the previously Enabled Profile (now Disabled) has the Fall-Back Attribute, and its
       POL1 contains the rule “Profile deletion is mandatory when its state is changed to
       disabled”, this rule SHALL be ignored according to Sections 2.4 and 3.6.3.2 in GSMA
       Remote Provisioning Architecture for the Embedded UICC [1], and the procedure
       SHALL continue at step 10.
(10)   On reception of the “ES5.HandleNotificationConfirmation” response, and if this
   response indicates that the Disabled Profile has not been deleted, the SM-SR SHALL
   evaluate POL2 of the Disabled Profile. If POL2 of the Disabled Profile contains the rule
   “Profile deletion is mandatory when it is disabled”, the SM-SR SHALL perform step (11),
   else it SHALL jump to step (12).
(11)    The SM-SR SHALL send an MT-SMS containing the “ES5.DELETE” command with
   its relevant input data (see section 4.1.1.4) to the ISD-R, targeting the Disabled Profile.
   The SM-SR SHALL request a PoR to get the execution status of the “ ES5.DELETE”
   command.
(11a) The ISD-R SHALL enforce POL1 of the target Profile. If POL1 rejects the deletion of
      the target Profile, the ISD-R SHALL return the MO-SMS containing the response
      indicating the corresponding failure, and the procedure SHALL end.
(11b) If POL1 allows its deletion, the ISD-R SHALL delete the targeted ISD-P and the
      contained Profile.
(11c) The ISD-R SHALL return the MO-SMS to the SM-SR containing the execution status
      of the “ES5.DELETE” command.
(12)  According to the executed sequence and the eUICC responses, the SM-SR SHALL
   update the EIS to reflect that:
      The target Profile has been enabled
      The previously Enabled Profile has been disabled or deleted.
   NOTE:        POL1 and POL2 MAY have different content. As a consequence, both the
                eUICC and the SM-SR have to ensure the ISD-P deletion based on their
                respective Policy.
(13) The SM-SR SHALL return the response to the “ES4.EnableProfile” function to
   Operator1, indicating that the Profile has been enabled.
(14)    Unless Operator2 has set an ONC (Operator Notifications Configuration) to not receive
   those         notifications,       the        SM-SR        SHALL         send          the
   “ES4.HandleProfileDisabledNotification” or “ES4.HandleProfileDeletedNotification”
   (if deletion was triggered by the evaluation of POL1 and POL2) to Operator2, the owner of
   the Profile that was enabled at the beginning of the procedure. In case Operator2 has no
   direct connection with the SM-SR (SM-SR SHALL be able to detect such a situation based
   on its own database), the SM-SR SHALL send this notification to the SM-DP authorised
   by Operator2 by calling the “ES3.HandleProfileDisabledNotification” or the
   “ES3.HandleProfileDeletedNotification”. The SM-SR can retrieve the SM-DP identity
   based on the EIS content. Then the SM-DP, on reception of this notification, SHALL
   forward it to Operator2 by calling the “ES2.HandleProfileDisabledNotification” or the
   “ES2.HandleProfileDeletedNotification”.
(15)   The SM-SR SHALL send the "ES4.HandleProfileEnabledNotification" to a M2M SP,
   if authorised by Operator1 the owner of the Profile that was Disabled at the beginning of
   the procedure.
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   Operator1, the SM-SR SHALL send this notification to this other Operator by calling the
   “ES4.HandleProfileEnabledNotification”.
   If the M2M SP is another Operator connected through its SM-DP and it is authorised by
   Operator1, the SM-SR SHALL send this notification to the SM-DP associated to this other
   Operator by calling the “ES3.HandleProfileEnabledNotification”.
   Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting
   as the M2M SP, by calling the “ES2.HandleProfileEnabledNotification”.
(16)  The SM-SR SHALL send the "ES4.HandleProfileDisabledNotification" or
   "ES4.HandleProfileDeletedNotification" (if deletion was triggered by the evaluation of
   POL1 and POL2) to a M2M SP, if authorised by Operator2 the owner of the Profile that
   was Enabled at the beginning of the procedure.
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   Operator2, the SM-SR SHALL send this notification to this other Operator by calling the
   “ES4.HandleProfileDisabledNotification” or “ES4.HandleProfileDeletedNotification”
   If the M2M SP is another Operator connected through its SM-DP and it is authorised by
   Operator2, the SM-SR SHALL send this notification to the SM-DP associated to this other
Operator      by   calling     the     “ES3.HandleProfileDisabledNotification”         or
“ES3.HandleProfileDeletedNotification”.
  Then the SM-DP, on reception of this notification, SHALL forward it to the Operator,
  acting as the M2M SP, by calling the “ES2.HandleProfileDisabledNotification” or
  “ES2.HandleProfileDeletedNotification”

NOTE:This M2M SP might be the same M2M SP as for Operator1 or any other M2M SP.

NOTE:The MT-SMS and MO-SMS SHALL be secured according to section 2.4.

3.2.2 Connectivity Failure Case

The sequence flow in the Figure 16 describes the case where the target Profile cannot provide connectivity after it is enabled, and when roll-back to the previously Enabled Profile occurs.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “Operator1” as OP1 #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox

OP1->>SR: (1) EnableProfile(eid, iccid)
Rnote over SR #FFFFF
(2) Check initial conditions
Endrnote
SR-->>OP1: Failed
SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80
Rnote over ISDR #FFFFFF
(4) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80
SR-->>OP1: Failed
Rnote over ISDR #FFFFFF
(5) Enable ISD-P
Endrnote
ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80
SR-->>OP1: (6a) Failed
ISDR-->>DEV: (7) REFRESH, (UICC reset)
Rnote over DEV, ISDR #FFFFFF
(8) Network attachment with the enabled profile **fails**
                                OR
                   Notification procedure **fails**
Endrnote
|||
Hnote over ISDR #FFFFFF
(9) Enable previous ISD-P
Endhnote
ISDR-->>DEV: (10) REFRESH, (UICC reset)
Rnote over DEV, ISDR #FFFFFF
(11) Network attachment with the enabled profile
Endrnote
|||
Hnote right of SR #FFFFFF
(12)                 Notification procedure over SMS
Endhnote
|||
SR-->>OP1: (13) Profile enabling failure
@enduml

Figure 16: Profile Enabling failure, with roll-back

Start Conditions: The start conditions are identical to section 3.2.1.

Procedure: Steps (1), (2), (3), (4), (5), (6), (6a) and (7) are also identical to section 3.2.1.

(8) A network attach failure occurs indicating that the Enabled Profile cannot provide
    connectivity, or the eUICC doesn’t succeed to send the SMS notification (after having
    exhausted all possible retries), or doesn’t receive the SM-SR notification confirmation.
(9) The ISD-R SHALL enable the Profile that was previously enabled before the reception of
    the command, to re-establish connectivity.

NOTE:Profile change includes a change of the IMSI that is used to attach to the network. As indicated in 3GPP TS 31.102 [52], such a change requires special caution and should always be accompanied by a REFRESH command to avoid inconsistent information being read by the terminal. So while the targeted ISD-P is marked as enabled in this step, it MAY actually become effective only after the terminal executes the REFRESH command.

(10)     The ISD-R sends a REFRESH proactive command in UICC reset mode to the Device.
      This will trigger the execution of a new network attach procedure.
(11)     The eUICC and the Device SHALL perform a new network attach procedure with the
      Profile Enabled before the start of the procedure.
(12)     The eUICC SHALL perform the notification procedure as described in section 4.1.1.11.
      On reception of the SMS notification, the SM-SR is informed that the target Profile has not
      been enabled.
(13)    Finally, the SM-SR SHALL return the response to the “ES4.EnableProfile” function to
      Operator1; indicating a failure, the target Profile didn’t succeed to provide the connectivity.

3.3 Profile Enabling Via SM-DP

The Profile Enabling procedure between the Operator and the SM-DP is used to enable a Profile previously downloaded and installed on an eUICC (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.5). The procedure is initiated by the Operator owning the Profile to be enabled. The procedure illustrates the usage of SMS as a possible transport protocol between SM-SR and eUICC, but can be also performed using other transport protocols.

This procedure is similar to the procedure “Enable Profile” described in section 3.2.

3.3.1 Normal Case

The sequence flow in the 0 describes the normal case where the targeted Profile can successfully be enabled.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox

OP1->>DP: (0) Cond.: EnableProfile(eid, smsr-id, iccid)
DP->>SR: (1) EnableProfile(eid, iccid)
Rnote over SR #FFFFF
(2) Check initial conditions
Endrnote
SR-->>DP: Failed
DP-->>OP1: Failed
SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80
Rnote over ISDR #FFFFFF
(4) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80
SR-->>DP: Failed
DP-->>OP1: Failed
Rnote over ISDR #FFFFFF
(5) Enable ISD-P
Endrnote
ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80
SR-->>DP: (6a) Failed
DP-->>OP1: Failed
ISDR-->>DEV: (7) REFRESH, (UICC reset)
Rnote over DEV, ISDR #FFFFFF
(8) Network attachment with the enabled profile
Endrnote
|||
Hnote right of SR #FFFFFF
(9)                  Notification procedure over SMS
Endhnote
|||
Rnote over SR #FFFFFF
(10) Check POL2
Endrnote
SR->>ISDR: (11) Cond.: MT-SMS [ES5.DELETE command]SCP80
Rnote over ISDR #FFFFFF
(11a) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.DELETE command FAILED response]SCP80
SR-->>DP: Failed
DP-->>OP1: Failed
Rnote over ISDR #FFFFFF
(11b) Delete disabled ISD-P
and contained profile
Endrnote
ISDR-->>SR: (11c) MO-SMS [ES5.DELETE command response]SCP80
Rnote over SR #FFFFFF
(12) Update EIS
Endrnote
SR-->>DP: (13) Profile enabling result

SR->>OP2: (14) HandleProfileDisabledNotification(eid, iccid2) SR->>M2MSP: (15) HandleProfileEnabledNotification (eid, iccid) SR->>M2MSP: (16) HandleProfileDisabledNotification (eid, iccid2) DP-->>OP1: (17) Cond.: Profile enabling result

@enduml

Figure 17: Profile Enabling, Success Case

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure: (0) Operator1, the owner of the target Profile, SHALL call the “ES2.EnableProfile” function with its relevant input data, see section 5.3.5, in particular the identification of the SM-SR in charge of the management of the target eUICC. If the Profile Enabling procedure has been requested during a Profile Download (see section 3.1.3), this step is not applicable. (1) The SM-DP SHALL forward the request to the SM-SR provided by the Operator and SHALL call the function “ES3.EnabledProfile”. During this step the SM-DP may have to establish a link to the SM-SR (see section 2.6).

Steps (2) to (12) are the same as in the procedure “Profile Enabling” described in section 3.2.1.

(13) The SM-SR SHALL return the response to the “ES3.EnableProfile” function to the
   SM-DP, indicating that the Profile has been enabled.
(14)   Unless Operator2 has set an ONC to not receive those notifications, the SM-SR
   SHALL         send         the      “ES4.HandleProfileDisabledNotification”           or
   “ES4.HandleProfileDeletedNotification” (if deletion was triggered by the evaluation of
   POL1 and POL2) to Operator2, the owner of the Profile that was enabled at the beginning
   of the procedure. In case Operator2 has no direct connection with the SM-SR, the SM-SR
   SHALL apply the same process as described in point (14) of section 3.2.1.
(15)   The SM-SR SHALL send the "ES4.HandleProfileEnabledNotification" to a M2M SP,
   if authorised by Operator1 the owner of the Profile that was disabled at the beginning of
   the procedure.
(16)  The SM-SR SHALL send the "ES4.HandleProfileDisabledNotification" or
   "ES4.HandleProfileDeletedNotification" (if deletion was triggered by the evaluation of
   POL1 and POL2) to a M2M SP, if authorised by Operator2 the owner of the Profile that
   was enabled at the beginning of the procedure.
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   Operator1, the SM-SR SHALL send this notification to this other Operator by calling the
   “ES4.HandleProfileEnabledNotification”.
   If the M2M SP is another Operator connected through its SM-DP and it is authorised by
   Operator1, the SM-SR SHALL send this notification to the SM-DP associated to this other
   Operator by calling the “ES3.HandleProfileEnabledNotification”.
   Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting
   as the M2M SP, by calling the “ES2.HandleProfileEnabledNotification”.

NOTE:This M2M SP might be the same M2M SP as for Operator1 or any other M2M SP.

(17)   Finally, the SM-DP SHALL return the response to the “ES2.EnableProfile” function
   call to Operator1. If the Profile Enabling procedure has been requested during a Profile
   Download (see section 3.1.3), then the SM-DP SHALL NOT execute this step.

3.3.2 Connectivity Failure Case

The sequence flow in the Figure 18 describes the case where the targeted Profile cannot provide connectivity after it is enabled, and when roll-back to the previously Enabled Profile occurs.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “Operator1” as OP1 #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox

OP1->>DP: (0) Cond.: EnableProfile(eid, smsr-id, iccid)
DP->>SR: (1) EnableProfile(eid, iccid)
Rnote over SR #FFFFF
(2) Check initial conditions
Endrnote
SR-->>DP: Failed
DP-->>OP1: Failed
SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80
Rnote over ISDR #FFFFFF
(4) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80
SR-->>DP: Failed
DP-->>OP1: Failed
Rnote over ISDR #FFFFFF
(5) Enable ISD-P
Endrnote
ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80
SR-->>DP: (6a) Failed
DP-->>OP1: Failed
ISDR-->>DEV: (7) REFRESH, (UICC reset)
Rnote over DEV, ISDR #FFFFFF
(8) Network attachment with the enabled profile **fails**
                                 OR
                   Notification procedure **fails**
Endrnote
|||
Hnote over ISDR #FFFFFF
(9) Enable previous ISD-P
Endhnote
ISDR-->>DEV: (10) REFRESH, (UICC reset)
Rnote over DEV, ISDR #FFFFFF
(11) Network attachment with the enabled profile
Endrnote
|||
Hnote right of SR #FFFFFF
(12)                  Notification procedure over SMS
Endhnote
|||
SR-->>DP: (13) Profile enabling failure
DP-->>OP1: (14) Cond.: Profile enabling failure
@enduml

Figure 18: Profile Enabling, With Roll-Back

Start Conditions: The start conditions are the same as in section 3.3.1.

Procedure: Steps (0) and (1) are the same as in section 3.3.1. If the Profile Enabling procedure has been requested during a Profile Download (see section 3.1.3), the step (0) is not applicable.

Steps (2) to (12) are the same as in procedure “Connectivity failure case” as described in section 3.2.2.

(13) The SM-SR SHALL return the response to the “ES3.EnableProfile” function to the SM-DP, indicating a failure, the target Profile didn’t succeed to provide the connectivity.

(14)    Finally, the SM-DP SHALL return the response to the “ES2.EnableProfile” function to
   Operator1, indicating a failure, the target Profile didn’t succeed to provide the connectivity.
   If the Profile Enabling procedure has been requested during a Profile Download (see
   section 3.1.3), then the SM-DP SHALL NOT execute this step.

NOTE:In case the previously Enabled Profile can also not provide connectivity, the eUICC SHALL activate the Fall-Back Mechanism.

3.4 Profile Disabling

The Profile Disabling procedure is initiated by the Operator owning the Profile to be disabled. The procedure illustrated using SMS as a possible transport protocol between the SM-SR and the eUICC, but can be also performed using other transport protocols.

The sequence flow in the 0 describes the case where the targeted Profile can successfully be disabled.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox

OP1->>SR: (1) DisableProfile(eid, iccid)
Rnote over SR #FFFFF
(2) Check initial conditions
Endrnote
SR-->>OP1: Failed
SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80
Rnote over ISDR #FFFFFF
(4) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80
SR-->>OP1: Failed
Rnote over ISDR #FFFFFF
(5) Disable ISD-P
Endrnote
ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80
SR-->>OP1: (6a) Failed
ISDR-->>DEV: (7) REFRESH, (UICC reset)
Rnote over DEV, ISDR #FFFFFF
(8) Network attachment using profile with Fall-Back Attribute
Endrnote
|||
Hnote right of SR #FFFFFF
(9)                  Notification procedure over SMS
Endhnote
|||
Rnote over SR #FFFFFF
(10) Check POL2
Endrnote
SR->>ISDR: (11) Cond.: MT-SMS [ES5.DELETE command]SCP80
Rnote over ISDR #FFFFFF
(11a) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.DELETE command FAILED response]SCP80
SR-->>OP1: Failed
Rnote over ISDR #FFFFFF
(11b) Delete disabled ISD-P
and contained profile
Endrnote
ISDR-->>SR: (11c) MO-SMS [ES5.DELETE command response]SCP80
Rnote over SR #FFFFFF
(12) Update EIS
Endrnote
SR-->>OP1: (13) Profile disabling result
SR->>OP2: (14) HandleProfileEnabledNotification(eid, iccid2)
SR->>M2MSP: (15) HandleProfileDisabledNotification (eid, iccid)
SR->>M2MSP: (16) HandleProfileEnabledNotification (eid, iccid2)

@enduml

Figure 19: Profile Disabling

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure: (1) Operator1, the owner of the target Profile SHALL call the “ES4.DisableProfile” function with its relevant input data. (2) The SM-SR SHALL verify that the Operator1 request is acceptable (the verifications that the SM-SR SHALL perform are described in the section 5.5.6, and in particular checks that Profile is enabled and Profile disabling is allowed in POL2. If any of the conditions to be verified are not satisfied, the SM-SR SHALL return a response indicating the failure, and the procedure SHALL end. (3) The SM-SR SHALL send an MT-SMS containing the “ES5.STORE DATA” command for Profile disabling with its relevant input data (see section 4.1.1.3) to the ISD-R. The SM-SR SHALL request a PoR to get the execution status of the “ ES5.STORE DATA” command. (4) The ISD-R SHALL enforce POL1 of the currently Enabled Profile. In case POL1 rejects disabling, the ISD-R SHALL return PoR containing the response indicating a failure, and the procedure SHALL end.

(5) The ISD-R SHALL disable the targeted ISD-P and the contained Profile and SHALL enable
   the Profile with the Fall-Back Attribute set.
   NOTE:        Profile change includes a change of the IMSI that is used to attach to the
                network. As indicated in 3GPP TS 31.102 [52], such a change requires
                special caution and should always be accompanied by a REFRESH
                command to avoid inconsistent information being read by the terminal. So
                while the targeted ISD-P is marked as enabled in this step, it MAY actually
                become effective only after the terminal executes the REFRESH command.
(6) The ISD-R SHALL return the MO-SMS containing the execution status of the “ES5.STORE
   DATA” command to the SM-SR.
       (6a)   If the response to the “ES5.STORE DATA” command indicates a failure, the SM-
              SR SHALL return a response indicating the failure to Operator1, and the
              procedure SHALL end.
(7) The ISD-R sends a REFRESH proactive command in UICC reset mode to the Device.
   This will trigger the execution of a network attach procedure.
   NOTE:        In case of any error after this step indicating that the current Enabled Profile
                cannot provide connectivity, the ISD-R SHALL re-enable the previously
                Enabled Profile as described in section 3.2.2.
(8) The eUICC and the Device SHALL perform a new network attach procedure with the
   Profile with the Fall-Back Attribute set.
(9) The eUICC SHALL perform the notification procedure as described in section 4.1.1.11.
   During this procedure, if ISD-R doesn’t succeed to send the SMS notification, or doesn’t
   receive the SM-SR notification confirmation, this SHALL be considered as an error, and
   the previous note SHALL apply.
   On reception of the SM-SR notification confirmation command, if POL1 of the Disabled
   Profile contains the rule “Profile deletion is mandatory when it is disabled”, the ISD-R
   SHALL delete the disabled ISD-P and the contained Profile. The eUICC SHALL send the
   response to the notification confirmation indicating whether the disabled ISD-P has been
   deleted or not.
(10)   On reception of the ES5.HandleNotificationConfirmation response, and if the
   ES5.HandleNotificationConfirmation response indicates that the Disabled Profile has
   not been deleted, the SM-SR SHALL evaluate POL2 of the Disabled Profile. If POL2 of
   the Disabled Profile contains the rule “Profile deletion is mandatory when it is disabled”,
   the SM-SR SHALL perform step (11), else it SHALL jump to step (12).
(11)    The SM-SR SHALL send an MT-SMS containing the “ES5.DELETE” command with
   its relevant input data (see section 4.1.1.4) to the ISD-R, targeting the Disabled Profile.
   The SM-SR SHALL request a PoR to get the execution status of the “ES5.DELETE”
   command.
(11a) The ISD-R SHALL enforce POL1 of the target Profile. If POL1 rejects the deletion of
      the target Profile, the ISD-R SHALL return the MO-SMS containing the response
      indicating the corresponding failure, and the procedure SHALL end.
(11b) If POL1 allows its deletion, the ISD-R SHALL delete the targeted ISD-P and the
      contained Profile.
(11c) The ISD-R SHALL return the MO-SMS to the SM-SR containing the execution status
      of the “ES5.DELETE” command.
(12)  According to the executed sequence and the eUICC responses, the SM-SR SHALL
   update the EIS to reflect that:
    The Profile having the Fall-Back Attribute has been enabled
      The previously Enabled Profile has been disabled or deleted.
   NOTE:         POL1 and POL2 MAY have different content. As a consequence, both the
                 eUICC and the SM-SR have to ensure the ISD-P deletion based on their
                 respective Policy.
(13)  The SM-SR SHALL return the response to the “ES4.DisableProfile” function to
   Operator1, indicating that the Profile has been disabled. In case the Profile has also been
   deleted because of POL1 or POL2, the function execution response SHALL include an
   execution status “Executed-WithWarning” indicating that the Profile has also been deleted.
(14)    Unless Operator2 has set an ONC to not receive those notifications, the SM-SR
   SHALL send the “ES4.HandleProfileEnabledNotification” to Operator2, the owner of
   Profile with Fall-Back Attribute set that is now enabled. In case Operator2 has no direct
   connection with the SM-SR (SM-SR SHALL be able to detect such situation based on its
   own database), the SM-SR SHALL send this notification to the SM-DP authorised by
   Operator2 by calling the “ES3.HandleProfileEnabledNotification”. The SM-SR can
   retrieve the SM-DP identity based on the EIS content. Then the SM-DP, on reception of
   this    notification, SHALL        forward     it  to    Operator2 by       calling   the
   “ES2.HandleProfileEnabledNotification”.
(15) The SM-SR SHALL send the "ES4.HandleProfileDisabledNotification" to a M2M
   SP, if authorised by Operator1 the owner of the Profile that was enabled at the beginning
   of the procedure.
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   Operator1, the SM-SR SHALL send this notification to this other Operator by calling the
   “ES4.HandleProfileDisabledNotification”.
   If the M2M SP is another Operator connected through its SM-DP and it is authorised by
   Operator1, the SM-SR SHALL send this notification to the SM-DP associated to this other
   Operator      by       calling     the        “ES3.HandleProfileDisabledNotification”.
   Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting
   as the M2M SP, by calling the “ES2.HandleProfileDisabledNotification”
(16)   The SM-SR SHALL send the "ES4.HandleProfileEnabledNotification" to a M2M SP,
   if authorised by Operator2 the owner of Profile with Fall-Back Attribute set that is now
   enabled.
       If the M2M SP is another Operator directly connected to the SM-SR and it is authorised
       by Operator2, the SM-SR SHALL send this notification to this other Operator by calling
       the “ES4.HandleProfileEnabledNotification”.
         If the M2M SP is another Operator connected through its SM-DP and it is authorised
       by Operator2, the SM-SR SHALL send this notification to the SM-DP associated to this
       other Operator by calling the “ES3.HandleProfileEnabledNotification”.
       Then the SM-DP, on reception of this notification, SHALL forward it to the Operator,
       acting as the M2M SP, by calling the “ES2.HandleProfileEnabledNotification”.

NOTE:This M2M SP might be the same M2M SP as for Operator1 or any other M2M SP.

NOTE:The MT-SMS and MO-SMS SHALL be secured according to section 2.4.

3.5 Profile Disabling Via SM-DP

The Profile Disabling procedure is initiated by the Operator owning the Profile to be disabled through the SM-DP. The procedure illustrated using SMS as a possible transport protocol between SM-SR and eUICC, but can be also performed using other transport protocols.

This procedure is similar to the procedure “Disable Profile” described in section 3.4.

The sequence flow in the Figure 20 describes the case where the targeted Profile can successfully be disabled.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox

OP1->>DP: (0) DisableProfile(eid, smsr-id, iccid)
DP->>SR: (1) DisableProfile(eid, iccid)
Rnote over SR #FFFFF
(2) Check initial conditions
Endrnote
SR-->>DP: Failed
DP-->>OP1: Failed
SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80
Rnote over ISDR #FFFFFF
(4) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80
SR-->>DP: Failed
DP-->>OP1: Failed
Rnote over ISDR #FFFFFF
(5) Disable ISD-P
Endrnote
ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80
SR-->>DP: (6a) Failed
DP-->>OP1: Failed
ISDR-->>DEV: (7) REFRESH, (UICC reset)
Rnote over DEV, ISDR #FFFFFF
(8) Network attachment using profile with Fall-Back attribute
Endrnote
|||
Hnote right of SR #FFFFFF
(9)                  Notification procedure over SMS
Endhnote
|||
Rnote over SR #FFFFFF
(10) Check POL2
Endrnote
SR->>ISDR: (11) Cond.: MT-SMS [ES5.DELETE command]SCP80
Rnote over ISDR #FFFFFF
(11a) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.DELETE command FAILED response]SCP80
SR-->>DP: Failed
DP-->>OP1: Failed
Rnote over ISDR #FFFFFF
(11b) Delete disabled ISD-P
and contained profile
Endrnote
ISDR-->>SR: (11c) MO-SMS [ES5.DELETE command response]SCP80
Rnote over SR #FFFFFF
(12) Update EIS
Endrnote
SR-->>DP: (13) Profile disabling result

SR->>OP2: (14) HandleProfileEnabledNotification(eid, icci d2) SR->>M2MSP: (15) HandleProfileDisabledNotification (eid, iccid) SR->>M2MSP: (16) HandleProfileEnabledNotification (eid, iccid2) DP-->>OP1: (17) Profile disabling result @enduml

Figure 20: Profile Disabling Via SM -DP

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure: (0) Operator1, the owner of the target Profile, SHALL call the “ES2.DisableProfile” function with its relevant input data, see section 5.3.6, in particular the identification of the SM-SR in charge of the management of the target eUICC. (1) The SM-DP SHALL forward the request to the SM-SR identified by the Operator and SHALL call the “ES3.DisableProfile” function with its relevant input data. Steps (2) to (12) are the same as in the procedure “Profile Disabling” described in section 3.4. (13) The SM-SR SHALL return the response to the “ES3.DisableProfile” function to the SM-DP, indicating that the Profile has been disabled. In case the Profile has also been deleted because of POL1 or POL2, the function execution response SHALL include an

      execution status “Executed-With Warning” indicating that the Profile has also been
      deleted.
(14)     Unless Operator2 has set an ONC to not receive those notifications, the SM-SR
      SHALL send the “ES4.HandleProfileEnabledNotification” to Operator2, the owner of the
      Profile with Fall-Back Attribute set that is now enabled.
(15)      The SM-SR SHALL send the "ES4.HandleProfileDisabledNotification" to a M2M
      SP, if authorised by Operator1 the owner of the Profile that was enabled at the beginning
      of the procedure.
      If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
      Operator1, the SM-SR SHALL send this notification to this other Operator by calling the
      “ES4.HandleProfileDisabledNotification”.
      If the M2M SP is another Operator connected through its SM-DP and it is authorised by
      Operator1, the SM-SR SHALL send this notification to the SM-DP associated to this other
      Operator by calling the “ES3.HandleProfileDisabledNotification”.
      Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting
      as the M2M SP, by calling the “ES2.HandleProfileDisabledNotification”
(16)      The SM-SR SHALL send the "ES4.HandleProfileEnabledNotification" to a M2M SP,
      if authorised by Operator2 the owner of Profile with Fall-Back Attribute set that is now
      enabled.
      If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
      Operator2, the SM-SR SHALL send this notification to this other Operator by calling the
      “ES4.HandleProfileEnabledNotification”.
      If the M2M SP is another Operator connected through its SM-DP and it is authorised by
      Operator2, the SM-SR SHALL send this notification to the SM-DP associated to this other
      Operator by calling the “ES3.HandleProfileEnabledNotification”.
      Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting
      as the M2M SP, by calling the “ES2.HandleProfileEnabledNotification”.

NOTE:This M2M SP might be the same M2M SP as for Operator1 or any other M2M SP.

(17)      Finally, the SM-DP SHALL return the response to the “ES2.DisableProfile” function
      call to Operator1.

NOTE:The MT-SMS and MO-SMS SHALL be secured according to section 2.4.

3.6 Profile and ISD-P Deletion

The Profile and ISD-P deletion procedure between the Operator and the SM-SR is used to delete the target ISD-P with its Profile on the eUICC (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.4). The procedure is initiated by the Operator owning the Profile to be deleted. The procedure illustrates the usage of SMS as a possible transport protocol between SM-SR and eUICC, but can be also performed using other transport protocols.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox

OP->>SR: (1) DeleteProfile(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>OP: Failed Rnote over SR, ISDR #ADD1B2 (3) Optional: If targeted profile is enabled, then execute function "ES4.DisableProfile" Endrnote SR-->>OP: Failed SR->>ISDR: (4) MT-SMS [ES5.DELETE command]SCP80 Rnote over ISDR #FFFFFF (5) Enforce POL1 Endrnote ||| Rnote over ISDR #FFFFFF (6) Delete ISD-P Endrnote ISDR-->>SR: (7) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (8) Update EIS Endrnote SR-->>OP: (9) Profile deletion result SR->>M2MSP: (10) Cond: HandleProfileDeletedNotification (eid, iccid) @enduml

Figure 21: Profile and ISD-P Deletion

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:
(1) The Operator owning the target Profile SHALL call the “ES4.DeleteProfile” function with
   its relevant input data.
(2) The SM-SR SHALL verify that the Operator request is acceptable (the verifications that
   the SM-SR SHALL perform are described in the section 5.4.7), and in particular SHALL
   evaluate POL2 of the target Profile. If any of the conditions to be verified are not satisfied,
   the SM-SR SHALL return a response indicating the failure, and the proce dure SHALL end.
(3) The SM-SR SHALL check the state of the target Profile. If the target Profile is enabled and
   if POL2 of the target Profile allows it to be disabled, then the SM-SR SHALL execute the
   “ES4.DisableProfile” function to first disable the target Profile (and thus enable the Profile
   having the Fall-Back Attribute). In case of error, a response indicating the failure is returned
   to the Operator, and the procedure SHALL end.
   NOTE:        Profile change includes a change of the IMSI that is used to attach to the
                network. As indicated in 3GPP TS 31.102 [52], such a change requires
                special caution and should always be accompanied by a REFRESH
                command to avoid inconsistent information being read by the terminal. So
                while the targeted ISD-P is marked as enabled in this step, it MAY actually
                become effective only after the terminal executes the REFRESH command.

(4) The SM-SR SHALL send an MT-SMS containing the “ES5.DELETE” command with its relevant input data (see section 4.1.1.4) to the ISD-R. The SM-SR SHALL request a PoR to get the execution status of the “ES5.DELETE” command.

(5) The ISD-R, SHALL enforce POL1. If POL1 rejects deletion of the target Profile, the ISD-R
      SHALL return directly the MO-SMS containing the response indicating a failure, and the
      procedure SHALL end.
(6) If POL1 allows, the ISD-R SHALL delete the targeted ISD-P and the contained Profile.
(7) The ISD-R SHALL return the MO-SMS containing the execution status of the
      “ES5.DELETE” command to the SM-SR.
(8) In case of successful execution, the SM-SR SHALL update the EIS to reflect the newly
      deleted Profile.
(9) Finally, the SM-SR SHALL return the response to the “ES4.DeleteProfile” function to the
      caller Operator.
(10)      The SM-SR SHALL send the "ES4.HandleProfileDeletedNotification" to a M2M SP,
      if authorised by the Operator who owns the Profile, indicating that the profil e has been
      deleted.
      If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
      the Operator owning the Profile, the SM-SR SHALL send this notification to this other
      Operator by calling the “ES4.HandleProfileDeletedNotification”.
      If the M2M SP is another Operator connected through its SM-DP and it is authorised by
      the Operator owning the Profile, the SM-SR SHALL send this notification to the SM-DP
      associated to this other Operator by calling the “ES3.HandleProfileDeletedNotification”.
      Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting
      as the M2M SP, by calling the “ES2.HandleProfileDeletedNotification”

NOTE:The MT-SMS and MO-SMS SHALL be secured according to section 2.4.

3.7 Profile and ISD-P Deletion Via SM-DP

The Profile and ISD-P deletion procedure is used between the Operator and the SM-DP to delete the target ISD-P with its Profile on the eUICC (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.4). The procedure is initiated by the Operator owning the target Profile and is actually performed by the SM-SR in charge of the eUICC management. The procedure illustrates the usage of SMS as a possible transport protocol between SM-SR and eUICC, but can be also performed using other transport protocols.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox OP->>DP: (1) DeleteProfile(eid, iccid, smsr -id) DP->>SR: (2) DeleteProfile(eid, iccid) Rnote over SR #FFFFF (3) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP: Failed Rnote over SR, ISDR #ADD1B2 (4) Optional: If targeted profile is enabled, then execute function "ES4.DisableProfile" Endrnote SR-->>DP: Failed DP-->>OP: Failed SR->>ISDR: (5) MT-SMS [ES5.DELETE command]SCP80 Rnote over ISDR #FFFFFF (6) Enforce POL1 Endrnote ||| Rnote over ISDR #FFFFFF (7) Delete ISD-P Endrnote ISDR-->>SR: (8) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (9) Update EIS Endrnote SR-->>DP: (10) Profile deletion result SR->>M2MSP: (11) Cond: HandleProfileDeletedNotification (eid, iccid) DP-->>OP: (12) Profile deletion result @enduml

Figure 22: Profile and ISD-P Deletion via SM-DP

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:
(1) The Operator owning the Profile which is to be deleted SHALL call the “ES2.DeleteProfile”
   function with its relevant input data (we assume that the Operator knows the identification
   and the address of the SM-SR, as the Operator has a Profile on the eUICC managed by
   this SM-SR). The identification and address of the SM-SR in charge of the management
   of the eUICC SHALL be provided at that time to the SM-DP.
(2) The SM-DP SHALL forward the Operator request to the relevant SM-SR.
(3) The SM-SR SHALL verify if the SM-DP request is acceptable (the verifications that the
   SM-SR SHALL perform are described in section 5.4.9), and, in particular, SHALL evaluate
   POL2 of the target Profile. If any of the conditions to be verified are not satisfied, the SM-
   SR SHALL return a response indicating a failure, and the procedure SHALL end.
(4) The SM-SR SHALL check the state of the target Profile. If the target Profile is enabled and
   if POL2 of the target Profile allows it to be disabled, then the SM-SR SHALL execute the
   “ES4.DisableProfile” function to first disable the target Profile (and thus enable the Profile
   having the Fall-Back Attribute). In case of error, a response indicating the failure SHALL
   be returned to the SM-DP, who forwards it to the Operator, and the procedure SHALL end.
   NOTE:        Profile change includes a change of the IMSI that is used to attach to the
                network. As indicated in 3GPP TS 31.102 [52], such a change requires special
                caution and should always be accompanied by a REFRESH command to
                avoid inconsistent information being read by the terminal. So while the
                targeted ISD-P is marked as enabled in this step, it MAY actually become
                effective only after the terminal executes the REFRESH command.
(5) The SM-SR SHALL send an MT-SMS containing the “ES5.DELETE” command with its
      relevant input data (see section 4.1.1.4) to the ISD-R. The SM-SR SHALL request a PoR
      to get the execution status of the “ES5.DELETE” command.
(6) The ISD-R SHALL enforce POL1. If POL1 rejects the deletion of the target Profile, the
      ISD-R SHALL return the MO-SMS containing the response indicating a failure, and the
      procedure SHALL end.
(7) If POL1 allows its deletion, the ISD-R SHALL delete the targeted ISD-P and the contained
      Profile.
(8) The ISD-R SHALL return the MO-SMS to the SM-SR containing the execution status of
      the “ES5.DELETE” command.
(9) In case of successful execution, the SM-SR SHALL update the EIS to reflect the newly
      deleted Profile.
(10)     The SM-SR SHALL return the response to the “ES3.DeleteISDP” function to the SM-
      DP.
(11)      The SM-SR SHALL send the "ES4.HandleProfileDeletedNotification" to a M2M SP,
      if authorised by the Operator owning the Profile, indicating that the profile has been
      deleted.
      If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
      the Operator owning the Profile, the SM-SR SHALL send this notification to this other
      Operator by calling the “ES4.HandleProfileDeletedNotification”.
      If the M2M SP is another Operator connected through its SM-DP and it is authorised by
      the Operator owning the Profile, the SM-SR SHALL send this notification to the SM-DP
      associated to this other Operator by calling the “ES3.HandleProfileDeletedNotification”.
      Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting
      as the M2M SP, by calling the “ES2.HandleProfileDeletedNotification”
(12)      Finally, the SM-DP SHALL forward the received response to the Operator.

NOTE:The MT-SMS and MO-SMS SHALL be secured according to section 2.4.

3.8 SM-SR Change

The SM-SR Change procedure is used between the Initiator Operator (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 2.3.1) and the SM-SRs to change the SM-SR for the target eUICC (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.11) from SM-SR1 to SM-SR2.

This sequence uses the same key establishment mechanism as section 3.1.2.

 MNO/                                                    SM-SR1                                SM-SR2                                                                eUICC
SM-DPs                                                                                                                                                                             ISD-R                             ECASD
                                Initiator
                                  MNO
                                  (1)PrepareSMSRChange(eid,currentsmsrid)
                                   Failed
                                                (2)Check initial conditions
(3)PrepareSMSRChange success
(4)SMSRChange (eid, targetsmsrid)
                                             (5)HandoverEIUCC(eis)
                      Failed
                                               Failed
                                                            (6)Verify ECASD Certificate
(7)AuthenticateSMSR (eid, CERT.SR.ECDSA)
                                               (8)EstablishISDRKeySet (CERT.SR.ECDSA)

(8a) verify that it is an SM-SR certificate

(9) (CERT.SR.ECDSA)

                                                                                                                                                                                                                       (10)
                                                                                                                                                                                            - verify CERT.SR.ECDSA using PK.CI.ECDSA
If any operation                                                                                                                                                                            - extract and store PK.SR.ECDSA from CERT.SR.ECDSA
fails/expires,                                                                                                                                                                              - generate Random Challenge RC
SMSR1 return                                                                                      (12) EstablishISDRKeySet success (RC)
status=‘Failed’ for                                                                                                                                                                            (11) RC
ES4.SMSRChange                                                  (13) AuthenticateSMSR success
response
                                                                                             (14)
                                                                   - Generate ephemeral key pair (eSK,SR.ECKA, ePK.SR.ECKA)
                                                                   - Signs RC and ePK.SR.ECKA with SK.SR.ECDSA

(15) CreateAdditionalKeySet (eid, ePK.SR.ECKA, signature)

(16) EstablishISDRKeySet (ePK.SR.ECKA, signature)
                                                                                                                   (17) (ePK.SR.ECKA, signature)
                            (18)
- verify signature using PK.SR.ECDSA
- calculate ShS from ePK.SR.ECKA and SK.ECASD.ECKA

(19) (ShS)

                                                                                          (20)
                                                                  - Optional: generate DR
                                                                  - derive key set KS2 from ShS (and, if generated, DR)
                                                                  - calculate receipt
(21) EstablisISDRKeySet (receipt and opt: DR)

(22) CreateAdditionalKeySet response (receipt)

Failed     (23) Verify receipt and calculate KS2
                                                      (24) secureChannelSetup (KS2)
If any operation                                                                                                           (25) FinaliseISDRhandover
fails/expires, SM-SR2 and
SM-SR1 return Status=                                                                                                      (26) Optional ISD-R configuration
‘Success_WithWarning’
for respectively
ES7.HandoverEuicc and                                                                                                     (27) FinaliseISDRhandover result
ES4.SMSRChange                                                                         (28) EIS update                    (and optional ISD-R reconfiguration result)
responsess
                                                                   (29)HandovereUICC success
                                                  (30) Delete EIS
                               (31) SMSRChange Success
(32) SMSRChangeNotification

Figure 23: SM-SR Change

NOTE1:The same ISD-R is used by both SM-SRs.

NOTE2:The actions to perform in relationship to the Operator before the SM-SR change are out of scope of this specification.

NOTE3:The settings of the secure connections between the Operators and the SM- SRs are out of scope of this specification.

NOTE4:The interaction between CI and SM-SR2 is out of the scope of this procedure.

NOTE5:Profile Lifecycle Management Authorisations (PLMA, see chapter 3.20 for further details), on SM-SR1 SHALL NOT be taken into account during the change procedure to SM-SR2. If necessary, the operator SHALL perform

the procedures defined in 3.20.1 or 3.20.2 to configure PLMAs on the SM-
SR2.

NOTE6:In this procedure, the Initiator should be the Operator1 as it is the one requesting the transfer from SM-SR1 to SM-SR2.

Start Conditions:
         a) The EID of the eUICC is known to the Initiator Operator.
         a) The two OIDs of the SM-SR1 and SM-SR2 are known to the Initiator Operator.
         b) The ISD-R is personalised with the keys of SM-SR1.
         c) The change of SM-SR is allowed.
         d) SM-SR2 has a certificate signed by the Certificate Issuer (CI).
         e) The public key of the CI is stored in the ECASD.
Procedure:
(1) The Initiator Operator SHALL call the “ES4.PrepareSMSRChange” function addressing
   the new SM-SR with the EID as input data.
(2) SM-SR2 SHALL verify that it is prepared to manage this eUICC. A failure at this step will
   stop the procedure and the error information SHALL be returned to the Initiator Operator.
(3) SM-SR2 SHALL return a response indicating a success.
(4) The Initiator Operator SHALL call the SM-SR1 “ES4.SMSRChange” function with its
   relevant input. SM-SR1 SHALL verify that there is no pending action for the eUICC. SM-
   SR1 SHALL also reject any new management requests for the target eUICC as long as
   the procedure is on-going. In case of pending action(s), SM-SR1 SHALL stop the SM-SR
   Change procedure and indicate that other actions are pending..
(5) SM-SR1 SHALL call the SM-SR2 “ES7.HandoverEUICC” function with its relevant input
   data.
(6) SM-SR2 SHALL verify that:
        It has the capabilities to manage this eUICC.
        The ECASD certificate is valid, using the EUM Certificate and the CI’s Root
         Certificate. The ECASD certificate is part of the EIS and is provided in the
         HandoverEUICC function. SM-SR2 SHALL extract PK.ECASD.ECKA from the
         ECASD certificate.
(7) SM-SR2 SHALL call the “ES7.AuthenticateSMSR” function specifying the targeted
    eUICC and providing the certificate identifying SM-SR2, CERT.SR.ECDSA.
              a. In case SM-SR1 does not receive call 7 before the expiration of the Validity
                 Period specified by the Initiator Operator at step 4, SM-SR1 SHALL send an
                 error (‘Execution Status’ indicating ‘Failed’) to the Operator.
(8) SM-SR1 SHALL call the “ES5.EstablishISDRKeySet” function with CERT.SR.ECDSA as
   input data to authenticate SM-SR2.
       (8a)    The ISD-R SHALL verify that it is an SM-SR certificate.
(9) The ISD-R SHALL forward the CERT.SR.ECDSA to ECASD.
(10)       The ECASD SHALL:
            Verify CERT.SR.ECDSA using PK.CI.ECDSA;
            Extract and store PK.SR.ECDSA from CERT.SR.ECDSA;
          Generate a Random Challenge(RC). The length of the Random Challenge SHALL be
           16 or 32.
(11)       The ECASD SHALL return the Random Challenge (RC) to the ISD-R.
(12)  The ISD-R SHALL return a response indicating a success with the generated Random
   Challenge RC.
(13)       SM-SR1 r SHALL forward the Random Challenge to SM-SR2.
              b. In case of failure or expiration in steps 8 to 13, the SM-SR2 SHALL abort the
                 procedure and return an error in ES7.HandoverEuicc response. The SM-SR1
                 SHALL abort the procedure too and propagate the error to the Initiator
                 Operator.
(14)   SM-SR2 SHALL generate an ephemeral key pair (eSK.SR.ECKA, ePK.SR.ECKA) and
   sign the received Random Challenge (RC) and ePK.SR.ECKA with SK.SR.ECDSA.
(15)   SM-SR2 SHALL call the “ES7.CreateAdditionalKeyset” function specifying the
   targeted eUICC and providing the ePK.SR.ECKA and the previously generated signature.
              c. In case the Validity Period specified by SM-SR2 does not fit within the time
                 remaining out of the Validity Period specified by the Initiator Operator in step 4,
                 the SM-SR1 SHALL return an error to SM-SR2 indicating that the Validity
                 Period is refused.SM-SR2 MAY then retry call 15 with an acceptable Validity
                 Period
              d. In case SM-SR1 does not receive an acceptable call 15 before the expiration
                 of the Validity Period specified by the Initiator Operator at step 4, SM-SR1
                 SHALL send an error (‘Execution Status’ indicating ‘Failed’) to the Operator.
(16)  SM-SR1 SHALL call the “ES5.EstablishISDRKeySet” function with ePK.SR.ECKA
   and the signature as input data to request generation of an additional key set KS2.
(17)       The ISD-R SHALL forward ePK.SR.ECKA and the signature to ECASD
(18) The ECASD SHALL:
     Verify the signature using PK.SR.ECDSA. If unsuccessful an error SHALL be
       returned; else
     Calculate ShS from ePK.SR.ECKA and SK.ECASD.ECKA.
(19) The ECASD SHALL return the ShS to the ISD-R
(20)  The ISD-R SHALL:
        Optional: generates DR;
        Derive key set from ShS (and, if generated, DR);
        Calculate receipt.
(21) The ISD-R SHALL return a response indicating a success with the calculated receipt
   and optionally the DR.
(22)       SM-SR1 receives and SHALL forward the response to SM-SR2.

NOTE:By checking the consistency of the Validity Period at step 15b, SM-SR1 ensures that its own Validity Period does not expire before step 22.

(23)    SM-SR2 SHALL:
        Calculate the ShS from eSK.SR.ECKA and PK.ECASD.ECKA,
        Derive key set KS2 from ShS (and optional DR), and
        Verify the receipt.
        If the verification of the receipt fails, SM-SR2 SHALL send an error to SM-SR1
         and SM-SR1 SHALL forward the error to the Initiator Operator.
      If for any reason the procedure fails or expires on SM-SR2 before starting step 24,
         SM-SR2 SHALL delete the EIS from its database and send an error to SM-SR1,
         and SM-SR1 SHALL forward the error to the Initiator Operator.
(24) SM-SR2 SHALL open a secure channel (section 2.2.5.1) using the newly created key
   set KS2.
(25)       SM-SR2 SHALL call the “ES5.FinaliseISDRhandover” to delete the keys of SM-SR1.
(26)  Optionally, SM-SR2 MAY send other commands to update the ISD-R configuration
   (see NOTE below)
       Personalise other key sets to have the capability to use other secure channels
         using the PUT KEY command as specified in GlobalPlatform Card Specification
         v.2.2.1 [6]
       Update the HTTPS parameters of the admin agent in the ISD-R, as specified in
         GlobalPlatform Card Specification Amendment B [8]
       Update the DNS parameters if this feature is supported by the eUICC and SM-
         SR2
       Erase the DNS parameters if this feature is not supported by SM-SR2.
       Update the SM-SR addressing parameters of the ISD-R using the function ES5.
       UpdateSMSRAddressingParameters defined in section 4.1.1.10 This update is
         necessary before the eUICC sends a profile change notification, so SM-SR2
         SHALL perform this update before sending any enable or disable profile
         command, and it SHOULD perform this update as soon as possible (to cover the
         activation of the Fall-Back Mechanism).

NOTE:SM-SR2 SHOULD perform steps 25 and 26 in a single command script. SM- SR2 MAY provide the corresponding commands in any order.

(27)  The ISD-R SHALL return the result of the keys deletion (and the result of optional
   operations that have been sent at step 26) to SM-SR2.
(28)       SM-SR2 SHALL update the EIS to reflect that it now manages the eUICC.
(29)       SM-SR2 SHALL return to SM-SR1 that it has successfully registered the eUICC.
              e. If SM-SR2 has not received the result of the keys deletion at step 26, or if any
                 of the optional operations failed or expired, SM-SR2 SHALL still return to SM-
                 SR1 that it has registered the eUICC, but SHALL indicate a warning (status
                 "Executed-WithWarning").

(30) SM-SR1 SHALL remove the EIS for the target eUICC, even if SM-SR2 indicated a warning at step 29-a.

(31) SM-SR1 SHALL return the result of the SM-SR change function to the Initiator
   Operator.
         f. If SM-SR2 returned a warning at step 29, SM-SR1 SHALL also return a warning
             to the Operator
(32)   SM-SR2 SHALL call the “ES4.HandleSMSRChangeNotification” function, with its
   relevant input data, to notify the Operators owning the Profiles on the eUICC. In case an
   Operator has no direct connection with SM-SR2 (SM-SR2 SHALL be able to detect such
   situation based on its own database), SM-SR2 SHALL send this notification to the SM-DP
   authorised by such an Operator by calling the “ES3.HandleSMSRChangeNotification”
   function. SM-SR2 can retrieve the SM-DP identity based on the EIS content. Then the SM-
   DP, on reception of this notification, SHALL forward it to the Operator by calling the
   “ES2.HandleSMSRChangeNotification”.
The eUICC SHALL support key establishment with and without the DR. The SM-SR decides
which option to use.

BSI TR-03111 [49] contains recommendations and requirements on the generation and validation of ephemeral keys. In addition, NIST SP 800-56A [50] provides requirements on the destruction of ephemeral keys and other intermediate secret data after their use.

End Conditions:
          b) The ISD-R is personalised with only the key set of SM-SR2
          f) The eUICC is registered within SM-SR2
          g) The EIS and EID reside within SM-SR2
          h) SM-SR1 is no longer related to the eUICC and its EIS record has been erased
          i) The Operator(s) owning the Profile(s) are aware of the change
          j) The Initiator Operator is aware of the SM-SR change

Whatever the result and timing of these optional operations, successful completion of the ISD-R key establishment (steps 5 to 23 above), proven by successful verification of the receipt, ensures SM-SR2 is now able to manage the eUICC.

As soon as SM-SR2 has verified the receipt (step23 above), the management of the eUICC is ensured by the new SM-SR2. From this point, SM-SR2 SHALL only return a status “Executed-Success” or “Executed-WithWarning”, and SM-SR1 SHALL forward this status to the Initiator Operator and SHALL remove the EIS from its database, so that the Initiator Operator knows with no ambiguity which SM-SR is now managing the eUICC.

In case the deletion of SM-SR1 keys fails or does not complete (which only SM-SR2 knows), SM-SR2 is still responsible for the management of the eUICC.

In case the procedure expires on SM-SR1 side after step 22, even before the procedure completes or expires on SM-SR2, SM-SR1 SHALL inform the Initiator Operator. The Operator MAY then retry the procedure from step 1 or from step 4.

When retrying the procedure, if SM-SR2 had indeed completed step (23) on its side during the first attempt:

   SM-SR2 SHALL skip the steps (7) to (23)
   SM-SR2 SHALL perform steps (24) to (28) (if not already done during the first
    attempt)
   SM-SR2 SHALL return the response (29) with an indication that the eUICC is already
    managed

The SM-SR1 SHALL then delete the EIS, and return the response (31) indicating a Success_WithWarning to the Initiator.

3.9 eUICC Registration at SM-SR: Register a New EIS

This procedure is used by the EUM to register an EIS representing an eUICC at the SM-SR. The EIS is required by the SM-SR to perform Platform Management functions and enable Profile Management functions on the eUICC.

EUM                                        SM-SR

(1) registerEIS(eis)

Failed                  (2) Check EIS

(3) Store EIS

(4) RegisterEIS success

Figure 24: EIS Registration at SM-SR

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

It is assumed that the EUM has been given the SM-SR identity and address by the entity that has ordered the eUICC.

Procedure:
(1) The EUM that has manufactured the eUICC SHALL call the “ES1.RegisterEIS” function
      with the EIS data. The EIS SHALL include the data according to Annex E. The EIS SHALL
      be signed by the EUM.
(2) The SM-SR SHALL verify that the EUM request is acceptable (the verifications that the
      SM-SR SHALL perform are described in the section5.2.1). If any of the conditions to be
      verified is not satisfied, the SM-SR SHALL return a response indicating the failure, and the
      procedure SHALL end.
(3) The SM-SR SHALL store the new EIS in its database.
(4) The SM-SR SHALL return the successful response to the “ES1.RegisterEIS” function to
      the caller EUM.

3.10 Master Delete Procedure

This procedure deletes an Orphaned Profile regardless of the Profile’s Policy Rules. The procedure illustrates the usage of SMS as a possible transport protocol between SM-SR and eUICC, but can be also performed using other transport protocols.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox participant “Initiator” as INI #FFFFFF participant “SM-SR” as SR #FFFFFF participant “SM-DP” as DP #FFFFFF participant “Operator” as OP #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox INI->>SR: (1) Request for Master Delete \n(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>INI: Failed ||| SR->>DP: (3) Request for Master Delete Authorisation

group Authorisation Hnote over DP, OP #FFFFF Requests authorisation (out of scope) Endhnote Rnote over DP #FFFFF (4) Check if the request is authorised and authenticated Endrnote end DP-->>SR: Refuse SR-->>INI: Refuse DP->>SR: (5) Master Delete Authorisation response\n (Delete Token) SR->>ISDR: (6) MT-SMS [ES5.MasterDelete command](Delete Token) Rnote over ISDR #FFFFF (7) Check conditions Endrnote ISDR-->>SR: Failed SR-->>INI: Failed Rnote over ISDR, ISDP #FFFFF (8) ISD-P verifies the Token and ISD-R deletes ISD-P and contained profile Endrnote ISDR-->>SR: (9) MO-SMS [ES5.MasterDelete command response] Rnote over SR #FFFFFF (10) Update EIS Endrnote SR-->>INI: (11) Profile deletion result @enduml

Figure 25: Master Delete

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1], plus:

c)The target Profile has been verified not to be the Profile which has the Fall- Back Attribute set.

Procedure: (1) The Initiator SHALL send a Master Delete request to the SM-SR containing at least ICCID and EID (the function used in this step is not covered in this specification). (2) The SM-SR SHALL verify that the request is acceptable (at least the preconditions are satisfied). If any of the verifications fails, the SM-SR SHALL return a response indicating the failure, and the procedure SHALL end. (3) SM-SR SHALL send a request for Master Delete authorisation to the SM-DP, which is associated with the target Profile (the function used in this step is not covered in this specification). (4) SM-DP SHALL verify that the request is authenticated and authorised. The SM-DP also requests authorisation from the Operator owner of the target Profile.

NOTE:The definition of this interface is out of the scope of this document.

 If the verification of the request from the SM-SR fails, or if the Operator does not give its
authorisation, the SM-DP SHALL return that the deletion of target Profile is not allowed,
and the procedure SHALL end.
(5) If deletion of the Profile is allowed, a delete token as defined in section 4.1.1.6, SHALL be
   returned to the SM-SR.
(6) The SM-SR SHALL send an MT-SMS containing the “ES5.MasterDelete” command with
   its relevant input data (see section 4.1.1.6) to the ISD-R. The SM-SR SHALL request a
   PoR to get the execution status of the “ES5.MasterDelete” command.
(7) The ISD-R SHALL execute the function as described in section 4.1.1.6. In case of an error,
   a response indicating the failure SHALL be returned (step 9) to the SM-SR and the
   procedure SHALL end.
(8) The ISD-P SHALL verify the token and if successful, the ISD-R SHALL delete the targeted
   ISD-P and the contained Profile.
(9) The ISD-R SHALL return the MO-SMS containing the execution status of the
   “ES5.MasterDelete” command to the SM-SR.
(10)  In case of successful execution, the SM-SR SHALL update the EIS to reflect the
   deleted Profile.
(11)    Finally, the SM-SR SHALL return the response to the Master Delete request to the
   Initiator (the function used in this step is not covered in this specification).

NOTE 1:The MT SMS and MO-SMS SHALL be secured according to section 2.4.

NOTE 2:The token SHALL be usable only once.

3.11 POL2 Update Via SM-DP

This procedure is used by the Operator to update POL2 via the SM-DP.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF

OP->>DP: (1) UpdatePolicyRules(POL2) DP->>SR: (2) UpdatePolicyRules(POL2) Rnote over SR #FFFFF (3) Update POL2 Endrnote SR-->>DP: (4) UpdatePolicyRules Result SR->>M2MSP: (5) Cond: HandleProfilePOL2UpdatedNotification (eid, iccid, POL2) DP-->>OP: (6) UpdatePolicyRules Result @enduml

Figure 26: POL2 Update Via SM -DP

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure: (1) The Operator owner of the target Profile SHALL call the “ ES2.UpdatePolicyRules” function with its relevant input data, as described in section 5.3.3, in particular the identification of the SM-SR in charge of the management of the target eUICC. (2) The SM-DP SHALL forward the request to the SM-SR identified by the Operator and SHALL call the “ES3.UpdatePolicyRules” function with its relevant input data, as described in section 5.4.6 (3) The SM-SR SHALL update the POL2 of the targeted eUICC’s EIS. (4) The SM-SR SHALL return the execution status of the “ES3.UpdatePolicyRules” to the SM-DP. (5) The SM-SR SHALL send the "ES4.HandleProfilePOL2UpdatedNotification" to a M2M SP, if authorised by Operator owning the Profile, indicating the updated POL2 rules according to chapter 5.1.1.2.2.

   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   the Operator owning the Profile, the SM-SR SHALL send this notification to this other
   Operator by calling the “ES4.HandleProfilePOL2UpdatedNotification”.
   If the M2M SP is another Operator connected through its SM-DP and it is authorised by
   the Operator owning the Profile, the SM-SR SHALL send this notification to the SM-DP
   associated       to      this       other    Operator       by        calling     the
   “ES3.HandleProfilePOL2UpdatedNotification”.
    Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting
    as the M2M SP, by calling the “ES2.HandleProfilePOL2UpdatedNotification”
(6) Finally, the SM-DP SHALL return the execution status of the “ES2.UpdatePolicyRules”
    command to the Operator.

3.12 POL1Update by Operator

This procedure allows the Update of POL1 by the Operator via the ES6 interface. For updating the POL1, the Operator SHALL use its OTA Keys hosted in the MNO-SD.

The procedure illustrates the usage of SMS as a possible transport protocol between the Operator and eUICC, but can be also performed using other transport protocols.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox participant “Operator” as OP #FFFFFF box “eUICC” #FFFFFF participant “MNO-SD” as MNO #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox OP->>MNO: (1) MT-SMS [POL1UpdateByMNO command]SCP80 (POL1) ||| MNO->>ISDP: (2) POL1 Update command (POL1) Rnote over ISDP #FFFFF (3) ISD-P Update POL1 Endrnote ISDP-->>MNO: (4) POL1 Update command response ||| MNO-->>OP: (5) MO-SMS [POL1UpdateByMNO command response]SCP80 @enduml

Figure 27: POL1 Update Via Operator

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure: (1) The Operator owning the target Profile SHALL send a MT -SMS containing the “ES6.UpdatePOL1byMNO” function with its relevant input data (as described in section 4.1.2.1). (2) The MNO-SD receives this request and SHALL transfer it to the ISD-P with POL1 as input data. (3) The ISD-P SHALL process POL1 update of the target profile. (4) The ISD-P SHALL return the execution status of the “ES6.UpdatePOL1byMNO” to MNO- SD. (5) Finally, the MNO-SD SHALL return the MO-SMS containing the execution status of the “ES6.UpdatePOL1byMNO” command to the Operator.

NOTE:The MT-SMS and MO-SMS SHALL be secured according to section 2.7.

NOTE2:If the ISD-P and its target profile has the Fall-Back Attribute set, POL1 with “Profile deletion is mandatory when it is disabled” set in this profile, then this POL1 rule will be ignored according to Sections 2.4 and 3.6.3.2 in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

3.13 Connectivity Parameters Update by Operator

This procedure allows the update of the Connectivity Parameters by the Operator on the ES6 interface.

The procedure illustrates the usage of SMS as a possible transport protocol between the Operator and eUICC, but can be also performed using other transport protocols.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox participant “Operator” as OP #FFFFFF box “eUICC” #FFFFFF participant “MNO-SD” as MNO #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox OP->>MNO: (1) MT-SMS [Connectivity Parameters]SCP80 ||| MNO->>ISDP: (2) Connectivity Parameters Update command Rnote over ISDP #FFFFF (3) ISD-P Update Connectivity Parameters Endrnote ISDP-->>MNO: (4) Connectivity Parameters Update response ||| MNO-->>OP: (5) MO-SMS [Connectivity Parameters Update command response]SCP80 @enduml

Figure 28: Connectivity Parameters Update by Operator

Start condition: The Operator wants to update the Connectivity Parameters in their Profile

Procedure: (1) The Operator owning the target Profile SHALL send a MT -SMS containing the Connectivity Parameters to the MNO-SD. (2) The MNO-SD SHALL transfer the Connectivity Parameters to the ISD-P. (3) The ISD-P SHALL update the Connectivity Parameters. (4) The ISD-P SHALL return the execution status to the MNO-SD. (5) The MNO-SD SHALL send the MO-SMS containing the execution status to the Operator.

NOTE:The MT-SMS and MO-SMS SHALL be secured according to section 2.7.

3.14 Connectivity Parameters Update Using SCP03

This procedure allows the update of the Connectivity Parameters using SCP03by the SM-DP on the ES8 interface. The procedure illustrates the usage of SMS as a possible transport protocol between the SM- SR and eUICC, where ISD-R is in charge of encapsulating the data in SCP80,. Other transport protocols such as HTTPS or CAT-TP can be used.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox participant “Operator/SM-DP” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF participant “ISD-P” as ISDP #FFFFFF endbox OP->>SR: (1) UpdateConnectivityParametersSCP03\nCommand(Connectivity Parameters SCP03) SR->>ISDR: (2) MT-SMS [Connectivity Parameters SCP03]SCP80 ISDR->>ISDP: (3) (Connectivity Parameters SCP03) Rnote over ISDP #FFFFF (4) ISD-P Update Connectivity Parameters Endrnote ISDP-->>ISDR: (5) Connectivity Parameters Update response ||| ISDR-->>SR: (6) MO-SMS [Connectivity Parameters Update command response]SCP80 SR-->>OP: (7) UpdateConnectivityParametersSCP03 Result @enduml

Figure 29: Connectivity Parameters Update Using SCP03

The start conditions are described in [1]. (1) The Operator, or the SM-DP, on behalf of the Operator owning the target Profile, SHALL send a request containing “ES3.UpdateConnectivityParameters” function with its relevant input data (as described in section 5.4.6). The <data> parameter SHALL contain an SCP03 script as defined in section 4.1.3.2 including the command “ES8.UpdateConnectivityParametersSCP03”

(2) The SM-SR SHALL send a ciphered MT-SMS using SCP80 containing the ciphered data
    provided by the SM-DP, to the ISD-P TAR according to section 2.5.
(3) The ISD-R SHALL transfer the <data> to the ISD-P.
(4) The ISD-P SHALL update the Connectivity Parameters.
(5) The    ISD-P    SHALL      return   the      execution               status      of      the
    “ES8.UpdateConnectivityParametersSCP03” to ISD-R.
(6) The ISD-R SHALL send the ciphered MO-SMS containing the execution status of the
    “ES8.UpdateConnectivityParametersSCP03” command to the SM-SR. This execution
    status is sent from the ISD-P TAR and the ISD-R SHALL apply the security through the
    SCP80 to this MO-SMS.
(7) Finally, the  SM-SR     SHALL     return the     execution              status     of    the
    “ES3.UpdateConnectivityParameters” command to the SM-DP.

NOTE:The MT-SMS and MO-SMS SHALL be secured according to section 2.2.5

3.15 Default Notification Procedure

This section provides a default notification procedure from the eUICC to the SM-SR. This
default notification carries information about the eUICC and the Device .
This notification is initiated by the eUICC in some conditions:
    First network attachment of the Device: this indicates to the SM-SR in charge of
       managing of the eUICC that the eUICC has been deployed on the field. The
       notification of “First network attachment” happens only once in the eUICC’s lifetime. It
       is triggered when the eUICC is network attached the very first time. Nevertheless,
       note that this notification will be retried until the effective reception by the SM-SR,
       including further network attachments if not succeeded during the first network
       attachment session.
    After an explicit new Profile Enabling request: this indicates to the SM-SR which is
       the Profile which is currently enabled. This notification happens right after the network
       attachment:
        With the newly Enabled Profile in case of successful attachment
        Or with the previously Enabled Profile or with the Profile having the Fall-Back
            Attribute, after the attachment with the requested Profile has failed.
    After activation of the Fall-Back Mechanism: this indicates to the SM-SR that the
       Profile with the Fall-Back Attribute has been enabled. This notification happens right
       after the network attachment.
The notification may happen either on SMS, CAT_TP or HTTPS. The content of the notification
message is the same whatever protocol is used. The eUICC is free to select the most relevant
protocol according to the Device’s capabilities.
The notification has to be confirmed by the SM-SR. The confirmation will depend on the
protocol used for notification.
On reception of the SM-SR notification confirmation, the eUICC may perform any operation
as specified in one of the procedures including the notification sequence (like for instance
deletion of an ISD-P after its disabling, see section 3.6). After the eUICC has performed the
follow-up activities, the eUICC SHALL respond to the SM-SR notification confirmation
function, including the identification of the operation performed if any.

3.15.1 Notification Using SMS

This figure describes the notification sequence over SMS. It is applicable either for first “power on” of the Device, or the enabling of a Profile (after explicit request or Fall-Back Mechanism).

SM-SR                                           Device                    eUICC
Network attachment           (1) Detect:
Event                        -First “Power on”
                             -Change of enabled profile
(2) Send MO-SMS [ SCP80-CP[data] ]     Sequence is retried until
                                       getting the TR=0 or a
                                       max retry attempt           Sequence is retried
          Terminal response success,   number reached              until getting
          TR=0                                                     Confirmation or a
                                                                   max retry attempt
                                         (2a)Wait for              number reached
                                         Confirmation
(3) Process notification
             (4) Send MT-SMS [ SCP80-CP[ [ES5.NotificationConfirmation command] ] ]

(5) Unwrap SCP80

                                                                         (6) Process Confirmation
(7) Send MO-SMS [ SCP80-CP[ES5.NotificationConfirmation response] ]

Figure 30: Sequence Flow of Notification Over SMS

(1) At the end of the start-up sequence, the eUICC detects a first “power on” or a situation
   where the Enabled Profile has changed compared to the previous eUICC reset.
(2) The eUICC sends an MO-SMS envelop. The SMS contains a secure SCP 80 Command
   Packet (MO-SMS SHALL be formatted as defined in section 2.4.3 with security set to
   cryptographic checksum and no ciphering, the counter value of the Command Packet
   SHALL be set to ‘0000000000’ and SPI set to “No counter available”) using the SCP80
   keys of the ISD-R, and containing the notification data structure described in section
   4.1.1.11. The secured data SHALL be coded as described in section 4.1.1.11.
   NOTE:              This deviates from the typical secured packets generation defined in ETSI TS
                      102 225 [4].
       The eUICC SHALL use the network information of the Enabled Profile, and the
       addressing information configured for this profile in ISD-R. If there is no addressing
       information configured for this profile in ISD-R, the global addressing information
       configured in ISD-R SHALL be used.

NOTE:This allows using an internal address (network specific number) for the connection of the SM-SR Platform to the SMSC.

The eUICC SHALL retry sending until getting a successful response of the Device (‘0X’).
Note, that the eUICC SHALL implement a mechanism to avoid attempting an infinite
number of retries. Finally the eUICC SHALL use another protocol in case of final failure
for sending the notification using SMS.
(2a)     The eUICC SHALL wait for the SM-SR confirmation. If no confirmation is received by
         the eUICC after a certain amount of time (dependent on the configuration), eUICC
         SHALL restart from step (2) (with the same sequence number).
(3) The SM-SR processes the notification.
(4) The SM-SR sends an MT-SMS containing the “ES5. HandleNotificationConfirmation”
   command defined in section 4.1.1.12 in a SCP80 command packet. This MT-SMS SHALL
   target the entity on the eUICC that has sent the notification.
(5) The ISD-R un-wraps the SCP80 security layer
(6) The eUICC processes the notification confirmation data; this may include follow-up
   activities as required by the procedure where this sequence is used.
(7) The eUICC     SHALL return the MO-SMS containing the response of the
   “ES5.HandleNotificationConfirmation” command. The MO-SMS SHALL be secured
   according to section 2.4.3. The eUICC SHALL retry sending until getting a successful
   response of the Device (‘0X’). Note, that the eUICC SHALL implement a mechanism to
   avoid attempting an infinite number of retries.

3.15.2 Notification Using HTTPS

This figure describes the notification sequence over HTTPS. It is applicable either for first “power on” of the Device, or the enabling of a Profile (after explicit request or Fall-Back Mechanism).

SM-SR                                                  Device                           eUICC
                                                              Network Attachment Event            (1)Detect:
                                                                                                 -First “Power on”
                                                                                                 -Change of enabled profile
(2) Conditional: DNS resolution to retrieve IP address of SM-SR
(3) OPEN CHANNEL (parameters)
             TR=OK
                    (4) PSK-TLS handshake
                                                                               Sequence is retried
                                                                               until getting HTTP
POST <SM-SR initial uri> ?msg=data HTTP/1.1 CRLF
                                                                               response or a max
Host: <SM-SR ip> CRLF                                                    (5)   retry attempt
X-Admin-Protocol: globalplatform-remote-admin/1.0 CRLF
                                                                               number reached
X-Admin-From://host-id/eid/<value>;//ag-id/aid/<ISD-R-AID value> CRLF
CRLF

(6) Process notification

         HTTP/1.1 200 CRLF
(7)      X-Admin-Protocol:globalplatform-remote-admin/1.0 CRLF
         CRLF
         <Body with ES5.NotificationConfirmation>
                                                                                         (8) Process Notification
         POST /<next-uri> HTTP/1.1 CRLF
         …                                                                        (9)
         X-Admin-Script-Status: <script-status> CRLF
         CRLF
         <Body with ES5.NotificationConfirmation response>
         HTTP/1.1 204 CRLF
(10)     X-Admin-Protocol:globalplatform-remote-admin/1.0 CRLF
         CRLF

Figure 31: Sequence Flow of Notification Over HTTPS

(1) At the end of the start-up sequence, the eUICC detects a first “power on” or a situation
    where the Enabled Profile has changed compared to the last eUICC reset.
(2) If DNS resolution is supported and correctly configured on the eUICC, the ISD -R MAY
    request a DNS resolution first to retrieve the IP Address(es) of the SM-SR, as defined in
    section 2.4.5.
(3) The eUICC opens a BIP channel with the relevant parameters to address the SM-SR. This
    includes having access to the Network Access Name, User Login and User Password of
    the Enabled Profile.
(4) The ISD-R of the eUICC negotiates the PSK-TLS handshake with the SM-SR. The TLS
    session SHALL be opened as defined in section 2.4.3. The ISD-R SHALL apply the retry
    Policy as defined in GlobalPlatform Card Specification Amendment B [8].
(5) The eUICC sends the first HTTP POST. The notification contains the SM-SR URL with the
    special query parameter “?msg” containing the data for eUICC notification defined in
    section 4.1.1.11. The data of the notification SHALL be coded as hexadecimal string (see
    section 5.1.1.1) with no spaces.
              a. The ISD-R SHALL apply the retry Policy as defined in GlobalPlatform Card
                 Specification Amendment B [8].
(6) The SM-SR processes the notification
(7) The SM-SR SHALL return an HTTP response with a body containing the “ ES5.
   HandleNotificationConfirmation” command acknowledging the reception of the
   notification.
(8) The eUICC processes the notification confirmation; this may include follow-up activities as
   required by the procedure where this sequence is used.
(9) The  eUICC      SHALL   return the   execution response of the  “ ES5.
   HandleNotificationConfirmation” command within a new HTTP POST request
   addressed to the SM-SR.
(10)   The SM-SR SHALL return an HTTP response “204 No content”.

3.16 Fall-Back Activation Procedure

The Fall-Back Mechanism SHALL be activated in case of loss of network connectivity by the current Enabled Profile. The eUICC SHALL disable the current Enabled Profile and enable the Profile with Fall-Back Attribute set.

If the current enabled Profile is the Emergency Profile or the Test Profile, the eUICC SHALL NOT activate the Fall-Back Mechanism, until the Local Disable command is called.

@startuml skinparam monochrome true skinparam ArrowColor Black hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “SM-SR” as SR #FFFFFF participant Device #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox

rnote over ISDR (1) Triggering Fall-Back Mechanism End rnote

rnote over ISDR (2) Disable current Profile. Enable Fall-Back Profile. End rnote

ISDR->>Device: (3) REFRESH (UICC reset)

Hnote right of Device #C0C0C0 (4) Network attach with the enabled profile End hnote

Hnote over SR, ISDR #C0C0C0 (5) Notification procedure End hnote

Rnote over SR (6) EIS Update End rnote

SR->OP2: (7) Cond: handleProfileEnabledNotification(eid, iccid2) SR->OP1: (8) Cond: handleProfileDisabledNotification(eid, iccid) SR->>M2MSP: (9) Cond: HandleProfileEnabledNotification (eid, iccid2) SR->>M2MSP: (10) Cond: HandleProfileDisabledNotification (eid, iccid)

@enduml

Figure 32: Fall-Back Activation Procedure

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1]

The profile with Fall-Back Attribute set has already been installed and is in disabled state.

Procedure:
(1) The Fall-Back Mechanism is triggered in accordance with the Start Conditions.
(2) Ignoring POL1 of the Enabled Profile, the ISD-R SHALL disable the currently Enabled
   Profile and SHALL enable the Profile with the Fall-Back Attribute set.
(3) The ISD-R SHALL request the Device to perform the toolkit REFRESH command in UICC
   Reset mode. This will trigger the execution of the network attach procedure.
(4) The eUICC and the Device SHALL perform a new network attach procedure.
(5) The eUICC SHALL perform the notification procedure as described in section 4.1.1.11.
   The ISD-R SHALL ensure that all supported Default Notification mechanism will be used
   to inform SM-SR about the activation of the Fall-Back Mechanism. After having exhausted
   all possible retries to inform the SM-SR, the eUICC SHALL stay in this state and continue
   trying to notify the SM-SR. On reception of the notification, the SM-SR is informed that the
   Fall-Back Mechanism was triggered and the last Enabled Profile has been disabled.
           a. If the previously Enabled Profile contains the rule "Profile deletion is mandatory
               when its state is changed to disabled", the eUICC SHALL NOT automatically
               delete this Profile.
(6) The SM-SR SHALL update the EIS to reflect that:
     The Profile having the Fall-Back Attribute set has been enabled
     The previously Enabled Profile has been disabled
(7) Unless Operator1 has set an ONC to not receive those notifications, the SM-SR SHALL
    send the “ES4.HandleProfileEnabledNotification” to Operator2, the owner of Profile with
    the Fall-Back Attribute set that is now enabled. In case Operator2 has no direct connection
    with the SM-SR (SM-SR SHALL be able to detect such situation based on its own
   database), the SM-SR SHALL send this notification to the SM-DP that acts on behalf of
   Operator2 by calling the “ES3.HandleProfileEnabledNotification”. The SM-SR can
   retrieve the SM-DP identity based on the EIS content. Then the SM-DP, on reception of
   this    notification, SHALL     forward    it   to    Operator2 by     calling   the
   “ES2.HandleProfileEnabledNotification”.
(8) Unless Operator1 has set an ONC to not receive those notifications, thehe SM-SR SHALL
   send the “ES4.HandleProfileDisabledNotification” to Operator1, the owner of the Profile
   that was enabled at the beginning of the procedure. In case Operator1 has no direct
   connection with the SM-SR (SM-SR SHALL be able to detect such a situation based on
   its own database), the SM-SR SHALL send this notification to the SM-DP that acts on
   behalf of Operator1 by calling the “ES3.HandleProfileDisabledNotification”. The SM-SR
   can retrieve the SM-DP identity based on the EIS content. Then the SM-DP, on reception
   of this notification, SHALL           forward it to Operator1 by calling the
   “ES2.HandleProfileDisabledNotification”.
(9) The SM-SR SHALL send the "ES4.HandleProfileEnabledNotification" to an M2M SP, if
   authorised by Operator2 who owns the Profile with Fall-Back Attribute set that is now
   enabled.
     If the M2M SP is another Operator directly connected to the SM-SR and it is
     authorised by Operator2, the SM-SR SHALL send this notification to this other
     Operator by calling the “ES4.HandleProfileEnabledNotification”.
If the M2M SP is another Operator connected through its SM-DP and it is authorised
by Operator2, the SM-SR SHALL send this notification to the SM-DP associated to this
other Operator by calling the “ES3.HandleProfileEnabledNotification”.
Then the SM-DP, on reception of this notification, SHALL forward it to the Operator,
acting as the M2M SP, by calling the “ES2.HandleProfileEnabledNotification”.
(10)   The SM-SR SHALL send the "ES4.HandleProfileDisabledNotification" to an M2M
   SP, if authorised by Operator1 who owns the Profile that was enabled at the beginning of
   the procedure.
If the M2M SP is another Operator directly connected to the SM-SR and it is authorised
by Operator1, the SM-SR SHALL send this notification to this other Operator by calling
the “ES4.HandleProfileDisabledNotification”.
If the M2M SP is another Operator connected through its SM-DP and it is authorised by
Operator1, the SM-SR SHALL send this notification to the SM-DP associated to this
other Operator by calling the “ES3.HandleProfileDisabledNotification”.
Then the SM-DP, on reception of this notification, SHALL forward it to the Operator,
acting as the M2M SP, by calling the “ES2.HandleProfileDisabledNotification”.

NOTE:This M2M SP might be the same M2M SP as for Operator1 or any other M2M SP.

If the previously Enabled Profile has the POL1 rule “disable not allowed” or “Profile deletion is mandatory when its state is changed to disabled” set, then:

    the eUICC SHALL only switch back to this Profile
    The eUICC SHALL prevent the execution of the function “Set Fall-Back Attribute”
     it SHALL only be possible to delete this Profile by the Master Delete function.

NOTE:A mechanism MAY permit to request to the eUICC to switch back to the previously enabled profile once the network connectivity has been restored. In this case, after network attachment to the previously Enabled profile succeeds, the eUICC SHALL perform the notification procedure as described in section 4.1.1.11. The ISD-R SHALL ensure that all supported Default Notification mechanism will be used to inform SM-SR that the previously enabled profile has been enabled again. After having exhausted all possible retries to inform the SM-SR, the eUICC SHALL continue trying to notify the SM-SR. On reception of the notification, the SM-SR is informed that the Fall-Back Mechanism is cancelled, and SHALL update the EIS to reflect the new Enabled and Disabled profiles.

The technical solution of the cancellation of the Fall-Back Mechanism mentioned above is out of scope.

3.17 Profile Enabling via M2M SP

The Profile Enabling procedure between the M2M SP and the SM-SR is used to enable a Profile previously downloaded and installed on an eUICC (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.16). The procedure is initiated by the M2M SP, based on prior authorisation of the Operator owning the Profile to be enabled, as defined in section 3.20. The procedure illustrates the usage of SMS as a possible transport protocol between SM-SR and eUICC, but can also be performed using other transport protocols.

3.17.1 Normal Case

The sequence flow in the figure below describes the normal case where the target Profile can successfully be enabled.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox

M2MSP->>SR: (1) EnableProfile(eid, iccid)
Rnote over SR #FFFFF
(2) Check initial conditions
Endrnote
SR-->> M2MSP: Failed
SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80
Rnote over ISDR #FFFFFF
(4) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80
SR-->> M2MSP: Failed
Rnote over ISDR #FFFFFF
(5) Enable ISD-P
Endrnote
ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80
SR-->> M2MSP: (6a) Failed
ISDR-->>DEV: (7) REFRESH, (UICC reset)
Rnote over DEV, ISDR #FFFFFF
(8) Network attachment with the enabled profile
Endrnote
|||
Hnote right of SR #FFFFFF
(9)                  Notification procedure over SMS
Endhnote
|||
Rnote over SR #FFFFFF
(10) Check POL2
Endrnote
SR->>ISDR: (11) Cond.: MT-SMS [ES5.DELETE command]SCP80
Rnote over ISDR #FFFFFF
(11a) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.DELETE command FAILED response]SCP80
SR-->>M2MSP: Failed
Rnote over ISDR #FFFFFF
(11b) Delete disabled ISD-P
and contained profile
Endrnote
ISDR-->>SR: (11c) MO-SMS [ES5.DELETE command response]SCP80
Rnote over SR #FFFFFF
(12) Update EIS
Endrnote
SR-->>M2MSP: (13) Profile enabling result
SR->>OP1: (14) Cond: HandleProfileEnabledNotification (eid, iccid)
SR->>OP2: (15) Cond: HandleProfileDisabledNotification(eid2, iccid2)
SR->>M2MSP: (16) Cond: HandleProfileDisabledNotification(eid 2, iccid2)

@enduml

Figure 33: Profile Enabling via M2M SP, Success Case

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure: (1) To enable the targeted Profile of Operator1 the M2M SP SHALL call the “ES4.EnableProfile” function with its relevant input data. (2) The SM-SR SHALL verify that the M2M SP request is acceptable (the verifications that the SM-SR SHALL perform are described in the section 5.5.5), and in particular checks that the M2M SP has the authorisation to enable the targeted profile, and evaluates POL2 of the currently Enabled Profile. If any of the conditions to be verified are not satisfied, the SM-SR SHALL return a response indicating the failure, and the procedure SHALL end. (3) The SM-SR SHALL send an MT-SMS containing the “ES5.STORE DATA” command for Profile enabling with its relevant input data (see section 4.1.1.2) to the ISD-R. The SM-SR SHALL request a PoR to get the execution status of the “ ES5.STORE DATA” command. (4) The ISD-R SHALL enforce POL1 of the currently Enabled Profile. If POL1 rejects enabling of the target Profile, the ISD-R SHALL return directly the MO-SMS containing the response indicating a failure, and the procedure SHALL end. (5) If POL1 allows, the ISD-R SHALL disable the currently enabled ISD-P and enable the targeted ISD-P.

NOTE:Profile change includes a change of the IMSI that is used to attach to the network. As indicated in 3GPP TS 31.102 [52], such a change requires special caution and should always be accompanied by a REFRESH command to avoid inconsistent information being read by the terminal. So while the targeted ISD-P is marked as enabled in this step, it MAY actually become effective after the terminal executes the REFRESH command.

(6) The ISD-R SHALL return the MO-SMS containing the execution status of the “ES5.STORE
   DATA” command to the SM-SR.
(6a)   If the response to the “ES5.STORE DATA” command indicates a failure, the SM-SR
       SHALL return a response indicating the failure to M2M SP, and the procedure SHALL
       end.
(7) The ISD-R SHALL send a REFRESH proactive command in UICC reset mode to the
   Device. This will trigger the execution of a network attach procedure.
   NOTE:       In case of any error after this step, indicating that the currently Enabled
               Profile cannot provide connectivity, the ISD-R SHALL re-enable the
               previously Enabled Profile as described in section 3.2.2.
(8) The eUICC and the Device SHALL perform a network attach procedure with the newly
   Enabled Profile.
(9) The eUICC SHALL perform the notification procedure as described in section 4.1.1.11.
   During this procedure, if the ISD-R doesn’t succeed in sending the SMS notification (after
   having exhausted all possible retries), or doesn’t receive the SM-SR notification
   confirmation, this SHALL be considered as a fatal error, and the previous note SHALL
   apply. On reception of the SM-SR notification confirmation command, if POL1 of the now
   Disabled Profile contains the rule “Profile deletion is mandatory when it is disabled”, and
   this Profile does not have the Fall-Back Attribute set, the ISD-R SHALL delete the disabled
   ISD-P and the contained Profile. The eUICC SHALL send the response to the notification
   confirmation indicating whether the disabled ISD-P has been deleted or not.
(9a)   If the previously Enabled Profile (now Disabled) has the Fall-Back Attribute, and its
       POL1 contains the rule “Profile deletion is mandatory when its state is changed to
       disabled”, this rule SHALL be ignored according to Sections 2.4 and 3.6.3.2 in GSMA
       Remote Provisioning Architecture for the Embedded UICC [1], and the procedure
       SHALL continue at step 10.
(10)   On reception of the “ES5.HandleNotificationConfirmation” response, and if this
   response indicates that the Disabled Profile has not been deleted, the SM-SR SHALL
   evaluate POL2 of the Disabled Profile. If POL2 of the Disabled Profile contains the rule
   “Profile deletion is mandatory when it is disabled”, the SM-SR SHALL perform step (11),
   else it SHALL jump to step (12).
(11)    The SM-SR SHALL send an MT-SMS containing the “ES5.DELETE” command with
   its relevant input data (see section 4.1.1.4) to the ISD-R, targeting the Disabled Profile.
   The SM-SR SHALL request a PoR to get the execution status of the “ ES5.DELETE”
   command.
(11a) The ISD-R SHALL enforce POL1 of the target Profile. If POL1 rejects the deletion of
      the target Profile, the ISD-R SHALL return the MO-SMS containing the response
      indicating the corresponding failure, and the procedure SHALL end.
(11b) If POL1 allows its deletion, the ISD-R SHALL delete the targeted ISD-P and the
      contained Profile.
(11c) The ISD-R SHALL return the MO-SMS to the SM-SR containing the execution status
      of the “ES5.DELETE” command.
(12)  According to the executed sequence and the eUICC responses, the SM-SR SHALL
   update the EIS to reflect that:
      The target Profile has been enabled
      The previously Enabled Profile has been disabled or deleted.

NOTE:POL1 and POL2 MAY have different content. As a consequence, both the eUICC and the SM-SR have to ensure the ISD-P deletion based on their respective Policy.

(13) The SM-SR SHALL return the response to the “ES4.EnableProfile” function to the
   M2M SP, indicating that the Profile has been enabled.
(14)    Unless Operator1 has set an ONC to not receive those notifications, the SM-SR
   SHALL send the “ES4.HandleProfileEnabledNotification” to Operator1, the owner of the
   Profile that was disabled at the beginning of the procedure. In case Operator1 has no
   direct connection with the SM-SR (SM-SR SHALL be able to detect such a situation based
   on its own database), the SM-SR SHALL send this notification to the SM-DP authorised
   by Operator1 by calling the “ES3.HandleProfileEnabledNotification”. The SM-SR can
   retrieve the SM-DP identity based on the EIS content. Then the SM-DP, on reception of
   this    notification, SHALL      forward    it   to   Operator1 by       calling    the
   “ES2.HandleProfileEnabledNotification”.
(15)   Unless Operator1 has set an ONC to not receive those notifications, the SM-SR
   SHALL          send       the        “ES4.HandleProfileDisabledNotification”          or
   “ES4.HandleProfileDeletedNotification” (if deletion was triggered by the evaluation of
   POL1 and POL2) to Operator2, the owner of the Profile that was enabled at the beginning
   of the procedure. In case Operator2 has no direct connection with the SM-SR (SM-SR
   SHALL be able to detect such a situation based on its own database), the SM-SR SHALL
   send this notification to the SM-DP authorised by Operator2 by calling the
   “ES3.HandleProfileDisabledNotification”                       or                    the
   “ES3.HandleProfileDeletedNotification”. The SM-SR can retrieve the SM-DP identity
   based on the EIS content. Then the SM-DP, on reception of this notification, SHALL
   forward it to Operator2 by calling the “ES2.HandleProfileDisabledNotification” or the
   “ES2.HandleProfileDeletedNotification”.
(16) The SM-SR SHALL send the “ES4.HandleProfileDisabledNotification” or
   “ES4.HandleProfileDeletedNotification” (if deletion was triggered by the evaluation of
   POL1 and POL2) to a M2M SP, if authorised by Operator2 the owner of the Profile that
   was enabled at the beginning of the procedure.
If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
Operator2, the SM-SR SHALL send this notification to this other Operator by calling the
“ES4.HandleProfileDisabledNotification” or “ES4.HandleProfileDeletedNotification”.
If the M2M SP is another Operator connected through its SM-DP and it is authorised by
Operator2, the SM-SR SHALL send this notification to the SM-DP associated to this other
Operator     by    calling   the      “ES3.HandleProfileDisabledNotification”             or
“ES3.HandleProfileDeletedNotification”.
Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting
as the M2M SP, by calling the “ES2.HandleProfileDisabledNotification” or

“ES2.HandleProfileDeletedNotification”.

NOTE:This M2M SP might be the same M2M SP as for Operator1 or any other M2M SP.

NOTE:The MT-SMS and MO-SMS SHALL be secured according to section 2.4.

3.17.2 Connectivity Failure Case

The sequence flow in the figure below describes the case where the target Profile cannot provide connectivity after it is enabled, and when roll-back to the previously Enabled Profile occurs.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP1 #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox

M2MSP->>SR: (1) EnableProfile(eid, iccid)
Rnote over SR #FFFFF
(2) Check initial conditions
Endrnote
SR-->>M2MSP: Failed
SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80
Rnote over ISDR #FFFFFF
(4) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80
SR-->>M2MSP: Failed
Rnote over ISDR #FFFFFF
(5) Enable ISD-P
Endrnote
ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80
SR-->>M2MSP: (6a) Failed
ISDR-->>DEV: (7) REFRESH, (UICC reset)
Rnote over DEV, ISDR #FFFFFF
(8) Network attachment with the enabled profile **fails**
                                 OR
                    Notification procedure **fails**
Endrnote
|||
Hnote over ISDR #FFFFFF
(9) Enable previous ISD-P
Endhnote
ISDR-->>DEV: (10) REFRESH, (UICC reset)
Rnote over DEV, ISDR #FFFFFF
(11) Network attachment with the enabled profile
Endrnote
|||
Hnote right of SR #FFFFFF
(12)                  Notification procedure over SMS
Endhnote
|||
SR-->>M2MSP: (13) Profile enabling failure
@enduml

Figure 34: Profile Enabling via M2M SP, Failure Case with roll-back

Start Conditions: The start conditions are identical to section 3.17.1

Procedure: Steps (1), (2), (3), (4), (5), (6), (6a) and (7) are also identical to section 3.17.1.

(8) A network attach failure occurs indicating that the Enabled Profile cannot provide
    connectivity, or the eUICC doesn’t succeed to send the SMS notification (after having
    exhausted all possible retries), or doesn’t receive the SM-SR notification confirmation.
(9) The ISD-R SHALL enable the Profile that was previously enabled before the reception of
    the command, to re-establish connectivity.

NOTE:Profile change includes a change of the IMSI that is used to attach to the network. As indicated in 3GPP TS 31.102 [52], such a change requires special caution and should always be accompanied by a REFRESH command to avoid inconsistent information being read by the terminal. So while the targeted ISD-P is marked as enabled in this step, it MAY actually become effective only after the terminal executes the REFRESH command.

(10) The ISD-R sends a REFRESH proactive command in UICC reset mode to the Device. This will trigger the execution of a new network attach procedure. (11) The eUICC and the Device SHALL perform a new network attach procedure with the Profile Enabled before the start of the procedure. (12) The eUICC SHALL perform the notification procedure as described in sectio n 4.1.1.11. On reception of the SMS notification, the SM-SR is informed that the target Profile has not been enabled. (13) Finally, the SM-SR SHALL return the response to the “ES4.EnableProfile” function to the M2M SP; indicating a failure, the target Profile didn’t succeed to provide the connectivity.

3.18 Profile Disabling via M2M SP

The Profile Disabling procedure between the M2M SP and the SM-SR is used to disable a Profile previously downloaded and installed on an eUICC (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.17). The procedure is initiated by the M2M SP, based on prior authorisation of the Operator owning the Profile to be disabled, as defined in section 3.20. The procedure illustrates the usage of SMS as a possible transport protocol between SM-SR and eUICC, but can also be performed using other transport protocols.

The sequence flow in the figure below describes the normal case where the target Profile can successfully be disabled.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator2” as OP2 #FFFFFF participant “Operator1” as OP1 #FFFFFF participant “SM-SR” as SR #FFFFFF participant “Device” as DEV #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox

M2MSP->>SR: (1) DisableProfile(eid, iccid)
Rnote over SR #FFFFF
(2) Check initial conditions
Endrnote
SR-->>M2MSP: Failed
SR->>ISDR: (3) MT-SMS [ES5.STORE DATA command]SCP80
Rnote over ISDR #FFFFFF
(4) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.STORE DATA command Failed response]SCP80
SR-->>M2MSP: Failed
Rnote over ISDR #FFFFFF
(5) Disable ISD-P
Endrnote
ISDR-->>SR: (6) MO-SMS [ES5.STORE DATA command response]SCP80
SR-->>M2MSP: (6a) Failed
ISDR-->>DEV: (7) REFRESH, (UICC reset)
Rnote over DEV, ISDR #FFFFFF
(8) Network attachment using profile with Fall-Back attribute
Endrnote
|||
Hnote right of SR #FFFFFF
(9)                  Notification procedure over SMS
Endhnote
|||
Rnote over SR #FFFFFF
(10) Check POL2
Endrnote
SR->>ISDR: (11) Cond.: MT-SMS [ES5.DELETE command]SCP80
Rnote over ISDR #FFFFFF
(11a) Enforce POL1
Endrnote
ISDR-->>SR: MO-SMS [ES5.DELETE command FAILED response]SCP80
SR-->>M2MSP: Failed
Rnote over ISDR #FFFFFF
(11b) Delete disabled ISD-P
and contained profile
Endrnote
ISDR-->>SR: (11c) MO-SMS [ES5.DELETE command response]SCP80
Rnote over SR #FFFFFF
(12) Update EIS
Endrnote
SR-->>M2MSP: (13) Profile disabling result
SR->>OP1: (14) Cond: HandleProfileDisabledNotification(eid, iccid )
SR->>OP2: (15) Cond: HandleProfileEnabledNotification(eid, iccid2)
SR->>M2MSP: (16) Cond: HandleProfileEnabledNotification(eid, iccid2)
@enduml

Figure 35: Profile Disabling via M2M SP

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure: (1) To disable the targeted Profile of Operator1 the M2M SP SHALL call the “ES4.Disable.Profile” function with its relevant input data. (2) The SM-SR SHALL verify that the M2M SP request is acceptable (the verifications that the SM-SR SHALL perform are described in the section 5.5.6, and in particular checks that the targeted Profile is enabled, that the M2M SP has the authorisation to disable the targeted profile, and that Profile disabling is allowed in POL2. If any of the conditions to be verified are not satisfied, the SM-SR SHALL return a response indicating the failure, and the procedure SHALL end. (3) The SM-SR SHALL send an MT-SMS containing the “ES5.STORE DATA” command for Profile disabling with its relevant input data (see section 4.1.1.3) to the ISD-R. The SM-SR SHALL request a PoR to get the execution status of the “ ES5.STORE DATA” command. (4) The ISD-R SHALL enforce POL1 of the currently Enabled Profile. In case POL1 rejects disabling, the ISD-R SHALL return PoR containing the response indicating a failure, and the procedure SHALL end.

(5) The ISD-R SHALL disable the targeted ISD-P and the contained Profile and SHALL enable the Profile with the Fall-Back Attribute set.

NOTE:Profile change includes a change of the IMSI that is used to attach to the network. As indicated in 3GPP TS 31.102 [52], such a change requires special caution and should always be accompanied by a REFRESH command to avoid inconsistent information being read by the terminal. So while the targeted ISD-P is marked as enabled in this step, it MAY actually become effective only after the terminal executes the REFRESH command.

(6) The ISD-R SHALL return the MO-SMS containing the execution status of the “ES5.STORE
   DATA” command to the SM-SR.
(6a)    If the response to the “ES5.STORE DATA” command indicates a failure, the SM-SR
        SHALL return a response indicating the failure to M2M SP, and the procedure SHALL
        end.
(7) The ISD-R sends a REFRESH proactive command in UICC reset mode to the Device.
   This will trigger the execution of a network attach procedure.

NOTE:In case of any error after this step indicating that the curr ent Enabled Profile cannot provide connectivity, the ISD-R SHALL re-enable the previously Enabled Profile as described in section 3.2.2.

(8) The eUICC and the Device SHALL perform a new network attach procedure with the
   Profile with the Fall-Back Attribute set.
(9) The eUICC SHALL perform the notification procedure as described in section 4.1.1.11.
   During this procedure, if ISD-R doesn’t succeed to send the SMS notification, or doesn’t
   receive the SM-SR notification confirmation, this SHALL be considered as an error, and
   the previous note SHALL apply.
       On reception of the SM-SR notification confirmation command, if POL1 of the Disabled
       Profile contains the rule “Profile deletion is mandatory when it is disabled”, the ISD-R
       SHALL delete the disabled ISD-P and the contained Profile. The eUICC SHALL send
       the response to the notification confirmation indicating whether the disabled ISD -P has
       been deleted or not.
(10)   On reception of the ES5.HandleNotificationConfirmation response, and if the
   ES5.HandleNotificationConfirmation response indicates that the Disabled Profile has
   not been deleted, the SM-SR SHALL evaluate POL2 of the Disabled Profile. If POL2 of
   the Disabled Profile contains the rule “Profile deletion is mandatory when it is disabled”,
   the SM-SR SHALL perform step (11), else it SHALL jump to step (12).
(11)    The SM-SR SHALL send an MT-SMS containing the “ES5.DELETE” command with
   its relevant input data (see section 4.1.1.4) to the ISD-R, targeting the Disabled Profile.
   The SM-SR SHALL request a PoR to get the execution status of the “ ES5.DELETE”
   command.
(11a) The ISD-R SHALL enforce POL1 of the target Profile. If POL1 rejects the deletion of
      the target Profile, the ISD-R SHALL return the MO-SMS containing the response
      indicating the corresponding failure, and the procedure SHALL end.
(11b) If POL1 allows its deletion, the ISD-R SHALL delete the targeted ISD-P and the
      contained Profile.
(11c) The ISD-R SHALL return the MO-SMS to the SM-SR containing the execution status
      of the “ES5.DELETE” command.
(12)  According to the executed sequence and the eUICC responses, the SM-SR SHALL
   update the EIS to reflect that:
      The Profile having the fall-back attribute has been enabled
      The previously Enabled Profile has been disabled or deleted.

NOTE:POL1 and POL2 MAY have different content. As a consequence, both the eUICC and the SM-SR have to ensure the ISD-P deletion based on their respective Policy.

(13)   The SM-SR SHALL return the response to the “ES4.DisableProfile” function to M2M
   SP, indicating that the Profile has been disabled. In case the Profile has also been deleted
   because of POL1 or POL2, the function execution response SHALL include an execution
   status “Executed-WithWarning” indicating that the Profile has also been deleted.
(14)   Unless Operator1 has set an ONC to not receive those notifications, the SM-SR
   SHALL send the “ES4.HandleProfileDisabledNotification” to Operator1, the owner of the
   Profile that was enabled at the beginning of the procedure. In case the Profile has also
   been deleted because of POL1 or POL2, the function execution response SHALL include
   an execution status “Executed-WithWarning” indicating that the Profile has also been
   deleted. In case Operator1 has no direct connection with the SM-SR (SM-SR SHALL be
   able to detect such a situation based on its own database), the SM-SR SHALL send this
   notification to the SM-DP authorised by                  Operator1 by       calling the
   “ES3.HandleProfileEnabledNotification”. The SM-SR can retrieve the SM-DP identity
   based on the EIS content. Then the SM-DP, on reception of this notification, SHALL
   forward it to Operator1 by calling the “ES2.HandleProfileEnabledNotification”.
(15)    Unless Operator2 has set an ONC to not receive those notifications, the SM-SR
   SHALL send the “ES4.HandleProfileEnabledNotification” to Operator2, the owner of
   Profile with Fall-Back Attribute set that is now enabled. In case Operator2 has no direct
   connection with the SM-SR (SM-SR SHALL be able to detect such situation based on its
   own database), the SM-SR SHALL send this notification to the SM-DP authorised by
   Operator2 by calling the “ES3.HandleProfileEnabledNotification”. The SM-SR can
   retrieve the SM-DP identity based on the EIS content. Then the SM-DP, on reception of
   this    notification, SHALL        forward     it  to    Operator2 by      calling    the
   “ES2.HandleProfileEnabledNotification”.
(16)   The SM-SR SHALL also send the “ES4.HandleProfileEnabledNotification” to a
   M2M SP, if authorised by Operator2 the owner of Profile with Fall-Back Attribute set that
   is now enabled.
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   Operator2, the SM-SR SHALL send this notification to this other Operator by calling the
   “ES4.HandleProfileEnabledNotification”.
   If the M2M SP is another Operator connected through its SM-DP and it is authorised by
   Operator2, the SM-SR SHALL send this notification to the SM-DP associated to this other
   Operator by calling the “ES3.HandleProfileEnabledNotification”.
   Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting
   as the M2M SP, by calling the “ES2.HandleProfileEnabledNotification”.

NOTE:This M2M SP might be the same M2M SP as for Operator1 or any other M2M SP.

NOTE:The MT-SMS and MO-SMS SHALL be secured according to section 2.4.

3.19 Profile and ISD-P Deletion via M2M SP

The Profile and ISD-P deletion procedure between the M2M SP and the SM-SR is used to delete the target ISD-P with its Profile on the eUICC (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.18). The procedure is initiated by the M2M SP, based on prior authorisation of the Operator owning the Profile to be deleted, as defined in section 3.20. The procedure illustrates the usage of SMS as a possible transport protocol between SM-SR and eUICC, but can be also performed using other transport protocols.

The sequence flow in the figure below describes the normal case where the target Profile can successfully be deleted.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF box “eUICC” #FFFFFF participant “ISD-R” as ISDR #FFFFFF endbox

M2MSP->>SR: (1) DeleteProfile(eid, iccid) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>M2MSP: Failed Rnote over SR, ISDR #ADD1B2 (3) Optional: If targeted profile is enabled, then execute function "ES4.DisableProfile" Endrnote SR-->>M2MSP: Failed SR->>ISDR: (4) MT-SMS [ES5.DELETE command]SCP80 Rnote over ISDR #FFFFFF (5) Enforce POL1 Endrnote ||| Rnote over ISDR #FFFFFF (6) Delete ISD-P Endrnote ISDR-->>SR: (7) MO-SMS [ES5.DELETE command response]SCP80 Rnote over SR #FFFFFF (8) Update EIS Endrnote SR-->>M2MSP: (9) Profile deletion result SR->>OP: (10) HandleProfileDeletedNotifi cation(eid, iccid) @enduml

Figure 36: Profile and ISD-P Deletion via M2M SP

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure: (1) To delete the targeted Profile of the Operator the M2M SP SHALL call the “ES4.DeleteProfile” function with its relevant input data. (2) The SM-SR SHALL verify that the M2M SP request is acceptable (the verifications that the SM-SR SHALL perform are described in the section 5.4.7), and in particular checks that the M2M SP has the authorisation to enable the targeted profile, and evaluates POL2 of the target Profile. If any of the conditions to be verified are not satisfied, the SM-SR SHALL return a response indicating the failure, and the procedure SHALL end. (3) The SM-SR SHALL check the state of the target Profile. If the target Profile is enabled and if POL2 of the target Profile allows it to be disabled, then the SM-SR SHALL execute the “ES4.DisableProfile” function to first disable the target Profile (and thus enable the Profile having the Fall-Back Attribute). In case of error, a response indicating the failure is returned to the M2M SP, and the procedure SHALL end.

NOTE:Profile change includes a change of the IMSI that is used to attach to the network. As indicated in 3GPP TS 31.102 [52], such a change requires special caution and should always be accompanied by a REFRESH command to avoid inconsistent information being read by the terminal. So while the targeted ISD-P is marked as enabled in this step, it MAY actually become effective only after the terminal executes the REFRESH command.

(4) The SM-SR SHALL send an MT-SMS containing the “ES5.delete” command with its
   relevant input data (see section 4.1.1.4) to the ISD-R. The SM-SR SHALL request a PoR
   to get the execution status of the “ES5.delete” command.
(5) The ISD-R, SHALL enforce POL1. If POL1 rejects deletion of the target Profile, the ISD-R
   SHALL return directly the MO-SMS containing the response indicating a failure, and the
   procedure SHALL end.
(6) If POL1 allows, the ISD-R SHALL delete the targeted ISD-P and the contained Profile.
(7) The ISD-R SHALL return the MO-SMS containing the execution status of the
   “ES5.DELETE” command to the SM-SR.
(8) In case of successful execution, the SM-SR SHALL update the EIS to reflect the newly
   deleted Profile.
(9) The SM-SR SHALL return the response to the “ES4.DeleteProfile” function to the M2M
   SP, indicating that the Profile has been deleted.
(10)   Unless the Operator has set an ONC to not receive those notifications, the SM-SR
   SHALL send the “ES4.HandleProfileDeletedNotification” to the Operator, the owner of
   the Profile. In case the Operator has no direct connection with the SM-SR (SM-SR SHALL
   be able to detect such a situation based on its own database), the SM-SR SHALL send
   this notification to the SM-DP authorised by the Operator by calling the
   “ES3.HandleProfileDeletedNotification”. The SM-SR can retrieve the SM-DP identity
based on the EIS content. Then the SM-DP, on reception of this notification, SHALL
forward it to the Operator by calling the “ES2.HandleProfileDeletedNotification”.

NOTE:The MT-SMS and MO-SMS SHALL be secured according to section 2.4.

3.20 Profile Lifecycle Management Authorisation (PLMA)

The Profile Lifecycle Management Authorisation (PLMA) mechanisms described in this
section allows the Operator and owner of Profiles to grant authorisations to an M2M SP to
perform certain operations, or receive certain notifications, related to a set of Profiles, identified
by a Profile Type. A list of available operations and notification for the M2M SP can be found
in section 5.1.1.2.14.
The Operator can manage the PLMA for its own Profiles through a dedicated Operator / SM-
SR interface, as described in section 5.7 or through its Operator / SM-DP interface as
described in sections 5.3.13 and 5.3.14.
A “PLMA” is a combination of identifiers and authorised actions:
    -    Identifiers: List of identifiers to identify the Operator, M2M SP and Profile Type; see
         section 5.1.1.2.14 for details

-Authorised actions: List of operations and notifications; see section 5.1.1.2.14 for details

NOTE:It should be considered that the role of a M2M SP can also be played by a partner Operator or affiliate from the Operator, who is responsible to provide Profile Lifecycle Management Authorisations to its own profile(s).

3.20.1 Set Profile Lifecycle Management Authorisation

The Set Profile Lifecycle Management Authorisation (PLMA) procedure between the Operator and the SM-SR is used to authorise the M2M SP for the profile lifecycle management of the Operator owned Profile installed on an eUICC, and to authorise the reception of notifications when the status of the authorised Profile on the eUICC has changed (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.15.1). The PLMA contains the authorised operations and notifications and will be provided as input parameters by the Operator owning the Profile to the SM-SR, see section 5.1.1.2.14.

NOTES:

-    The management of POL2 cannot be authorised to a M2M SP
-    If no PLMA is configured in the SM-SR for a given set of identifiers, then no
     authorisations SHALL be granted to any other function caller apart from the Operat or
     who is owning the targeted Profiles.

The sequence flow in the figure below describes the procedure.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF

OP->>SR: (1) SetPLMA(identifiers, PLMA) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>OP: Failed Rnote over SR #FFFFFF (3) Store PLMA Endrnote SR-->>OP: (4) SetPLMA result SR->>M2MSP: (5) HandlePLMAChangedNotification (identifiers)

@enduml

Figure 37: Set PLMA

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure: (1) To set a PLMA for a M2M SP, an Operator SHALL call the “ES4A.SetPLMA” function with its relevant input parameters, see section 5.7.1, and the list of authorised operations and notifications, see section 5.1.1.2.14. (2) The SM-SR SHALL verify that the Operator request is acceptable (the verifications that the SM-SR SHALL perform are described in the section 5.7.1, and in particular checks that the function caller is the Operator owning the targeted Profile Type. If any of the conditions to be verified are not satisfied, the SM-SR SHALL return a response indicating the failure, and the procedure SHALL end.

(3) The SM-SR creates and stores the PLMA based on the input parameters provided in the function call by the Operator. In case a PLMA already exists for the set of identifiers provided as input parameters, the PLMA is overwritten with new authorisations and the SM-SR SHALL indicate a success but with warning. It SHALL be possible to set a PLMA for a given Profile Type even if this Profile Type is not referenced in an EIS in the SM-SR. In that case, the PLMA referencing this Profile Type SHALL become applicable as soon as the Profile Type reference is added to any EIS and the SM-SR SHALL indicate a success and optionally with warning. (4) The SM-SR SHALL return the response to the “ES4A.SetPLMA” function to the Operator, indicating that the PLMA have been set. (5) The SM-SR SHALL send the “ES4.HandlePLMAChangedNotification” to the M2M SP indicating the identifiers and the applied authorisations of the “ES4A.SetPLMA” function. If the M2M SP is another Operator connected through its SM-DP, the SM-SR SHALL send this notification to the SM-DP associated to this other Operator by calling the “ES3.HandlePLMAChangedNotification”. Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting as the M2M SP, by calling the “ES2.HandlePLMAChangedNotification”

Once the PLMA is set in the SM-SR, the M2M SP is able to call authorised Profile Lifecycle Management functions and to receive authorised notifications on Profile status changes for the Profiles addressed by this PLMA via the SM-SR. When the M2M SP is an Operator, it is also able to call authorised Profile Lifecycle Management functions and to receive authorised notifications on Profile status changes for the Profiles addressed by this PLMA via its SM- DP. The list of authorised operations and notifications can be found in Table 511214-B: List of Operation Eligible to PLMA.

3.20.2 Set Profile Lifecycle Management Authorisation rules via SM-DP

The Set Profile Lifecycle Management Authorisation procedure between the Operator and the SM-SR is done through the SM-DP (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.15.1). The procedure is initiated by the Operator owning the targeted Profile Type and is similar to the procedure “Set Profile Lifecycle Management Authorisation rules” described in section 3.20.1.

The sequence flow in the figure below describes the procedure.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF

OP->>DP: (1) SetPLMA(identifiers, PLMA) DP->>SR: (2) SetPLMA(identifiers, PLMA) Rnote over SR #FFFFF (3) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP: Failed Rnote over SR #FFFFFF (4) Store PLMA Endrnote SR-->>DP: (5) SetPLMA result SR->>M2MSP: (6) HandlePLMAChangedNotification (identifiers) DP-->>OP: (7) SetPLMA result

@enduml

Figure 38: Set PLMA via SM -DP

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure: (1) To set a PLMA for a M2M SP, an Operator SHALL call the “ES2.SetPLMA” function with its relevant input parameters, see section and the list of authorised operations and notifications

(2) The SM-DP SHALL forward the request to the SM-SR identified by the Operator and SHALL call the “ES3.SetPLMA” function with its relevant input data. (3) The SM-SR SHALL verify that the Operator request is acceptable (the verifications that the SM-SR SHALL perform are described in the section 5.4.16), and in particular checks that the function calling SM-DP is belonging to the Operator owning the targeted Profile Type. If any of the conditions to be verified are not satisfied, the SM-SR SHALL return a response indicating the failure, and the procedure SHALL end. (4) The SM-SR creates and stores the PLMA based on the input parameters provided in the function call by the Operator. In case a PLMA already exists for the set of identifiers provided as input parameters, the PLMA is overwritten with new authorisations and the SM-SR SHALL indicate a success but with warning. It SHALL be possible to set a PLMA for a given Profile Type even if this Profile Type is not referenced in an EIS in the SM-SR. In that case, the PLMA referencing this Profile Type SHALL become applicable as soon as the Profile Type reference is added to any EIS and the SM-SR SHALL indicate a success and optionally with warning. (5) The SM-SR SHALL return the response to the “ES3.SetPLMA” function to the SM-DP, indicating that the PLMA have been set. (6) The SM-SR SHALL send the “ES4.HandlePLMAChangedNotification” to the M2M SP indicating the identifiers and the applied authorisations of the “ES2.SetPLMA” function. If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by the Operator owning the Profile, the SM-SR SHALL send this notification to this other Operator by calling the “ES4.HandlePLMAChangedNotification”.

If the M2M SP is another Operator connected through its SM-DP and it is authorised by the Operator owning the Profile, the SM-SR SHALL send this notification to the SM-DP associated to this other Operator by calling the “ES3.HandlePLMAChangedNotification”. Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting as the M2M SP, by calling the “ES2.HandlePLMAChangedNotification”.

(7) Finally, the SM-DP SHALL return the response to the “ES2.SetPLMA” function call to the Operator.

Once the PLMA is set in the SM-SR, the M2M SP is able to call authorised Profile Lifecycle Management functions and to receive authorised notifications on Profile status changes for the Profiles addressed by this PLMA via the SM-SR. When the M2M SP is an Operator, it is also able to call authorised Profile Lifecycle Management functions and to receive authorised notifications on Profile status changes for the Profiles addressed by this PLMA via its SM- DP. The list of authorised operations and notifications can be found in Table 511214-B: List of Operation Eligible to PLMA.

3.20.3 Retrieve Profile Lifecycle Management Authorisation by Operator

The Retrieve PLMA procedure between the Operator and the SM-SR is used to retrieve the list of PLMA granted by the Operator to a M2M SP or the PLMA granted by the Operator for a Profile Type or the PLMA for a dedicated Operator owned single Profile, (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.15.2). The result of the function call provides back the granted PLMA(s) based on the provided input parameters.

The sequence flow in the figure below describes the procedure.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF

OP->>SR: (1) GetPLMA(identifiers) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>OP: Failed Rnote over SR #FFFFFF (3) Retrieve PLMA Endrnote SR-->>OP: (4) GetPLMA result (PLMA) @enduml

Figure 39: Retrieve PLMA by Operator

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:
(1) To retrieve the PLMA(s) an Operator SHALL call the “ES4A.GetPLMA” or the
    “ES4.GetPLMA” function with its relevant input parameters, see section 5.7.2 and 5.5.17.
(2) The SM-SR SHALL verify that the Operator request is acceptable (the verifications that
    the SM-SR SHALL perform are described in the section 5.7.2). If any of the conditions to
    be verified are not satisfied, the SM-SR SHALL return a response indicating the failure,
    and the procedure SHALL end.
    NOTE         If the function caller is an Operator that is not the owner of the targeted
                 Profile or Profile Type, the call may still be valid, but in this case the calling
                 Operator is merely acting as an M2M SP, similar to the procedure described
                 in section 3.20.5. The checks the SM-SR shall perform in this case are
                 described in section 5.5.17.
(3) The SM-SR retrieves the PLMA(s) matching with the identifiers set as input parameters by
    the Operator. In case no PLMA exists for the provided identifier, the SM-SR SHALL return
    an empty result.
(4) The SM-SR SHALL return the response to the “ES4.GetPLMA” function call to the
    Operator.

3.20.4 Retrieve Profile Lifecycle Management Authorisation by Operator via SM-DP

The Retrieve Profile Lifecycle Management Authorisation procedure between the Operator and the SM-SR is done through the SM-DP (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.15.2). The procedure is initiated by the Operator is similar to the procedure “Set Profile Lifecycle Management Authorisation Rules” described in section 3.20.3. The result of the function call provides back the granted PLMA (s) based on the provided input parameters

The sequence flow in the figure below describes the procedure.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF

OP->>DP: (1) GetPLMA(identifiers) DP->>SR: (2) GetPLMA(identifiers) Rnote over SR #FFFFF (3) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP: Failed Rnote over SR #FFFFFF (4) Retrieve PLMA Endrnote SR-->>DP: (5) GetPLMA result (PLMA) DP-->>OP: (6) GetPLMA result (PLMA) @enduml

Figure 40: Retrieve PLMA by Operator via SM -DP

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:
(1) To retrieve the PLMA(s) an Operator SHALL call the “ES2.GetPLMA” function of its SM-
    DP with its relevant input parameters, see section 5.3.14.
(2) The SM-DP SHALL forward the request to the SM-SR identified by the Operator and
    SHALL call the “ES3.GetPLMA” function with its relevant input data.
(3) The SM-SR SHALL verify that the Operator request is acceptable (the verifications that
    the SM-SR SHALL perform are described in the section 5.4.17). If any of the conditions to
    be verified are not satisfied, the SM-SR SHALL return a response indicating the failure,
    and the procedure SHALL end.
    NOTE         If the SM-DP has sent the request on behalf of an Operator that is not the
                 owner of the targeted Profile or Profile Type, the call may still be valid, but in
                 this case this Operator is merely acting as an M2M SP. The checks the SM-
                 SR shall perform are described in section 5.4.17.
(4) The SM-SR retrieves the PLMA(s) matching with the identifiers set as input parameters by
    the Operator. In case no PLMA exists for provided identifier, the SM-SR SHALL return an
    empty result.
(5) The SM-SR SHALL return the response to the “ES3.RetrivePLMA” function to the SM-
    DP.
(6) Finally, the SM-DP SHALL return the response to the “ES2.GetPLMA” function call to the
    Operator.

3.20.5 Retrieve Profile Lifecycle Management Authorisation by M2M SP

The Retrieve PLMA procedure between the M2M SP and the SM-SR is used to retrieve the list of PLMA granted by an Operator to a M2M SP or the PLMA granted by an Operator for a Profile Type or the PLMA for a dedicated Operator owned single Profile (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.15.2). The result of the function call provides back the granted PLMA (s) based on the provided input parameters.

The sequence flow in the figure below describes the procedure.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “M2M SP” as M2MSP #FFFFFF participant “SM-SR” as SR #FFFFFF

M2MSP->>SR: (1) GetPLMA(identifiers) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>M2MSP: Failed Rnote over SR #FFFFFF (3) Retrieve PLMA Endrnote SR-->>M2MSP: (4) GetPLMA result (PLMA) @enduml

Figure 41: Retrieve PLMA by M2M SP

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:
(1) To retrieve the PLMA(s) the M2M SP SHALL call the “ES4.GetPLMA” function with its
    relevant input parameters, see section 5.5.17.
(2) The SM-SR SHALL verify that the M2M SP request is acceptable (the verifications that the
    SM-SR SHALL perform are described in the section 5.5.17. If a Profile Type or a single
    Profile is indicated in the input parameters, the SM-SR SHALL check that the M2M SP is
    authorised for the targeted Profile Type or single Profile. If any of the conditions to be
    verified are not satisfied, the SM-SR SHALL return a response indicating the failure, and
    the procedure SHALL end.
(3) The SM-SR retrieves the PLMA(s) for the requesting M2M SP matching with the identifiers
    set as input parameters by the M2M SP. In case no PLMA(s) exists for the provided
    identifier, the SM-SR SHALL return an empty result.
(4) The SM-SR SHALL return the response to the “ES4.GetPLMA” function call to the M2M
    SP.

3.21 Operator Notifications Configuration (ONC)

The Operator Notifications Configuration (ONC) mechanisms described in this section allows
the Operator and owner of Profiles to define which notifications it would like to receive or not
for a dedicated set of its Profiles, whenever the status of its Profiles has changed; whatever
the origin of the status change is.
The support of this functionality by the SM-SR is optional:
    If the SM-SR supports this functionality, the SM-SR SHALL implement it as specified
      in this section and its subsections, and following the specification of the related
      functions SetONC and GetONC of the off-card interfaces.
    If the SM-SR does not support this functionality, the SM-SR SHALL NOT accept calls
      to setONC, and the SM-SR SHALL send the notifications to the Operator owning a
      Profile as specified in the procedures of sections 3.2 to 3.19, considering that the
      Operator has not set an ONC.
The Operator can manage the Operator Notifications Configuration for its own Profiles through
a dedicated Operator / SM-SR interface, as described in section 5.7.3 and 5.7.4 or through its
Operator / SM-DP interface as described in section 5.3.18 and 5.3.19.
An ONC is a combination of identifiers and discarded notifications:
   -     Identifiers: List of identifiers to identify the Operator and Profile Type; see section
         5.1.1.2.15 for details

-Discarded notifications: List of notifications which SHALL NOT be sent to the Operator; see section 5.1.1.2.15 for details

3.21.1 Set Operator Notifications Configuration

The Set Operator Notification Configuration procedure between the Operator and the SM-SR is used to configure Profile status change notifications received by the Operator for its Profiles; whatever the origin of the status change is. The procedure provides to the SM-SR a Profile Type and a list of notifications to indicate which notifications SHALL be send to the Operator in case of any Profile status change of the targeted Profile Type.

NOTE:If no Operator Notification Configuration has yet been set in the SM-SR for a given Profile Type, then the Operator will receive all notifications for status changes for its own Profiles, associated with this Profile Type.

The sequence flow in the figure below describes the procedure.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF

OP->>SR: (1) SetONC (identifiers, notifications list) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>OP: Failed Rnote over SR #FFFFFF (3) Store Operator Notification Configuration Endrnote SR-->>OP: (4) SetONC result @enduml

Figure 3211-A: Set Operator Notification Configuration

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:
(1) To set its own Operator Notification Configuration, an Operator SHALL call the
    “ES4A.SetONC” function with its relevant input parameters, in particular the targeted
    Profile Type and the list of notifications, see in detail section 5.7.3.
(2) The SM-SR SHALL verify that the Operator request is acceptable (the verifications that
    the SM-SR SHALL perform are described in the section 5.7.3). If any of the conditions to
    be verified are not satisfied, the SM-SR SHALL return a response indicating the failure,
    and the procedure SHALL end.
(3) The SM-SR creates and store the Operator Notification Configurations based on the input
    parameters provided in the function call by the Operator. In case a configuration already
    exists for the Operator and the targeted Profile Type, the configuration is overwritten with
   the new configuration provided as input parameters and the SM-SR SHALL indicate a
   success but with warning.
   It SHALL be possible to set the Operator Notification Configurations for a given Profile
   Type even if this Profile Type is not referenced in an EIS in the SM-SR. In that case, the
   Operator Notification Configuration referencing this Profile Type SHALL become
   applicable as soon as the Profile Type reference is added to any EIS and the SM-SR
   SHALL indicate a success and optionally with warning.
(4) The SM-SR SHALL return the response to the “ES4A.SetONC” function to the Operator,
    indicating that the Notification Configuration has been set.

3.21.2 Set Operator Notifications Configuration via SM-DP

The Set Operator Notification Configuration procedure between the Operator and the SM-SR is done through the SM-DP (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.15.1). The procedure is initiated by the Operator owning t he targeted Profile Type and is similar to the procedure “Set Operator Notification Configuration” described in section 3.21.1.

The sequence flow in the figure below describes the procedure.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF

OP->>DP: (1) SetONC (identifiers, notifications list) DP->>SR: (2) SetONC(identifiers, notifications list) Rnote over SR #FFFFF (3) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP: Failed Rnote over SR #FFFFFF (4) Store Operator Notification Configuration Endrnote SR-->>DP: (5) SetONC result DP-->>OP: (6) SetONC result @enduml

Figure 42: Set Operator Notification Configuration via SM-DP

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:
(1) To set its own Operator Notification Configuration, an Operator SHALL call the
    “ES2.SetONC” function of its SM-DP with its relevant input parameters, in particular the
    targeted Profile Type and the list of notifications, see in detail section 5.3.18.
(2) The SM-DP SHALL forward the request to the SM-SR identified by the Operator and
    SHALL call the “ES3.SetONC” function with its relevant input data.
(3) The SM-SR SHALL verify that the Operator request is acceptable (the verifications that
    the SM-SR SHALL perform are described in the section 5.3.18). If any of the conditions to
    be verified are not satisfied, the SM-SR SHALL return a response indicating the failure,
    and the procedure SHALL end.
(4) The SM-SR creates and store the Operator Notification Configurations based on the input
    parameters provided in the function call by the Operator. In case a configuration already
    exists for the Operator and the targeted Profile Type, the configuration is overwritten with
    the new configuration provided as input parameters and the SM-SR SHALL indicate a
    success but with warning.
   It SHALL be possible to set the Operator Notification Configurations for a given
   Profile Type even if this Profile Type is not referenced in an EIS in the SM-SR. In
   that case, the Operator Notification Configuration referencing this Profile Type
   SHALL become applicable as soon as the Profile Type reference is added to any
   EIS and the SM-SR SHALL indicate a success and optionally with warning.
(5) The SM-SR SHALL return the response to the “ES3.SetONC” function to the SM-DP,
    indicating that the Notification Configuration has been set.
(6) Finally, the SM-DP SHALL return the response to the “ES2.SetONC” function call to the
    Operator.

3.21.3 Retrieve Operator Notifications Configuration

The Retrieve Operator Notification Configuration procedure between the Operator and the SM-SR is used to retrieve the list of notifications an Operator would like not to receive for a dedicated Operator owned Profile Type (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.15). The result of the function call provides back the discarded notifications based on the provided input parameters.

NOTE:If no Operator Notification Configuration has yet been set in the SM-SR for a given Profile Type, then the output data of this function will return an empty result, as all notifications will be sent for Profiles assigned with this Profile Type, see also section 5.7.4 for details.

The sequence flow in the figure below describes the procedure.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF

OP->>SR: (1) GetONC (identifiers, notifications list) Rnote over SR #FFFFF (2) Check initial conditions Endrnote SR-->>OP: Failed Rnote over SR #FFFFFF (3) Retrieve Operator Notification Configuration Endrnote SR-->>OP: (4) GetONC result @enduml

Figure 43: Retrieve Operator Notification Configuration

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:

(1) To retrieve the Operator Notifications Configuration list, an Operator SHALL call the
    “ES4A.GetONC” function with its relevant input parameters, see section 5.7.4.
(2) The SM-SR SHALL verify that the Operator request is acceptable (the verifications that
    the SM-SR SHALL perform are described in the section 5.7.4), and in particular checks
    that the function caller is the Operator owning the targeted Profile Type. If any of the
    conditions to be verified are not satisfied, the SM-SR SHALL return a response indicating
    the failure, and the procedure SHALL end.
(3) The SM-SR retrieves the list of Operator Notifications Configuration matching with the
    identifiers set as input parameters by the Operator. In case no ONC exists for the provided
    identifier, the SM-SR SHALL return an empty result.
(4) The SM-SR SHALL return the response to the “ES4.GetONC” function call to the
    Operator, indicating the list of notifications for the targeted profile.

3.21.4 Retrieve Operator Notifications Configuration via SM-DP

The Retrieve Operator Notification Configuration procedure between the Operator and the SM-SR is done through the SM-DP (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.15.1). The procedure is initiated by the Operator owning the targeted Profile Type and is similar to the procedure “Retrieve Operator Notification Configuration” described in section 3.21.1. The result of the function call provides back the discarded notifications based on the provided input parameters.

NOTE:If no Operator Notification Configuration has yet been set in the SM-SR for a given Profile Type, then the output data of this function will return an empty result, as all notifications will be sent for Profiles assigned with this Profile Type, see also section 5.7.4 for details.

The sequence flow in the figure below describes the procedure.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox

participant “Operator” as OP #FFFFFF participant “SM-DP” as DP #FFFFFF participant “SM-SR” as SR #FFFFFF

OP->>DP: (1) GetONC (identifiers, notifications list) DP->>SR: (2) GetONC (identifiers, notifications list) Rnote over SR #FFFFF (3) Check initial conditions Endrnote SR-->>DP: Failed DP-->>OP: Failed Rnote over SR #FFFFFF (4) Retrieve Operator Notification Configuration Endrnote SR-->>DP: (5) GetONC result DP-->>OP: (6) GetONC result @enduml

Figure 44: Retrieve Operator Notification Configuration via SM-DP

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:

(1) To retrieve the Operator Notifications Configuration list, an Operator SHALL call the
    “ES2.GetONC” function of its SM-DP with its relevant input parameters, see section
    5.3.19.
(2) The SM-DP SHALL forward the request to the SM-SR identified by the Operator and
    SHALL call the “ES3.GetONC” function with its relevant input data.
(3) The SM-SR SHALL verify that the Operator request is acceptable (the verifications that
    the SM-SR SHALL perform are described in the section 5.4.22), and in particular checks
    that the function calling SM-DP is belonging to the Operator owning the targeted Profile
    Type. If any of the conditions to be verified are not satisfied, the SM-SR SHALL return a
    response indicating the failure, and the procedure SHALL end.
(4) The SM-SR retrieves Operator Notifications Configuration list matching with the identifiers
    set as input parameters by the Operator. In case no ONC exists for the provided identifier,
    the SM-SR SHALL return an empty result.
(5) The SM-SR SHALL return the response to the “ES3.GetONC” function to the SM-DP,
    indicating the list of notifications for the targeted profile.
(6) Finally, the SM-DP SHALL return the response to the “ES2.GetONC” function call to the
    Operator.

3.22 Local Enable for Test Profile

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 120 skinparam sequenceArrowThickness 1

hide footbox

participant “Device” as DEV #FFFFFF participant “eUICC” as eUICC #FFFFFF

DEV->>eUICC : (1) ESx.LocalEnableTestProfile
Rnote over eUICC #FFFFF
(2) Verify that the Test Profile exists
Endrnote
eUICC-->>DEV : Error
Rnote over eUICC #FFFFF
(3) Verify that the currently Enabled Profile
     is NOT the Emergency Profile
Endrnote
eUICC-->>DEV : Error
Rnote over eUICC #FFFFF
 (4) Verify that the currently Enabled Profile
     is NOT the Test Profile
Endrnote
eUICC-->>DEV : Error

Group Profile switch Rnote over eUICC #FFFFF (5) Enable Test Profile Endrnote eUICC-->>DEV : (6) Success ||| eUICC-->>DEV: (7) REFRESH, (UICC reset) ||| Rnote over DEV, eUICC #FFFFFF (8) Network attachment with the Enabled Profile Endrnote end @enduml

Figure 322: Local Enable of Test Profile

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:
(1) The Device SHALL call the “ESx.LocalEnableTestProfile” function.
(2) The eUICC SHALL verify that the Test Profile exists (including Flag and NAA keys as
    described in EUICC23 in SGP.01 [1]). If any of the conditions to be verified are not
    satisfied, the eUICC SHALL return a response indicating the failure, and the procedure
    SHALL end.
(3) The eUICC SHALL verify that the current enabled Profile is NOT the Emergency Profile.
    If the condition to be verified is not satisfied, the eUICC SHALL return a response indicating
    the failure, and the procedure SHALL end.
(4) The eUICC SHALL verify that the currently enabled Profile is NOT the Test Profile. If the
    condition to be verified is not satisfied, the eUICC SHALL return a response indicating that
    the Test Profile is already Enabled, and the procedure SHALL end.
(5) The eUICC SHALL NOT enforce POL1 of the currently Enabled Profile, and SHALL
    disable the currently enabled Profile, and enable the Test Profile.
   NOTE:        Profile change includes a change of the IMSI that is used to attach to the
                network. As indicated in 3GPP TS 31.102 [52], such a change requires special
                caution and should always be accompanied by a REFRESH command to
                avoid inconsistent information being read by the terminal. So while the Profile
                is marked as enabled in this step, it MAY actually become effective after the
                terminal executes the REFRESH command.
(6) The eUICC SHALL return the execution status of the “ ESx. LocalEnableTestProfile”
    command to the Device.
(7) The eUICC SHALL send a REFRESH proactive command in UICC reset mode to the
    Device. This will trigger the execution of a network attach procedure.
(8) The Device SHALL perform a network attach procedure with the newly enabled Profile.

NOTE:Whether the Test Profile provides connectivity to a test network or not, the eUICC will not attempt to enable automatically the previously Enabled Profile. This is in contrast to the remote enable procedures (for example in section 3.2.2).

3.23 Local Disable for Test Profile

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 100 skinparam sequenceArrowThickness 1

hide footbox

participant “Device” as DEV #FFFFFF participant “eUICC” as ISDR #FFFFFF

DEV->>ISDR : (1) ESx.LocalDisableTestProfile
Rnote over ISDR #FFFFF
(2) Verify that the currently Enabled Profile
     is the Test Profile
Endrnote
ISDR-->>DEV : Error
group Profile switch
Rnote over ISDR #FFFFF
(3) Disable Test Profile and
      enable previously Enabled Profile
Endrnote
ISDR-->>DEV : (4) Success
|||
ISDR-->>DEV: (5) REFRESH, (UICC reset)
|||
Rnote over DEV, ISDR #FFFFFF
(6) Network attachment with the Enabled Profile
Endrnote
End
@enduml

Figure 323: Local Disable of Test Profile

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:
(1) The Device SHALL call the “ESx.LocalDisableTestProfile” function.
(2) The eUICC SHALL verify that the currently Enabled Profile is the Test Profile (including
    Flag and NAA keys as described in EUICC23 in SGP.01[1]). If any of the conditions to be
    verified are not satisfied, the eUICC SHALL return a response indicating that the currently
    Enabled Profile is not the Test Profile, and the procedure SHALL end.
(3) The eUICC SHALL disable the Test Profile and enable the previously enabled Profile.
(4) The eUICC SHALL return the execution status of the “ ESx.LocalDisableTestProfile”
    command to the Device.
(5) The eUICC SHALL send a REFRESH proactive command in UICC reset mode to the
    Device. This will trigger the execution of a network attach procedure.

NOTE:In case of any error after this step, indicating that the currently Enabled Profile cannot provide connectivity, the eUICC will trigger the Fall-Back Mechanism and will ensure that the previously enabled Profile is the Profile that was enabled before the Local Enable.

(6) The eUICC and the Device SHALL perform a network attach procedure with the newly
    Enabled Profile.

Dependent on the configuration of the eUICC, the eUICC MAY send a Notification about the Profile change after Test Profile disabling to the SM-SR.

3.24 POL2 Update

This procedure is used by the Operator to update POL2 via the SM-SR.

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 400 skinparam ParticipantPadding 50 skinparam sequenceArrowThickness 1

hide footbox participant “M2M SP” as M2MSP #FFFFFF participant “Operator” as OP #FFFFFF participant “SM-SR” as SR #FFFFFF

OP->>SR: (1) UpdatePolicyRules(POL2) Rnote over SR #FFFFF (2) Update POL2 Endrnote SR-->>OP: (3) UpdatePolicyRules Result SR->>M2MSP: (4) Cond: HandleProfilePOL2UpdatedNotification (eid, iccid, POL2) @enduml

Figure 324: POL2 Update

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:
(1) The Operator owner of the target Profile SHALL call the “ ES4.UpdatePolicyRules”
    function with its relevant input data, as described in section 5.3.3.
(2) The SM-SR SHALL update the POL2 of the targeted eUICC’s EIS.
(3) The SM-SR SHALL return the execution status of the “ES4.UpdatePolicyRules” to the
    Operator.
(4) The SM-SR SHALL send the “ES4.HandleProfilePOL2UpdatedNotification” to a M2M
    SP, if authorised by the Operator owning the Profile, indicating the updated POL2 rules
    according to chapter 5.1.1.2.2.
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   the Operator owning the Profile, the SM-SR SHALL send this notification to this other
   Operator by calling the “ES4.HandleProfilePOL2UpdatedNotification”.
   If the M2M SP is another Operator connected through its SM-DP and it is authorised by
   the Operator owning the Profile, the SM-SR SHALL send this notification to the SM-DP
associated     to        this      other         Operator      by         calling       the
“ES3.HandleProfilePOL2UpdatedNotification”.
Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting
as the M2M SP, by calling the “ES2.HandleProfilePOL2UpdatedNotification”

3.25 Emergency Profile Attribute Management

This procedure specifies setting the Emergency Profile Attribute for a Profile when no other Profile has the Emergency Profile Attribute set (case 1), or, a change regarding the Profile that has the Emergency Profile Attribute set (case 2). For case 2, the Operator1 owning the Profile that currently has the Emergency Profile Attribute set and the Operator2 that wants to set the Emergency Profile Attribute on its own Profile SHALL have an agreement. This agreement is materialized by the Operator1 setting a PLMA where it MAY grant Operator2 the authorisation to unset the Emergency Profile Attribute on this Operator1 Profile. NOTE There is no operation that explicitly unsets the Emergency Profile Attribute on a Profile. The Emergency Profile Attribute is only unset as a consequence of setting the Emergency Profile Attribute on another Profile.

For case 1 the procedure below applies:

@startuml skinparam monochrome true skinparam ArrowColor Black

hide footbox

Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-DP” as DP #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF

Alt [via SM-SR] OP2->SR: [1.a] ES4.SetEmergencyProfileAttribute(EID,ICCID)\non Profile B Request

Else [via SM-DP] OP2->DP: [1.b] ES2.SetEmergencyProfileAttribute(EID,SMSR -ID,ICCID)\non Profile B Request

Rnote over DP #FFFFFF Identify SM-SR Endrnote

DP<->SR: Mutual Authentication

DP->SR: [1.c] ES3.SetEmergencyProfileAttribute(EID,ICCID) \non Profile B Request

end

SR->EUICC: [2] ES5.SetEmergencyProfileAttribute(ISD -P AID)\non Profile B

Rnote over EUICC #FFFFFF [3a] Verify if Profile B has not set Fall -Back Attribute Endrnote EUICC-->SR: [3.a] Send STORE DATA response indicating an error

Rnote over EUICC #FFFFFF [3b] Set Emergency Profile Attribute on Profile B Endrnote

EUICC->SR: [4] SetEmergencyProfileAttribute response

Rnote over SR #FFFFFF [5] EIS Update(AdditionalProperty) Endrnote

Alt [via SM-SR] SR->OP2: 6.a] ES4.HandleEmergencyProfileAttributeSetNotification \non Profile B Request SR->OP1

Else [via SM-DP]

SR->DP: [6.b] ES3.SetEmergencyProfileAttribute(EID,ICCID) \non Profile B Request

DP->OP2: [6.c] ES2.HandleEmergencyProfileAttributeSetNotification\non Profile B Request

end

Opt [If if requested by Operator 2] SR->SP: [7] HandleEmergencyProfileAttributeSetNotification of Profile B end @enduml

Figure 325-A: Emergency Profile Attribute Management (case 1: first Emergency

Profile)
Start Conditions (case 1):
   a. No Profile with Emergency Profile Attribute set exists.
   b. Profile B, targeted to have the Emergency Profile Attribute set is present on the eUICC
       and disabled
   c. Profile B does not have the Fall-Back Attribute set.
Procedure (case 1):
(1) The Operator2 owning Profile B requests setting of the Emergency Profile Attribute on
    Profile    B    to   the    SM-SR,       either  directly (1.a)   by    calling    the
    “ES4.SetEmergencyProfileAttribute” function with the relevant input parameters or
    through its SM-DP (1.b) by calling the “ES2.SetEmergencyProfileAttribute” function with
    the relevant input parameters and the SM-DP forwarding the request to the SM-SR (1c)
    by calling the “ES3.SetEmergencyProfileAttribute” function with the relevant input
    parameters.
(2) The SM-SR, by calling the “ES5.SetEmergencyProfileAttribute” function, requests the
    eUICC to set the Emergency Profile Attribute to the Profile B.
(3) The eUICC SHALL verify that Profile B does not have the Fall-Back Attribute set (3a) and
    SHALL then set the Emergency Profile Attribute to Profile B (3b).
          a. If the conditions (3a) is not true, the eUICC SHALL abort the procedure and
             SHALL send an error response to the SM-SR as detailed in the
             “ES5.SetEmergencyProfileAttribute” function.
(4) The eUICC SHALL send the “ES5.SetEmergencyProfileAttribute” response to the SM-
    SR
(5) The SM-SR SHALL update the EIS accordingly by adding the information that the
    Emergency Profile has been set on Profile B in the AdditionalProperty field.
(6) Based on ONC, the SM-SR SHALL notify to all Operators, having a Profile on this eUICC,
    either          directly       (6a)             by             calling             the
   “ES4.HandleEmergencyProfileAttributeSetNotification”, or via the SM-DP (6b) by
   calling the “ES3.HandleEmergencyProfileAttributeSetNotification” and the SM-DP
   SHALL        forward       the       notification     (6c)       by        calling the
   “ES2.HandleEmergencyProfileAttributeSetNotification”, that a Profile now has the
   Emergency Profile Attribute set. This notification MAY include the Profile ID.
(7) The    SM-SR       SHALL        notify    the      M2M     SP      by     calling    the
    “ES4.HandleEmergencyProfileAttributeSetNotification”, that the Profile B has the
    Emergency Profile Attribute set, if requested by the Operator2 during Platform Lifecycle
    Management Authorisation registrations (see section 3.20).
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   Operator2, the SM-SR SHALL send this notification to this other Operator by calling the
   “ES4.HandleEmergencyProfileAttributeSetNotification”.

If the M2M SP is another Operator connected through its SM-DP and it is authorised by Operator2, the SM-SR SHALL send this notification to the SM-DP associated to this other Operator by calling the “ES3.HandleEmergencyProfileAttributeSetNotification”. Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting as the M2M SP, by calling the “ES2.HandleEmergencyProfileAttributeSetNotification”. End Conditions (case 1): The Profile B has the Emergency Profile Attribute set. For case 2 the procedure below applies

@startuml skinparam monochrome true skinparam ArrowColor Black

hide footbox

Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-DP” as DP #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF

Alt [via SM-SR] OP2->SR: [1.a] ES4.SetEmergencyProfileAttribute(EID,ICCID)\non Profile B Request

Else [via SM-DP] OP2->DP: [1.b] ES2.SetEmergencyProfileAttribute(EID,SMSR -ID,ICCID)\non Profile B Request

Rnote over DP #FFFFFF Identify SM-SR Endrnote

DP<->SR: Mutual Authentication

DP->SR: [1.c] ES3.SetEmergencyProfileAttribute(EID,ICCID) \non Profile B Request

end

Rnote over SR #FFFFFF [2] Check PLMA for SetmergencyProfileAttribute for Operator 2 Endrnote

SR-->OP2: [2.a] Send error response with authorisation conflict SR->EUICC: [3] ES5.SetEmergencyProfileAttribute(ISD -P AID)\non Profile B

Rnote over EUICC #FFFFFF [4a] Verify if Profile B has not set Fall -Back Attribute Endrnote EUICC-->SR: [4.a] send STORE DATA error response

Rnote over EUICC #FFFFFF [4b] Unset Emergency Profile Attribute on Profile A by Setting Emergency Profile Attribute on Profile B Endrnote

EUICC->SR: [5] SetEmergencyProfileAttribute response

Rnote over SR #FFFFFF [6] EIS Update(AdditionalProperty) Endrnote

SR->OP1: [7] ES4.HandleEmergencyProfileAttributeU nsetNotification\non Profile A

Alt [via SM-SR] SR->OP2: [8.a] ES4.HandleEmergencyProfileAttributeSetNotification \non Profile B SR->OP1

Else [via SM-DP]

SR->DP: [8.b] ES3.HandleEmergencyProfileAttributeSetNotification \non Profile B

DP->OP2: [8.c] ES2.HandleEmergencyProfileAttributeSetNotification \non Profile B

end

Opt [If if requested by Operator 1] SR->SP: [9] HandleEmergencyProfileAttributeUnsetNotification of Profile A End

Opt [If if requested by Operator 2] SR->SP: [10] HandleEmergencyProfileAttributeSetNotification of Profile B end @enduml

Figure 325-B: Emergency Profile Attribute Management (case 2: change of Emergency

Profile)
Start Conditions (case 2):
   a. Profile A with Emergency Profile Attribute set.
   b. Profile B, targeted to have the Emergency Profile Attribute set, present on the eUICC.
   c. Profile A owner Operator1 has configured a PLMA authorising Operator2 to unset the
       Emergency Profile Attribute on Profile A.
Procedure (case 2):
(1) The Operator2 owning Profile B requests setting of the Emergency Profile Attribute on
    Profile    B    to   the    SM-SR,       either  directly (1.a)   by    calling    the
    “ES4.SetEmergencyProfileAttribute” function with the relevant input parameters or
    through its SM-DP (1.b) by calling the “ES2.SetEmergencyProfileAttribute” function with
    the relevant input parameters and the SM-DP forwarding the request to the SM-SR (1c)
    by calling the “ES3.SetEmergencyProfileAttribute” function with the relevant input
    parameters.
(2) The SM-SR checks if Operator2 has PLMA configured to unset the Emergency Profile
    Attribute from the Operator1 owning the Profile that currently has the Emergency Profile
    Attribute set.
           a. If there is a conflict with the authorisation, the SM-SR aborts the procedure and
              informs the Operator 2.
(3) The SM-SR, by calling the “ES5.SetEmergencyProfileAttribute” function, requests the
    eUICC to set the Emergency Profile Attribute to the Profile B.
(4) The eUICC verifies that Profile B does not have the Fall-Back Attribute set (4a) and
    performs the operation (4b). This will remove the Emergency profile Attribute from Profile
    A.
           b. If the conditions (4a) is not true, the eUICC aborts the procedure and return an
               error to the SM-SR as detailed in the “ES5.SetEmergencyProfileAttribute”
               function.
(5) The eUICC SHALL send the “ES5.SetEmergencyProfileAttribute” response to the SM-
    SR.
(6) The SM-SR updates the EIS accordingly by adding the information that the Emergency
    Profile has been set on Profile B in the AdditionalProperty field.
(7) Based on ONC, the SM-SR notifies Operator1, whose Profile has the Emergency Profile
    Attribute               Unset,           by                calling              the
    "ES4.HandleEmergencyProfileAttributeUnsetNotification" that its Profile now has the
    Emergency Profile Attribute unset.
(8) Based on ONC, the SM-SR notifies all Operators, having a Profile on this eUICC either
    directly (8a) by calling the “ES4.HandleEmergencyProfileAttributeSetNotification”, or
    via           the           SM-DP            (8b)         by          calling     the
    “ES3.HandleEmergencyProfileAttributeSetNotification” and the SM-DP SHALL
    forward           the         notification       (8c)        by         calling   the
    “ES2.HandleEmergencyProfileAttributeSetNotification”, that a Profile now has the
    Emergency Profile Attribute set. This notification MAY include the Profile ID.
(9) The SM-SR SHALL notify the M2M SP that the Profile A has the Emergency Profile
    Attribute              unset               by               calling                 the
    “ES4.HandleEmergencyProfileAttributeUnsetNotification”, if requested by the
    Operator1 during Platform Lifecycle Management Authorisation registrations (see 3.5.xx).
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   Operator1, the SM-SR SHALL send this notification to this other Operator by calling the
   “ES4. HandleEmergencyProfileAttributeUnsetNotification”.
   If the M2M SP is another Operator connected through its SM-DP and it is authorised by
   Operator1, the SM-SR SHALL send this notification to the SM-DP associated to this
   other Operator by calling the “ES3.
   HandleEmergencyProfileAttributeUnsetNotification”. Then the SM-DP, on reception
   of this notification, SHALL forward it to the Operator, acting as th e M2M SP, by calling
   the “ES2. HandleEmergencyProfileAttributeUnsetNotification”.
(10) The SM-SR SHALL notify the M2M SP that the Profile B has the Emergency Profile
    Attribute set by calling the “ES4.HandleEmergencyProfileAttributeSetNotification”, if
    requested by the Operator2 during Platform Lifecycle Management Authorisation
    registrations (see 3.5.xx).
    If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
    Operator2, the SM-SR SHALL send this notification to this other Operator by calling the
    “ES4.HandleEmergencyProfileAttributeSetNotification”.

If the M2M SP is another Operator connected through its SM-DP and it is authorised by Operator2, the SM-SR SHALL send this notification to the SM-DP associated to this other Operator by calling the “ES3.HandleEmergencyProfileAttributeSetNotification”. Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting as the M2M SP, by calling the “ES2.HandleEmergencyProfileAttributeSetNotification”. End Conditions (case 2): The Profile A has the Emergency Profile Attribute unset. The Profile B has the Emergency Profile Attribute set.

3.26 Emergency Profile Attribute Management via the M2M SP

Operators may also authorise an M2M SP to change which Profile has the Emergency Profile Attribute set. This procedure specifies setting the Emergency Profile Attribute for a Profile when no other Profile has the Emergency Profile Attribute set (case 1), or, a change regarding the Profile that has the Emergency Profile Attribute set (case 2). For case 1 the Operator2 that agrees to have the Emergency Profile Attribute set on its own Profile need to have an agreement with the M2M SP. This agreement is materialized by the Operator2 setting PLMAs where Operator2 MAY grant the M2M SP the authorisation to set the Emergency Profile Attribute on its respective Profile. For case 2. the Operator1 owning the Profile that currently has the Emergency Profile Attribute set and the Operator2 that agree to have the Emergency Profile Attribute set on its own Profile need to have an agreement with the M2M SP. This agreement is materialized by the Operator2 and Operator1 setting PLMAs where Operator2 MAY grant the M2M SP the authorisation to set the Emergency Profile Attribute on its respective Profile and where Operator1 MAY grant the M2M SP the authorisation to un-set the Emergency Profile Attribute on its respective Profile

NOTE        There is no operation that explicitly unsets the Emergency Profile Attribute on
            a Profile. The Emergency Profile Attribute is only unset as a consequence of
            setting the Emergency Profile Attribute on another Profile.

For case 1 the procedure below applies:

startuml skinparam monochrome true skinparam ArrowColor Black

hide footbox

Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF

SP->SR: [1] ES4.SetEmergencyProfileAttribute(EID,ICCID) \non Profile B Request

Rnote over SR #FFFFFF [2] Check PLMA for Setting Emergency Profile Attribute from Operator 2 Endrnote SR-->SP: [2.a] Send response indicating authorisation conflict

SR->EUICC: [3] ES5.SetEmergencyProfileAttribute(ISD -P AID)\non Profile B

Rnote over EUICC #FFFFFF [4a] Verify if Profile B has not set Fall -Back Attribute Endrnote EUICC-->SR: [4.a] send STORE DATA response with herror

Rnote over EUICC #FFFFFF [4b] Set Emergency Profile Attribute on Profile B Endrnote

EUICC->SR: [5] SetEmergencyProfileAttribute response

Rnote over SR #FFFFFF [6] EIS Update(AdditionalProperty) Endrnote

SR->OP2: [7] ES4.HandleEmergencyProfileAttribute SetNotification of Profile B

SR->OP1

SR->SP: [8] ES4.HandleEmergencyProfileAttributeSetNotification of Profile B @enduml

Figure 326-A: Emergency Profile Attribute Management by M2M SP (case 1: first

Emergency Profile)
Start Conditions:
   a. Profile B, targeted to have the Emergency Profile Attribute set, present on the eUICC.
   b. Profile B owner Operator2 has configured a PLMA authorising the M2M SP to set the
      Emergency Profile Attribute.
Procedure:
(1) The M2M SP requests setting of the Emergency Profile Attribute on Profile B to the SM-
    SR by calling the “ES4.SetEmergencyProfileAttribute” function with the relevant input
    parameters.
(2) The SM-SR checks if a PLMA from Operator2 that authorises the M2M SP to set the
    Emergency Profile Attribute on Profile B is configured
          a. If there is a conflict with the authorisation, the SM-SR aborts the procedure and
             informs the M2M SP.
(3) The SM-SR, by calling the “ES5.SetEmergencyProfileAttribute” function, requests the
    eUICC to set the Emergency Profile Attribute to the Profile B.
(4) The eUICC verifies that Profile B does not have the Fall-Back Attribute set (4a) and then
    sets the Emergency Profile Attribute to the Profile B (4b).
            b. If the conditions (4a) is not true, the eUICC aborts the procedure and sends an
               error to the SM-SR as detailed in the “ES5.SetEmergencyProfileAttribute”
               function.
(5) The eUICC SHALL send the “ES5.SetEmergencyProfileAttribute” response to the SM-
    SR.
(6) The SM-SR updates the EIS accordingly by adding the information that the Emergency
    Profile has been set on Profile B in the AdditionalProperty field.
(7) Based on ONC, the SM-SR notify all Operators, having a Profile on this eUICC, by calling
    the “ES4.HandleEmergencyProfileAttributeSetNotification” that a Profile now has the
    Emergency Profile Attribute set. This notification MAY include the Profile ID.
(8) The        SM-SR         notifies   the M2M       SP      by    calling    the
    “ES4.HandleEmergencyProfileAttributeSetNotification” that the Emergency Profile
    Attribute is now set for Profile B.
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   Operator, the SM-SR SHALL send this notification to this other Operator by calling the
   “ES4.HandleEmergencyProfileAttributeSetNotification”.

If the M2M SP is another Operator connected through its SM-DP and it is authorised by Operator, the SM-SR SHALL send this notification to the SM-DP associated to this other Operator by calling the “ES3.HandleEmergencyProfileAttributeSetNotification”. Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, act ing as the M2M SP, by calling the “ES2.HandleEmergencyProfileAttributeSetNotification” End Conditions: The Profile B has the Emergency Profile Attribute set. For case 2 the procedure below applies:

@startuml skinparam monochrome true skinparam ArrowColor Black

hide footbox

Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-DP” as DP #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF

SP->SR: [1] ES4.SetEmergencyProfileAttribute(EID,ICCID) \non Profile B Request

Rnote over SR #FFFFFF [2] Check PLMA for Setting Emergency Profile Attribute from Operator 2 Endrnote SR-->SP: [2.a] Send response indicating authorisation conflict Rnote over SR #FFFFFF [3] Check PLMA for Unsetting Emergency Profile Attribute from Operator 1 Endrnote SR-->SP: [3.a] Send response indicating authorisation conflict

SR->EUICC: [4] ES5.SetEmergencyProfileAttribute(ISD -P AID)\non Profile B

Rnote over EUICC #FFFFFF [5a] Verify if Profile B has not set Fall -Back Attribute Endrnote EUICC-->SR: [5.a] send error response

Rnote over EUICC #FFFFFF [5b] Unset Emergency Profile Attribute on Profile A by Setting Emergency Profile Attribute on Profile B Endrnote

EUICC->SR: [6] SetEmergencyProfileAttribute response

Rnote over SR #FFFFFF [7] EIS Update(AdditionalProperty) Endrnote

SR->OP1: [8] ES4.HandleEmergencyProfileAttribute UnsetNotification\non Profile A

Alt [via SM-SR] SR->OP2: [9.a] ES4.HandleEmergencyProfileAttributeSetNotification \non Profile B SR->OP1

Else [via SM-DP]

SR->DP: [9.b] ES3.HandleEmergencyProfileAttributeSetNotification \non Profile B

DP->OP2: [9.c] ES2.HandleEmergencyProfileAttributeSetNotification \non Profile B

end

Opt [If if requested by Operator 1] SR->SP: [10] HandleEmergencyProfileAttributeUnsetNotification of Profile A End

Opt [If if requested by Operator 2] SR->SP: [11] HandleEmergencyProfileAttributeSetNotification of Profile B end

@enduml

Figure 326-B: Emergency Profile Attribute Management by M2M SP (case 2: change of

Emergency Profile)
Start Conditions:
   a. Profile A with Emergency Profile Attribute set.
   b. Profile B, targeted to have the Emergency Profile Attribute set, present on the eUICC.
   c. Profile A owner Operator1 has configured a PLMA authorising the M2M SP to unset
       the Emergency Profile Attribute.
   d. Profile B owner Operator2 has configured a PLMA authorising the M2M SP to set the
       Emergency Profile Attribute.
Procedure:
(1) The M2M SP requests setting of the Emergency Profile Attribute on Profile B to the SM-
    SR by calling the “ES4.SetEmergencyProfileAttribute” function with the relevant input
    parameters.
(2) The SM-SR checks if a PLMA from Operator2 that authorises the M2M SP to set the
    Emergency Profile Attribute on Profile B is configured.
           a. If there is a conflict with the authorisation, the SM-SR aborts the procedure and
              informs the M2M SP.
(3) The SM-SR checks if a PLMA from Operator1 that authorises the M2M SP to unset the
    Emergency Profile Attribute on Profile A is configured.
           b. If there is a conflict with the authorisation, the SM-SR aborts the procedure and
              informs the M2M SP.
(4) The SM-SR, by calling the “ES5.SetEmergencyProfileAttribute” function, requests the
    eUICC to set the Emergency Profile Attribute to the Profile B.
(5) The eUICC verifies that Profile B does not have the Fall-Back Attribute set (5a) and then
    sets the Emergency Profile Attribute to the Profile B (5b). This will remove the Emergency
    Profile Attribute from Profile A.
            c. If the conditions (5a) is not true, the eUICC aborts the procedure and returns
                 an error to the SM-SR.
(6) The eUICC SHALL send the “ES5.SetEmergencyProfileAttribute” response to the SM-
    SR.
(7) The SM-SR updates the EIS accordingly by adding the information that the Emergency
    Profile has been set on Profile B in the AdditionalProperty field.
(8) Based on ONC, the SM-SR notifies Operator1, whose Profile has the Emergency Profile
    Attribute               Unset,           by                calling              the
    “ES4.HandleEmergencyProfileAttributeUnsetNotification” that its Profile now has the
    Emergency Profile Attribute unset.
(9) Based on ONC, the SM-SR notifies all Operators, having a Profile on this eUICC, by calling
    the “ES4.HandleEmergencyProfileAttributeSetNotification” that a Profile now has the
    Emergency Profile Attribute set. This notification MAY include the Profile ID.
(10) The          SM-SR        notifies   the       M2M       SP      by        calling     the
    "ES4.HandleEmergencyProfileAttributeUnsetNotification" that the Emergency Profile
    Attribute is now unset for Profile A.
    If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
    Operator1, the SM-SR SHALL send this notification to this other Operator by calling the
    "ES4.HandleEmergencyProfileAttributeUnsetNotification".
    If the M2M SP is another Operator connected through its SM-DP and it is authorised by
    Operator1, the SM-SR SHALL send this notification to the SM-DP associated to this other
    Operator by calling the "ES3.HandleEmergencyProfileAttributeUnsetNotification".
    Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting
    as            the           M2M           SP,           by            calling           the
    "ES2.HandleEmergencyProfileAttributeUnsetNotification"
(11) The          SM-SR        notifies the M2M        SP      by    calling   the
    “ES4.HandleEmergencyProfileAttributeSetNotification” that the Emergency Profile
    Attribute is now set for Profile B.
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   Operator2, the SM-SR SHALL send this notification to this other Operator by calling the
   “ES4.HandleEmergencyProfileAttributeSetNotification”.

If the M2M SP is another Operator connected through its SM-DP and it is authorised by Operator2, the SM-SR SHALL send this notification to the SM-DP associated to this other Operator by calling the “ES3.HandleEmergencyProfileAttributeSetNotification”. Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting as the M2M SP, by calling the “ES2.HandleEmergencyProfileAttributeSetNotification” End Conditions: The Profile A has the Emergency Profile Attribute unset. The Profile B has the Emergency Profile Attribute set.

3.27 Fall-Back Attribute Management

This procedure contains the steps needed to change the Fall-Back Attribute from one Profile to another.

The Operator1 needs to grant PLMA for Operator2 in order to authorise to set the Fall -Back Attribute in Operator1 owned Profile, as a consequence, Operator2 owned Profile has the Fall- Back Attribute un-set (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.19). NOTE There is no operation that explicitly un-sets the Fall-Back Attribute on a Profile. The Fall-Back Attribute is only un-set as the consequence of setting the Fall-Back Attribute on another Profile. The sequence flow below describes the procedure.

@startuml skinparam monochrome true skinparam ArrowColor Black

hide footbox

Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF

OP2->SR: [1] ES4.SetFallBackAttribute(EID, ICCID) \non Profile B Request

Rnote over SR #FFFFFF [2] Check PLMA for un-setting Fall-Back Attribute from Operator1 Endrnote

SR-->OP2: [2.a] Return response indicating the PLMA conflict

SR->EUICC: [3] ES5.SetFallBackAttribute on Profile B request

Rnote over EUICC #FFFFFF [4] Unset Fall-Back Attribute on Profile A by Setting Fall-Back Attribute on Profile B Endrnote

EUICC->SR: [5] ES5.SetFallBackAttribute response (euiccResponseData)

Rnote over SR #FFFFFF [6] Update EIS Endrnote

SR->OP2: [7] ES4.SetFallBackAttribute response

SR->OP1: [8] Cond: ES4.HandleProfileFallBackAttributeUnSe tNotification Report

SR->SP: [9] Cond: HandleProfileFallBackAttributeUnsetNotification of Profile A

SR->OP2: [10] Cond: ES4.HandleProfileFallBackAttributeSetNotification Report

SR->SP: [11] Cond: HandleProfileFallBackAttributeSetNotification of Profile B

@enduml

Figure 327: Fall Back Attribute Management Procedure

Start Conditions:
The start conditions are described in GSMA Remote Provisioning Architecture for Embedded
UICC [1].
Procedure:
(1) The Operator2 owning Profile B call “ES4.SetFallBackAttribute” function, providing the
    eid and the iccid of the targeted Profile, in order to set the Fall-Back Attribute to its Profile.
(2) The SM-SR checks if Operator1 has configured a PLMA authorising Operator2 to unset
    the Fall-Back Attribute on Profile A.
            a. If there is a conflict with the authorisation, the SM-SR aborts the procedure
               and informs the Operator 2.
(3) The SM-SR, by calling “ES5.SetFallBackAttribute” function (see section 4.11.7),
    requests the eUICC to set the Fall-Back Attribute to the Profile B.
(4) The eUICC performs the operation. This will remove the Fall-Back Attribute from Profile A.
(5) The eUICC sends the “ES5.SetFallBackAttribute” response to the SM-SR by providing
    the euiccResponseData.
(6) According to the execution status provided by the eUICC, the SM-SR SHALL update the
    EIS to reflect that the Fall-Back Attribute is now set for Profile B.
(7) The SM-SR SHALL send the “ES4.SetFallBackAttribute” response to the Operator2.
(8) Unless Operator1 has set an ONC to not receive those notifications, the SM-SR SHALL
    call the “ES4.HandleProfileFallBackAttributeUnsetNotification” to notify the un-setting
    of the Fall-Back Attribute to the Operator1. In case Operator1 has no direct connection
    with the SM-SR, the SM-SR SHALL send this notification to the SM-DP authorised by
    Operator1 by calling the “ES3.HandleProfileFallBackAttributeUnsetNotification”. Then
    the SM-DP, on reception of this notification, SHALL forward it to Operator1 by calling the
    “ES2.HandleProfileFallBackAttributeUnsetNotification”.
(9) Unless Operator2 has set an ONC to not receive those notifications, the SM-SR sends the
    response back to Operator2
(10) The                SM-SR             SHALL                  send                the
    "ES4.HandleProfileFallBackAttributeUnsetNotification" to an M2M SP, if authorised by
    Operator1 owning the Profile A.
    If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
    Operator1, the SM-SR SHALL send this notification to this other Operator by calling the
    “ES4.HandleProfileFallBackAttributeUnsetNotification”.
    If the M2M SP is another Operator connected through its SM-DP and it is authorised by
    Operator1, the SM-SR SHALL send this notification to the SM-DP associated to this other
    Operator by calling the “ES3.HandleProfileFallBackAttributeUnsetNotification”. Then
    the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting as
    the M2M SP, by calling the “ES2.HandleProfileFallBackAttributeUnsetNotification”.
(11) The SM-SR SHALL send the "ES4.HandleProfileFallBackAttributeSetNotification"
    to an M2M SP, if authorised by Operator2 owning the Profile B.
    If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
    Operator2, the SM-SR SHALL send this notification to this other Operator by calling the
    “ES4.HandleProfileFallBackAttributeSetNotification”.

If the M2M SP is another Operator connected through its SM-DP and it is authorised by Operator2, the SM-SR SHALL send this notification to the SM-DP associated to this other Operator by calling the “ES3.HandleProfileFallBackAttributeSetNotification”. Then the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting as the M2M SP, by calling the “ES2.HandleProfileFallBackAttributeSetNotification”. End Conditions: The Profile B has the Fall-Back Attribute set. The Profile A has the Fall-Back Attribute un- set.

3.28 Fall-Back Attribute Management via SM-DP

This procedure contains the steps needed to change the Fall-Back Attribute from one Profile to another via SM-DP (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.19).

@startuml skinparam monochrome true skinparam ArrowColor Black

hide footbox

Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-DP” as DP #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF

OP2->DP: [1] ES2.SetFallBackAttribute on Profile B\nRequest (SMSR-ID, EID, ICCID)

Rnote over DP #FFFFFF [2] Identify SM-SR Endrnote

DP->SR: [3] ES3.SetFallBackAttibute on Profile B Request (EID, ICCID)

Rnote over SR #FFFFFF [4] Check PLMA for unsetting Fall-Back Endrnote

SR-->DP: [4.a] Return response indicating PLMA conflict

DP->OP2: [4.b] Return response indicating PLMA conflict

SR->EUICC: [5] ES5.SetFallBackAttribute on Profile B request

Rnote over EUICC #FFFFFF [6] Unset Fall-Back Attribute on Profile A by Setting Fall-Back Attribute on Profile B Endrnote

EUICC->SR: [7] ES5.SetFallBackAttribute response (euiccResponseData)

Rnote over SR #FFFFFF [8] Update EIS Endrnote

SRDP: [9] ES3.SetFallBackAttibute response

DPOP2: [10] ES2.SetFallBackAttribute response

SR->OP1: [11] Cond: ES4.HandleProfileFallBackAttributeUnsetNotification Rep ort

SR->SP: [12] Cond: ES4.HandleProfileFallBackAttributeUnsetNotification of Profile A

SR->DP: [13] Cond: ES4.HandleProfileFallBackAttributeSetNotification \nof Profile B

SR->SP: [14] Cond: ES4.HandleProfileFallBackAttributeSetNotification of Profile B

@enduml

Figure 328: Fall-Back Attribute Management via SM -DP

Start Conditions:
The start conditions are described in GSMA Remote Provisioning Architecture for Embedded
UICC [1].
Procedure:
(1) The Operator2 owning Profile B calls “ES2.SetFallBackAttribute” function providing the
    smsr-id of the SM-SR which will manage the operation and the eid and iccid of the targeted
    Profile.
(2) The SM-DP identifies the SM-SR.
(3) The SM-DP calls “ES3.SetFallBackAttribute” function providing the eid and the iccid of
    the targeted Profile.
(4) The SM-SR checks if Operator1 has configured a PLMA authorising Operator2 to unset
    the Fall-Back Attribute on Profile A.
           a. If there is a conflict with the authorisation, the SM-SR aborts the procedure
              and informs the SM-DP.
           b. The SM-DP informs the Operator2 accordingly
(5) The SM-SR, by calling “ES5.SetFallBackAttribute” function (see section 4.11.7),
    requests the eUICC to set the Fall-Back Attribute to the Profile B.
(6) The eUICC performs the operation. This will remove the Fall-Back Attribute from Profile A.
(7) The eUICC sends the “ES5.SetFallBackAttribute” response to the SM-SR by providing
    the euiccResponseData.
(8) According to the execution status provided by the eUICC, the SM-SR SHALL update the
    EIS to reflect that the Fall-Back Attribute is now set for Profile B.
(9) The SM-SR SHALL send the “ES3.SetFallBackAttibute” response to the SM-DP.
(10) The SM-DP SHALL send the “ES2.SetFallBackAttibute” response to the Operator2,
    informing that the Profile B has the Fall-Back Attribute set.
(11) Unless Operator1 has set an ONC to not receive those notifications, the SM-SR
    SHALL call the “ES4.HandleProfileFallBackAttributeUnsetNotification” function to
    notify the Fall-Back Attribute un-setting in Profile A to the Operator1. In case Operator1
    has no direct connection with the SM-SR, the SM-SR SHALL send this notification to the
    SM-DP           authorised        by         Operator1         by         calling      the
    “ES3.HandleProfileFallBackAttributeUnsetNotification”. Then the SM-DP, on
    reception of this notification, SHALL forward it to Operator1 by calling the
    ES2.HandleProfileFallBackAttributeUnsetNotification.
(12) The                SM-SR              SHALL                 send                the
    “ES4.HandleProfileFallBackAttributeUnsetNotification” to an M2M SP, if authorised by
    Operator1 owning the Profile A.
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   Operator1, the SM-SR SHALL send this notification to this other Operator by calling the
   “ES4.HandleProfileFallBackAttributeUnsetNotification”.
   If the M2M SP is another Operator connected through its SM-DP and it is authorised by
   Operator1, the SM-SR SHALL send this notification to the SM-DP associated to this other
   Operator by calling the “ES3.HandleProfileFallBackAttributeUnsetNotification”. Then
   the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting as
   the M2M SP, by calling the “ES2.HandleProfileFallBackAttributeUnsetNotification”.
(13) Unless Operator2 has set an ONC to not receive those notifications, the SM-SR
    SHALL call the “ES4.HandleProfileFallBackAttributeSetNotification” function to notify
    the Fall-Back Attribute un-setting in Profile B to the Operator1. In case Operator1 has no
    direct connection with the SM-SR, the SM-SR SHALL send this notification to the SM-DP
    authorised            by            Operator2            by            calling         the
    “ES3.HandleProfileFallBackAttributeSetNotification”. Then the SM-DP, on reception
    of this notification, SHALL           forward it to Operator2 by calling the
    ES2.HandleProfileFallBackAttributeSetNotification.
(14) The SM-SR SHALL send the "ES4.HandleProfileFallBackAttributeSetNotification”
    to an M2M SP, if authorised by Operator2 owning the Profile B.
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   Operator2, the SM-SR SHALL send this notification to this other Operator by calling the
   “ES4.HandleProfileFallBackAttributeSetNotification”.
   If the M2M SP is another Operator connected through its SM-DP and it is authorised by
   Operator2, the SM-SR SHALL send this notification to the SM-DP associated to this other
   Operator by calling the “ES3.HandleProfileFallBackAttributeSetNotification”. Then the
   SM-DP, on reception of this notification, SHALL forward it to the Operator, acting as the
   M2M SP, by calling the “ES2.HandleProfileFallBackAttributeSetNotification”.
End Conditions:
The Profile B has the Fall-Back Attribute set. The Profile A has the Fall-Back Attribute unset.

3.29 Fall-Back Attribute Management via M2M SP

Operators may also authorise an M2M SP to change the Fall-Back Attribute from one Profile to another. This procedure contains the steps needed to execute such an operation. The Operator1 SHALL authorise the M2M SP the un-setting of the Fall-Back Attribute on its Profile. Operator2 SHALL authorise the M2M SP the setting of the Fall-Back Attribute on its Profile. Such authorisations are granted via PLMA (see GSMA Remote Provisioning Architecture for Embedded UICC [1] section 3.5.20).

@startuml skinparam monochrome true skinparam ArrowColor Black

hide footbox

Participant “M2M SP” as SP #FFFFFF Participant “Operator 1\n<size:10>(owning Profile A)</size>” as OP1 #FFFFFF Participant “Operator 2\n<size:10>(owning Profile B)</size>” as OP2 #FFFFFF Participant “SM-SR” as SR #FFFFFF Participant “eUICC” as EUICC #FFFFFF

SP->SR: [1] ES4.SetFallBackAttribute (EID, ICCID) on Profile B Request

Rnote over SR #FFFFFF [2] Check PLMA for Setting Fall-Back Attribute from Operator 2 Endrnote SR-->SP: [2.a] Send response indicating authorisation conflict

Rnote over SR #FFFFFF [3] Check PLMA for Unsetting Fall-Back Attribute from Operator 1 Endrnote SR-->SP: [3.a] Send response indicating authorisation conflict

SR->EUICC: [4] ES5.SetFallBackAttribute on Profile B request

Rnote over EUICC #FFFFFF [5] Unset Fall-Back Attribute on Profile A by Setting Fall-Back Attribute on Profile B Endrnote

EUICC->SR: [6] ES5.SetFallBackAttribute response (euiccResponseData)

Rnote over SR #FFFFFF [7] EIS Update Endrnote

SR->SP: [8] ES4.SetFallBackAttribute response

SR->OP1: [9] Cond: ES4.HandleProfileFallBackAttributeUnsetNotification of Profile A

SR->SP: [10] Cond: ES4.HandleProfileFallBackAttributeUnsetNotification of Profile A

SR->OP2: [11] Cond: ES4.HandleProfileFallBackAttributeSetNotification of Profile B

SR->SP: [12] Cond: ES4.HandleProfileFallBackAttributeSetNotification of Profile B

@enduml

Figure 329: Fall-Back Attribute Management via M2M SP

Start Conditions:
The start conditions are described in GSMA Remote Provisioning Architecture for Embedded
UICC [1].
Procedure:
(1) The M2M SP calls the “ES4.SetFallBackAttribute” on Profile B to the SM-SR, by
    providing the eid and iccid of the targeted Profile.
(2) The SM-SR checks if a PLMA from Operator2 authorises the M2M SP to set the Fall-Back
    Attribute on Profile B
           a. If there is a conflict with the authorisation, the SM-SR aborts the procedure
              and informs the M2M SP.
(3) The SM-SR checks if a PLMA from Operator1 authorises the M2M SP to unset the Fall-
    Back Attribute on Profile A.
           b. If there is a conflict with the authorisation, the SM-SR aborts the procedure
              and informs the M2M SP.
(4) The SM-SR, by calling “ES5.SetFallBackAttribute” function, requests the eUICC to set
    the Fall-Back Attribute to the Profile B.
(5) The eUICC Sets the Fall-Back Attribute on the Profile B. This will remove the Fall-Back
    Attribute from Profile A.
(6) The eUICC sends the “ES5.SetFallBackAttribute” response to the SM-SR by providing
    the euiccResponseData.
(7) The SM-SR update the EIS accordingly.
(8) The SM-SR SHALL send the “ES4.SetFallBackAttribute” response to the M2M SP.
(9) Unless Operator1 has set an ONC to not receive those notifications, the SM-SR SHALL
    send the “ES4.HandleProfileFallBackAttributeUnsetNotification” to inform the
    Operator1 that the Profile A now has the Fall-Back Attribute unset. In case Operator1 has
    no direct connection with the SM-SR, the SM-SR SHALL send this notification to the SM-
    DP          authorised         by        Operator1           by         calling       the
    “ES3.HandleProfileFallBackAttributeUnsetNotification”. Then the SM-DP, on
   reception of this notification, SHALL forward it to Operator1 by calling the
   “ES2.HandleProfileFallBackAttributeUnsetNotification”.
(10) If    configured by     the    Operator1, the     SM-SR       SHALL    call            the
    “ES4.HandleProfileFallBackAttributeUnsetNotification” to inform the M2M SP.
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   Operator1, the SM-SR SHALL send this notification to this other Operator by calling the
   “ES4.HandleProfileFallBackAttributeUnsetNotification”.
   If the M2M SP is another Operator connected through its SM-DP and it is authorised by
   Operator1, the SM-SR SHALL send this notification to the SM-DP associated to this other
   Operator by calling the “ES3.HandleProfileFallBackAttributeUnsetNotification”. Then
   the SM-DP, on reception of this notification, SHALL forward it to the Operator, acting as
   the M2M SP, by calling the “ES2.HandleProfileFallBackAttributeUnsetNotification”.
(11) Unless Operator2 has set an ONC to not receive those notifications, the SM-SR
    SHALL send the “ES4.HandleProfileFallBackAttributeSetNotification” to inform the
    Operator2 that the Profile B now has the Fall-Back Attribute set. In case Operator2 has no
    direct connection with the SM-SR, the SM-SR SHALL send this notification to the SM-DP
    authorised            by          Operator2             by             calling         the
    “ES3.HandleProfileFallBackAttributeSetNotification”. Then the SM-DP, on reception
    of this notification, SHALL          forward it to Operator2 by calling the
    “ES2.HandleProfileFallBackAttributeSetNotification”.
(12) If    configured by     the    Operator2, the     SM-SR        SHALL   call            the
    “ES4.HandleProfileFallBackAttributeSetNotification” to inform the M2M SP.
   If the M2M SP is another Operator directly connected to the SM-SR and it is authorised by
   Operator2, the SM-SR SHALL send this notification to this other Operator by calling the
   “ES4.HandleProfileFallBackAttributeSetNotification”.
   If the M2M SP is another Operator connected through its SM-DP and it is authorised by
   Operator2, the SM-SR SHALL send this notification to the SM-DP associated to this other
   Operator by calling the “ES3.HandleProfileFallBackAttributeSetNotification”. Then the
   SM-DP, on reception of this notification, SHALL forward it to the Operator, acting as the
   M2M SP, by calling the “ES2.HandleProfileFallBackAttributeSetNotification”.
End Conditions:
The Profile B has the Fall-Back Attribute set. The Profile A has the Fall-Back Attribute unset.

3.30 Local Enable for Emergency Profile

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 120 skinparam sequenceArrowThickness 1

hide footbox

participant “Device” as DEV #FFFFFF participant “eUICC” as eUICC #FFFFFF

DEV->>eUICC : (1) ESx.LocalEnableEmergencyProfile
Rnote over eUICC #FFFFF
(2) Verify that the Emergency Profile exists
Endrnote
eUICC-->>DEV : Error
Rnote over eUICC #FFFFF
(3) Verify that the currently Enabled Profile
     is NOT the Emergency Profile
Endrnote
eUICC-->>DEV : Error

group Profile switch Rnote over eUICC #FFFFF (4) Enable Emergency Profile Endrnote eUICC-->>DEV : (5) Success ||| eUICC->>DEV: (6) REFRESH, (UICC reset) ||| Rnote over DEV, eUICC #FFFFFF (7) Network attachment with the Emergency Profile Endrnote end

@enduml

Figure 330: Local Enable of Emergency Profile

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:
   (1) The Device SHALL call the “ESx.LocalEnableEmergencyProfile” function.
   (2) The eUICC SHALL verify that the Emergency Profile (Profile with the Emergency
       Profile Attribute set) exists on this eUICC. If the condition to be verified is not satisfied,
       the eUICC SHALL return a response indicating the failure, and the procedure SHALL
       end.
   (3) The eUICC SHALL verify that the current Enabled Profile is NOT already the
       Emergency Profile. If the condition to be verified is not satisfied, the eUICC SHALL
       return a response indicating that the Emergency Profile is already Enabled, and the
       procedure SHALL end.
   (4) The eUICC SHALL NOT enforce POL1 of the currently Enabled Profile, and SHALL
       disable the currently Enabled Profile and enable the Emergency Profile.

NOTE:Profile change includes a change of the IMSI that is used to attach to the network. As indicated in 3GPP TS 31.102 [52], such a change requires special caution and should always be accompanied by a REFRESH command to avoid inconsistent information being read by the terminal. So

while the Profile is marked as enabled in this step, it MAY actually become
effective after the terminal executes the REFRESH command.
(5) The eUICC SHALL return the successful execution status of the “ ESx.
    LocalEnableEmergencyProfile” command to the Device.
(6) The eUICC SHALL send a REFRESH proactive command in UICC reset mode to the
    Device. This will trigger the execution of a network attach procedure.
(7) The Device SHALL perform a network attach procedure with the newly enabled Profile.

NOTE:Whether the Emergency Profile provides connectivity to a test network or not, the eUICC will not attempt to enable automatically the previously Enabled Profile. This is in contrast to the remote enable procedure s (for example in section 3.2.2).

3.31 Local Disable for Emergency Profile

@startuml skinparam monochrome true skinparam ArrowColor Black skinparam maxmessagesize 450 skinparam ParticipantPadding 100 skinparam sequenceArrowThickness 1

hide footbox

participant “Device” as DEV #FFFFFF participant “eUICC” as ISDR #FFFFFF

DEV->>ISDR : (1) ESx.LocalDisableEmergencyProfile

Rnote over ISDR #FFFFF
(2) Verify that the currently Enabled profile
     is the Emergency Profile
Endrnote
ISDR-->>DEV : Error
group Profile switch
Rnote over ISDR #FFFFF
(3) Disable Emergency Profile and
      enable previously Enabled Profile
Endrnote
ISDR-->>DEV : (4) Sucess
|||
ISDR->>DEV: (5) REFRESH, (UICC reset)
|||
Rnote over DEV, ISDR #FFFFFF
(6) Network attachment with the Enabled Profile
Endrnote
End
@enduml

Figure 331: Local Disable of Emergency Profile

Start Conditions: The start conditions are described in GSMA Remote Provisioning Architecture for the Embedded UICC [1].

Procedure:
    (1) The Device SHALL call the “ESx.LocalDisableEmergencyProfile” function.
    (2) The eUICC SHALL verify that the currently Enabled Profile is the Emergency Profile
        (Emergency Profile attribute set). If the condition to be verified is not satisfied, the
        eUICC SHALL return a response indicating that the Emergency Profile is not Enabled,
        and the procedure SHALL end.
    (3) The eUICC SHALL NOT enforce POL1 of the Enabled Emergency Profile, and SHALL
        disable the Emergency Profile and enable the previously Enabled Profile.

NOTE:The previously Enabled Profile is the Profile that was Enabled, before the Emergency Profile was enabled by the “ESx.LocalEnableEmergencyProfile” command.

    (4) The eUICC SHALL return the successful execution                         status       of   the
        “ESx.LocalDisableEmergencyProfile” command to the Device.
    (5) The eUICC SHALL send a REFRESH proactive command in UICC reset mode to the
        Device. This will trigger the execution of a network attach procedure.
   (6) The eUICC and the Device SHALL perform a network attach procedure with the newly
        Enabled Profile.
Dependent on the configuration of the eUICC, the eUICC MAY send a Notification about the
Profile change after Emergency Profile disabling to the SM-SR.

4 eUICC Interface Descriptions

This section contains the technical descriptions of those interfaces within the Remote Provisioning and Management system involving the eUICC directly, including the following:

    ES5, interface between the SM-SR and the eUICC.
    ES6, interface between the Operator and the eUICC
    ES8, interface between the SM-DP and the eUICC.
    ESx, interface between the Device and the eUICC.

The following table presents the normative list of all the functions that are defined in this section.

Request-response functions:

                                                                                 Function
  Interface      Function group                  Functions
                                                                              prov ider entity
ES5           Platform Management   CreateISDP                                    ISD-R

EnableProfile

DisableProfile
DeleteProfile

eUICCCapabilityAudit

MasterDelete

SetFallbackAttribute

SetEmergencyProfileAttribute

EstablishISDRKeySet

eUICC Management     FinaliseISDRhandover

UpdateSMSRAddressingParameters

                                 UpdatePOL1byMNO
ES6         Profile Management                                               MNO-SD
                                 UpdateConnectivityParametersByMNO

DownloadAndInstallation

ES8         Profile Management   EstablishISDPKeySet                          ISD-P

UpdateConnectivityParameters SCP03

LocalEnableEmergencyProfile

LocalDisableEmergencyProfile

ESx         Local Management

LocalEnableTestProfile

LocalDisableTestProfile

Table 5:: Request Response Functions

Notification handler functions:

                                                                                                                Function
 Interface       Function group                         Notification handler functions
                                                                                                              prov ider Role
                                         HandleDefaultNotification
ES5           Platform Management                                                                                SM-SR
                                         HandleNotificationConfirmation

Table 6: Notification Handler Functions

4.1 Functions Description

NOTE:If any command, such as Profile Enabling, Profile Disabling, and Profile Download and Installation does not complete successfully, the eUICC SHALL maintain the state it was in before it received the command.

4.1.1 ES5 (SM-SR–eUICC) Interface Description

4.1.1.1 ISD-P Creation

Function name: CreateISDP

Related Procedures: ISD-P creation

Function group: Platform Management

Function Provider entity: ISD-R

Description: This function creates an ISD-P on the eUICC.

Parameters:

 ISD-P-AID  Cumulative Granted Non Volatile Memory for the ISD-P (optional) Prerequisite:

 The SM-SR has assigned an ISD-P-AID. Command Description:

INSTALL COMMAND

The command is an Install command as defined in GlobalPlatform Card Specification [6].

The following tables describe the installation command and the specific parameters within the data field:

Code    Value                                Meaning
CLA         ‘80’        See GlobalPlatform Card Specification section 11.1
INS         ‘E6’        INSTALL
P1         ‘0C’        See GlobalPlatform Card Specification [6] section 11.5.2.1
P2         ‘00’        See GlobalPlatform Card Specification [6] section 11.5.2.2
Code       Value                                     Meaning
Lc         ‘xx’           Data Field Length
Data        ‘xxxx…’        See GlobalPlatform Card Specification [6] section 11.5.2.3
Le         ‘00’

Table 7: INSTALL Command Message

Reference Control Parameter P1

b8 b7 b6 b5 b4 b3 b2 b1 Meaning

0       0   0   0   1   0     0       0    For make selectable
0       0   0   0   0   1     0       0    For Install

Table 8: INSTALL Reference Control Parameter P1

Reference Control Parameter P2 – ISD-P State Coding

P2 is set to ‘00’; according to GlobalPlatform Card Specification [6] section 11.5, this means no information provided.

Data Field

Name                                     Length         Value Description          MOC
 Length of Executable Load File AID ’1’                 ‘05’ - ‘10’                M
Executable Load File AID                 ‘05’ – ‘10’ ‘xxxx’                        M
Length of Executable Module AID          ‘1’            ‘05’ - ‘10’                M
Executable Module AID                    ‘05’ – ‘10’ ‘xxxx’                        M
Length of Application AID                ‘1’            ‘05’ - ‘10’                M
Application AID (ISD-P-AID)              ‘05’ – ‘10’ ‘xxxx’                        M
Length of Privileges                     ‘1’            ‘01’ - ‘03’                M
Privileges                               ‘1’or ‘3’      See [6] section 11.1.2     M
Length of Install Parameters field       ’2’-‘n’                                   M
Install Parameters field                 ‘0-n’          See [6] section 11.5.2.3.7 M
Length of Install Token                  ‘1’            00                         M

Table 9: INSTALL Command Data Field

Privileges

Privileges granted to the ISD-P, as specified in Annex C, SHALL be at least:

   Security Domain
   Trusted Path
   Authorized Management

Install Parameters

Tag   Length                                    Value Description                                              MOC
‘C9’             Application Specific Parameters: see GlobalPlatform Card Specification [6] section             M
       ‘1-n’     11.5.3.2.
Tag    Length                               Value Description                                MOC
                                                                                              M (n
'81'   2            Secure Channel Protocol Identifier and Implementation Option “i”
                                                                                          occurrences)
‘EF’   ‘1-n’     System Specific Parameters                                                                     O
Tag    Length                               Value Description                                MOC
'83'   ‘2’ or ‘4’   Cumulative Granted Non Volatile Memory                                     O

Table 10: INSTALL Parameters

Data Returned

None

Response Message

Data Field Returned in the Response Message:

A single byte of '00' SHALL be returned indicating that no additional data is present, as defined in the GlobalPlatform Card Specification [6] section 11.5.3.1.

Processing State returned in the Response Message:

See GlobalPlatform Card Specification [6] section 11.5.3.2.

4.1.1.2 Profile Enabling

Function name: EnableProfile

Related Procedures: Profile Enabling

Function group: Platform Management

Function Provider entity: ISD-R

Description: This function is used to enable a Profile on the eUICC.

The function makes the target Profile enabled, and disables implicitly the currently Enabled Profile.

Parameters:

      ISD-P-AID

Prerequisites:

      SM-SR has checked that POL2 of both the currently Enabled Profile and the target
       Profile allow this action.
      The target Profile SHALL NOT be the Test Profile

Function Flow

Upon reception of the Profile Enabling command, the eUICC SHALL:

   Verify that the target Profile is in the disabled state
   Verify that POL1 of the currently Enabled Profile allows its disabling
   Verify that the target Profile is not the Test Profile
   If any of these verifications fail, terminate the command with an error status word
   If the current profile has been enabled by the activation of the Fall-Back Mechanism
    then
        If the target Profile is not the previously Enabled profile and the POL1 of the
         previously enabled profile does not allow its own disabling, or contains the rule
         “Profile deletion is mandatory when its state is changed to disabled ”, terminate the
         command with an error status word
   Disable the currently Enabled Profile and Enable the target Profile
   Send the REFRESH command in “UICC Reset” mode to the Device according to
    ETSI TS 102 223 [3]

NOTE:The eUICC SHALL send the command response (over SMS PoR or HTTP POST or CAT-TP SDU) before issuing the proactive command REFRESH. So it is possible but not required that the eUICC send the REFRESH command immediately. However the eUICC SHALL issue the REFRESH command within a time interval of 10 STATUS events after receiving the enable command.

   Send notification.

Command Description:

STORE DATA COMMAND

This command is a STORE DATA command, as described in GlobalPlatform Card Specification [6].

        Code              Value                             Meaning
CLA                ‘80’
INS                ‘E2’            STORE DATA
P1                 ‘88’            Reference Control Parameter P1 0
P2                 ‘00’            Block Number (Not used for Enable command)
Lc                 ‘XX’            Length of data field
Data               ‘XX’            Application Data and MAC (if present)
Le                 Not present

Table 11: STORE DATA COMMAND Message

Parameter P1 is coded according to the following table:

b8 b7 b6 b5 b4 b3 b2 b1 Meaning
1    -     -   -   -   -      -   -    Last block
-    0     0   -   -   -      -   -    No general encryption information or non-encrypted data
-    -     -   0   1   -      -   -    DGI format of the command data field
-    -     -   -   -   X      X   X    RFU

Table 12: STORE DATA Reference Control Parameter P1

Data Field Sent in the Command Message

      DGI              Length                                    Value Description                            MOC
'3A03'           Var                Enable Profile                                                            M
                                        Tag           Length                   Value Description              MOC
'4F'           5-16                ISD-P-AID                              M

Table 13: Enable Attribute Data Field

Response Message

Data Field Returned in the Response Message:

The data field of the response message SHALL NOT be present.

Processing State returned in the Response Message:

See GlobalPlatform Card Specification [6] section 11.11.3.2.

Specific Processing State returned in response Message:

’69 85’: Profile is not in the Disabled state, or Profile is the Test Profile.

’69 E1’: POL1 of the currently Enabled Profile or of the previously enabled profile prevents this action.

4.1.1.3 Profile Disabling

Function name: DisableProfile

Related Procedures: Profile Disabling

Function group: Platform Management

Function Provider entity: ISD-R

Description: This function is used to disable a Profile on the eUICC.

This function makes the target Profile Disabled, and implicitly enables the Profile which has the Fall-Back Attribute set.

Parameters:

 ISD-P-AID of the currently Enabled Profile Prerequisites:

 SM-SR has checked that POL2 allows this action  The target Profile SHALL NOT be the Test Profile Function flow

Upon reception of the Profile Disabling command, the eUICC SHALL:
    Verify that the target Profile is in Enabled state
    Verify that POL1 of the currently Enabled Profile allows its disabling
    Verify that the target Profile is not the Test Profile
    Verify that the target Profile is not the Profile with Fall-Back Attribute set
    If any of these verifications fail, terminate the command with an error status word.
    Disable the target Profile and enable the Profile with the Fall-Back Attribute set
    Send the REFRESH command in “UICC Reset” mode to the Device according to
      ETSI TS 102 223 [3].
Note:        The same note about deferred REFRESH as for enable command applies
             as well to disable: The eUICC SHALL issue the REFRESH command within
             a time interval of 10 STATUS events after receiving the disable command.

Command Description:

STORE DATA COMMAND

This command is a STORE DATA command, as described in GlobalPlatform Card Specification [6].

Code      Value                        Meaning
CLA    ‘80’
INS    ‘E2’          STORE DATA
P1     '88'          Reference control parameter P1
P2     ‘00’          Block Number (Not used for Enable command)
Lc     ‘xx’          Length of data field
Data   ‘xx’          Application Data and MAC (if present)
Le     Not present

Table 14: STORE DATA Command Message

Reference Control Parameter P1

b8    b7        b6   b5   b4    b3     b2    b1    Meaning
1     -         -    -    -     -      -     -     Last block
-     0         0    -    -     -      -     -     No general encryption information or non-encrypted data
-     -         -    0    1     -      -     -     DGI format of the command data field
-     -         -    -    -     X      X     X     RFU

Table 15: STORE DATA Reference Control Parameter P1

Data Field Sent in the Command Message

      DGI                   Length                                    Value Description                                  MOC
'3A04'                Var                  Disable Profile                                                               M
Tag             Length                Value Description                     MOC
'4F'         5-16                ISD-P-AID                                    M

Table 16: Disable Attribute Data Field

Response Message

Data Field Returned in the Response Message:

The data field of the response message SHALL NOT be present.

Processing State returned in the Response Message:

See GlobalPlatform Card Specification [6] section 11.11.3.2.

Specific Processing State returned in response Message:

’69 85’: Profile is not in the Enabled state or Profile has the Fall-Back Attribute set or Profile is the Test Profile.

’69 E1’: POL1 of the Profile prevents disabling.

4.1.1.4 Profile Deletion

Function name: DeleteProfile

Related Procedures: Profile and ISD-P deletion, Profile and ISD-P deletion via SM-DP

Function group: Platform Management

Function Provider entity: ISD-R

Description: This function is used to delete a Profile from the eUICC.

This function deletes the ISD-P and its associated Profile.

Parameters:

 ISD-P-AID Prerequisites:

 SM-SR SHALL check that POL2 allows this action  The target Profile SHALL NOT be the Profile with the Fall-Back Attribute set  The target Profile SHALL NOT be the Test Profile Function flow

Upon reception of the DELETE command, the eUICC SHALL:

   If the Profile is in Disabled state:
     Verify that POL1 of the target Profile allows its deletion. This includes, if the target
         Profile has been Disabled by the activation of the Fall-Back Mechanism described
         in section 3.16, verify that POL1 of the target Profile allows Disabling.
   Verify that the target Profile is not the Profile with Fall-Back Attribute set
   Verify that the target Profile is not the Test Profile
   Verify that the target Profile is not in the Enabled state
   If any of these verifications fail, terminate the command with an error status word
   Delete the ISD-P with its Profile.

NOTE:An incomplete Profile (i.e. the ISD-P is still in state SELECTABLE or PERSONALIZED) can always be deleted.

Command Description:

DELETE COMMAND

This function is realised through the GlobalPlatform DELETE command as defined in GlobalPlatform Card Specification Amendment C [9].

Command Message

The DELETE command message SHALL be coded according to the following table:

Code   Value                                     Meaning
CLA    '80' - '8F', 'C0' - 'CF' or 'E0' - 'EF'   See section 11.1.4 of GlobalPlatform Card Specification [6]
INS    'E4'                                      DELETE
P1     '00'                                      Reference control parameter P1
P2     '40'                                      Reference control parameter P2
Lc     'xx'                                      Length of data field
Data   'xxxx…'                                   TLV coded objects (and MAC if present)
Le     '00'

Table 17: DELETE Command Message

Reference Control Parameter P1

b8       b7       b6       b5       b4     b3     b2   b1   Meaning
0        -        -        -        -      -      -    -    Last (or only) command
-        X        X        X        X      X      X    X    RFU

Table 18: DELETE Reference Control Parameter P1

Reference Control Parameter P2

b8   b7   b6    b5       b4       b3       b2       b1                                 Meaning
0    1    –     –        –        –        –        –        Delete a root security domain and all associated Applications
–    –    X     X        X        X        X        X        RFU

Table 19: DELETE Command Reference Control Parameter P2

Data Field Sent in the Command Message

The data field of the DELETE command message SHALL contain the TLV coded name(s) of the object to be deleted.

Tag          Length          Value Description   MOC
'4F'         5-16            ISD-P-AID           M

Table 20: DELETE [card content] Command Data Field

Response Message

Data Field Returned in the Response Message:

A single byte of '00' SHALL be returned indicating that no additional data is present.

Processing State Returned in the Response Message:

As defined in GlobalPlatform Card Specification [6] section 11.2.3.2.

Specific Processing State returned in response Message:

’69 85’: Profile is in Enabled State or Profile has the Fall-Back Attribute or Profile is the Test Profile.

’69 E1’: POL1 of the Profile prevents deletion (including the case where the Profile has been Disabled by the activation of the Fall-Back Mechanism, and its POL1 prevents disabling).

4.1.1.5 eUICC Capability Audit

Function name: eUICCCapabilityAudit

Related Procedures: -

NOTE:This function is not present in any procedure, however, it MAY be used and requested at any point of time by the Profile owner or SM-SR.

Function group: Platform Management

Function Provider entity: ISD-R

Description: This function is used to query the status of the eUICC.

Parameters:

It may be used to ensure the data within the SM-SR’s EIS database is up to date. This function uses two commands which SHALL be implemented as an extension of the GlobalPlatform functions GET DATA and GET STATUS.

GET DATA

This function can return:

   Number of installed ISD-P and available not allocated memory
   ECASD Certificate

GET STATUS

This function can return:

   Each ISD-P-AID
   State of the ISD-Ps / Profiles

Prerequisites:

   None

Commands Description:

GET DATA

The GET DATA command is coded according to the following table:

Code Value                              Meaning
CLA    ‘80’   See GlobalPlatform Card Specification section 11.1.4.1
INS    ‘CA’   GET DATA
P1     ‘xx’   See below
P2     ‘xx’   See below
Lc     ‘xx’   Not present if no command data, otherwise length of data field
Data   ‘xxxx…’ Not present, or command data
Le     ‘00’

Table 21: GET DATA Command Message

Parameter P1 and P2

The P1 and P2 parameters define the tag of the data object to be read.

Tag ‘FF 21’: Extended Card Resources Information available for Card Content Management, as defined in ETSI TS 102 226 [5].

Tag ‘BF 30’: Forwarded CASD Data mechanism as defined in GlobalPlatform Card Specification Amendment C [9].

This mechanism allows to retrieves ECASD data through the ISD-R.

Data field

If the P1 and P2 parameters are set to ‘BF 30’, the data field SHALL include one (and only one) of the following requests:

 ECASD recognition data: ‘5C 01 66’  ECASD Certificate Store (containing ECASD Public Key Certificates): ‘5C 02 7F 21’ Response Message

If certificate data is requested, the certificate SHALL be returned TLV-coded as follows:

Name                              Length       Value Description                                               MOC
Forwarded CASD Data tag           2            ‘BF 30’                                                         C
Length of the response            1, 2 or 3 '00' - '7F', or '81 80' - '81 FF' or '82 01 00' - '82 FF FF'       C
Certificate store tag             2            ‘7F 21‘                                                         M
Length of the certificate 1, 2 or 3            '00' - '7F', or '81 80' - '81 FF' or '82 01 00' - '82 FF FF' M
Certificate data             n                 ‘xxxx…’                                                    M

Table 22: GET DATA Command Data Field

Certificate Data

The following table describes the certificate data which will be returned by the eUICC Capability Audit command.

Tag             Length           Value Description                                                                            MOC
'7F21'          Var.             Certificate                                                                                  M
Tag           Length                           Value Description                             MOC
'93'          1-16               Certificate Serial Number                                   M
'42'          1-16               CA Identifier (value part of the DER-TLV                    M
                                 encoding of the EUM OID e.g. bytes=
                                 2B06010401… for OID=1.3.6.1.4.1….).
'5F20'        16                 Subject Identifier (EID                                     M
'95'          2                  Key Usage                                                   M
                                 ‘0080’: Key Agreement
'5F25'    4                 Effective Date (YYYYMMDD, BCD format)                 M
'5F24'    4                 Expiration Date (YYYYMMDD, BCD format)                M
‘45’      1-16              ECASD Image Number (ISDN)                             M
'73'      Var.              Discretionary Data:                                   M
Tag      Length      Value Description
'C0'     var         eUICC          Supplier
                     Identifier
'C1'     var         eUICC Product       Line
                     Identifier
'C2'     var         eUICC Extended GSMA
                     SAS Accreditation Serial
                     Number
‘C9’     20          Authority key identifier
                     (value of the Subject
                     Key Identifier extension
                     of the EUM certificate)

Other TLVs MAY be present

'7F49'    Var.              Public Key                                            M
'5F37'    Var.              Signature (to be computed as described in             M
                            GlobalPlatform Card Specification Amendment
                            E [11] and the signature SHALL include all the
                            field starting from tag '93' to tag '7F49')

Table 23: eUICC Certificate Data Fields

Public Key Data Object

The public key data object contains an elliptic curves (EC) public key and the corresponding domain parameters.

      Tag      Length                              Value Description                                 MOC
'7F49'       Var.         Public Key Data Object                                                      M
Tag         Length                        Value Description                MOC
'B0'        Var                Public key – Q                               M
'F0'        '01'               Key Parameter Reference                      M
                               ‘00’: NIST P-256
                               ‘03’: brainpoolP256r1
                               ‘40’: FRP256V1 [51]

Table 24: Public Key Data Object Data Field

An ECASD SHALL have at least one set of elliptic curve parameters preloaded (see GlobalPlatform Card Specification Amendment E [11]) as defined in the table above.

GET STATUS

The GET STATUS command is coded according to the following table:

Code    Value                                                          Meaning
CLA    ‘80’              See GlobalPlatform Card Specification [6] section 11.1.4.1
INS    ‘F2’              GET STATUS
P1     ‘40’              See GlobalPlatform Card Specification [6] section 11.4.2.1.
P2     ‘xx’              See GlobalPlatform Card Specification [6] section 11.4.2..2.
Lc     ‘xx’              Length of the data field
Data   ‘4F xx …’ See GlobalPlatform Card Specification [6] section 11.4.2.3.
Le     ‘00’

Table 25: GET STATUS Command Message

Parameter P1

The following value will be used for P1:

‘40’ – Applications and Supplementary Security Domains only

Parameter P2

The parameter P2 controls the number of consecutive GET STATUS commands.

b8     b7        b6    b5   b4        b3   b2   b1                            Meaning
X      X       X       X    X     X        -    -    RFU
-      -       -       -    -     -                  Response Data Structure according to table 11 -36 of
                                           1    -    GlobalPlatform Card Specification [6].
-      -       -       -    -     -        -    0    Get first or all occurrence(s)
-      -       -       -    -     -        -    1    Get next occurrence(s)

Table 26: GET STATUS Command Reference Control Parameter P2

Data field sent in the Command Message

The GET STATUS command message data field SHALL contain at least one TLV coded search qualifier: the AID (tag ‘4F’). It SHALL be possible to search for all the occurrences that match the selection criteria according to the reference control parameter P1 using a search criteria of ‘4F 00’.

The search is limited to the ISD-P instances.

The following other search criteria SHALL be supported: Life Cycle State (tag ‘9F70’) and ISD-P Attributes (tag ‘53’).

The tag list (tag ‘5C’) indicates to the UICC how to construct the response data for each eUICC entity matching the search criteria.

The data field is structured as follows:

              Tag                          Length             Value Description         MOC
‘4F’                            0-16                       Application AID              M
‘xx’ or ‘xxxx’                  0-n                        Other search criteria        O
                Tag                         Length             Value Description         MOC
…                                  …                       …                              …
‘5C’                               1-n                     Tag list                       M

Table 27: GET STATUS Command Data Field

Response Message

Data Field Returned in the Response Message:

The tag list (tag ‘5C’) identifies the extended information for ISD-P. The coding of the response message is defined as followed:

Tag    Length                                                        Name                                                    MOC
‘E3’ Variable GlobalPlatform Registry related data                                                                           M
 Tag       Length                                          Name                                          MOC
'4F'       5-16      AID                                                                                 M
'9F70' 1             Life Cycle State                                                                    C
'53'       1         ISD-P Properties (see Table 29)                                                     C
‘8F’       2 or 4    Cumulative Granted Non-Volatile Memory as defined in GlobalPlatform Specification   C
                     v2.2 amendment C [9]
‘91’       2 or 4    Cumulative Remaining Non-Volatile Memory as          defined in GlobalPlatform      C
                     Specification v2.2 amendment C [9]

Table 28: GET STATUS Command Data Field Return

If an ISD-P that matches the search criteria was installed without Cumulative Granted Memory option, the related tags ‘8F’ and ‘91’ SHALL be absent in the response, even if they were requested in the tag list of the command.

b8 b7 b6 b5 b4 b3 b2 b1                                                   Meaning
X          X       X     X     X       -    -   -    RFU
-          -       -     -     -       X    X   0    Fall-Back Attribute not set
-          -       -     -     -       0    0   1    Fall-Back Attribute set
-          -       -     -     -       X    0   X    Emergency Profile Attribute not set
-          -       -     -     -       0    1   0    Emergency Profile Attribute set
-          -       -     -     -       0    X   X    Test Profile Flag not set
-          -       -     -     -       1    0   0    Test Profile Flag set
                                   Table 29: ISD-P Properties

ISD-P State Coding

The life cycle of the ISD-P is coded as define in section 2.2.1.3.

Processing State returned in the Response Message:

As defined in GlobalPlatform Card Specification [6] section 11.3.3.2.

4.1.1.6 Master Delete

Function name: MasterDelete

Related Procedures: Master Delete Procedure

Function group: Platform Management

Function Provider entity: ISD-R

Description: This function deletes a target Profile on the target eUICC regardless of POL1 rules. This function SHALL use the ISD-P token verification key(AES key with key version number ‘70’ and key identifier ‘01’) in order to authenticate the source of the command.

Parameter:

     ISD-P-AID
     Delete Token, calculated as defined in GlobalPlatform Card Specification Amendment
      D [10] , provided by the SM-DP
Prerequisites:

 The target Profile SHALL NOT be the Profile which has the Fall-Back Attribute set.  The target Profile SHALL be in the Disabled state. Function flow

Upon reception of the Master Delete command, the eUICC SHALL:

      Verify that the target Profile is in the Disabled state
      Verify that the target Profile is not the Profile with Fall-Back Attribute set
      Verify the Token (actually performed by the ISD-P). This includes verifying the
       signature of the Token, and verifying that the values of tags 42, 45, and 5F20 in the
       Token match the corresponding values in the ISD-P.
      If any of these verifications fail, terminate the command with an error status word.
      Delete the ISD-P with its Profile, regardless of POL1.

As token protection is only used by this command, this token SHALL be processed by the ISD- P even though the ISD-P does not have the token verification privilege. No receipt SHALL be generated by the command. The eUICC SHALL support setting the value of tags 42, 45, and 5F20 by a STORE DATA command defined in GlobalPlatform Card Specification [6]. If the value of tag 5F20 is not set by the SM-DP, the default value SHALL be the value of the RID of ISD-P defined in section 2.2.3.

NOTE1:This deviates from the typical handling of tokens by SDs.

NOTE 2:The SM-DP MAY set the values of tags 42, 45 and 5F20 during profile download.

Command Description:

This function is realised through the GlobalPlatform DELETE command as defined in GlobalPlatform Card Specification Amendment C [9].

Command Message

DELETE COMMAND

The DELETE command message SHALL be coded according to the following table:

Code        Value                                                        Meaning
CLA         ‘80’ – ‘8F’, ‘C0’ – ‘CF’ or ‘E0’ – ‘EF’                      See section 11.1.4 of GlobalPlatform Card Specification [6]
INS         ‘E4’                                                         DELETE
P1          ‘00’                                                         Reference control parameter P1
P2          ‘40’                                                         Reference control parameter P2
Lc          ‘xx’                                                         Length of data field
Data        ‘xxxx…’                                                      TLV coded objects (and MAC if present)
Le          ‘00’

Table 30: DELETE Command Message

Reference Control Parameter P1

b8        b7       b6       b5       b4        b3   b2     b1    Meaning
0         -        -        -        -         -    -      -     Last (or only) command
-         X        X        X        X         X    X      X     RFU

Table 31: DELETE Reference Control Parameter P1

Reference Control Parameter P2

b8      b7     b6      b5        b4       b3       b2       b1        Meaning
0       1      –       –         –        –        –        –         Delete a root security domain and all associated Applications
–       –      X       X         X        X        X        X         RFU

Table 32: DELETE Command Reference Control Parameter P2

The Delete [card content] Data Field SHALL contain the following parameters:

Tag                             Length                                                Value Description                             MOC
‘4F’                       5-16                                   ISD-P-AID to be deleted                                                      M
‘B6’                       Var.                                   Control Reference Template for Digital Signature                             M
Tag            Length          Value Description                MOC
                                  Identification Number of the
‘42’                 1-n                                                     M
                                  ISD-P
‘45’                 1-n          Image Number of the ISD-P                  M
‘5F20’               1-n          Application Provider identifier            M
‘93’                 1-n          Token identifier number                    M
Tag               Length                    Value Description                     MOC
‘9E’                  1-n             Delete Token                                           M

Table 33: DELETE [card content] Command Data Field

Response Message

Data Field Returned in the Response Message:

A single byte of ‘00’ SHALL be returned indicating that no additional data is present.

Processing State Returned in the Response Message:

As defined in GlobalPlatform Card Specification [6] section 11.2.3.2.

Specific Processing State returned in response Message:

’69 85’: Profile is not in the Disabled state or Profile has the Fall-Back Attribute set.

4.1.1.7 Set Fall-Back Attribute

Function name: SetFallbackAttribute

Related Procedures: -

Function group: Platform Management

Function Provider entity: ISD-R

Description: This function sets the Fall-Back Attribute for one Profile on the target eUICC.

Parameters:

 ISD-P-AID Prerequisites:

 The Profile to be assigned the Fall-Back Attribute must have Provisioning capability. Function flow

Upon reception of the STORE DATA command, the eUICC SHALL:

      Set the Fall-Back Attribute for the target Profile
      Remove the Fall-Back Attribute from the Profile that has the attribute currently
       assigned

Setting of the Fall-Back Attribute is done via ISD-R.

If the currently Enabled profile is the Profile with the Fall-Back Attribute set, and has been Enabled by the activation of the Fall-Back Mechanism, and the previously Enabled Profile has either of the POL1 rules “Disable not allowed” or “Profile deletion is mandatory when its state is changed to Disabled” set, then the eUICC SHALL prevent the execution of the function “Set Fall-Back Attribute”.

Command Description:

STORE DATA Command

This function is realised through the GlobalPlatform STORE DATA command as defined in GlobalPlatform Card Specification [6].

Command Message

The STORE DATA command message SHALL be coded according to the following table:

Code Value                                            Meaning
CLA        ‘80’ – ‘8F’, ‘C0’ – ‘CF’ or ‘E0’ – ‘EF’ See section 11.1.4 of GlobalPlatform Card Specification [6]
INS        ‘E2’                                       STORE DATA
P1         ‘88’                                       Reference control parameter P1
P2         ‘00’                                       Block number
Lc         ‘xx’                                       Length of data field
Data       ‘xxxxx…’                                   Application data and MAC (if present)
Le                                                    Not present

Table 34: STORE DATA Command Message

Reference Control Parameter P1

b8     b7         b6   b5    b4      b3   b2     b1    Meaning
1      -          -    -     -       -    -      -     Last block
-      0          0    -     -       -    -      -     No general encryption information or non-encrypted data
-      -          -    0     1       -    -      -     DGI format of the command data field
-      -          -    -     -       X    X      X     RFU

Table 35: STORE DATA Reference Control Parameter P1

Data Field Sent in the Command Message

DGI                Length                                      Value Description                                 MOC
‘3A05’             Var                    Set Fall-Back Attribute                                                        M
Tag           Length                 Value Description                   MOC
‘4F’            5-16            ISD-P-AID                                      M

Table 36: Set Fall-Back Attribute Data Field

Response Message

Data Field Returned in the Response Message:

The data field of the response message SHALL NOT be present.

Processing State Returned in the Response Message:

As defined in GlobalPlatform Card Specification [6] section 11.11.3.2, with the following addition:

’69 E1’: POL1 of the Profile Disabled by the activation of the Fall-Back Mechanism prevents this action.

4.1.1.8 ISD-R Key Set Establishment

Function name: EstablishISDRKeySet

Related Procedures: SM-SR Change

Function group: eUICC Management

Function Provider entity: ISD-R

Description: This function is used to perform mutual authentication between the new SM- SR and the eUICC and to establish a shared secret key set between the new SM-SR and the ISD-R.

This function is based on Scenario 3 as defined in “GlobalPlatform Card Specification Amendment E [11]. Scenario 3 is modified by adding the additional step of authentication of the new SM-SR to the eUICC.

Adding this step to Scenario 3 requires an additional STORE DATA command to precede the command defined for Scenario 3. This new command provides the eUICC with the certificate of the new SM-SR and retrieves a random challenge from the eUICC. This random challenge then has to be signed by the new SM-SR and sent to the eUICC in the second command to prove to the eUICC that the new SM-SR is in possession of the private key related to the certificate presented. The sequence is pictured in Figure 23 of section 3.8.

Parameters:

 Ephemeral public key of the new SM-SR  Certificate for the new SM-SR Prerequisites:

 The ECASD certificate was provided to and verified by the new SM-SR  The new SM-SR has generated an ephemeral key pair  The new SM-SR has a signature from the CI. Command Description:

This function is realised through GlobalPlatform STORE DATA commands as defined in GlobalPlatform Card Specification [6].

First STORE DATA command

Command Message

The STORE DATA command message SHALL be coded according to the following table:

Code Value                                  Meaning
CLA    ‘80’ – ‘8F’, ‘C0’ – ‘CF’ or ‘E0’ – ‘EF’ See section 11.1.4 of GlobalPlatform Card Specification [6]
INS    ‘E2’                                 STORE DATA
P1     ‘09’                                 Reference control parameter P1
Code Value                                               Meaning
P2       ‘00’                                            Block number
Lc       ‘xx’                                            Length of data field
Data     ‘xxxxx…’                                        Application data and MAC (if present)
Le         ‘00’

Table 37: STORE DATA Command Message

Reference Control Parameter P1

b8    b7    b6         b5     b4     b3     b2         b1   Meaning
0     -     -          -      -      -      -          -    More blocks
-     0     0          -      -      -      -          -    No general encryption information or non-encrypted data
-     -     -          0      1      -      -          -    DGI format of the command data field
-     -     -          -      -                        1    Case 4 command as defined in GlobalPlatform Amendment A [54]
-     -     -          -      -      X      X          -    RFU

Table 38: STORE DATA Reference Control Parameter P1

Data Field Sent in the Command Message

DGI        Length                                                       Value Description                                         MOC
‘3A01’      Var             Certificate of off-card entity                                                                          M
Tag           Length       Value Description                                                           MOC
‘7F21’        Var.         Certificate                                                                  M
Tag           Length                      Value Description                 MOC
‘93’          1-16        Certificate Serial Number                          M
‘42’          1-16        CA Identifier                                      M
‘5F20’        1-16        Subject Identifier                                 M
‘95’          1           Key Usage, Signature Verification                  M
‘5F25’        4           Effective Date (YYYYMMDD, BCD format)              O
‘5F24’        4           Expiration Date (YYYYMMDD, BCD format)             M
‘73’          3-127       Discretionary Data                                 M
                           Tag        Length     Value Description
                           'C8'       1          ‘02’, denoting an SM-
                                                 SR certificate
                           ‘C9’       20         Authority           key
                                                 identifier (value of the
                                                 Subject Key Identifier
                                                 extension of the Root
                                                 certificate)

other TLVs MAY be present

‘7F49’        Var.        Public Key – details see tables below              M
‘5F37’        Var.        Signature                                          M

Table 39: Data Fields for Send SM -SR Certificate for ISD-R Key Establishment

The following TLV-encoded data are signed off-card with SK.CI.ECDSA to generate the content of tag ‘5F37’ (signature), as described in GlobalPlatform Card Specification Amendment E [11]:

Tag      Length     Value Description                                            MOC
‘93’     1-16       Certificate Serial Number                                     M
‘42’     1-16       CA Identifier                                                 M
‘5F20’   1-16       Subject Identifier                                            M
‘95’     1          Key Usage, Signature Verification                             M
‘5F25’   4          Effective Date (YYYYMMDD, BCD format) – if present             C
‘5F24’   4          Expiration Date (YYYYMMDD, BCD format)                        M
‘73’     3-127      Discretionary Data                                            M
‘7F49’   Var.       Public Key                                                    M

Table 40: Data Signed to Generate the SM-SR Certificate

Key format is defined in section 4.1.1.5.

Response Message

Data Field Returned in the Response Message:

The STORE DATA response SHALL contain the following data:

Tag    Length      Data Element
'85'   Variable    Random Challenge

Table 41: Response Data for Send SM -SR Certificate

Processing State Returned in the Response Message:

As defined in GlobalPlatform Card Specification [6] section 11.11.3.2.

Second STORE DATA commandCommand Message

The STORE DATA command message SHALL be coded according to the following table:

Code Value                                 Meaning
CLA    '80' - '8F', 'C0' - 'CF' or 'E0' - 'EF' See section 11.1.4 of GlobalPlatform Card Specification [6]
INS    'E2'                                STORE DATA
P1     '89'                                Reference control parameter P1
P2     '01'                                Block number
Lc     'xx'                                Length of data field
Data   'xxxxx…'                            Application data and MAC (if present)
Le     ‘00’

Table 42: STORE DATA Command Message

Reference Control Parameter P1

b8       b7     b6    b5     b4     b3    b2   b1        Meaning
1        -      -     -      -      -     -    -         Last block
-        0      0     -      -      -     -    -         No general encryption information or non-encrypted data
-        -      -     0      1      -     -    -         DGI format of the command data field
-        -      -     -      -      -     -    1         Case 4 command as defined in GlobalPlatform Amendment A [54]
-        -      -     -      -      X     X    -         RFU

Table 43: STORE DATA Reference Control Parameter P1

Data Field Sent in the Command Message

DGI                   Length       Value Description                                                                                MOC
'3A02'            Var              Key Establishment                                                                                    M
 Tag      Length                                     Value Description                           MOC
'A6'      Var        CRT tag (KAT)                                                                   XM
Tag      Length        Value Description                                MOC
'90'         2             Scenario identifier ‘03’ (see GlobalPlatform         M
                           Card Specification Amendment E: Security
                           Upgrade for Card Content Management [11]
                           section 4.8.1)
                           Scenario Parameters ‘0X’ (See Table 45)
'95'         '01'          Key              Usage               Qualifier       M
                            '5C' (1 secure channel base key) or
 '10'    (3   secure     channel     keys)
 (see GlobalPlatform Card Specification [6]
Table 11-17)
'96'         '01'          Key Access according to GlobalPlatform Card          O
                           Specification [6] Table 11-18
'80'         '01'          Key Type according to GlobalPlatform Card            M
                           Specification [6] Table 11-16
'81'         '01'          Key Length (in bytes)                                M
'82'         '01'          Key Identifier = '00' - '7F'                         M
'83'         '01'          Key Version Number = '01' - '7F'                     M
'91'         '00', '02',   Initial value of sequence counter                    M
             ‘03’, '05'
             or '08'
'45'         1-n           Security Domain Image Number (SDIN)                  O
'84'         1-n           HostID (SHALL only be present if scenario            C
                           parameter b3 is set)
'7F49'            Var              ePK.SR.ECKA                                                                                          M
'5F37'            Var.             Signature                                                                                            M

Table 44: Data Field for Key Establishment

b8            b7               b6           b5          b4               b3         b2         b1         Description
–             –                –            –           –                –          –          1          Do not delete existing keys
(as defined in GlobalPlatform Card
Specification Amendment E: Security
Upgrade for Card Content
Management [11] section 4.8.1)
In the context of the ISD-R keyset
establishment process, this option
SHALL alw ays be used by the SM-
SR (see NOTE 1).
Include DR in key derivation process
                                                                                   (as defined in GlobalPlatform Card
–        –         –           –          –           –            X      –
                                                                                   Specification Amendment E: Security
                                                                                   Upgrade for Card Content
                                                                                   Management [11] section 4.8.1)
                                                                                   Include Host and Card ID in key
                                                                                   derivation process
–        –         –           –          –           X            –      –        (as defined in GlobalPlatform Card
                                                                                   Specification Amendment E: Security
                                                                                   Upgrade for Card Content
                                                                                   Management [11] section 4.8.1)
–        –         –           –          1           –            –      –        Certificate Verification precedes Key
                                                                                   Establishment
X        X         X           X          –           –            –      –        RFU

Table 45: Scenario Parameters

NOTE 1:Deletion of other keysets, belonging to the former SM-SR, can be realized by the new SM-SR using the dedicated command “FinaliseISDRhandover” defined in section 4.1.1.9, only after it has received confirmation of the proper completion of ISD-R keyset establishment.

In case the scenario parameter specifies usage of HostID+CardID (bit b3=1), then the SM- SR and the eUICC SHALL use the SIN-LV and SDIN-LV of ISD-R, in lieu of the IIN-LV and CIN-LV of the card; this deviates from GP Amendment E [11].

The SM-SR knows the SIN and SDIN of ISD-R as per the EIS.

The following TLV-encoded data are signed off-card with SK.SR. ECDSA to generate the content of DGI '5F37' (signature), as described in GlobalPlatform Card Specification Amendment E [11]:

DGI      Length   Value Description                                                                         MOC
'3A02'   Var      Key set Establishment                                                                       M
Tag    Length                               Value Description                            MOC
'A6'   Var          CRT tag (KAT)                                                           M
Tag             Length       Value Description                    MOC
DGI      Length   Value Description                                                                              MOC
                                      '90'            2                  Scenario     identifier ‘03’ (see        M
                                                                         GlobalPlatform Card Specification
                                                                         Amendment E: Security Upgrade for
                                                                         Card Content Management [11]
                                                                         section 4.8.1)
Scenario Parameters ‘0X’ (See Table
45)
'95'            '01'               Key          Usage         Qualifier     M
                                    '5C' (1 secure channel base key) or
 '10' (3 secure channel keys)
 (see       GlobalPlatform     Card
Specification [6] Table 11-17)
'96'            '01'               Key    Access       according      to    C
                                   GlobalPlatform Card Specification [6]
                                   Table 11-18– if present
'80'            '01'               Key     Type      according        to    M
                                   GlobalPlatform Card Specification [6]
                                   Table 11-16
'81'            '01'               Key Length (in bytes)                    M
'82'            '01'               Key Identifier = '00' - '7F'             M
'83'            '01'               Key Version Number = '01' - '7F'         M
'91'            '00', '02', '05'   Initial value of sequence counter        M
                or '08'
'45'            1-n                Security Domain Image Number             C
                                   (SDIN) – if present
'84'            1-n                HostID (SHALL only be present if         C
                                   scenario parameter b3 is set)
'7F49'   Var      ePK.SR.ECKA                                                                                     M
'0085'   Var      Random Challenge                                                                                M

Table 46: Data Signed to Generate the Signature

Response Message

Data Field Returned in the Response Message:

The STORE DATA response SHALL contain the following data:

Tag    Length          Data Element    MOC
‘85’   Variable        DR                C
‘86’   Variable        receipt          M

Table 47: Response Data for Scenario #3

Processing State Returned in the Response Message:

As defined in GlobalPlatform Card Specification [6]

4.1.1.9 Finalisation of the ISD-R Handover

Function name: FinaliseISDRhandover

Related Procedures: SM-SR Change

Function group: eUICC Management

Function Provider entity: ISD-R

Description: This function deletes all keys in the ISD-R except for the key ranges indicated by the command parameter(s). It is intended as a simple clean-up mechanism for the new SM-SR after takeover to get rid of all keys of the previous SM-SR in the ISD-R.

Parameters:

 Key Ranges of keys not to be deleted. Prerequisites:

 None. Command Description:

DELETE COMMAND

This function is realised through a GlobalPlatform DELETE command as defined in GlobalPlatform Card Specification [6] with proprietary parameters. This command is sent to the ISD-R.

The DELETE command SHALL have the following parameters:

Code Value        Meaning
CLA      ‘80’     See GlobalPlatform Card Specification [6] section 11.1.4.1
INS      ‘E4’     DELETE
P1       ‘00’     See GlobalPlatform Card Specification [6] section 11.2.2.1
P2       ‘00’     See GlobalPlatform Card Specification [6] section 11.2.2.2
Lc       ‘xx’     Length of data field
Data     ‘xxxx..’ TLV coded objects: Delete [card content] Data Field (See below)
Le       ‘00’

Table 48: DELETE Command Message

The Delete [card content] Data Field SHALL contain one or two instances of following TLV:

Tag Length Value Description                                          MOC
               Range of keys NOT to be deleted.
               The 3 bytes are coded as follows:
‘F2’   3       byte 1: Key Version Number of the key range            M
               byte 2: Key Identifier of first key of the key range
               byte 3: Key Identifier of last key of the key range

Table 49: Delete [card content] Command Data Field

NOTE:Two TLVs allow for one SCP80 and one SCP81 key set to “survive” key clean-up.

Example:

‘F2 03 06 01 03 F2 03 43 01 02’ will delete all keys except those with Key Version Number – Key identifier: ‘06’ – ‘01’, ‘06’ – ‘02’, ‘06’ – ‘03’, ‘43’ – ‘01’ and ‘43’ – ‘02’.

Function flow

Upon reception of the DELETE command, the eUICC SHALL:

    Check that all keys of the key set(s) used for setting up the current secure channel
     are among the keys not to be deleted. For SCP81, this also includes the key set used
     for the push SM. If that check fails, the command is terminated without deleting any
     key.
   Delete all keys except those in the key ranges indicated in the command parameters.
Response Message

Data Field Returned in the Response Message:

The data field of the response message SHALL contain a single byte of ‘00’.

Processing State returned in the Response Message:

See GlobalPlatform Card Specification [6] section 11.2.3.2.

Specific Processing State returned in response Message:

’69 85’: Key(s) of key set used for the current secure channel is/are among the keys to be deleted.

4.1.1.10 SM-SR Addressing Parameters Update

Function name: UpdateSMSRAddressingParameters

Related Procedures: SM-SR Change, Profile Download and Installation

Function group: eUICC Management

Function Provider entity: ISD-R

Description:

This function MAY be used by the new SM-SR to update SM-SR addressing parameters on the eUICC after an SM-SR Change procedure.

This function MAY be used by the SM-SR during Profile Download and Installation procedure to add a specific TP-DA for a newly downloaded Profile.

This function MAY be used by the SM-SR outside of the Profile Download and Installation or SM-SR Change procedure in case some parameters have changed.

This function has the following parameter:

   ISD-R AID
   SM-SR addressing Parameters

NOTE:The SM-SR addressing parameters for HTTPS can be updated by the function defined in GlobalPlatform Card Specification Amendment B [8], leveraging in particular the tag A5 to update only the relevant sub-TLVs, so they are not described here.

Prerequisites

-None Function flow

Upon reception of the SM-SR addressing Parameters update command, the eUICC SHALL:

Update the SM-SR addressing Parameters of the ISD-R

Commands

This command is a STORE DATA command, as described in GlobalPlatform Card
Specification [6] section 11.11.2.
                   Code                  Value                                    Meaning
CLA                       ‘80’
INS                       ‘E2’                   STORE DATA
P1                        ‘88’                   Reference Control Parameter P1 0
P2                        ‘00’                   Block Number (Not used for Enable
Lc                        ‘XX’                   Length of data field
Data                      ‘XX’                   Application Data and MAC (if present)
Le                        Not present

Table 50: STORE DATA Command Message

Parameter P1 is coded according to the following table:

b8 b7 b6 b5 b4 b3 b2 b1 Meaning

1     -    -   -     -    -      -   -   Last block
-     0    0   -     -    -      -   -   No general encryption information or non-encrypted data
-     -    -   0     1    -      -   -   DGI format of the command data field
-     -    -   -     -    X      X   X   RFU

Table 51: STORE DATA Reference Control Parameter P1

Data Field Sent in the Command Message

DGI       Length       Value Description                                       MOC
'3A07'    Var          SM-SR Addressing Parameters                             M
Tag     Length     Value Description                    MOC
'A3'    n          SMS parameters                       C
'A4'    n          BIP parameters for CAT_TP            C
‘A5’    n          DNS parameters                       C

Table 52: SMSR Addressing Parameters Update

The SM-SR MAY use each of the Tag 'A3', 'A4' and 'A5'to create or update the complete set of addressing parameters for the corresponding protocol as defined in the tables below.

The SM-SR MAY use Tag ‘A5’ with a length of zero to erase the DNS parameters.

SMS parameters value Description coding

Tag       Length       Value Description                                                  MOC
’81’      2-12         SM-SR Platform Destination Address*                                M
‘A2’      var          Profile-specific SM-SR Platform destination Addresses                O
Tag     Length
'81'    3               ISD-P identifier: digits 15 to 20 of       M
                        PIX of ISD-P
'82'    2-12            Profile-specific SM-SR Platform            M
                        Destination Address*

This structure can contain as many TLVs with tag ‘A2’ as there are ISD-Ps.

The SM-SR is responsible to overwrite this list as it sees fit when a new ISD-P is
created or after an SM-SR change. When an ISD-P is deleted, the eUICC SHALL
remove the corresponding 'A2' TLV.

Table 53: SMS Addressing Parameters Coding

*SM-SR Platform Destination Address is coded as specified for the TP-Destination-Address in 3GPP TS 23.040 [39].

BIP open channel parameters for CAT_TP link
                                                          Description

UICC/terminal interface transport level *

Data Destination Address comprehension TLV **

Table 54: BIP Open Channel Parameters for CAT_TP Link

*As defined in ETSI TS 102 226 [5] in the section “Data for CAT_TP link establishment” and “Data for BIP channel opening”.

**As defined in ETSI TS 102 223 [3].

The CR bit of the tags SHALL be set to zero.

DNS parameters
 Tag    Length     Value Description                                                                                 MOC
                  SM-SR FQDN                                                                                         M
’81’   1-n        Full Qualified Domain Name of the SM-SR that will be used in the DNS query.
                  This parameter is coded in ASCII
‘A2’   0-n        DNS serv ers List                                                                                  M
                  List of couple IP/ports allowing to reach DNS servers
Tag                           Length
‘3E' or ‘BE’                  1-n               IP address coded as an “Other Address” as          M
                                                specified by ETSI TS 102 223 [3]
'82'                          2                 Port number (integer)                              M
A3     0-n        Proprietary parameters                                                                             C
                  Additional parameters that MAY be supported by the eUICC implementation

This structure can contain more than one TLVs with tag ‘A2’ to provide more than one IP/port couples.

If the SM-SR uses Tag ‘A5’ with a length of zero then neither of the fields above are required to be present.

Table 55: DNS Parameters

The values of the profile-specific connectivity parameters, used by the eUICC to open the BIP channel to communicate with the DNS Resolver Server, are those defined in the HTTPS Connectivity Parameters of the currently Enabled ISD-P defined in Table 95.

If the SM-SR does not support a DNS Resolver Server, then it SHALL set the IP address in the HTTPS Connectivity Parameters of the ISD-R as defined in GlobalPlatform Card Specification Amendment B [8].

Response Message

Data Field Returned in the Response Message:

The data field of the response message SHALL NOT be present.

Processing State returned in the Response Message:

See GlobalPlatform Card Specification [6] section 11.11.2.

4.1.1.11 Handle Default Notification

Function name: HandleDefaultNotification

Related Procedures: Profile Enabling, Profile Enabling via SM-DP, Profile Disabling, Fall- Back Activation Procedure

Function group: eUICC Management

Function Provider entity: ISD-R

Description: This function provides a default notification from the eUICC to the SM-SR.

Parameters:

    EID
    ISD-P AID
    Mobile Equipment Identification (for example MEID, IMEI)
    Notification Sequence number
    Notification type

Prerequisites:

The eUICC has received a notification of network attachment.

Note: There is no single method implemented by all devices to notify the eUICC of
network attachment. The eUICC MAY rely on various heuristics to determine that
network attachment is effective. As a worst-case safeguard, the eUICC SHALL
attempt to send profile change notifications within a time interval of 10 STATUS
events after card reset.

Notification Message

The eUICC notification is composed of a single BER-TLV tag including several COMPREHENSION-TLV data objects; the COMPREHENSION-TLV format is defined in ETSI TS 102 223 [3].

       Description             Length                              Value                                MOC
                               (bytes)
eUICC notification tag           1       ‘E1’. To avoid conflicts with the values defined in ETSI TS      M
                                         101 220 [2], a tag from the proprietary class is used.
Length (A+B+C+D+E+F)           1 or 2    BER-TLV coding length                                            M
EID                              A       See below                                                        M
Notification type                B       See below                                                        M
Notification        sequence     C       See below                                                        M
number
ISD-P- AID                       D       See ETSI TS 102 223 [3], clause 8.60                             M
IMEI                             E       See ETSI TS 102 223 [3], clause 8.20                             C
MEID                             F       See ETSI TS 102 223 [3], clause 8.81                             C

Table 56: Data Format for Notification

IMEI and MEID are optional. In case the eUICC encounters any issue while getting the Mobile Equipment Identification of the Device, no value is provided. If both IMEI and MEID are retrieved, only one could be sent to limit overall message length.

COMPREHENSION-TLV for EID

Byte(s)                                      Description                    Length
   1          EID tag, ‘4C’.                                                  1
2          Length (X) of the EID (SHALL NOT exceed 16 bytes)               1
3 to X+2      EID value, as defined in section 2.2.2.                         X

Table 57: COMPREHENSION-TLV for EID

COMPREHENSION-TLV for Notification type

Byte(s)                                      Description                    Length
   1          Notification type tag, ‘4D’.                                    1
2          Length= ‘01’                                                    1
3          Notification type                                               1

Table 58: COMPREHENSION-TLV for Notification type

Notification type:

Coding:

    ‘01’: eUICC declaration – First network attachment
    ‘02’: Profile change succeeded
    ‘03’: Profile change failed and Roll-back
    ‘04’: Void
    ‘05’: Profile change after activation of the Fall-Back Mechanism
    ‘06’: Profile change after Emergency Profile disabling
    ‘07’: Profile change after Test Profile disabling
    ‘08’ to ‘FF’: RFU

NOTE:In case the Notification type is ‘05’, the SM-SR can inspect the ISD-P AID present in the notification message to determine whether it indicates the ISD-P AID of the Profile with the Fall-Back Attribute (denoting that this profile has been enabled after the previously enabled profile has lost connectivity) or another ISD-P AID (denoting that the previously enabled profile has been enabled again after the network connectivity has been restored).

COMPREHENSION-TLV for Notification sequence number

Byte(s)                                      Description                    Length
   1          Notification sequence number tag, ‘4E’.                         1
2          Length=’02’                                                     1
3 to 4       Notification sequence number value                              2

Table 59: COMPREHENSION-TLV for Notification Sequence Number

The notification sequence number identifies the notification message, and allows the SM-SR to distinguish a new notification from a retry. In case of a retry, the eUICC SHALL use the same notification sequence number. When a Notification Confirmation has b een successfully

received by the SM-SR, the eUICC SHALL increment the sequence number for the next notification.

NOTE:Depending on the eUICC implementation, the notification MAY also contain additional TLVs using EUM-specific tags. An SM-SR is not required to record or process such specific tags, and can simply ignore them

In any case, the size of the complete notification SHALL fit into one SMS-MO if the notification is sent by SMS, and SHALL NOT exceed the size of 240 bytes if sent by HTTP or CAT-TP.

Secured data structure for eUICC notification over SCP80

The secured data containing the eUICC notification is the COMPREHENSION-TLV structure specified above, with no added layer of Expanded format. This deviates from the requirement described in section 2.4.3.3.

Default Notification Protocol Priority

A protocol priority order for default notification MAY be defined for eve ry Profile during profile installation or download, and updated using the functions defined in 4.1.2.2 and 4.1.3.4. This protocol priority order specifies which protocols to use, and in which order, among SMS, HTTPS and CAT_TP.

If not defined for a Profile, the default priority order is set as follow:

Priorit   Protocol
   y
1       SMS
2       HTTPS
3       CAT_TP

Table 60: Default Notification Protocol Priority

4.1.1.12 Notification Confirmation

Function name: HandleNotificationConfirmation

Related Procedures: Handle Default Notification

Function group: eUICC Management

Function Provider entity: ISD-R

Description: This function confirms the notification and triggers potential follow-up activities required by POL1.

Parameters:

 Notification Sequence number Prerequisites:

 The SM-SR has received a notification from the eUICC. Function flow

Upon reception of the STORE DATA command, the eUICC SHALL:

   Disable the retry mechanism for the notification
   Perform the follow-up activities required by POL1 upon the activity that triggered the
    original notification
   Return the result of any such activity in the response data

Command Description:

STORE DATA Command

This function is realised through the GlobalPlatform STORE DATA command as defined in GlobalPlatform Card Specification [6].

Command Message

The STORE DATA command message SHALL be coded according to the following table:

Code Value                                            Meaning
CLA        ‘80’ – ‘8F’, ‘C0’ – ‘CF’ or ‘E0’ – ‘EF’ See section 11.1.4 of GlobalPlatform Card Specification [6]
INS        ‘E2’                                       STORE DATA
P1         ‘89’                                       Reference control parameter P1
P2         ‘00’                                       Block number
Lc         ‘xx’                                       Length of data field
Data       ‘xxxxx…’                                   Application data and MAC (if present)
Le         ‘00’

Table 61: STORE DATA Command Message

Reference Control Parameter P1

b8    b7         b6     b5    b4    b3    b2    b1    Meaning
1     -          -      -     -     -     -     -     Last block
-     0          0      -     -     -     -     -     No general encryption information or non-encrypted data
-     -          -      0     1     -     -     -     DGI format of the command data field
-     -          -      -     -     -     -     1     Case 4 command
-     -          -      -     -     X     X     -     RFU

Table 62: STORE DATA Reference Control Parameter P1

Data Field Sent in the Command Message

 DGI     Length                    Value Description                    MOC
‘3A08’   Var        Notification Confirmation                           M
Tag    Length             Value Description         MOC
‘4E’   2           Notification Sequence number     M

Table 63: Notification Confirmation Data Field

Response Message

Data Field Returned in the Response Message:

The data field of the response message SHALL contain the data structure below.

     Not be present, if no follow-up activities had to be performed, or
     Contain the data structure below if follow-up activities were performed.
Tag             Length                                  Value Description                         MOC
‘80’         Var                List of Deleted ISD-Ps                                                 M
Tag            Length                  Value Description          MOC
‘4F’         16                 AID of ISD-P                           M

Table 64: Notification Confirmation Response Data Field

NOTE:In the current version, the response will carry only one AID. However, the structure is defined in a generic way so that results of other follow-up activities can be added when required.

NOTE:If no follow-up activity has been performed at all, the data field SHALL contain tag 80 followed by a length of zero, and no value.

Processing State Returned in the Response Message:

As defined in GlobalPlatform Card Specification [6] section 11.11.3.2.

4.1.1.13 Set Emergency Profile Attribute

Function name: SetEmergencyProfileAttribute

Related Procedures: -

Function group: Platform Management

Function Provider entity: ISD-R

Description: This optional function sets the Emergency Profile Attribute for one Profile on the target eUICC.

Parameters:

 ISD-P-AID Prerequisites:

     The target profile SHALL NOT be enabled.
     The target Profile SHALL NOT have the Fall-Back Attribute set.

Function flow

Upon reception of the STORE DATA command, the eUICC SHALL:

      Verify that the target Profile has not the Fall-Back Attribute set.
      Set the Emergency Profile Attribute for the target Profile
      Remove the Emergency Profile Attribute from the Profile that has the attribute
       currently set.

Command Description:

STORE DATA Command

This function is realised through the GlobalPlatform STORE DATA command as defined in GlobalPlatform Card Specification [6].

Command Message

The STORE DATA command message SHALL be coded according to the following table:

Code Value                                           Meaning
CLA        ‘80’ – ‘8F’, ‘C0’ – ‘CF’ or ‘E0’ – ‘EF’ See section 11.1.4 of GlobalPlatform Card Specification [6]
INS        ‘E2’                                      STORE DATA
P1         ‘88’                                      Reference control parameter P1
P2         ‘00’                                      Block number
Lc         ‘xx’                                      Length of data field
Data       ‘xxxxx…’                                  Application data and MAC (if present)
Le                                                   Not present

Table 41113-A: STORE DATA Command Message

Reference Control Parameter P1

b8     b7         b6    b5   b4     b3   b2     b1    Meaning
1      -          -     -    -      -    -      -     Last block
-      0          0     -    -      -    -      -     No general encryption information or non-encrypted data
-      -          -     0    1      -    -      -     DGI format of the command data field
-      -          -     -    -      X    X      X     RFU

Table 41113-B: STORE DATA Reference Control Parameter P1

Data Field Sent in the Command Message

DGI                Length                                     Value Description                                 MOC
‘3A09’             Var                   Set Emergency Profile Attribute                                                M
Tag          Length                 Value Description                   MOC
‘4F’            5-16            ISD-P-AID                                      M

Table 41113-C: Set Emergency Profile Attribute Data Field

Response Message

Data Field Returned in the Response Message:

The data field of the response message SHALL NOT be present.

Processing State Returned in the Response Message:

As defined in GlobalPlatform Card Specification [6] section 11.11.3.2.

4.1.2 ES6 (Operator-eUICC) Interface Description

4.1.2.1 Policy Rules Update by Operator

Function name: UpdatePOL1byMNO

Related Procedures: Pol1 Update by Operator

Function group: Profile Management

Function Provider entity: MNO-SD

Description: This function is used to update POL1 on the eUICC.

This function has the following parameter:

 POL1 Prerequisites

 The Profile is enabled Function flow

Upon reception of the POL1 update command, the eUICC SHALL:

 Update POL1 of the ISD-P containing the targeted MNO-SD. Commands

INSTALL [for personalization] command

This function consists of an INSTALL [for personalization] command followed by a STORE DATA command, as described in GlobalPlatform Card Specification [6].

According to GlobalPlatform Card Specification [6], INSTALL [for personalization] command can only be used on applications Associated with a Security Domain. As an exceptio n from this rule, the eUICC SHALL allow the MNO-SD to receive this command sequence with data destined to the ISD-P.

INSTALL [for personalization] command:

Code   Value                             Meaning
CLA    ‘80’      See GlobalPlatform Card Specification section 11.1
INS    ‘E6’      INSTALL
P1     ‘20’       See GlobalPlatform Card Specification [6] section 11.5.2.1
P2      ‘00’     See GlobalPlatform Card Specification [6] section 11.5.2.2
Lc      ‘xx’     Data Field Length
Data   ‘xxxx…’    See GlobalPlatform Card Specification [6] section 11.5.2.3
Le      ‘00’

Table 65: INSTALL [for Personalization] Command Message

Reference Control Parameter P1

b8 b7 b6 b5 b4 b3 b2 b1 Meaning

0     0   1     0   0   0   0   0   For personalization

Table 66: INSTALL [for Personalization] Reference Control Parameter P1

Reference Control Parameter P2 – ISD-P State Coding

P2 is set to ‘00’: according to GlobalPlatform Card Specification [6] section 11.5, this means no information is provided.

Data Field

Name                                                 Length    Value      MOC
 Length of data                                      ’1’       ‘00’       M
Length of data                                      ’1’       ‘00’       M
Length of Application AID                            ‘1’       ‘05’ – ‘10’ M
Application AID (Reserved value for Profile’s ISD-P) ’05 – 10’ ‘xxxx’     M
Length of data                                      ’1’       ‘00’       M
Length of data                                      ’1’       ‘00’       M
Length of data                                      ’1’       ‘00’       M

Table 67: INSTALL Command Data Field

The reserved value for Profile’s ISD-P indicates that the Security Domain targeted by the INSTALL [for personalization] command is the ISD-P of the Profile containing the MNO-SD.

NOTE:This mechanism avoids the Operator having to know and keep track of the ISD-P AID assigned by the SM-SR.

Response Message

Data Field Returned in the Response Message:

A single byte of '00' SHALL be returned indicating that no additional data is present, as defined in the GlobalPlatform Card Specification [6] section 11.5.3.1.

Processing State returned in the Response Message:

See GlobalPlatform Card Specification [6] section 11.5.3.2.

Specific Processing State returned in response Message:

None STORE DATA command:

This command is a STORE DATA command, as described in GlobalPlatform Card Specification [6].

          Code                        Value                                     Meaning
                          ‘80’
CLA
INS                       ‘E2’                      STORE DATA
P1                        ‘88’                      Reference Control Parameter P1 0
P2                        ‘00’                      Block Number (Not used for Enable
                          ‘XX’                      Length of data field
Lc
Data                      ‘XX’                      Application Data and MAC (if present)
                          Not present
Le

Table 68: STORE DATA Command Message

Parameter P1 is coded according to the following table:
             b8 b7 b6 b5 b4 b3 b2 b1                                               Meaning
             1     -    -     -   -     -      -      -    Last block
-     0    0     -   -     -      -      -    No general encryption information or non-encrypted data
-     -    -     0   1     -      -      -    DGI format of the command data field
-     -    -     -   -     X      X      X    RFU

Table 69: STORE DATA Reference Control Parameter P1

Data Field Sent in the Command Message

      DGI                   Length                                         Value Description                                MOC
'3A06'                Var                    POL1 Policy Rules                                                               M
Tag                 Length               Value Description               MOC
'81'                 '01'                     New POL1                    M

Table 70: POL1 Update Data Field

POL1 coding

     b8        b7       b6        b5       b4       b3       b2       b1    Meaning
-          -        -         -        -        0        0        0        No POL1
                                                                           rule active
-          -        -         -        -        0        -        1        Disabling of
                                                                           this Profile
                                                                           not allowed
-          -        -         -        -        0        1        -        Deletion of
                                                                           this Profile
                                                                           not allowed
-          -        -         -        -        1        0        0        Profile
                                                                           deletion is
                                                                           mandatory
                                                                           when its
                                                                           state is
                                                                           changed to
                                                                           disabled
-          -        -         -        -        X        X        X        Other
                                                                           combinations
                                                                           are forbidden
X          X        X         X        X        -        -        -        RFU

Table 71: POL1 Coding

Response Message

Data Field Returned in the Response Message:

The data field of the response message SHALL NOT be present. Processing State returned in the Response Message:

See GlobalPlatform Card Specification [6] section 11.11.3.2

4.1.2.2 Connectivity Parameters Update by Operator

Function name: UpdateConnectivityParametersByMNO

Related Procedures: Connectivity Parameters Update by Operator

Function group: Profile Management

Function Provider entity: MNO-SD

Description: This function is used to update Connectivity Parameters on the eUICC.

This function has the following parameter:

 Connectivity Parameters Prerequisites

 The Profile is enabled Function flow

Upon reception of the Connectivity Parameters update command, the eUICC SHALL:

      Update the Connectivity Parameters of the ISD-P containing the targeted MNO-SD.

Commands

This function consists of an INSTALL [for personalization] command followed by a STORE DATA command, as described in GlobalPlatform Card Specification [6].

According to GlobalPlatform Card Specification [6], INSTALL [for personalization] command can only be used on applications Associated with a Security Domain. As an exception from this rule, the eUICC SHALL allow the MNO-SD to receive this command sequence with data destined to the ISD-P.

INSTALL [for personalization] command:

As defined in section 4.1.2.1.

STORE DATA command:

As defined in section 4.1.3.4.

4.1.3 ES8 (SM-DP-eUICC) Interface Description

4.1.3.1 ISD-P Key Set Establishment

Function name: EstablishISDPKeySet

Related Procedures: Key Establishment

Function group: Profile Management

Function Provider entity: ISD-P

Description: This function is used to perform mutual authentication between the SM-DP and the eUICC and to establish a shared secret key set between the SM-DP and the ISD-P.

This function is based on Scenario 3 as defined in GlobalPlatform Card Specification Amendment E [11]. Scenario 3 is modified by adding the additional step of authentication of the SM-DP to the eUICC.

Adding this step to Scenario 3 requires an additional STORE DATA command to precede the command defined for Scenario 3. This new command provides the eUICC with the certificate of the SM-DP and retrieves a random challenge from the eUICC. This random challenge then has to be signed by the SM-DP and sent to the eUICC in the second command to prove to the eUICC that the SM-DP is in possession of the private key related to the certificate presented. The sequence is pictured in Figure 12 of section 3.1.2.

NOTE:A complementary scenario based on RSA is FFS.

NOTE:Although the Function Provider entity is denoted as being the ISD-P, the APDUs that transport this function are executed by the ISD-R. The ISD-R will forward the appropriate content to the ISD-P

Parameters:

      ISD-P AID

 Ephemeral public key of the SM-DP  Certificate for the SM-DP Prerequisites:

 The ECASD certificate was provided to and verified by the SM-DP  SM-DP has generated an ephemeral key pair  SM-DP has a signature from the CI  ISD-P was created Command Description:

This function is realized through GlobalPlatform INSTALL [for personalization] and STORE DATA commands as defined in GlobalPlatform Card Specification [6].

INSTALL [for personalization] command

Command Message

Code Value         Meaning
CLA    ‘80’        See GlobalPlatform Card Specification section 11.1
INS    ‘E6’           INSTALL
P1     ‘20’           See GlobalPlatform Card Specification [8] section 11.5.2.1
P2      ‘00’         See GlobalPlatform Card Specification [8] section 11.5.2.2
Lc      ‘xx’         Data Field Length
Data   ‘xxxx…’ See GlobalPlatform Card Specification [8] section 11.5.2.3.6
Le      ‘00’

Table 72: INSTALL [for Personalization] Command Message

Reference Control Parameter P1
                            b8 b7 b6 b5 b4 b3 b2 b1 Meaning
0       0     1   0    0   0    0     0   For personalization

Table 73: INSTALL [for personalization] Reference Control Parameter P1

Reference Control Parameter P2 – ISD-P State Coding

P2 is set to ‘00’: according to GlobalPlatform Card Specification [8] section 11.5, this means no information is provided.

Data Field

           Name              Length      Value     MOC
Length of data              ’1’         ‘00’       M
Length of data              ’1’         ‘00’       M
Length of Application AID ‘1’           ‘05’ – ‘10’ M
Application AID of ISD-P    ’05 – 10’ ‘xxxx’       M
Length of data              ’1’         ‘00’       M
         Name              Length     Value     MOC
Length of data             ’1’      ‘00’        M
Length of data             ’1’      ‘00’        M

Table 74: INSTALL Command Data Field

Response Message

Data Field Returned in the Response Message:

A single byte of '00' SHALL be returned indicating that no additional data is present as defined in the GlobalPlatform [6] section 11.5.3.1.

Processing State returned in the Response Message:

See GlobalPlatform Card Specification [8] section 11.5.3.2.

Specific Processing State returned in response Message:

None

First STORE DATA command

Command Message

The STORE DATA command message SHALL be coded according to the following table:

Code Value                                       Meaning
CLA    ‘80’ – ‘8F’, ‘C0’ – ‘CF’ or ‘E0’ – ‘EF’ See section 11.1.4 of GlobalPlatform Card Specification [6]
INS    ‘E2’                                      STORE DATA
P1     ‘09’                                      Reference control parameter P1
P2     ‘00’                                      Block number
Lc     ‘xx’                                      Length of data field
Data   ‘xxxxx…’                                  Application data and MAC (if present)
Le         ‘00’

Table 75: STORE DATA Command Message

Reference Control Parameter P1

b8    b7    b6         b5   b4    b3   b2    b1     Meaning
0     -     -          -    -     -    -     -      More blocks
-     0     0          -    -     -    -     -      No general encryption information or non-encrypted data
-     -     -          0    1     -    -     -      DGI format of the command data field
-     -     -          -    -     -    -     1      Case 4 command as defined in GlobalPlatform Amendment A [54]
-     -     -          -    -     X    X     -      RFU

Table 76: STORE DATA Reference Control Parameter P

Data Field Sent in the Command Message

DGI        Length                                               Value Description                                       MOC
‘3A01’   Var     Certificate of off-card entity                                                                      M
 Tag            Length                                  Value Description                          MOC
‘7F21’       Var.                Certificate                                                        M
  Tag         Length              Value Description               MOC
‘93’          1-16       Certificate Serial Number                 M
‘42’          1-16       CA Identifier                             M
‘5F20’        1-16       Subject Identifier                        M
‘95’          1          Key Usage, Signature Verification         M
‘5F25’        4          Effective Date (YYYYMMDD, BCD             O
                         format)
‘5F24’        4          Expiration Date (YYYYMMDD, BCD            M
                         format)
‘73’          3-127      Discretionary Data                        M
                          Tag    Length       Value
                                              Description
                          'C8'   1            ‘01’, denoting
                                              an      SM-DP
                                              certificate
                          ‘C9’   20           Authority key
                                              identifier
                                              (value of the
                                              Subject Key
                                              Identifier
                                              extension of
                                              the        Root
                                              certificate)

other TLVs MAY be present

‘7F49’        Var.       Public Key – details see tables below     M
‘5F37’        Var.       Signature                                 M

Table 77: Data Fields for Send SM -DP Certificate for ISD-P Key Establishment

The following TLV-encoded data are signed off-card with SK.CI. ECDSA to generate the content of tag ‘5F37’ (signature), as described in GlobalPlatform Card Specification Amendment E [11]:

Tag       Length     Value Description                                               MOC
‘93’      1-16       Certificate Serial Number                                         M
‘42’      1-16       CA Identifier                                                     M
‘5F20’    1-16       Subject Identifier                                                M
‘95’      1          Key Usage, Signature Verification                                 M
‘5F25’    4          Effective Date (YYYYMMDD, BCD format) – if present                C
‘5F24’    4          Expiration Date (YYYYMMDD, BCD format)                            M
‘73’      3-127      Discretionary Data                                                M
‘7F49’    Var.       Public Key                                                        M

Table 78: Data Signed to Generate the SM-DP Certificate

Key format is defined in section 4.1.1.5.

Response Message

Data Field Returned in the Response Message:

The STORE DATA response SHALL contain the following data:

Tag      Length        Data Element
'85'     Variable      Random Challenge

Table 79: Response Data for Send SM -DP Certificate

Processing State Returned in the Response Message:

As defined in GlobalPlatform Card Specification [6] section 11.11.3.2.[6]

Second STORE DATA command

Command Message

The STORE DATA command message SHALL be coded according to the following table:

Code                          Value                                              Meaning
CLA        '80' - '8F', 'C0' - 'CF' or 'E0' - 'EF' See section 11.1.4 of GlobalPlatform Card Specification [6]
INS        'E2'                                          STORE DATA
P1         '89'                                          Reference control parameter P1
P2         '01'                                          Block number
Lc         'xx'                                          Length of data field
Data       'xxxxx…'                                      Application data and MAC (if present)
Le         ‘00’

Table 80: STORE DATA Command Message

Reference Control Parameter P1
       b8   b7     b6         b5     b4     b3    b2      b1        Meaning
1    -      -          -      -      -     -       -         Last block
-    0      0          -      -      -     -       -         No general encryption information or non-encrypted data
-    -      -          0      1      -     -       -         DGI format of the command data field
-    -      -          -      -      -     -       1         Case 4 command as defined in GlobalPlatform Amendment A [54]
-    -      -          -      -      X     X       -         RFU

Table 81: STORE DATA Reference Control Parameter

Data Field Sent in the Command Message

  DGI          Length                                                     Value Description                                   MOC
'3A02'     Var                   Key set Establish                                                                                M
 Tag      Length                                   Value Description                         MOC
'A6'      Var           CRT tag (KAT)                                                            XM
Tag      Length                  Value Description               MOC
DGI     Length                                         Value Description                                             MOC
                                     '90'       2             Scenario identifier ‘03’ (see GlobalPlatform             M
                                                              Card Specification Amendment E: Security
                                                              Upgrade for Card Content Management [11]
                                                              section 4.8.1)
                                                              Scenario Parameters ‘0X’ (See Table 83)
'95'       '01'          Key              Usage               Qualifier           M
                          '5C' (1 secure channel base key) or
 '10'    (3   secure     channel     keys)
 (see GlobalPlatform Card Specification [6]
Table 11-17)
'96'       '01'          Key Access according to GlobalPlatform Card              O
                         Specification [[6] Table 11-18
'80'       '01'          Key Type according to GlobalPlatform Card                M
                         Specification [6] Table 11-16
'81'       '01'          Key Length (in bytes)                                    M
'82'       '01'          Key Identifier = '00' - '7F'                             M
'83'       '01'          Key Version Number = '01' - '7F'                         M
'91'       '00', '02',   Initial value of sequence counter                        M
           '05' or
           '08'
'45'       1-n           Security Domain Image Number (SDIN)                      O
'84'       1-n           HostID (SHALL only be present if scenario                C
                         parameter b3 is set)
'7F49'   Var       ePK.DP.ECKA                                                                                           M
'5F37'   Var.      Signature                                                                                             M

Table 82: Send SM -DP Certificate Data Field

The following TLV-encoded data are signed off-card with SK.DP. ECDSA to generate the content of DGI '5F37' (signature), as described in GlobalPlatform Card Specification Amendment E [11]:

b8      b7        b6          b5         b4             b3        b2         b1                           Description
 0       0        0           0              –          X          X          X       As defined in GlobalPlatform Card Specification
                                                                                         Amendment E: Security Upgrade for Card
                                                                                          Content Management [11] section 4.8.1
-      -        -           -              1          –          –          –               Certificate Verification precedes Key
                                                                                                       Establishment

Table 83: Scenario Parameters

In case the scenario parameter specifies usage of HostID+CardID (bit b3=1), then the SM- DP and the eUICC SHALL use the SIN-LV and SDIN-LV of ISD-R, in lieu of the IIN-LV and CIN-LV of the card; this deviates from GP Amendment E [11], and ISD-P has no SIN/SDIN yet.

The SM-DP can know the SIN and SDIN of ISD-R by inspecting the EIS retrieved on ES3.

 DGI     Length                                         Value Description                                              MOC
'3A02'   Var      Key set Establishment                                                                                M
Tag      Length                                  Value Description                                   MOC
'A6'     Var        CRT tag (KAT)                                                                    M
Tag                 Length             Value Description                 MOC
'90'                2                          Scenario identifier ‘03’ (see     M
                                               GlobalPlatform           Card
                                               Specification Amendment E:
                                               Security Upgrade for Card
                                               Content Management        [11]
                                               section 4.8.1)
Scenario Parameters ‘0X’ (See
Table 83)
'95'                '01'                       Key        Usage     Qualifier    M
                                                 '5C' (1 secure channel base
                                               key) or
                                                '10' (3 secure channel keys)
                                                (see GlobalPlatform Card
                                               Specification [6] Table 11-17)
'96'                '01'                       Key Access according to            C
                                               GlobalPlatform            Card
                                               Specification [6] Table 11-18 –
                                               if present
'80'                '01'                       Key Type according to             M
                                               GlobalPlatform            Card
                                               Specification [6] Table 11-16
'81'                '01'                       Key Length (in bytes)             M
'82'                '01'                       Key Identifier = '00' - '7F'      M
'83'                '01'                       Key Version Number = '01' -       M
                                               '7F'
'91'                '00', '02', '05' or '08'   Initial value     of   sequence   M
                                               counter
'45'                1-n                        Security  Domain       Image       C
                                               Number (SDIN) – if present
'84'                1-n                        HostID (SHALL only be              C
                                               present if scenario parameter
                                               b3 is set)
'7F49'   Var      ePK.DP.ECKA                                                                                          M
'0085'   Var      Random Challenge                                                                                     M

Table 84: Data Signed to Generate the Signature

Response Message

Data Field Returned in the Response Message:

The STORE DATA response SHALL contain the following data:

Tag      Length     Value Description        MOC
'85'     Variable   DR                           C
'86'     Variable   Receipt                      M

Table 85: Response Data for Scenario #3

Processing State Returned in the Response Message:

As defined in GlobalPlatform Card Specification [6] section 11.11.3.2.

4.1.3.2 Command coding for SCP03

All ES8 functions in subsequent sections require securing the commands by SCP03.
   NOTE:        The profile package itself is protected by SCP03t as defined in the next
                section.

Opening an SCP03 secure channel requires the following two commands: INITIALIZE UPDATE

Code                              Value                                  Description
 CLA                    See to GlobalPlatform Card                      Section 7.1.1
                      Specification Amendment D [10]
INS                    See to GlobalPlatform Card                  INITIALIZE UPDATE
                     Specification Amendment D [10]
P1                                ‘XX’                    indicates the version of the target ISD-
                                                                      P key set used
P2                                ‘XX’                    indicates the key identifier of the target
                                                                           ISD-P
Lc                                ‘08’                         Length of the host challenge
Data                             ‘XX…XX’                        For Host Challenge see
                                                            GlobalPlatform Card Specification
                                                           Amendment D [10] for computation of
                                                                  the host challenge
Le                                ‘00’

Table 86: Initialize Update Command

EXTERNAL AUTHENTICATE

Code                              Value                                  Description
CLA                See GlobalPlatform Card Specification                Section 7.1.2.
                           Amendment D [10]
INS               See GlobalPlatform Card Specification       EXTERNAL AUTHENTICATE
                          Amendment D [10]
P1                                ‘33’                    indicates the security level and SHALL
                                                          be set to request C-DECRYPTION, R-
                                                          DECRIPTION, R-MAC and C-MAC (see
                                                          to GlobalPlatform Card Specification
                                                          Amendment D [10])
P2                                ‘00’
Lc                                ‘10’                      Length of the host cryptogram and
                                                                           MAC
Data                             ‘XX…XX’                    Host cryptogram and MAC (see to
                                                            GlobalPlatform Card Specification
                                                           Amendment D [10] for computation of
                                                               host cryptogram and MAC)
Le                                                                      Not Present

Table 87: External Authenticate Command

These two commands SHALL be following by any ES8 command as defined in subsequent sections depending on the procedure to be performed. Those ES8 commands and their responses are modified by encrypting the data part and adding a MAC as defined in GlobalPlatform Card Specification Amendment D [10].

4.1.3.3 Download and Installation of a Profile

Function name: DownloadAndInstallation Related Procedures: Profile Download and Installation Function group: Profile Management Function Provider entity: ISD-P Description: This function is used to load a Profile into an ISD-P on the eUICC. The ISD-P must be already created and also already personalized. The Profile created by the SM-DP must be compatible with the targeted eUICC.

NOTE:The ISD-P identification is provided within the ES5 transport protocol.

The Profile SHALL be protected by SCP03t. The Profile SHALL include in particular:
    The setting of POL1, if defined by Operator
    The setting of connectivity parameters (see section 4.1.3.4)
    The setting of ISD-P state from ‘CREATED’ to ‘DISABLED’ when installation is
      finished.
Parameters:

 Profile Prerequisites:

 ISD-P must be created  ISD-P must be PERSONALIZED (as defined in GlobalPlatform Card Specification[6])  Connection is secured via SCP03t Check Figure 13 for further details.

Description of the SCP03t security protocol:

This section defines a secure channel protocol based on GlobalPlatform's SCP03 usable for TLV structures, named SCP03t hereafter.

Tag values are defined so that they can be used without conflict within the expanded remote management format which is used to transport data inside SCP80 or SCP81 of ES5.

As no SWs are used, errors are indicated by a special response tag with tag number +'80' (resulting in a 2 byte tag).

The data transported in the command TLVs specified below SHALL consist of the Profile Package specified in [53]; the response TLVs SHALL transport Profile Element (PE) responses as provided by the Profile Package processing specified in SIMalliance: eUICC Profile Package - Interoperable Format Technical Specification [53].

NOTE         The SM-DP MAY support a former version v2.x of the SIMalliance: eUICC
             Profile Package - Interoperable Format Technical Specification, to download
             a profile onto an eUICC complying with a former version of this specification.
The SM-DP can inspect the EIS of the target eUICC to determine which
versions of SIMalliance eUICC Profile Package [53] are supported by the
target eUICC.

The Profile Package consists of a sequence of PE TLVs. However, SCP03t does not take that PE structure into account, but treats the whole Profile Package as one block of transparent data. That block of data is split into segments of a maximum size of 1024 bytes (including the tag and length field). The eUICC SHALL support profile command data segments of at least up to this size.

The options allowed in SCP03 are limited as follows in SCP03t:

   Response security is always the same as command security (if no error).
   BEGIN/END R-MAC SESSION is not supported.
   Only one option is defined: MAC + encryption.

The following sections describe the changes required to move from SCP03 to SCP03t. Everything else is inherited from SCP03.

As the security mechanisms are exactly the same as SCP03, the SCP03 key sets are used for SCP03t.

Secure channel initiation uses 2 TLVs equivalent to the INITIALIZE UPDATE and the EXTERNAL AUTHENTICATE APDUs.

Thereafter, the command and response TLVs are protected in the same way as SCP03 APDUs, using either:

   the SCP03t sessions keys resulting from the secure channel initiation
   or random keys which replaces session keys.

Each command TLV triggers one response TLV. A response MAY be empty or carry response data from the application layer.

In case the eUICC indicates a fatal error in a response TLV, it MAY stop sending subsequent response TLVs.

Secure Channel Initiation: INITIALIZE UPDATE command TLV

The following data SHALL be encapsulated in a TLV with tag '84':

Name                 Length   Presence
Key version number   1 byte   Mandatory
Key identifier       1 byte   Mandatory
(and value must be
‘00’, consistently with
SCP03)
Name                   Length           Presence
Host challenge         8 bytes          Mandatory

Table 88: Initialize Update Command TLV

The data field of the response TLV SHALL contain the concatenation without delimiters of the following data elements, encapsulated in a TLV with tag '84'.

Name                    Length         Presence
Key diversification data 10 bytes      Mandatory
Key information         3 bytes        Mandatory
Card challenge          8 bytes        Mandatory
Card cryptogram         8 bytes        Mandatory
Sequence Counter        3 bytes        Mandatory

Table 89: Response TLV Data Elements

In case of an error, tag '9F44' is used (see NOTE 1 below). The following values are defined:

   '01': error in length or structure of command data
   '03': referenced data not found

NOTE 1:an eUICC MAY also detect the error in length or structure of command data at the transport layer (expanded remote command format), and return a bad format TLV as defined in ETSI TS 102 226 [5] instead of the SCP03t-specific error tag.

Secure Channel Initiation: EXTERNAL AUTHENTICATE command TLV

The following data SHALL be encapsulated in a TLV with tag '85':

Name                    Length         Presence
Security level          1 byte         Mandatory
Host cryptogram         8 bytes        Mandatory
MAC                     8 bytes        Mandatory

Table 90: External Authenticate Command TLV

The security level SHALL be set to '33': "C DECRYPTION, R ENCRYPTION, C MAC, and R MAC".

The MAC SHALL be computed based on the values present in the TLV, as follows:

=L + LMAC = ‘11’

MAC chaining value (16 bytes ‘00’)   ‘85’   Lcc    Security Host cryptogram
                                                   level
C-MAC calculation as defined in section
§6.2.4 of GP Amendment D                       S-MAC
‘85’   Lcc    Security Host cryptogram                        C-MAC
              level

Figure 45: C-MAC Computation for External Authenticate Command TLV

If the message is accepted, a Response TLV with tag '85' and length zero SHALL be returned.

This TLV does not return an R-MAC.

In case of an error, tag '9F45' is used (see NOTE 1 above). The following values are defined:

   '01': error in length or structure of command data
   '02': security error

Command TLV C-MAC and C-DECRYPTION Generation and Verification

For encapsulating encrypted profile command data in a SCP03t TLV, tag '86' is used.

Command Data field – plain text – length L

Command Data field – plain text           '80'       (00..00)
ICV                 AES-CBC                      S-ENC

Lcc = L + length of padding + L MAC

MAC chaining value
                           '86'     Lcc              Ciphered Command Data field (length Lcc - 8)
   (16 bytes)
 C-MAC calculation as
defined in section 6.2.4         S-MAC
‘86'          Lcc                                Ciphered Command Data field                                C-MAC

Figure 46: TLV Command Data Field Encryption

Response R-MAC and R-ENCRYPTION Generation and Verification

For encapsulating encrypted profile response data in a SCP03t TLV, tag '86' is used.

If there is no response data field, the length is ‘00’, and no R-MAC SHALL be generated, so the response TLV SHALL be ’86 00’.In case of an error, tag '9F46' is used (see NOTE 1 above), and no R-MAC nor R-ENCRYPTION SHALL be generated. The response data field contains only one byte, the following values are defined:

   '01': error in length or structure of command data
   '02': security error

Response Data field – plain text – length L

Response Data field – plain text           '80'       (00..00)
ICV                 AES-CBC                      S-ENC

Lcc = L + length of padding + L MAC

MAC chaining value
                           '86'     Lcc              Ciphered Response Data field (length Lcc - 8)
   (16 bytes)
 R-MAC calculation as
defined in section 6.2.4         S-RMAC
‘86'          Lcc                                Ciphered Response Data field                                R-MAC

Figure 47: TLV Response Data Field Encryption

Profile protection:

Profile protection SHALL performed using either:
    Session keys (S-ENC, S-MAC, S-RMAC) resulting from the key agreement with
        eUICC (INITIALIZE UPDATE and EXTERNAL AUTHENTICATE).
    Or random keys per Profile (denoted PPK-ENC, PPK-MAC, PPK-RMAC in this
        document), generated by the SM-DP.
                                         Command 85
Command 84                                                                      Command 86
                                   (generates S-ENC,
                                    S-MAC, but they                           (S-ENC, S-MAC)
                                    are not used yet)
        Response 84                              Response 85                            Response 86
                                                                                    (S-ENC, S-RMAC)
Figure 4133-A: Key usage for the protection of the SCP03t command and
               responses when using initial session keys
                       Command 85
Command 84           (generates S-ENC,
                                               Command 87                Command 86
                      S-MAC, but they         (S-ENC, S-MAC)         (PPK-ENC, PPK-MAC)
                      are not used yet)
Response 84            Response 85             Response 87               Response 86
                                                                    (PPK-ENC, PPK-RMAC)
     Figure 4133-B: Key usage for the protection of the SCP03t command and
                      responses when using random keys
If random key mode is selected by the SM-DP, the initial MAC chaining value to be used for
the first segment of the profile protection is provided together with the random keys and the
encryption counter for ICV calculation is reset to its initial state (i.e. the value on 16 bytes is
'00…01'). Otherwise the MAC chaining method SHALL be applied (i.e. the MAC chaining value
of the previous command TLV SHALL be used).
PPK-ENC, PPK-MAC and PPK-RMAC SHALL have the same length as S-ENC, S-MAC, S-
RMAC.
It is the SM-DP choice whether to use this random keyset (PPK-ENC, PPK-MAC and PPK-
RMAC). This mode allows performing Profile Protection in advance without having any eUICC
knowledge. It may help to provide a better SM-DP scalability. The eUICC SHALL be able to
support both modes.
Session keys and, if used, the random keys SHALL only be used in the Profile download
process. They SHALL be deleted on the eUICC at the latest at the end of the process.
In case of failure during the first attempt to download a Profile, th e PPK-RMAC SHALL NOT
be reused again. The SM-DP SHALL regenerate a new PPK-RMAC for every retry.
Replace session key command TLV
This command is used, during the download of a Protected Profile, to replace the SCP03t
session keys (S-ENC, S-MAC and S-RMAC) by a new set of session keys (typically the PPK-
ENC, PPK-MAC and PPK-RMAC) protecting the command and response TLVs. Note that all
keys (S-ENC, S-MAC and S-RMAC) have to be replaced. This command doesn't allow to
replace only a part of the session keys. The response SHALL be encrypted by PPK-ENC and
MAC-ed by PPK-RMAC, where PPK-RMAC SHALL be different for each download attempt of
the same Profile.
The following data SHALL be encapsulated in a BER-TLV with tag '87':
                           Tag   Length    Value description      MOC
                           80    16        Initial MAC chaining   M
                                           value
                           81    16 - 32   PPK-ENC                M
82    16 - 32   PPK-MAC                M
83    16 - 32   PPK-RMAC               M

Table 4133-C: Replace Session Key Command TLV

When using random keys for profile protection, the Replace session key command SHALL be
sent directly before the SCP03t command TLVs containing the protected profile package (tag
86).
When using session keys for profile protection, the Replace session key command SHALL
NOT be present.
On reception of this command the eUICC SHALL:
    Verify that the new keys are of same length as the old keys. If not the eUICC SHALL
      return an error ('01'), and the loading of the Profile SHALL be aborted.
    Replace the current session keys with the new set of keys.

Once the command is successfully executed, the eUICC SHALL use this new set o f keys for decryption and MAC verification of subsequent SCP03t blocks of data, and encryption and MACing of responses. The key type of the new set of keys is the same as the session keys they replace.

If the command message is accepted, a Response TLV with tag '87' and length zero SHALL be returned. This TLV does not return an R-MAC.

In case of an error, tag '9F47' is used (see NOTE 1 above). The following values are defined:

      '01': error in length or structure of command data
      '02': security error

4.1.3.4 Connectivity Parameters Update using SCP03

Function name: UpdateConnectivityParameters SCP03

Related Procedures: Connectivity Parameters Update using SCP03

Function group: eUICC Management

Function Provider entity: ISD-P

Description: This function is used to update Connectivity Parameters on the eUICC.

This function has the following parameter:

 ISD-P AID  Connectivity Parameters Prerequisites

 None Function flow

Upon reception of the Connectivity Parameters update command, the eUICC SHALL:

 Update the Connectivity Parameters of the targeted ISD-P Commands

STORE DATA Command

This command is a STORE DATA command, as described in GlobalPlatform Card Specification [6] section 11.11.3.2.

           Code                     Value                                     Meaning
CLA                          ‘80’
INS                          ‘E2’                 STORE DATA
P1                           ‘88’                 Reference Control Parameter P1 0
P2                           ‘00’                 Block Number (Not used for Enable
Lc                           ‘XX’                 Length of data field
Data                         ‘XX’                 Application Data and MAC (if present)
Le                           Not present

Table 91: STORE DATA Command Message

Parameter P1 is coded according to the following table:

b8 b7 b6 b5 b4 b3 b2 b1 Meaning

1      -   -      -     -    -   -   -    Last block
-      0   0      -     -    -   -   -    No general encryption information or non-encrypted data
-      -   -      0     1    -   -   -    DGI format of the command data field
-      -   -      -     -    X   X   X    RFU

Table 92: STORE DATA Reference Control Parameter P1

Data Field Sent in the Command Message

  DGI         Length                                            Value Description                                     MOC
'3A07'    Var              Connectivity Parameters                                                                     M
Tag               Length                           Value Description                   MOC
'A0'              n                  Connectivity parameters for SMS protocol               C
'A1'              n                  Connectivity parameters for HTTP protocol              C
'A2'              n                  Connectivity parameters for CAT_TP protocol            C

Table 93: Connectivity Parameters Data Field

The order of protocol connectivity parameters TLVs in the DGI define the protocol priority order to send notifications defined in section 4.1.1.11. If several TLVs are provided for the same protocol, the eUICC SHALL use the first TLV for this protocol, and ignore the extra TLVs for the same protocol.

NOTE 1:Void

NOTE 2:Multiple occurrences of each Connectivity Parameters TLV are possible , if they are sent by an off-card entity following a former version of this document.

SMS parameters coding

Tag Length         Value Description MOC
06*   Variable      SMSC Address*   M
81       1              PID**      O
82       1             DCS**       O

Table 94: Coding of Connectivity Parameters for SMS Protocol

* COMPREHENSION-TLV as defined in ETSI TS 102 223 [3], with the CR bit of the tags set to zero.

** Coding on one byte as specified in 3GPP TS 23.040 [39]

If no PID TLV is present, the eUICC SHALL use a default value of PID=00.

If no DCS TLV is present, the eUICC SHALL use a default value of DCS=04.

HTTP and CAT_TP parameters coding

Description

Bearer description*

Network Access Name (NAN) *

User Login*

User Password*

Table 95: Coding of Connectivity Parameters for HTTP and CAT_TP Protocols

* Comprehension TLVs as defined in ETSI TS 102 223 [3]. The CR bit of the tags SHALL be set to zero.

Response Message

Data Field Returned in the Response Message:

The data field of the response message SHALL NOT be present.

Processing State returned in the Response Message:

See GlobalPlatform Card Specification [6] section 11.11.3.2.

4.1.4 ESx (Device - eUICC) Interface Description

The eUICC MAY support the Local Enable and Disable command for the Emergency Profile.

The eUICC MAY support the Local Enable and Disable command for the Test Profile.

4.1.4.1 Local Enable for Emergency Profile

Function name: LocalEnableEmergencyProfile

Function group: Local Management

Function Provider entity: eUICC

Description: This function is used by the Device to locally enable the Emergency Profile. The eUICC SHALL NOT send notifications to the SM-SR. The Emergency Profile SHOULD remain enabled even after a restart of the Device. It is up to the Device to disable the Emergency Profile.

Prerequisites:

     A Profile with the Emergency Profile Attribute set exists on the eUICC.
     The Profile with the Emergency Profile Attribute set is not already enabled.

Command Description:

The Local Enable and Local Disable of a Profile with the Emergency Profile Attribute set is realised by using the ENVELOPE command with a dedicated Tag.

Data Field of ENVELOPE

    Tag           Length                    Value Description                               MOC
    ‘E4’            1       00: Local Enable of Emergency Profile                           M
                            01: Local Disable of Emergency Profile
                            02: Local Enable of Test Profile
                            03: Local Disable of Test Profile
                            04-FF: RFU
Table 4141: Data Field for Envelope containing Local Enable and Local Disable

Data Field Returned in the Response Message:

The structure of the response data is defined below: -- ASN1START

ResultCode ::= [0] INTEGER{ success (0), errorProfileRef (8), -- Emergency/Test Profile does not exists errorAlreadyEnabled (9), -- Emergency/Test Profile is already enabled errorAlreadyDisabled (10), -- Emergency/Test Profile is already disabled errorForbidden (12), -- Transition is forbidden for the Test Profile undefinedError (127) }

-- ASN1STOP

The following table defines the error codes that are permitted for each command:

                                                           Response
        Command
                                        (0)          (8)      (9)         (10)         (12)
LocalEnableEmergencyProfile              X           X        X
LocalDisableEmergencyProfile                 X                                 X
                                                         Response
      Command
                                        (0)       (8)        (9)          (10)        (12)
LocalEnableTestProfile                  X          X          X                        X
LocalDisableTestProfile                  X                                  X

Table 4141: Error codes allowed for each Local command

NOTE           In order to support a legacy implementation for the Device, the eUICC MAY
               support implementation specific commands to trigger the Local Enable and
               the Local Disable of the Emergency Profile.

4.1.4.2 Local Disable for Emergency Profile

Function name: LocalDisableEmergencyProfile

Function group: Local Management

Function Provider entity: eUICC

Description: This function is used by the Device to locally disable the Emergency Profile and enable the previously enabled Profile. In case the Local Disable fails, the Fall-Back Mechanism SHALL be activated. The Fall-Back Mechanism SHALL consider that its previously enabled Profile is the Profile that was enabled before the Local Enable of the Emergency Profile. After disabling the Emergency Profile the eUICC MAY send a notification to the SM-SR (see 4.1.1.11)

Prerequisites:

      A Profile with the Emergency Profile Attribute set exists on the eUICC
      The Profile with the Emergency Profile Attribute set is enabled

Command and Response Description:

See 4.1.4.1

4.1.4.3 Local Enable for Test Profile

Function name: LocalEnableTestProfile

Function group: Local Management

Function Provider entity: eUICC

Description: This function is used by the Device to locally enable the Test Profile. The eUICC SHALL NOT send notifications to the SM-SR. The Test Profile SHOULD remain enabled even after a restart of the Device. It is up to the Device to disable the Test Profile.

Prerequisites:

      A Test Profile exists on the eUICC.
      The Test Profile is not already enabled.
      The Emergency Profile is not currently enabled.

Command and Response Description:

See 4.1.4.1

4.1.4.4 Local Disable for Test Profile

Function name: LocalDisableTestProfile

Function group: Local Management

Function Provider entity: eUICC

Description: This function is used by the Device to locally disable the Test Profile and enable the previously enabled Profile. In case the Local Disable fails, the Fall-Back Mechanism SHALL be activated. The Fall-Back Mechanism SHALL consider that its previously enabled Profile is the Profile that was enabled before the Local Enable of the Test Profile. After disabling the Test Profile the eUICC MAY send a notification to the SM-SR (see 4.1.1.11).Prerequisites:

      A Test Profile exists on the eUICC
      The Test Profile is enabled

Command and Response Description:

See 4.1.4.1

5 Off-Card Interface Descriptions

This section provides the description of the interfaces and functions within the Remote Provisioning and Management system outside the eUICC, including the following:

      ES1, interface between the two entities fulfilling the Role EUM and the Role SM-SR.
      ES2, interface between the two entities fulfilling the Role Operator and the Role SM-
       DP.
      ES3, interface between the two entities fulfilling the Role SM-DP and the Role SM-
       SR.
      ES4, interface between the two entities fulfilling the Role Operator and the Role SM-
       SR, also used between the two entities fulfilling the Role M2M SP and the Role SM-
       SR.
      ES4A, interface between the two entities fulfilling the Role Operator a nd the Role SM-
       SR, for the specific purpose of configuring M2M SP authorisations and Operator
       notifications
      ES7, interface between the two entities fulfilling the Role SM-SR and the Role SM-
       SR.

The functions in this section are grouped into function groups. Each function group is provided by a unique Role and corresponds to an autonomous and consistent functionality.

When a function group is implemented by a Role, all the functions associated to this function group SHALL be implemented by that Role. In other words, function groups cannot be partially implemented; if a special function is requested, then all the functions of the corresponding function group SHALL be implemented.

The following table presents the normative list of all the functions that are def ined in this section.

Request-response functions:

                                                                                       Function
  Interface       Function group                           Functions
                                                                                     prov ider Role
                                    RegisterEIS
ES1           eUICC Management                                                          SM-SR
                                    UpdateEISAdditionalPropertiesRequest
                                    GetEIS
                                    AuditEIS
                                    DownloadProfile
                                    SetFallBackAttribute
                                    SetEmergencyProfileAttribute
                                    UpdatePolicyRules                                   SM-DP
              Profile Management
                                    UpdateSubscriptionAddress
ES2                                 GetONC
                                    SetONC
                                    GetPLMA
                                    SetPLMA
                      EnableProfile
Platform Management   DisableProfile                                      SM-DP
                      DeleteProfile
                                    GetEIS
                                    AuditEIS
                                    CreateISDP
                                    SendData
                                    ProfileDownloadCompleted
                                    SetFallBackAttribute
                                    SetEmergencyProfileAttribute
ES3                                                                                     SM-SR
              Profile Management    UpdatePolicyRules
                                    UpdateSubscriptionAddress
                                    UpdateConnectivityParameters
                                    GetONC
                                    SetONC
                                    GetPLMA
                                    SetPLMA
                        EnableProfile
Platform Management     DisableProfile                              SM-SR
                        DeleteISDP
                                       GetEIS
                                       SetFallBackAttribute
                                       SetEmergencyProfileAttribute
                                       UpdatePolicyRules
               Profile Management                                                  SM-SR
                                       UpdateSubscriptionAddress
                                       AuditEIS
ES4
                                       GetPLMA
                        EnableProfile
Platform Management     DisableProfile                              SM-SR
                        DeleteProfile
                        PrepareSMSRChange
eUICC Management                                                    SM-SR
                        SMSRchange
                                       GetONC
                                       SetONC
ES4A           Profile Management                                                  SM-SR
                                       GetPLMA
                                       SetPLMA
                                       CreateAdditionalKeySet
ES7            eUICC Management        HandoverEUICC                               SM-SR
                                       AuthenticateSMSR

Table 96: Request-Response Functions

Notification handler functions:

                                                                                   Function
Interfa   Function                        Notification handler functions          handler/reci
  ce       group
                                                                                     pient
         HandleProfileDisabledNotification
Platform
Managem HandleProfileEnabledNotification                                 Operator
ent
         HandleProfileDeletedNotification
                      HandleEmergencyProfileAttributeSetNotification
                      HandleEmergencyProfileAttributeUnsetNotification
                   HandleProfileDownloadedNotification
ES2        Profile
           Managem HandlePLMAChangedNotification                                    Operator
           ent
                   HandlePolicyRulesUpdatedNotification
                      HandleProfileFallBackAttributeSetNotification
                      HandleProfileFallBackAttributeUnsetNotification
eUICC   HandleSMSRChangeNotification
Managem                                                                  Operator
ent
         HandleProfileDisabledNotification
Platform
Managem HandleProfileEnabledNotification                                                               SM-DP
ent
         HandleProfileDeletedNotification
                    HandleEmergencyProfileAttributeSetNotification
                    HandleEmergencyProfileAttributeUnsetNotificationHandleProfileDow
ES3                 nloadedNotification
          Profile
                                                                                                               SM-DP (see
          Managem HandlePLMAChangedNotification
                                                                                                                NOTE)
          ent
                  HandlePolicyRulesUpdatedNotification
                  HandleProfileFallBackAttributeSetNotification
          HandleProfileFallBackAttributeUnsetNotification
eUICC
Managem HandleSMSRChangeNotification                                                                   SM-DP
ent
          HandleProfileDisabledNotification
Platform HandleProfileEnabledNotification                                                            Operator or
Managem                                                                                             M2M SP (see
ent      HandleProfileDeletedNotification                                                           NOTE below)
                    HandleEmergencyProfileAttributeSetNotification
                    HandleEmergencyProfileAttributeUnsetNotification
ES4
                  HandleProfileDownloadedNotification
          Profile                                                                                             M2M SP (see
          Managem HandlePLMAChangedNotification
                                                                                                              NOTE below)
          ent
                  HandlePolicyRulesUpdatedNotification
                    HandleProfileFallBackAttributeSetNotification
                    HandleProfileFallBackAttributeUnsetNotification
          eUICC
          Managem HandleSMSRChangeNotification                                                                  Operator
          ent

Table 97: Notification Handler Functions

NOTE:the sending of notification to the M2M SP is conditional to authorisation of the M2M SP by the Operator owner of the Profile

5.1 Function Commonalities

Each functions represents an entry points that is provided by a Role (function provider), and that can be called by other Roles (function requester).

5.1.1 Common Data Types

The functions provided in this section deal with management of eUICC and Profile, so that the common data defined in this section need to be used in most of the functions.

5.1.1.1 Simple Types

Type name                                Description                                            Type definition
                       String of even length composed of characters between ‘0’ to ‘9’
Hexadecimal String
                       and ‘A’ to ‘F’ or ‘a’ to ‘f’.
                       The AID (Application IDentifier) of an Executable Load File, an   Hexadecimal string representation of 5 to 16
AID                    Executable Module, a security domain, or an Application.          bytes.
Any date and time used within any interface of this specification String format as specified by W3C:
                                                                YYYY-MM-DDThh:mm:ssTZD
                                                                                       Where:
                                                                                       YYYY        =       four-digit      year
                                                                                       MM = two-digit month (01=Jan, etc.)
DATETIME                                                                               DD = two-digit day of month (01-31)
                                                                                       hh = two digits of hour (00 -23)
                                                                                       mm = two digits of minute (00 - 59)
                                                                                       ss = two digits of second (00 - 59)
                                                                                       TZD = time zone designator (Z, +hh:mm or
                                                                                       -hh:mm)

Ex: 2001-12-17T09:30:47Z

                       The EID type is for representing an eUICC-ID. An eUICC-ID is
                       primarily used in the “Embedded UICC Remote Provisioning
EID                    and Management System” to identify an eUICC. See section Hexadecimal string
                       2.2.2 for EID description.
                       The ICCID type is for representing an ICCID (Integrated Circuit String representation of up to 20 decimal
                       Card IDentifier). The ICCID is primarily used to identify a digits, non-swapped.
ICCID                  Profile.
                                                                                       Ex: 8947010008, 8947010000123456784.
                       ICCID is defined according to ITU-T recommendation E.118
                       [21] , with the derivation that up to 20 digits are allowed.    89470100001234567846
                       The KCV stands for "Key Check Value". It provides the material
KCV                    for receiving entity to ensure that it uses the same key value as Hexadecimal string
                       the sending entity. See Annex F for detail of KCV computation.
                       The Mobile Station ISDN (Integrated Services Digital Network) String representation of up to 15 decimal
MSISDN                 Number                                                        digits, as defined in [22]
                                                                                       String representation of up to 15 decimal
                       The IMSI (International Mobile Subscriber Identity) used to
IMSI                                                                                   digits including MCC (3 digits) and MNC (2
                       identify the Subscriber of a Mobile Subscription.
                                                                                       or 3 digits), as defined in ITU E.212 [12]
                                                                                       String representation of an OID, i.e. of
OID                    An Object IDentifier                                            integers separated with dots (for example:
                                                                                       '1.2', '3.4.5')
TAR                    The TAR (Toolkit Application Reference) of a security domain    String - Hexadecimal string representation of
                       or an Application.                                              exactly 3 bytes
                                                                                           String representation of three integers
                       The Version type is for indicating a version of any entity used separated with dots (for example: ‘1.15.3’).
VERSION                within this specification. A version is defined by its major, minor
                       and revision number

Table 98: Simple Types

5.1.1.2 Complex Types

The SUBSCRIPTION-ADDRESS type is defined by:

Data name                           Description                            Type      No. MOC
msisdn       The MSISDN of the Subscription associated to this Profile. MSISDN        1     C
imsi         The IMSI of the Subscription associated to this Profile.      IMSI       1     C

Table 99: Subscription Address

Either the MSISDN, the IMSI, or both, SHALL be present.

NOTE:Additional address types could be added depending of the deployment mode (for example: SIP-URI).

5.1.1.2.2         POL2-RULE
The POL2-RULE type is defined by the following data structure:
Data name                                     Description                                           Type              No. MOC
              Identifies the subject on which the rule has to be applied.
subject       In the current version of this release, the possible subject is restricted to   Enumeration{PROFILE}     1       M
              “PROFILE”.
                                                                                              Enumeration{ENABLE,
action        Identifies the action/function on which the rule has to be applied.                  DISABLE,            1       M
                                                                                                   DELETE}
                                                                                                 Enumeration{
qualification Indicates the final result of the rule that has to be applied.                      Not allowed,         1       M
                                                                                                  Auto-delete}

Table 100: POL2 Rule

The Policy Rules defined in GSMA ‘Remote Provisioning Architecture for Embedded UICC’ [1] are translated as follows:

1. “Disabling of this Profile not allowed” Subject=”PROFILE”, action=”DISABLE”, qualification=”Not allowed”

2. “Deletion of this Profile not allowed” Subject=”PROFILE”, action=”DELETE”, qualification=”Not allowed”

3. “Profile deletion is mandatory when it is disabled” Subject=”PROFILE”, action=”DISABLE”, qualification=”Auto-delete”

Any other combination SHALL be treated as not valid regarding this specification release.

5.1.1.2.3         POL2
The POL2 type is defined by the following data structure:
Data name                       Description                        Type       No.   MOC
Rules        List of Policy Rules defined for a given Profile. POL2-RULE 1..N         O

Table 101: POL2 Type

An empty POL2 SHALL be represented as a POL2 data structure having no rules inside

5.1.1.2.4         PROFILE INFO
The PROFILE INFO type is defined by:
Data name                                            Description                                      Type        No.
iccid                       Identification of the Profile.                                                    ICCID       1
                            The ISD-P-AID of the ISD-P containing the Profile. This is the AID that has
isd-p-aid                   been allocated at ISD-P creation time by the SM-SR. The TAR of the ISD-             AID       1
                            P is included in the ISD-P-AID. See section 2.2.1.3.
                          Identification of the Operator owner of the Profile.
                          Once this information is associated to the Profile, it remains unchanged
mno-id                                                                                                       OID           1
                          during the Profile’s life-time.
fallbackAttribute         Boolean value to indicate the Profile having the Fall-Back Attribute set.        Boolean         1
                                                                                                          SUBSCRIP
subscriptionAddress       The address of the Subscription associated to this Profile.                       TION-          1
                                                                                                          ADDRESS
                                                                                                          Enumeratio
                                                                                                             n{
                          The current state of the ISD-P containing the Profile as per defined in
                          GSMA Remote Provisioning Architecture for Embedded UICC [1]. The                 Created,
state                                                                                                                      1
                          ‘Deleted’ state is not defined as a possible state; a ‘Deleted’ ISD-P will
                          simply not appear in the list of eUICC Profiles.                                Enabled,
                                                                                                          Disabled}
                          Identification of the SM-DP that has initially downloaded and installed the
                          Profile, or through which the Operator owning the profile MAY perform
                          platform management. This value can be empty in case the Profile has
smdp-id                   been loaded during issuance of the eUICC, else the value is mandatory.             OID           1
Once this information is associated to the Profile, i t remains unchanged
during the Profile’s life-time.
                          Indicates an Operator specific type of Profile generated by the SM -DP or
ProfileType                                                                                                 String         1
                          personalised on the eUICC at point of manufacturing (for example 3G_16K)
Indicates the amount of cumulative non volatile Memory granted to the ISD-
P to contain the Profile. Note that the allocated memory is different from
the real required memory space for Profile installation; most of the time the
allocated memory will be greater than the strict required memory space
value.
allocatedMemory           This information is provided in case of using the cumulative granted             Integer         1
                          memory mechanism.
The value is expressed in bytes.
For compatibility with earlier versions of this specification, a value of 0
SHALL denote that no cumulative granted memory was specified during
the installation of the ISD-P containing the Profile.
                          Indicates the amount of memory free within Profile allocated space. This
                          information is provided in case of using the cumulative granted memory
                          mechanism.
freeMemory                                                                                                 Integer         1

The value is expressed in bytes.

pol2                      Contains the POL2 rules defined for this Profile.                                 POL2           1

Table 102: Profile Info

NOTE:the presence of each data element is specified in Annex E, according to the function in which the PROFILE INFO is transmitted.

5.1.1.2.5        KEY-COMPONENT
The KEY-COMPONENT type is defined by:
Data                                    Description                                               Type                No. MOC
name
          Definition of the key type coding. This defines the algorithm associated
          with the key, coded on 1 byte. Meaning of the byte value follows            Hexadecimal string
type      GlobalPlatform Card Specifications [6], section 11.1.8.                  representation of exactly 1         1       M
                                                                                             byte
          i.e. '88' AES (16, 24, or 32 long keys)
            The value as a binary data. This data SHALL be encrypted with a transport
value                                                                                          Hexadecimal string          1    M
            key agreed between the provider and the requester.

Table 103: Key Component

5.1.1.2.6          KEY
The KEY type is defined by:
Data name                                          Description                                          Type         No.      MOC
index                The Key index as an integer value between 0 and 127 (as defined in
                                                                                                         integer        1       M
                     GlobalPlatform Card Specifications)
kcv                  The Key Check Value of the key                                                       KCV           1       M
              A simple key is defined using only one Key Component, but it is also                  KEY-
KeyComponents possible to define keys with multiple key components (like RSA keys)                                     1..N     M
                                                                                                    COMPONENT

Table 104: Key Type

NOTE:A key may be: o a symmetric key. In this case the key will be composed of a single key component. The key value being the same in SM-SR and eUICC SD. o an asymmetric key. In this case, the key will be most probably be composed of multiple key components. The key value in SM-SR being the counter part of the key value in the eUICC (i.e.: the public key at the SM- SR and the private key in the eUICC or vice-versa)

5.1.1.2.7          CERTIFICATE
The CERTIFICATE type is defined by:
 Data
                                                Description                                               Type        No. MOC
name
            Indicates the index of the private key, being the private counterpart of the certificate.
index       Index is an integer value between 0 and 127 (as defined in GlobalPlatform Card                Integer          1    M
            Specifications)
            Identifier of the CA that has issued (and signed) the certificate. This SHALL match
ca-id                                                                                                       OID            1    M
            the CA Identifier included in the certificate itself.
            Value of the certificate. The certificate SHALL be coded according to GlobalPlatform Hexadecimal
value                                                                                                                      1    M
            Card Specification UICC Configuration [7], section 9.2.1                             string

Table 105: Certificate Type

5.1.1.2.8          KEYSET
The KEY SET type is defined by:
     Data
                                         Description                                             Type                 No.      MOC
     name
               The version of the key set (as an integer value). The version
version        value of a key set SHALL be unique within SD definition. Integer                                        1        M
               Possible values are from 1 to 127.

Example: ‘48’ stands for a SCP03 version ‘30’

                                                                            Enumeration{
            Generally key set usage (SCP03...) can be fully deduced from
            the key set version. If version information should not be used, SCP03,     SCP80,       SCP81,
type                                                                                                                  1     O
            this element SHALL be present to indicate the real usage of TokenGeneration,
            this key set.                                                   ReceiptVerification, CA}
            The counter value linked to the key set. This element is
cntr                                                                 Integer                                      1         O
            optional: value '0' as to be considered if missing.
keys        List of keys contained in the key set                               KEY                               1..128 C(1)
             A certificate (as defined in GlobalPlatform context) as a counter
certificates part of a secret key loaded in a key set.                         CERTIFICATE                        1..128 C(1)

Table 106: KeySet Type

NOTE:A key set provisioned at SM-SR level may be composed of a set of keys or certificates.

A key set SHALL include at least one key or certificate. But for a given index, it MAY exist only one key or one certificate.

5.1.1.2.9        SECURITY-DOMAIN
The SECURITY-DOMAIN type is defined by:
  Data
                                           Description                                             Type               No.   MOC
 name
aid        The AID of the security domain                                                           AID               1     M
           The list of TARs allocated to security domain, as an SD MAY have several
tars       TARs. If this list is empty, the implicit TAR is defined by the byte 13, 14, 15         TAR            1..N      O
           of the AID.
           The security domain Provider Identification Number as defined in
sin        GlobalPlatform Card Specification [6]. The owner of the security domain           Hexadecimal string       1     M
           endorsing the Role defined in the ‘role’ data
sdin       The security domain Identification Number as defined in GlobalPlatform            Hexadecimal string       1     M
           Card Specification [6]
                                                                                             numeration{ISD-R,
role       Identification of the Role of the security domain.                                                         1     M
                                                                                                 ECASD}
keysets    The list of key sets defined within the security domain                           KEYSET               1..127 M

Table 107: Security Domain Type

5.1.1.2.10       EUICC-CAPABILITIES
The EUICC-CAPABILITIES type allows listing the capabilities supported by the eUICC.

The EUICC-CAPABILITIES type is defined by:

Data name                                             Description                                        Type       No. MOC
CAT_TP-          If CAT_TP according to ETSI TS 102 127 [25] is supported by the eUICC.                   Boolean 1     M
Support
SHALL contain the highest supported release number of ETSI TS 102 127 (defining
CAT_TP) that is implemented by the eUICC.
CAT_TP-          Conditional to the support of the CAT_TP.
                                                                                                          Version   1   C
Version
                 In case of support, the supported version SHALL be at least the minimum version
                 mandated by the present specification.
                 If RAM over HTTP according to GlobalPlatform Card Specification Amendment B              Boolean 1     M
HTTP-Support
                 [8] is supported by the eUICC.
                 SHALL contain the highest supported release number of GlobalPlatform
                 Amendment B (defining RAM over HTTP) that is implemented by the eUICC.
                 Conditional to the support of the HTTP.
HTTP-Version                                                                                              Version   1   C
                 In case of support, the supported version SHALL be at least the minimum version
                 mandated by the present specification.
                 SHALL contain the highest supported release number of ETSI TS 102 225 (defining
                 secure packet) that is implemented by the eUICC.
secure-packet-   The support of this feature as defined in ETSI TS 102 225 is not optional. The Version             1   M
version          supported version SHALL be at least the minimum version mandated by the present
                 specification.
SHALL contain the highest supported release number of this specification SGP.02
that is implemented by the eUICC. The support of this feature is obviously not
optional.
As a consequence, the eUICC SHALL be compliant will all relevant specifications
referenced in this specification.
Remote-          Note 1: If the document version has less than three digits, one or more extra “.0”
provisioning-    SHALL be appended to obtain a value that conforms to the type “Version” defined Version            1   M
version          in Table 98. For example a value of “3.1.0” denotes that the eUICC is compliant
                 with version 3.1 of SGP.02
Note 2: For backwards-compatibility reasons, if an EIS contains a value “1.1.0” for
this field, the off-card entity SHALL assume that the eUICC is com pliant with version
3.0 of SGP.02 or earlier.

Table 108: eUICC Capabilities Type

Note:          Additional eUICC capabilities MAY be indicated in the EIS’s
               AdditionalProperties (cf section A.3.5). This specification defines the
               following combinations of key:values, but other capabilities MAY be
               supported by EUMs:
Key                                                         Value                                      MOC
“gsma.ESIM.DNSResolverClientSupport” “true” or “false”                                                                  O
                                          (an absent key/value pair having the default meaning of “false”)
“gsma.ESIM.OSUpdateSupported”             “true” or “false”                                                             O

(an absent key/value pair having the default meaning of “false”)

“gsma.ESIM.updatedPlatformVersion”        an EUM specific string identifying the version of the OS after the update     C
“gsma.ESIM.JavaCardVersionSupported” This field SHALL be present if the eUICC is compliant with version 4.1 or          C
                                     later.
If the eUICC supports Java Card TM [66], the value SHALL be a string
formatted as type VERSION, indicating the version of Java Card TM
supported.
If the eUICC does not support Java Card TM [66], the value SHALL be the
string “none”.
Note 1: this field may be present if the eUICC is compliant with an earlier
version.
Note 2: See section 2.2.7 for the requirement on the minimal version.
Note 3: this field is new in version 4.1 of this specification, so servers
compliant with former versions may not interpret it; however, the previous
versions already mandate the SM-SR to carry the information e.g. in
GetEIS or in ES7.HandoverEUICC.
“gsma.ESIM.ProfilePackageVersions”      This field indicates the list of major versions including the associated        M
                                        highest minor version number of the SIMalliance eUICC Profile Package:
                                        Interoperable Format Technical Specification [53] supported by the eUICC.
                                        The list shall be provided in a single string, where each version is a string
                                        formatted as type VERSION, and the different versions, if more than one,
                                        are separated by a semi -colon.
“gsma.ESIM.UICCCapability”              This field indicates the UICC Capabilities supported by this eUICC. The         M
                                        SM-DP MAY use those fields to select or tailor the proper Profile Package
                                        to install on this eUICC.
                                        The value of this field SHALL be the hexadecimal representation of the
                                        value part of the DER encoded UICCCapability data object defined
                                        in figure 511210-A (i.e., without tag and length fields).

Table 109: AdditionalProperties denoting additional eUICC capabilities

The UICC Capabilities to be indicated in the EIS in this version of the specification are defined as follows:

-- ASN1START
-- Definition of UICCCapability
UICCCapability ::= BIT STRING {
/* Sequence is derived from ServicesList[] defined in SIMalliance PEDefinitions*/
   contactlessSupport(0), -- Contactless (SWP, HCI and associated APIs)
   usimSupport(1),         -- USIM as defined by 3GPP
   isimSupport(2),         -- ISIM as defined by 3GPP
   csimSupport(3),         -- CSIM as defined by 3GPP2
akaMilenage(4),           -- Milenage as AKA algorithm
akaCave(5),               -- CAVE as authentication algorithm
akaTuak128(6),            -- TUAK as AKA algorithm with 128 bit key length
akaTuak256(7),            -- TUAK as AKA algorithm with 256 bit key length
rfu1(8),                  -- reserved for further algorithms
rfu2(9),                  -- reserved for further algorithms
gbaAuthenUsim(10),        -- GBA authentication in the context of USIM
gbaAuthenISim(11),        -- GBA authentication in the context of ISIM
mbmsAuthenUsim(12),       -- MBMS authentication in the context of USIM
eapClient(13),            -- EAP client
javacard(14),             -- Javacard support
multos(15),               -- Multos support
   multipleUsimSupport(16), -- Multiple USIM applications are supported within the
same Profile
   multipleIsimSupport(17), -- Multiple ISIM applications are supported within the
same Profile
   multipleCsimSupport(18),   -- Multiple CSIM applications are supported within
the same Profile
   berTlvFileSupport(19), -- BER TLV files
   dfLinkSupport(20),      -- Linked Directory Files
   catTp(21),              -- Support of CAT TP
   getIdentity(22),        -- Support of the GET IDENTITY command as defined in
ETSI TS 102 221 [6]
   profile-a-x25519(23),   -- Support of ECIES Profile A as defined in 3GPP TS
33.501 [XX]
   profile-b-p256(24),     -- Support of ECIES Profile B as defined in 3GPP TS
33.501 [XX]
   suciCalculatorApi(25)   -- Support of the associated API for SUCI derivation as
defined in 3GPP 31.130 [YY]

}

Figure 511210-A: Definition of UICCCapability

Future versions of this specification may add more bits to UICCCapability. The SM-SR SHALL transparently handle additional bits. The SM-DP SHALL ignore unknown additional bits.

5.1.1.2.11    AUDIT TRAIL RECORD
The AUDIT-TRAIL RECORD type contains the description of a Platform or a Profile
Management operation performed by SM-SR or a notification received by SM-SR from the
given eUICC.
The AUDIT-TRAIL-RECORD type is defined by:
       Data name                            Description                         Type      No.    MOC
EID                   The EID type is for representing an eUICC-ID. An eUICC-ID is primarily EID            1      M
                      used in the “Embedded UICC Remote Provisioning and Subscription
                      Management System” to identify an eUICC. See section 2.2.2 for EID
                      description.
SMSRid                SMSRid defined SM-SR storing given eUICC                                  OID         1      M
operationDate         Date and time of logged operation                                         DATETIME    1      M
                      Notification Type as defined in section 4.1.1.11 or Command Type as Hexadecimal 1            M
operationType         defined below.                                                      String
                      Identification of the entity that has requested the operation to be       OID         1      C
requesterId           performed on the eUICC
                      For command type Function Execution Status as defined in section 5.1.5 ExecutionStat
status                is stored                                                                            1       C
                                                                                             us
                      The ISD-P-AID of the ISD-P containing the Profile. Not present in case
                      the operation type does not concern a specific ISD-P AID (example: AID
ISD-P-AID                                                                                                   1      C
                      EstablishISDRkeyset)
                      The ICCID of the Profile.
ICCID                                                                                           String      1      C
                      Not present in case the operation type does not concern a specific ISD-
                      P AID (example: EstablishISDRkeyset)
                      See ETSI TS 102 223 [3], clause 8.20                                      Hexadecimal
IMEI                                                                                                        1      C
                                                                                                String
                      See ETSI TS 102 223 [3], clause 8.81                                      Hexadecimal
MEID                                                                                                        1      C
                                                                                                String

Table 110: Audit Trail Record Type

NOTE:Requester Id OID is empty in case of notification.

5.1.1.2.12       Command Type
Command type coding:
 ‘0100’: CreateISDP
 ‘0200’: EnableProfile
 ‘0300’: DisableProfile
 ‘0400’: DeleteProfile
 ‘0500’: eUICCCapabilityAudit
 ‘0600’: MasterDelete
 ‘0700’: SetFallbackAttribute
 ‘0800’: EstablishISDRkeyset
 ‘0900’:FinaliseISDRhandover
 ‘0A00’: SetEmergencyProfileAttribute
 ‘0B00’ to ‘FF00’ RFU
NOTE:      1st byte is reserved for Notification Type as defined in section 4.1.1.11
5.1.1.2.13         EIS
The EIS type is for representing eUICC Information Set.
Data name                                     Description                                         Type           No.
eid                        Identification of the eUICC.                                       EID                       1
                           See section 5.1.1.1 for type description.
                           This information is initially provided by the EUM at
                           registration time, and remains unchanged during all the
                           eUICC’s lifetime.
eum-id                     Identification of the eUICC Manufacturer (i.e. Card Vendor)        OID                       1
                           that has manufactured the eUICC.
                           This information is initially provided by the EUM at
                           registration time, and remains unchanged during all the
                           eUICC’s lifetime.
                           The ‘eum-id’ indication, jointly with the ‘platformType’ and
                           ‘version, may especially be useful for the SM -DP to perform
                           the Profile generation and packaging.
productionDate             The date/time where the eUICC has been manufactured by             DATETIME                  1
                           the card vendor.
This information is initially provided by the EUM at
registration time, and remains unchanged during all the
eUICC’s lifetime.
platformType               Indication of the eUICC platform/OS type.                          String                    1
                           This information is initially provided by the EUM at
                           registration time, and remains unchanged during all the
                           eUICC’s lifetime.
The content of this field is not enforced by this specification;
the EUM can use any convenient string value.
platformVersion            Indication of the version of the eUICC platform/OS type.           VERSION                   1
                           This information is initially provided by the EUM at
                           registration time, and remains unchanged during all the
                           eUICC’s lifetime.
remainingMemory            Indicates the current total available memory (whatever the         Integer                   1
                           underlying technology, flash or eeprom) for Profile
                           download and installation.
                           This value MAY be either:-
    a value cached by the SM-SR based on the initial
     total memory and memory required by all Profiles
     currently loaded on the eUICC.
        a value retrieved from the eUICC
The value is expressed in Bytes.
This information is initially provided by the EUM at
registration time, but may change according to the eUICC
usage.
Availablememoryforprofil   Indicates the free memory (whatever the underlying                 Integer                   1
es                         technology, flash, eeprom) without any Profile, available for
                           Profile(s) loading and installation.
                           This value is initially provided by the EUM at the registration
                           time. It is calculated when the ISD-R and the ECASD are
                           created, instantiated and personalized.
                           This value is informative. The SM-SR cannot know how this
                           value evolves during the card life cycle when a patch or a
                           filter is applied or when the ECASD or the ISD-R
                           configuration is modified. The SM-SR SHALL return the
                           value that it received initially via ES1.registerEIS or via
                           ES7.HandoverEUICC.
lastAuditDate        Some information part of the EIS can be refreshed by             DATE                        1
                     requesting directly the information to the eUICC to have the
                     list of information that can be retrieved. This indicates the
                     last date where such operation has been performed, and
                     so indicating the freshness of the information sto red at SM-
                     SR level.
This information is optional. If not present, it means that no
audit has been performed on the eUICC.
smsr-id              Identification of the SM-SR currently in charge of eUICC         OID                         1
                     management.

This information may change during the eUICC’s l ifetime.

isd-p-loadfile-aid   AID of the Executable Load File to be used for instantiation     AID                         1
                     of an ISD-P.
                     This information is initially provided by the EUM at
                     registration time, and remains unchanged during all the
                     eUICC’s lifetime.
                      AID of the Executable Module to be used for instantiation of
                      an ISD-P.
isd-p-module-aid      This information is initially provided by the EUM at AID                                     1
                      registration time, and remains unchanged during all the
                      eUICC’s lifetime.
 profiles             List of Profiles currently installed on the eUICC.               PROFILE INFO               1..N
                      This information is initially provided by the EUM at
                      registration time, and may change during the eUICC’s
                      lifetime.
ISD-R
                      Contains the information related to the ISD-R                    SECURITY-DOMAIN             1
                      Contains the information related to the ECASD
                      Although the type of this data is SECURITY-DOMAIN, some
                      restrictions apply in order to ensure the consistency of the
                      signature when this structure is stored or reconstructed:
                               The data SHALL contain one single Tar element,
                                with the TAR value for the ECASD specified in
ECASD
                                Annex H.                                             SECURITY-DOMAIN               1
                               If there is more than one Keyset or Certificate per
                                ECASD, they SHALL be ordered according to:
                                      o     The Keyset 'version' if there is more
                                            than one Keyset
                                      o     The Certificate 'index' if there is more
                                            than one Certificate per Keyset
                      Contains the capabilities supported by the eUICC.
eUICC-Capabilities    This information is initially provided by the EUM at EUICC-                                  1
                                                                           CAPABILITIES
                      registration time.
audit trail          History of all the platform and Profile Management               AUDIT-TRAIL-               0..N
                     operations or eUICC notifications related to the eUICC           RECORD
signatureAlgorithm   Indicates the signature algorithm used by the EUM to sign        Enumeration{           1
                     the relevant part of the EIS. See Annex E to have details of
                     the data that SHALL be included in the signature.                rsa-sha256,     rsa-
                                                                                      sha384,
                                                                                      rsa-sha512,
                     The algorithm naming follows RFC 4051 [24]
                                                                                      ecdsa-sha256,
                                                                                      ecdsa-sha384,
                                                                                      ecdsa-sha512
                                                                                      }
Signature                  Signature value of the EUM. See Annex E to have details         Byte[]                       1
                           of the data included in the computation of the signature
AdditionalProperty         Optional additional information. See table 111-B                See Annex A.TODO         0..N

Table 111: EIS Type

NOTE:NOTE: the presence of each data element is specified in Annex E, according to the function in which the EIS is transmitted.

NOTE:The ISD-P(s) are not represented in the EIS as a pure SECURITY-DOMAIN data type; ISD-P information is directly included in the Profile representation without distinction as the SM-SR doesn’t have access to ISD-P credentials.

NOTE:All values defined as Integer SHALL be encoded in decimal.

For extensibility purpose, additional information MAY be carried in the EIS. These information SHALL be specified as AdditionalProperties as specified in section Error! R eference source not found.. This specification defines the following combinations of key:values, but other combinations MAY be supported by EUMs:

                     Key                                                           Value
“gsma.ESIM.ES1.transportKey”                  A string agreed between requester and provider, allowing to identify the
                                              transport key used to cipher key components
“gsma.ESIM.ES1.SCP80.KeySize”                 Length of keys in SCP80 keysets of ISD-R”
“gsma.ESIM.ES1.SCP81.KeySize”                 Length of keys in SCP81 keysets of ISD-R”
“gsma.ESIM.EmergencyProfileAttribute.AID” ISD-P-AID of the Profile with the Emergency Profile Attribute Set, if any. If this
                                          value is empty or missing, no Profile on this eUICC has the Emergency Profile
                                          Attribute set.
“gsma.ESIM.TestProfile.AID”                   ISD-P-AID of the Test Profile, if any. If this value is empty or missing, no Test
                                              Profile is present on this eUICC.

Table 111-2: Common Additional Properties

5.1.1.2.14         PLMA
The PLMA type is defined by:
      Data name                                         Description                                       Type     No.      MOC
mno-id                 Identification of the Operator owner of the Profiles concerned by this PLMA.
                                                                                                          OID       1       M
                       See section 5.1.1.1 for type description.
profileType            Identification of the Profile Type of the Profiles concerned by this PLMA.
                       This is an arbitrary String that is meaningful only in the context of a given
                       Operator (mno-id).                                                                 String    1       M
                       An empty profileType string means all Profile owned by the Operator identified
                       by mno-id, and having an empty Profile Type or no Profile Type in the EIS.
                       Identification of the M2M SP that will issue requests to the SM -SR to perform
m2m-sp-id              authorised operations, or that will receive authorised notifications.              OID       1       M
                       See section 5.1.1.1 for type description.
See sections 5.7.1.1 and 5.7.1.2 for the specification of how the SM -SR can
identify the requester when it receives ES4 and ES3 requests
                       A list of operation names that identify either requests that the M2M SP will be
                       authorised to send to the SM -SR, or notifications that the M2M SP is authorised
                       to receive from the SM-SR, related to the profiles matching the other criteria in
                       this request.
                     Any operation not in this list is not or no longer authorised for Profiles matching
authorisedOperations the other criteria in this PLMA: in this case the M2M SP is not authorised to String 0…N M
                     execute the request, or to receive the n otification, identified by the operation
                     name.
An empty list means no operation is allowed, and can be used to remove all
authorisations, for Profiles matching the other criteria in this PLMA
See below the possible values of this String

Table 511214-A: PLMA Type

Each String in the authorisedOperations list SHALL be a distinct operation name among table 511214-B below.

Operation name                                   Meaning of the corresponding authorisation
                               The M2M SP is authorised to view any Profile that matches the other
GetEIS                         criteria in the PLMA in the EIS it could get via ES3 or ES4
                                The M2M SP is authorised to audit via ES3 or ES4 any Profile that
AuditEIS                        matches the other criteria in the PLMA
                                  The M2M SP is authorised to request EnableProfile via ES3 or ES4 on
EnableProfile                     any Profile that matches the other criteria in the PLMA
                                   The M2M SP is authorised to request DisableProfile via ES3 or ES4 on
DisableProfile
                                   any Profile that matches the other criteria in the PLMA
                                  The M2M SP is authorised to request deletion via ES3 or ES4 on any
DeleteProfile
                                  Profile that matches the other criteria in the PLMA
                                          The M2M SP is authorised to request setting the Emergency Profile
setEmergencyProfileAttribute              Attribute via ES3 or ES4 on any Profile that matches the other criteria in
                                          the PLMA
                                           The Operator or M2M SP is authorised to unset the Emergency Profile
unsetEmergency ProfileAttribute            Attribute on any Profile that matches the other criteria in the PLMA, as the
                                           result of requesting to set it on another Profile
                                      The M2M SP is authorised to request setting the Fall-Back Attribute via
SetFallBackAttribute                  ES3 or ES4 on any Profile that match the other criteria in the PLMA
                                       The Operator or M2M SP is authorised to unset the Fall-Back Attribute on
UnsetFallBackAttribute                 any Profile that match the other criteria in the PLMA, as the result of
                                       requesting to set it on another Profile
                                         The M2M SP is authorised to request UpdateSubscriptionAddress via
UpdateSubscriptionAddress                ES3 or ES4 on any Profile that match the other criteria in the PLMA
                                            The M2M SP is authorised to receive notification via ES3 or ES4 that any
HandleProfileEnabledNotification            Profile that matches the other criteria in the PLMA has been Enabled
                                            The M2M SP is authorised to receive notification via ES3 or ES4 that any
HandleProfileDisabledNotification
                                            Profile that matches the other criteria in the PLMA has been Disabled
                                           The M2M SP is authorised to receive notification via ES3 or ES4 that any
HandleProfileDeletedNotification           Profile that matches the other criteria in the PLMA has been deleted
                                             The M2M SP is authorised to receive notification via ES3 or ES4 that any
HandleProfileDownloadedNotification
                                             Profile that matches the other criteria in the PLMA has been downloaded
                                                  The M2M SP is authorised to receive notification via ES3 or ES4 that the
HandleProfilePolicyRulesUpdatedNotification       POL2 has been updated on any Profile that matches the other criteria in
                                                  the PLMA
                                                   The M2M SP is authorised to receive notifications via ES3 or ES4 that any
HandleEmergencyProfileAttributeSetNotification     Profile that matches the other criteria in the PLMA has had its Emergency
                                                   Profile Attribute set.
                                                 The M2M SP is authorised to receive notifications via ES3 or ES4 that any
HandleEmergencyProfileAttributeUnsetNotification Profile that matches the other cri teria in the PLMA has had its Emergency
                                                 Profile Attribute unset.
                                                  The M2M SP is authorised to receive notifications via ES3 or ES4 that any
HandleProfileFallBackAttributeSetNotification     Profile that matches the other criteria in the PLMA has had its Fall -Back
                                                  Attribute set.
                                                   The M2M SP is authorised to receive notifications via ES3 or ES4 that any
HandleProfileFallBackAttributeUnsetNotification    Profile that matches the other criteria in the PLMA has had its Fall -Back
                                                   Attribute unset.

Table 511214-B: List of Operation Eligible to PLMA

NOTE:There is no explicit operation UnsetEmergencyProfileAttribute and UnsetFallBackAttribute; the Emergency Profile Attribute or Fall-Back Attribute are only unset as the result of setting it on another Profile.

5.1.1.2.15       ONC
The ONC type is defined by:
      Data name                                          Description                                       Type   No.   MOC
mno-id                 Identification of the Operator owner of the Profiles concerned by this ONC.
                                                                                                            OID   1      M
                       See section 5.1.1.1 for type description.
profileType            Identification of the Profile Type of the Profiles concerned by this ONC.
                       This is an arbitrary String that is meaningful only in the context of a given
                       Operator (mno-id).                                                            String       1      M
                       An empty profileType string means all Profiles for this mno -id which have no
                       Profile Type set in the EIS.
A list of notifications names that identify which notifications SHALL NOT be sent
from the SM-SR to the Profile owning Operator, related to the Profiles
associated with the Profile Type, provided in this request.
Any notification names in this list is not or no longer requested by the Operator
owning the Profile, related to the Profiles associa ted with the Profile Type,
provided in this request.
                       An empty list means that all notifications are requested by the Operator owning
                       the Profile, related to the Profiles associated with the Profile Type, provided in
                       this request. It can be used to remove a ll previously configured ONC for this
discardedNotifications Profile Type.                                                                      String 0…N M
                       See table 511215-B below for the format of this String.
If no Operator Notification Configuration has yet been set in the SM -SR for a
given Profile Type, then the Operator SHALL receive all notifications for status
changes for its own Profiles, associated with this Profile Type, see also section
3.21 for details.

Table 511215-A: ONC Type

Each String in the discardedNotification list SHALL be a distinct notification name among table 511215-B below.

Notification name                                      Meaning of the corresponding configuration
                                             The Operator owning the Profile receives no notifications via ES3 or ES4
HandleProfileDisabledNotification
                                             when a Profile, associated with the Profile Type in the ONC, was disabled.
                                             The Operator owning the Profile receives no notifications via ES3 or ES4
HandleProfileEnabledNotification
                                             when a Profile, associated with the Profile Type in the ONC, was enabled.
                                           The Operator owning the Profile receives no notifications via ES3 or ES4
HandleProfileDeletedNotification
                                           when a Profile, associated with the Profile Type in the ONC, was deleted.
                                           The Operator owning the Profile receives no notifications via ES3 or ES4
HandleSMSRChangeNotification               when the SM-SR, managing an eUICC, has changed and the eUICC is
                                           hosting a Profile which is associated with the Profile Type in the ONC.
                                                    The Operator owning the Profile receives no notifications via ES3 or ES4
HandleEmergencyProfileAttributeSetNotification      when the Emergency Profile Attribute was set on a Profile, associated with
                                                    the Profile Type in the ONC.
                                                 The Operator owning the Profile receives no notifications via ES3 or ES4
HandleEmergencyProfileAttributeUnsetNotification when the Emergency Profile Attribute was unset on a Profile, associated
                                                 with the Profile Type in the ONC
                                                   The Operator owning the Profile receives no notifications via ES3 or ES4
HandleProfileFallBackAttributeSetNotification      when the Fall-Back Attribute was set on a Profile, associated with the
                                                   Profile Type in the ONC.
                                                    The Operator owning the Profile receives no notifications via ES3 or ES4
HandleProfileFallBackAttributeUnsetNotification     when the Fall-Back Attribute was unset on a Profile, associated with the
                                                    Profile Type in the ONC

Table 511215-B: List of Notifications Requested by ONC

5.1.2 Request-Response Function

A request-response function functionally corresponds to the case where a requestor Role sends a request message to a replier Role which receives and processes the request, ultimately returning a message in response. A function may take input data and may provide output data. A function may also deliver no output data.

     Role A
(function requester)
Request (input data)                         Response ([output data])
     Role B
(function provider)

Figure 48: Functions as a Request-Response Data Exchange

At function definition level nothing is said about if the function is synchronous or asynchronous.

5.1.2.1 Validity Period

When a function is called, the function provider takes the responsibility to execute all the individual execution steps that are required to complete the function. Such processing may require some time to complete, but the function caller might want this processing duration to not exceed a specific amount of time called the "function validity period", as detailed in the following use cases:

      The function processing might no longer be valuable if it ends after the validity period.
       For example, a function is only valuable if it is executed within a minute. If more than
       a minute has elapsed, then it is no longer required to continue the function execution.
    Processing might not want to wait for an external event that might not occur before a
       very long time or an event that might even never occur at all. For example, it is
       possible when performing an OTA dialog that the Device is unreachable (switched
       off, lost…), or that an acknowledgement message coming from the Device is lost on
       the network (for example the loss of a PoR coming from an eUICC). If so, it might not
       be acceptable to wait several days or weeks for the Device to be switched on again,
       or even to wait forever for an acknowledgement message that will never come.
    It is desirable that the function provider system is not overloaded with requests that
       will be pending for a long period. The function caller would like to be notified as soon
       as possible that the function cannot be processed within a specific amount of time,
       and may then implement a calling side retry Policy.
By providing a validity period, the function caller indicates a specific amount of time to the
function provider to process the function. As a consequence, during this validity period, the
function caller SHALL NOT issue the same request again as it might generate duplicate
execution steps within the function provider system.

After the end of the validity period, the function provider SHALL no longer continue with new execution steps. It is only mandated to tell the function caller that the function processing has expired. It is then the caller responsibility to either:

       Request the same function again,
       Or simply abandon the overall process into which the function was called.
Input data
                                                     Description                                              Type     No. MOC
  name
Function
Requester      Identification of the function requester.                                                      String    1   M
Identifier
               Identification of the function call.
               This identifier enables to manage function call retry policies.
               When requesting for the execution of a function, the function caller SHALL provide a
               unique Function Call Identifier. Uniqueness is to be ensured in its own perimeter.
               In case the function caller wants to retry the same function, then it SHALL perform the
               same function call, providing the same Function Call Identifier.
Function Call
                                                                                                         String         1   C
Identifier    On function provider side, when receiving this retry attempt, if a call to a function if
              performed with an Function Call Identifier of a function already in process in its system,
              then the function provider SHALL refuse the new call
If the function provider does not want to implement any retry Policy, then it might ignore
this field.
The Function Call identifier is only mandatory for request-response functions. It SHALL
NOT be present for notification functions.
               This field defines the length of the period (provided as a number of seconds) during
               which the request is valid. The period starts at the time the function call was received by
               the function provider and ends a number of seconds later. During this period of time, the
Validity       function provider has the responsibility to execute the function.
                                                                                                              Integer   1   O
Period
               The function provider, on reception of the function call, MAY:
     Accept the function call: in that case the function provider accepts the provided
      validity period
     Rej ect the function call: if the function provider immediately considers that the
      validity period is invalid (for example too long or too short) or cannot fulfil the
      requirements (i.e. cannot start the sequence of operations so that all of the
      operations are completed within the validity period), it SHALL NOT process the
      function and SHALL immediately return a Function Execution Status output
      parameter with a Status field set to 'Failed' and a Subject code and Reason
      code of the Status Code Data field set to 'Val idity Period not accepted'.
      The function provider SHALL also indicate to the function caller an acceptable
      amount of time into which the request could be fulfilled, by setting the
      Acceptable Validity Period field in the output header.
The Validity Period is only present (but optional) for request-response functions. If not
specified, the function caller doesn’t require any specific validity period. Nevertheless the
function provider is free to apply any internal rule to restrict the validity period (it could be
the case to ensure that a function request will never stay stacked in the system). In that
case the function provider SHALL indicate to the function caller the applied validity period
value in the Acceptable Validity Period field in the output heade r.

The Validity Period SHALL NOT be present for notification functions.

Table 112: Validity Period Functions Identifier

5.1.2.2 Exceptions

During the processing of a function, an unexpected behaviour may happen. This event, called an exception in this specification, may cause the function to be ended before the functional work to be completed (the exception is then considered as an error), or may let the functional work continue, but under specific conditions (the exception is then called a warning).

This is the function provider’s responsibility to give information on any exception encountered during the processing of a function; however the behaviour of the function caller when receiving this exception may depend on its own context (for example stop it s current processing, or perform a retry attempt, or try a workaround processing, etc.)

5.1.3 Notification Handler function

In some cases, functions are considered as notifications as they functionally correspond to events sent from one Role to another. If so, the Role that generates the notification is called the notification source or the notifier, and the Role that receives the notification is called the notification destination or the notification recipient or notification handler.

      Role A
(notification source)

Notification (data)

       Role B
(notification recipient)

Figure 49: Notification as One Way Events

By definition, no validity period is applied for a notification, and no data can be returned back by the notification recipient to the notification source.

Similarly, no exception is expected in the context of a notification.

5.1.4 Functions Input Header

All functions (request-response and notification handler) SHALL include the following he ader as part of the input data:

Input data
                                                        Description                                                  Type    No. MOC
  name
Function
Requester       Identification of the function requester.                                                            String   1   M
Identifier
Identification of the function call.
This identifier enables to manage function call retry policies.
When requesting for the execution of a function, the function caller SHALL provide a
unique Function Call Identifier. Uniqueness is to be ensured in its own perimeter.
                In case the function caller wants to retry the same function, then it SHALL perform the
                same function call, providing the same Function Call Identifier.
Function Call
                                                                                                                     String   1   C
Identifier
                On function provider side, when receiving this retry attempt, if a call to a function if
                performed with an Function Call Identifier of a function already in process in its system,
                then the function provider SHALL refuse the new call
If the function provider does not want to implement any retry Policy, then it might ignore
this field.
The Function Call identifier is only mandatory for request-response functions. It SHALL
NOT be present for notification functions.
This field defines the length of the period (provided as a number of seconds) during
which the request is valid. The period starts at the time the function call was received by
the function provider and ends a number of seconds later. During this period of time, the
function provider has the responsibility to execute the function.
The function provider, on reception of the function call, MAY:
          Accept the function call: in that case the function provider accepts the
           provided validity period
                          Rej ect the function call: if the function provider immediately considers that the
                           validity period is invalid (for example too long or too short) or cannot fulfil the
                           requirements (i.e. cannot start the sequence of operations so that all of the
                           operations are completed within the validity period), it SHALL NOT process
                           the function and SHALL immediately return a Function Execution Status
Validity                   output parameter with a Status field set to 'Failed' and a Subject code and
                                                                                                               Integer        1   O
Period                     Reason code of the Status Code Data field set to 'Validity Period not
                           accepted'.
                           The function provider SHALL also indicate to the function caller an acceptable
                           amount of time into which the request could be fulfilled, by setting the
                           Acceptable Validity Period field in the output header.
The Validity Period is only present (but optional) for request -response functions. If not
specified, the function caller doesn’t require any specific validity period. Nevertheless
the function provider is free to apply any internal rule to restrict the validity period (it could
be the case to ensure that a function request will never stay stacked in the system). In
that case the function provider SHALL indicate to the function caller the applied validity
period value in the Acceptable Validity Period field in the output header.

The Validity Period SHALL NOT be present for notification functions.

Table 113: Functions Input Headers

Additionally to this common header, each function may define its own set of additional input data.

5.1.5 Functions Output Header

All functions (request-response) SHALL include the following header as part of the output data. Notifications don't have any output data.

Output data name                                Description                                 Type            No.       MOC
                            The start time and date of the real processing of the
                            function by the function provider (and not the time and date   DATETIME            1          O
Processing Start
                            of reception of the request).
                            The function processing end time and date.                     DATETIME            1          O
Processing End
In case the validity period provided as input parameter is
not acceptable, then the function provider SHALL return an
acceptable value to the function caller (see section 5.1.4)
as a number of seconds.
Acceptable Validity                                                                           Integer          1          C
Period              In case the function call has been rejected because of a
                    non acceptable validity period the function caller might
                    then call again the same function with a validity period that
                    is more convenient (but that MAY however differ from the
                    exact value of the Acceptable Validity Period field sent in
                    response to the previous function call).
Indicates whether the processing has been completed
correctly or not.
Function     Execution If required, provides information to give details on the ExecutionStatu                 1          M
                       processing result (status code, status code reason, status     s
Status
                       message…).

The Execution Status type is described below.

Table 114: Functions Output Headers

Where an Execution Status is:

 Data
                                             Description                                              Type           No. MOC
 name
           It indicates whether the processing has been completed correctly or not.
           Value 'Executed-Success' means that the function has been processed correctly.       Enumeration
           Application output data MAY optionally be part of the function response.              {Executed-
                                                                                                  Success,
           Value 'Executed-WithWarning' means that the function has been processed
           correctly, but that warnings have been generated during this execution.               Executed-           1   M
Status     Application output data MAY optionally be part of the function response in order     WithWarning,
           to provide details on the warnings.
                                                                                                   Failed,
           Value 'Failed' means that the function execution has encountered errors during
                                                                                                  Expired}
           its processing. The Status Code Data output structure SHALL give the reason of
           error in the processing (values depend on the function and MAY be
           implementation dependant).
Value 'Expired' means that the validity period of the request has expired before
the completion of the function processing. The Status Code Data output structure
MAY give the reason of expiration of the function.
            It provides the reason of the Status.
Status
            Present only if the Status is 'Execute-WithWarning', 'Failed', or 'Expired'.       Status code data   1       O
code
data        The Status Code Data type is described below.

Table 115: Execution Status

Where a Status code data is:

Data name                                     Description                               Type      No.    MOC
                             Represents the system element concerned by the exception. A
Subject code                                                                                     OID         1        M
                             normative list of subjects is given in section 5.1.6.1
                             Represents the reason of the exception. A normative list of
Reason code                                                                                      OID         1        M
                             reasons is given in section 5.1.6.2
                             The identifier of the subject or any identification data of the
                             subject that caused the exception (for example ICCID of the
Subject identifier           Profile when the Subject is a "Profile").                          String       1        O
                             The possible values of the Subject Identifier depend on the
                             function.
                             It provides a textual and human readable explanation of the
Message                                                                                         String       1        O
                             exception. The Message value is implementation dependant

Table 116: Status Code

5.1.6 Status Code

Status codes are used in a function call to indicate that an exception occurred during the processing of the function.

The “status code” is part of the Function output header (as defined in section 5.5.5). In this specification, the status codes are representing any exception from a simple warning to an error.

      When an error is raised (function output header status is ‘Failed’), it means that the
       expected functional behaviour has not been completed.
    When a warning is raised (function output header status is ‘Executed -WithWarning’’),
       it means that the expected functional behaviour has been completed, but under
       specific conditions that SHOULD be pointed out by the function provider.
Both Subject code and Reason code fields of the Status code data of the function output
header are represented by an OID (Object IDentifier). These identifiers refer to a list of pre -
defined elements and reasons (see below for details).

5.1.6.1 Subject Code

The Subject code represents, from the function provider perspective, the entity on which the exception occurred. The subject code can either be its own system (for example: an internal error), a part of the system (for example: eUICC, Profile …) or even the function caller itself (for example: Identification issue).

GlobalPlatform System, Messaging Specification for Management of Mobile-NFC Services [23] already defines some subject codes that are organised as a tree representation. This specification proposes to reuse the category “1. Generic” as defined in [23].

The subjects codes linked with the “Remote Provisioning Architecture for Embedded UICC”, are regrouped under a dedicated category, which has the identifier value “8. eUICC Remote Provisioning” to avoid any conflict with the categories already defined in [23].

The possible values for the Subject code used in the context of this specification are defined as follow:

1.      Generic
        1.1.      Function Requester
        1.2.      Function Provider
                  1.2.1. Validity Period
        1.3.      Protocol
                  1.3.1. Protocol Format
                  1.3.2. Protocol Version
        1.4.      External Resource
        1.5       Extension Resource
        1.6       Function
8.      eUICC Remote Provisioning
        8.1 eUICC
                  8.1.1 EID
        8.2 Profile
                  8.2.1 Profile ICCID
                  8.2.2 POL1
                  8.2.3 POL2
                  8.2.4 Void
                  8.2.5 Profile Type
                  8.2.6 Subscription Address
                  8.2.7 PLMA
                  8.2.8 ONC
        8.3 ISD-P
                  8.3.1 ISD-P-AID
        8.4 ISD-R
        8.5 ECASD
                  8.5.1 Certification Request
                  8.5.2 Embedded UICC Certificate Authority
        8.6 EIS

8.7 SM-SR

8.7.1 SM-SR certificate

8.8 SM-DP

8.9 M2M SP

8.10 Operator

5.1.6.2 Reason Code

The Reason code represents, from the function provider perspective, the reason why the exception occurred.

As for Subject Code, GlobalPlatform System, Messaging Specification for Management of Mobile-NFC Services [23] already defines some reason codes that are organised as a tree representation. This specification proposes to reuse the following categories coming from [23]:

1. Access error

2. Format error 3. Conditions of use not satisfied 4. Processing error 5. Transport error 6. Security error The possible values for the Reason code are defined as follow:

1.     Access Error
       1.1.   Unknown (Identification or Authentication)
       1.2.   Not Allowed (Authorisation)
2.     Format Error
       2.1.   Invalid
       2.2.   Mandatory Element Missing
       2.3.   Conditional Element Missing
3.     Conditions of Use Not Satisfied
       3.1.   Unsupported
       3.2.   Maximum Size Exceeded
       3.3.   Already in Use (Uniqueness)
       3.4.   Invalid Destination
       3.5.   Invalid Transition
       3.6.   Related Objects Exists
       3.7.   Unavailable
       3.8.   Refused
       3.9    Unknown
4.      Processing Error
        4.1.   Function Already in Progress
        4.2.   Execution Error
        4.3.   Stopped on Warning
        4.4.   Busy
        4.5.   Operation Already Processed
        4.6.   Not Present / Missing
        4.7.   Generation Not Possible
        4.8.   Insufficient Memory
        4.9.   Unassigned
5.      Transport Error
        5.1.   Inaccessible
        5.2.   Timeout
        5.3.   Time to Live Expired
        5.4    Delivered With No Response
        5.5    Connection Lost
6.      Security Error
        6.1.   Verification Failed
        6.2.   Decipher Failed
        6.3.   Certificate Expired

5.1.6.3 Status Code Example

Identification issue example:

State: The function requester tries to access a function, but its credentials are not k nown to the function provider

Function processing: The function provider raises an internal exception, as the function requester couldn’t be identified

Returned Status Code:

 Subject code: 1.1 – Function requester  Reason code: 1.1 – Unknown Platform Management issue:

State: The function requester tries to create a new ISD-P, but with an ICCID already in used for another Profile

Function processing: The function provider raises an internal exception, as there is a conflicting AID.

Returned Status Code:

      Subject code: 8.2.1 – Profile ICCID
      Reason code: 3.3 – Already in use

5.1.6.4 Common Function Status Code

The following table provides the normative list of status codes that may be raised by any function defined in this specification. These statuses SHALL be implemented.

In addition each function MAY raise additional specific status codes. In that case, it is defined explicitly in the function description.

As an implementer’s choice, it is also possible that a function MAY return additional status codes not described in this specification. The function caller SHALL be ready to handle such situation.

Common status code when ‘Function execution status’ is ‘failed’

Subj ect                 Reason
            Subj ect                          Reason                                       Description
 code                     code
                                       Unknown
           Function
  1.1                         1.1      (Identification     or The function caller is unknown to the function provider.
           requester
                                       Authentication)
         Function                    Not            allowed
1.1                         1.2                               The function caller is not allowed to use this function.
         requester                   (authorisation)
         Function                                             Internal processing error (this status code SHALL be returned only
1.2                         4.2      Execution error
         provider                                             when no more accurate status code can be returned)
         Function
1.2                         4.4      Busy                     Busy: not possible to process the function for the moment
         provider
          Validity                                             The requested validity period is not accepted by the function
1.2.1                        3.8      Refused
          period                                               provider.
                                                              An input parameter of the function is invalid (wrong format, not
                                                              acceptable value…). The contextual message conveyed with the
1.6      Function           2.1      Invalid                  status code data SHALL indicate the name of the concerned
                                                              parameter.
                                                              A mandatory input parameter of the function is missing. The
                                     Mandatory     Element
1.6      Function           2.2                               contextual message conveyed with the status code data SHALL
                                     Missing
                                                              indicate the name of the concerned parameter.
                                                              A conditional input parameter of the function is missing. The
                                     Conditional   Element
1.6      Function           2.3                               contextual message conveyed with the status code data SHALL
                                     Missing
                                                              indicate the name of the concerned parameter.

Table 117: Function Execution Status ‘Failed’ Codes

Common status code when ‘Function execution status’ is ‘Expired’

Subj ect               Reason
           Subj ect                  Reason                                        Description
 code                  Code
                                  Time to The function execution request has expired (end of validity period has been
                                          reached). This may be because the server had no time to execute the function or
1.6      Function     5.3         live
                                          because the function was requesting a remote communication with the eUICC
                                  expired
                                          which was not present on the network during all the validity period.

Table 118: Function Execution Status ‘Expired’ Codes

5.2 ES1 (EUM – SM-SR) Interface Description

5.2.1 Register EIS

Function name: RegisterEIS

Related Procedures: eUICC registration at SM-SR: register a new EIS

Function group: eUICC Management

Function Provider: SM-SR

Description:

This function allows an eUICC Manufacturer (EUM) to register an eUICC represented by its eUICC Information Set (EIS) within an identified SM-SR information database.

The EIS contains the complete set of data that is applicable for the SM-SR to manage the lifecycle of this eUICC. This data set is split in two different parts:

    A fixed signed part containing the identification of the eUICC
    A variable part containing the keys for the Platform Management plus the list of the
     different Profile loaded with the identified eUICC

The ISD-R key components SHALL be ciphered using methods agreed in section 2.8.

The metadata describing the ciphering MAY be transported as AdditionalProperties in the EIS, or MAY be agreed out of band.

This function may return:

    A ‘Function execution status’ with ‘Executed-Success’ indicating that the registration
     function has been successfully executed on the SM-SR as requested by the function
     caller.
    A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
     5.1.6.4
    A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
     section 5.1.6.4 or a specific status code as defined in the table below.

Additional input data:

Input data name                                Description                                    Type   No. MOC
                  This is the eUICC Information Set of the eUICC.
EIS               See         section       5.1.1.2       for      type        description.   EIS    1-N   M
                  The list of EIS data fields that SHALL be included is defined in Annex E.

Table 119: Register EIS Additional Input Data

Specific status codes

Subject               Reason
            Subject                Reason                                         Description
 code                  code
                                             Indicates that the EIS identified by this EID, is already register within the EIS
                           Related    Object database of the SM-SR
8.1.1    EID        3.6    Exists
8.6     EIS                                     During the verification of the EIS signature, an error occurred.
                   6.1    Verification failed
                                                During the consistency review of the EIS data, an error was found (for
8.6     EIS                                     example free memory is bigger than full memory)
                   2.1    Invalid

Table 120: Register EIS Specific Status Codes

5.2.2 Update EIS AdditionalProperties

Function name: UpdateEISAdditionalProperties

Related Procedures: -

Function group: eUICC Management

Function Provider: SM-SR

Description:

This function allows an eUICC Manufacturer (EUM) to update the AdditionalProperties field within the EIS in an identified SM-SR information database. The only field that is updated is “gsma.ESIM.updatedPlatformVersion”, the others remain unchanged.

The AdditionalProperties field is defined in Table 109.

This function may return:

      A ‘Function execution status’ with ‘Executed-Success’ indicating that the update
       function has been successfully executed on the SM-SR as requested by the function
       caller.
      A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
       5.1.6.4
      A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
       section 5.1.6.4 or a specific status code as defined in the table below.

Additional input data:

Input data name                             Description                                       Type                 No. MOC
                      Identification of the targeted eUICC.
eid                                                                                             EID                 1   M
                      See section 5.1.1.1 for type description.
AdditionalProperties This is the EIS field as described in section 5.1.1.2.10.          AdditionalProperties        1   M

Table 522-A: Update AdditionalProperties Additional Input Data

Specific status codes

Subj ect                Reason
             Subj ect               Reason      Description
code                    code
                                               Indicates that the EID is unknown to the function provider
8.1.1       EID          1.1       Unknown
1.6        Function     2.1       Invalid     Indicates that it is not allowed to update an additional property in the input data

Table 522-B: Update AdditionalProperties Specific Status Codes

5.3 ES2 (Operator – SM-DP) Interface Description

5.3.1 Getting eUICC Information

Function name: GetEIS

Related Procedures: Profile Download and Installation

Function group: Profile Management

Function Provider: SM-DP

Description: This function allows the Operator to retrieve up to date the EIS information. The SM-DP SHALL forward the function request to the SM-SR “ES3.GetEIS” as defined in section 5.4.1.

Additional input data:

Input data name                                      Description                                   Type    No. MOC
                  Identification of the targeted eUICC to be audited.
eid                                                                                            EID     1       M
                  See section 5.1.1.1 for type description.
smsr-id           Identification of the SM-SR currently in charge of eUICC management.         OID     1       M
                  This information may change during the eUICC’s lifetime.

Table 121: Get EIS Additional Input Data

Additional output data:
        Output data name                                       Description                                    Type    No. MOC
                         The relevant eUICC Information Set of the eUICC
eis                      See section 5.1.1.1 for type description.                                     EIS       1   M
                         The list of EIS data fields that SHALL be included is defined in Annex E.

Table 122: Get EIS Additional Output Data

Specific status codes

In addition to those returned by ES3.GetEIS, this function may return:
Subj ect                 Reason
              Subj ect              Reason                                            Description
 code                    code
                                    Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose
8.7        SM-SR 3.9      Unknown
                                    address cannot be solved by the SM -DP

Table 123: Get EIS Specific Status Codes

5.3.2 Download a Profile

Function name: DownloadProfile

Related Procedures: Profile Download and Installation

Function group: Profile Management

Function Provider: SM-DP

Description: This function allows the Operator to request that the SM-DP downloads a Profile, identified by its ICCID, via the SM-SR identified by the Operator on the target eUICC, the eUICC being identified by its EID.

Function flow

Upon reception of the function request, the SM-DP SHALL perform the following minimum set of verifications:

      
      The SM-DP SHALL verify it is responsible for downloading and installation of the
      Profile
The SM-DP MAY provide additional verifications.

In case one of these conditions is not satisfied, the SM-DP SHALL refuse the function request and return a ‘Function execution status’ indicating ‘Failed’ with the relevant status code (see table below).

The SM-DP SHALL perform/execute the function according to the Profile Download and Installation procedure described in section 3.1.

This function may return:

   A ‘Function execution status’ with ‘Executed- Success’ indicating that the function has
    been successfully executed by the function provider as requested by the function
    caller.
   A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
    5.1.6.4 indicating that the Profile has not been downloaded before the expiration of
    the specified Validity Period.
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
    section 5.1.6.4 or a specific status code as defined in the table below, indicating that
    the Profile has not been downloaded.
   A ‘Function execution status’ indicating ‘Executed_WithWarning’ indicating that the
    Profile has been downloaded successfully, but the optional Enable has failed or
    expired. In this case, the Status Code and if available, the eUICCResponseData are
    the ones reported by ES3.EnableProfile.

Additional input data:

Input data name                                       Description                                  Type      No. MOC
                 Identification of the target eUICC.
eid                                                                                            EID       1   M
                 See section 5.1.1.1 for type description.
smsr-id          Identification of the SM-SR currently in charge of eUICC management.          OID       1   M
                 This information may change during the eUICC's lifetime.
profileType      Identification of the Profile type to download and install in the eUICC.     String     1   C
                 Identification of the Profile to download and install.
iccid                                                                                          ICCID     1   C
                 See section 5.1.1.1 for type description.
enableProfile    Indicates if the Profile SHALL be enabled after downloading and installation. BOOLEAN   1   M

Table 124: Download Profile Additional Input Data

NOTE:Operator can either provide ICCID or the Profile type. In case the Profile type is provided, the SM-DP is free to select one of the Profiles that matches the Profile type.

Additional output data:

Output data name                                        Description                                         Type     No. MOC
iccid                  Indicates the Profile ICCID that has been downloaded and installed                    ICCID     1         C
                  Contains the detailed error returned by the eUICC in case the function execution Hex
euiccResponseData failed on eUICC. The response data is defined in ES5 depending of the requested                      1     O
                  function.                                                                        binary

Table 125: Download Profile Additional Output Data

Specific status codes

In addition to the Status Codes returned by ES3.EnableProfile, this function can return:

Subj ect               Reason
            Subj ect                    Reason                                        Description
 Code                   code
                                                        Indicates that the eUICC, identified by this EID, is unknown to the
8.1.1      EID         3.9       Unknown
                                                        SM-SR.
           Profile                                      Indicates that the Profile, identified by this iccid is unknown to the
8.2.1                  3.9       Unknown
           ICCID                                        SM-DP.
           Profile               Not Allowed            Indicates that the function caller is not allowed to perform this
8.2.1                  1.2
           ICCID                 (Authorisation)        function on the target Profile.
           Profile                                      Indicates that the Profile type identified by this profileType is
8.2.5                  3.9       Unknown
           Type                                         unknown to the SM-DP.
           Profile               Not Allowed            Indicates that the function caller is not allowed to perform this
8.2.5                  1.2
           Type                  (Authorisation)        function on the ProfileType.
                                                        Indicates that the SM-SR, identified by this smsr-id, is unknown to or
8.7        SM-SR       3.9       Unknown
                                                        whose address cannot be resolved by the SM -SR

Table 126: Download Profile Specific Status Codes

5.3.3 Updating the Policy Rules of a Profile

Function name: UpdatePolicyRules

Related Procedures: -

Function group: Profile Management

Function Provider: SM-DP

Description: This function allows the Operator to update POL2 of a Profile, identified by its ICCID, and installed on an eUICC identified by its EID.

The SM-DP SHALL forward this function request to the identified SM-SR by calling the ES3.UpdatePolicyRules function as defined in section 5.4.6.

Additional input data:

Input data name                                     Description                            Type    No. MOC
                    Identification of the targeted eUICC.
eid                                                                                        EID     1    M
                    See section 5.1.1.1 for type description.
                    Identification of the Profile
iccid                                                                                      ICCID   1    M
                    See section 5.1.1.1 for type description.
smsr-id                                                                                    OID     1    M
                    Identification of the SM-SR currently in charge of eUICC management.
                    This information may change during the eUICC’s lifetime.
                    List of POL2 rules associated with the identified Profile.
pol2                                                                                       POL2    1    M
                    See section 5.1.1.2 for type description.

Table 127: Update Policy Rules Additional Input Data

Additional output data:

None

Specific status codes

In addition to those returned by ES3.UpdatePolicyRules, this function may return:

Subj ect                 Reason
              Subj ect            Reason                                         Description
 code                    code
8.7      SM-SR          3.9     Unknown Indicates that the SM -SR, identified by this smsr-id, is unknown to or whose
                                        address cannot be solved by the SM -DP

Table 128: Update Policy Specific Status Codes

5.3.4 Updating eUICC Information

Function name: UpdateSubscriptionAddress

Related Procedures: Profile Download and Installation, Profile Enabling, Profile Enabling via SM-DP

Function group: Profile Management

Function Provider: SM-DP

Description: This function enables the caller to update the Subscription Address for a Profile in the eUICC Information Set (EIS) of a particular eUICC identified by the EID and ICCID. The Subscription Address is the identifier, such as MSISDN and/or IMSI, through which the eUICC is accessible from the SM-SR via the mobile network when the Profile is in Enabled state. The function replaces the content of the Subscription Address. For consist ency within the system, it is the responsibility of the caller to ensure that all data is provided. The SM- DP SHALL forward the function request to the SM-SR “ES3.UpdateSubscriptionAddress” as defined in section 5.4.7.

Additional input data:

Input data name                                   Description                                     Type           No. MOC
                               Identification of the targeted eUICC to be updated.
eid                                                                                                      EID            1    M
                               See section 5.1.1.1 for type description.
                               Identification of the target Profile.
iccid                                                                                                  ICCID            1    M
                               See section 5.1.1.1 for type description.
                                                                                                    Subscription
newSubscriptionAddress The new Subscription Address                                                                     1    M
                                                                                                      Address
smsr-id                        Identification of the SM -SR currently in charge of eUICC                 OID            1    M
                               management.
                               This information may change during the eUICC’s lifetime.

Table 129: Update Subscription Address Additional Input Data

This function has no additional output data.

Specific status codes

In addition to those returned by ES3.UpdateSubscriptionAddress, this function may return:
Subj ect               Reason
            Subj ect              Reason                                         Description
 code                   code
                                              Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose
8.7         SM-SR 3.9             Unknown
                                              address cannot be resolved by the SM -DP

Table 130: Update Subscription Address Specific Status Codes

5.3.5 Profile Enabling

Function name: EnableProfile

Related Procedures: Profile Enabling via SM-DP

Function group: Platform Management

Function Provider: SM-DP

Description:

This function allows the Operator owner of the Profile to request a SM-DP to enable a Profile in a specified eUICC, eUICC being identified by its EID.

The SM-DP receiving this request SHALL process it according to the “Profile Enabling via SM-DP” procedure described in the section 3.3 of this specification.

This function may return:

    A ‘Function execution status’ with ‘Executed- Success’ indicating that the Profile has
     been enabled on the eUICC.
    A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
     5.1.6.4
A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
section 5.1.6.4 or a specific status code as defined in the table here after.

Additional input data:

Input data name                                   Description                                   Type     No.   MOC
eid                 Identification of the targeted eUICC.                                        EID      1      M
                    See section 5.1.1.1 for type description.
smsr-id              Identification of the SM-SR currently in charge of eUICC management.
                                                                                                 OID       1      M
                     This information may change during the eUICC’s lifetime.
                     Identification of the Profile to enable.
iccid                                                                                           ICCID      1      M
                     See section 5.1.1.1 for type description.

Table 131: Enable Profile Additional Input Data

Additional output data:

       None

Specific status codes

Subj ect                  Reason
               Subj ect                  Reason                                         Description
 code                     code
                                                          Indicates that the eUICC, identified by this EID, is unknown to the SM -
 8.1.1        EID          3.9     Unknown                SR.
                                                        Indicates that the profile change procedure couldn’t complete after
8.2         Profile      5.1     Inaccessible           enabling the target profile, and the profile change was rolled-back on
                                                        the eUICC,
             Profile                                     Indicates that the Profile identified by this ICCID is unknown to the SM-
8.2.1                     3.9     Unknown
             ICCID                                       SR.
                                                         Indicates that the Profile identified by this ICCID is known to the SM -SR
             Profile
8.2.1                     3.4     Invalid destination    but installed on another eUICC than the one identified by the function
             ICCID
                                                         caller.
             Profile
8.2.1                     3.5     Invalid Transition     Indicates that the Profile was already Enabled
             ICCID
             Profile              Not         Allowed Indicates that the function caller is not allowed to perform this function
8.2.1                     1.2
             ICCID                (Authorisation)     on the target Profile.
8.2.2        POL1         3.8     Refused                The POL1 of the impacted Profiles doesn’t allow this operation.
8.2.3        POL2         3.8     Refused                The POL2 of the impacted Profiles doesn’t allow this operation.
8.4         ISD-R        4.2     Execution error        Error during execution of the enabling command on the eUICC.
                                                        Indicates that the SM -SR, identified by this smsr-id, is unknown to or
8.7         SM-SR        3.9     Unknown
                                                        whose address cannot be resolved by the function provider.

Table 132: Enable Profile Specific Status Codes

5.3.6 Profile Disabling

Function name: DisableProfile

Related Procedures: Profile Disabling via SM-DP

Function group: Platform Management

Function Provider: SM-DP

Description: This function allows the Operator owner of the Profile to request an SM-DP to disable the Profile in a specified eUICC; eUICC being identified by its EID.

The SM-DP receiving this request SHALL process it according to Profile Disabling via SM- DP procedure described in section 3.5 of this specification.

This function may return:

      A ‘Function execution status’ with ‘Executed-Success’ indicating that the Profile has
       been disabled on the eUICC.
   A ‘Function execution status’ with ‘Executed-WithWarning’, with a status code as
       defined in section 5.4.9, indicating that the Profile has been disabled on the eUICC,
       and deleted after application of a POL1 or POL2 rule.
   A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
       5.1.6.4
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
       section 5.4.9 or a specific status code as defined in the table here after
Additional input data:
Input data name                                    Description                             Type    No. MOC
                    Identification of the targeted eUICC.
eid                                                                                        EID     1     M
                    See section 5.1.1.1 for type description.
smsr-id             Identification of the SM-SR currently in charge of eUICC management.   OID     1     M
                    This information may change during the eUICC’s lifetime.
                    Identification of the Profile to disable.
iccid                                                                                      ICCID   1     M
                    See section 5.1.1.1 for type description.

Table 133: Disable Profile Additional Input Data

Additional output data:

None

Specific status codes

Subj ect                Reason
             Subj ect             Reason                                       Description
 code                    code
                                          Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose address
8.7          SM-SR      3.9       Unknown cannot be solved by the SM-SR

Table 134: Disable Profile Specific Status Codes

5.3.7 Delete a Profile

Function name: DeleteProfile

Related Procedures: Profile and ISD-P Deletion

Function group: Platform Management

Function Provider: SM-DP

Description: This function allows the Operator to request deletion of the target ISD-P with the Profile to the SM-DP; eUICC being identified by its EID. The SM-DP SHALL forward the function request to the SM-SR “ES3.DeleteISDP” as defined in section 5.4.10.

Additional input data:

Input data name                                     Description                                Type    No. MOC
                     Identification of the targeted eUICC.
Eid                                                                                             EID     1     M
                     See section 5.1.1.1 for type description.
                     Identification of the Profile to disable.
iccid                                                                                          ICCID    1     M
                     See section 5.1.1.1 for type description.
                     Identification of the SM-SR currently in charge of eUICC management.
smsr-id                                                                                         OID     1     M
                     This information may change during the eUICC’s lifetime.

Table 135: Delete Profile Additional Input Data

Additional output data:

None

Specific status codes

In addition to those returned by ES3.DeleteISDP, this function may return:
Subj ect              Reason
           Subj ect              Reason                                         Description
 code                 code
                                             Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose
8.7           SM-SR 3.9         Unknown
                                             address cannot be resolved by the SM -DP

Table 136: Delete Profile Specific Status Codes

5.3.8 Notify a Profile is Disabled

Function name: HandleProfileDisabledNotification

Related Procedures: Profile Download and Installation, Profile Enabling via SM-DP, Profile Enabling, Fall-Back Activation Procedure, Profile Enabling via M2MSP, Profile Disabling via M2MSP

Function group: Platform Management

Notification handler/recipient: Operator

Description:

This function SHALL be called to notify that the Profile identified by its ICCID has been disabled on the eUICC identified by its EID. It is assumed that the ICCID is enough for the SM-DP to retrieve the Operator to notify. This notification also conveys the date and time specifying when the operation has done.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
        Input data name                               Description                                Type      No. MOC
                       Identification of the targeted eUICC.
eid                                                                                         EID         1   M
                       See section 5.1.1.1 for type description.
                       Identification of the Profile that has been disabled.
iccid                                                                                       ICCID       1   M
                       See section 5.1.1.1 for type description.
                       Indication of the date/time when the operation has been performed.
completionTimestamp                                                                         DATETIME 1      M
                       See section 5.1.1.1 for type description.

Table 137: Handle Profile Disabled Notification Additional Input Data

5.3.9 Notify a Profile Enabling

Function name: HandleProfileEnabledNotification

Related Procedures: Profile Disabling and Profile Disabling via SM-DP, Profile Download and Installation, Fall-Back Activation Procedure, Profile Enabling via M2MSP, Profile Disabling via M2MSP

Function group: Platform Management

Notification handler/recipient: Operator

Description:

This function SHALL be called to notify that the Profile identified by its ICCID has been enabled on the eUICC identified by its EID. It is assumed that the ICCID is sufficient for the SM-DP to retrieve the Operator to notify.

This notification also conveys the date and time specifying when the operation has been done. What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:

Input data name                                   Description                                     Type      No. MOC
                       Identification of the targeted eUICC.
eid                                                                                                 EID       1       M
                       See section 5.1.1.1 for type description.
                       Identification of the Profile that has been enabled.
iccid                                                                                               ICCID     1       M
                       See section 5.1.1.1 for type description.
                       Indication of the date/time when the operation has been performed.
completionTimestamp                                                                            DATETIME       1       M
                       See section 5.1.1.1 for type description.

Table 138: Handle Profile Enabled Notification Additional Input Data

5.3.10 Notify a SM-SR Change

Function name: HandleSMSRChangeNotification

Related Procedures: SM-SR Change

Function group: eUICC Management

Notification handler/recipient: Operator

Description: This function SHALL be called for notifying each Operator owning a Profile hosted in the eUICC, identified by its EID, that the SM-SR has changed. The notification is sent by the new SM-SR to the SM-DP, which route this notification to the Operator.

This notification also conveys the date and time specifying when the operation has been done.

This notification is not related to a particular Profile. It is up to the notification recipient to perform any action related to each Profile that is deployed on this eUICC.

Additional input data:

Input data name                                          Description                                        Type       No. MOC
                          The relevant part of the eUICC Information Set linked with the Operator
                          owning the Profile hosted in the eUICC.
eis                                                                                                          EIS        1       M
                          See          section         5.1.1.1     for        type         description.
                          The list of EIS data fields that SHALL be included is defined in Annex E.
                    Indication of the date/time when the operation has been performed.
completionTimestamp See section 5.1.1.1 for type description.                                              DATETIME      1       M

Table 139: Handle SM -SR Change Notification Additional Input Data

No output data is expected in response to this notification.

5.3.11 Notify a Profile Deletion

Function name: HandleProfileDeletedNotification

Related Procedures: Profile Enabling, Profile Enabling via SM-DP, Profile Enabling via M2M SP, Profile DIsabling via M2M SP, Profile and ISD-P Deletion via M2M SP

Function group: Platform Management

Notification handler/recipient: Operator

Description: This function SHALL be called to notify that the Profile identified by its ICCID has been deleted on the eUICC identified by its EID.

This notification also conveys the date and time specifying when the operation has be en done. What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
       Input data name                                  Description                               Type        No. MOC
                       Identification of the targeted eUICC.
eid                                                                                            EID           1       M
                       See section 5.1.1.1 for type description.
                       Identification of the Profile that has been deleted.
iccid                                                                                         ICCID          1       M
                       See section 5.1.1.1 for type description.
                       Indication of the date/time when the operation has been performed.
completionTimestamp                                                                          DATETIME        1       M
                       See section 5.1.1.1 for type description.

Table 140: Handle Profile Deleted Notification Additional Input Data

5.3.12 Auditing eUICC Information

Function name: AuditEIS

Related Procedures: Profile Download and Installation

Function group: Profile Management

Function provider: SM-DP

Description: This function allows the Operator to retrieve the up to date information for the Operator’s Profiles. The SM-DP SHALL forward the request to the SM-SR.

Additional input data:

Input data name                                  Description                              Type     No.       MOC
                  Identification of the targeted eUICC.to be audited
eid                                                                                       EID      1         M
                  See section 5.1.1.1 for type description.
                  Identification of the SM-SR currently in charge of eUICC management.
smsr-id                                                                                   OID      1         M
                  This information may change during the eUICC’s lifetime.
iccid-list        List of “iccid” identifying Profiles to be audited                      ICCID 1..N         C

Table 5312-A: AuditEIS Additional Input Data

If no list of ICCIDs is provided, it is implied that all the EIS data for the Profiles owned by the requesting Operator is required.

Additional output data:

Output data                                           Description                                             Type   No. MOC
  name
                For the relevant eUICC Information Set see section 5.1.1.1 for type description. The list of
                EIS data fields that SHALL be included as defined in Annex E.
Eis             Only the data for the requested Profiles are returned within the EIS. The Profiles that do     EIS    1    C
                not belong to the requestor are not included in the response.
                See section 5.4.2 for considerations on data filtering by the SM -SR.

Table 5312-B: AuditEIS Additional Output Data

Specific status codes

In addition to the status codes returned by ES3.AuditEIS, this function may return the following status codes:

Subj ect                Reason
            Subj ect                  Reason                                         Description
 code                     code
                                                 Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose address
  8.7       SM-SR          3.9       Unknown
                                                 cannot be resolved by the SM -DP

Table 5312-C: AuditEIS Additional Specific Status Codes

5.3.13 Setting Authorisations of M2M -SP to Access Profiles

Function name: SetPLMA

Related Procedures: Set Profile Lifecycle Management Authorisations via SM-DP

Function group: Profile Management

Function Provider: SM-DP

Description:

This function allows the Operator owning Profiles to grant PLMAs to an M2M SP to perform certain operations, or receive certain notifications, related to Profiles, identified by a Profile Type.

The SM-DP receiving this request SHALL forward it to the SM-SR indicated by the Operator, according to procedure “Set Profile Lifecycle Management Authorisations via SM-DP” described in section 3.3.2 of this specification.

This function may return:

   A ‘Function execution status’ with ‘Executed- Success’ indicating that the
    authorisations have been configured in the SM-SR.
   A ‘Function execution status’ with ‘Executed-WithWarning’ with a specific status code
    as defined in the table below, indicating that the authorisations have been configured
        in the SM-SR but that some side-effects of this configuration may require the
        attention of the Operator.
       A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
        section 5.1.6.4 or a specific status code as defined in the table below.

Additional input data:

Input data name                                       Description                                    Type   No.   MOC
plma                   The specification of the PLMA, and the criteria on which this PLMA applies.
                                                                                                     PLMA   1      M
                       See section 5.1.1.2.14 for type description.
                      Identification of the SM-SR on which to apply the PLMA.
smsr-id                                                                                              OID    1      M

Table 5313-A: Set PLMA Additional Input Data

Additional output data:

       None

Specific status codes

In addition to the Status codes returned by ES3.SetPLMA, this function can return the following status codes

Subj ect               Reason
            Subj ect            Reason                                         Description
 code                  code
                                        Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose address
  8.7       SM-SR       3.9     Unknown cannot be resolved by the function provider.

Table 5313-B: Set PLMA Specific Status Codes

5.3.14 Retrieving Authorisations of M2M SP to Access Profiles

Function name: GetPLMA

Related Procedures: Retrieve Profile Lifecycle Management Authorisations by Operator

Function group: Profile Management

Function Provider: SM-DP

Description:

This function allows the Operator owner of Profiles to retrieve a list of PLMAs applicable to a certain Profile, or a certain Profile Type, or for a certain M2M SP.

The same function can also be used by the Operator playing the role of an M2M SP, to retrieve the list of PLMAs granted to this Operator, and applicable to a certain Profile, or a certain Profile Type, owned by another Operator.

The SM-DP receiving this request SHALL forward it to the SM-SR indicated by the Operator, according to procedure “Retrieve Profile Lifecycle Management Authorisations via SM-DP” described in section 3.3.4 of this specification.

This function may return:

       A ‘Function execution status’ with ‘Executed- Success’, and additional output data
        providing the PLMAs.
       A ‘Function execution status’ with ‘Executed-WIthWarning’, to indicate that the result
        was truncated, plus additional output data providing part of the list of applicable
        PLMAs.
       A 'Function execution status' indicating 'Failed' with a status code as defined in section
        5.1.6.4 or a specific status code as defined in the table below.

Additional input data:

Input data name                                         Description                                    Type     No.   MOC
                        Identification of the Profile type for which PLMAs are searched
profileType                                                                                             String   1     C
                        Identification of the M2M SP for which PLMAs are searched
m2m-sp-id                                                                                                OID     1     C
iccid                   Identification of one specific Profile for which PLMAs are searched
                                                                                                        ICCID    1     C
                        Identification of the Operator owning the Profiles to be matched (this input
mno-id                                                                                                   OID     1     C
                        datum SHALL be present only in case the search criterion is a Profile Type).

See section 5.1.1.1 for type description.

smsr-id                 Identification of the SM-SR from which to retrieve the PLMAs.
                                                                                                         OID     1     M
                        This information may change during the eUICC's lifetime.

Table 5314-A: GetPLMA Additional Input Data

One and only one of the input data profileType, m2m-sp-id and iccid SHALL be present.

Additional output data:

Output data name                        Description                       Type   No.   MOC
                      The list of PLMAs that match the search criterion
plma                                                                      PLMA   N      M
                      See section 5.1.1.2.14 for type description.

Table 5314-B: GetPLMA Additional Output Data

Specific status codes

In addition to the Status codes returned by ES3.GetPLMA, this function can return the following Status Codes

Subj ect               Reason
            Subj ect             Reason                                        Description
 code                  code
                                   Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose address
8.7      SM-SR     3.9     Unknown cannot be resolved by the function provider.

Table 5313-C: GetPLMA Specific Status Codes

5.3.15 Notify a Profile Download

Function name: HandleProfileDownloadNotification

Related Procedures: Profile Download

Function group: Profile Management

Notification handler/recipient: Operator (in the role of an M2M SP)

Description: This function SHALL be called to notify an Operator (acting as an M2M SP from the point of view of another Operator) that the Profile identified by its ICCID has been downloaded on the eUICC identified by its EID.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure ‘completionTimestamp’ to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:

Input data name                               Description                                 Type     No. MOC
                        Identification of the targeted eUICC.
eid                                                                                            EID      1     M
                        See section 5.1.1.1 for type description.
                        Identification of the Profile that has been downloaded.
iccid                                                                                         ICCID     1     M
                        See section 5.1.1.1 for type description.
                        Indication of the date/time when the operation has been performed.
completionTimestamp                                                                          DATETIME   1     M
                        See section 5.1.1.1 for type description.

Table 5315: Handle Profile Downloaded Notification Additional Input Data

5.3.16 Notify the Change of Policy Rules of a Profile

Function name: HandlePolicyRulesUpdatedNotification

Related Procedures: POL2 Update, POL2 Update Via SM-DP

Function group: Profile Management

Notification handler/recipient: Operator (in the role of an M2M SP)

Description: This function SHALL be called to notify an Operator (acting as an M2M SP from the point of view of another Operator) that the Policy Rules have been updated on the Profile identified by its ICCID on the eUICC identified by its EID.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure ‘completionTimestamp’ to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:

Input data name                                    Description                                   Type     No. MOC
                      Identification of the targeted eUICC.
Eid                                                                                                EID      1    M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile whose POL2 has been updated.
iccid                                                                                             ICCID     1    M
                      See section 5.1.1.1 for type description.
                      Value of the POL2 after being updated by the Operator owning the Profile
Pol2                                                                                              POL2      1    M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                              DATETIME   1    M
                      See section 5.1.1.1 for type description.

Table 5316: Handle Policy Rules Updated Notification Additional Input Data

5.3.17 Notify a PLMA Setting

Function name: HandleSetPLMANotification

Related Procedures: Set Profile Lifecycle Management Authorisation, Set Profile Lifecycle Management Authorisation via SM-DP

Function group: Platform Management

Notification handler/recipient: Operator (acting in the role of an M2M SP)

Description: This function SHALL be called to notify an Operator (acting as an M2M SP from the point of view of another Operator) that a PLMA concerning this M2M SP has been set or updated.

This notification also conveys the date and time specifying when the operation has been done. In case of multiply handlers are served the SM-SR SHOULD ensure ‘completionTimestamp’ to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
  Input data name                                     Description                                   Type     No. MOC
plma                   The specification of the PLMA that now applies on a Profile Type.            PLMA      1   M
                       Information about the Profile Type are contained in the PLMA structure.
                       See section 5.1.1.2.14 for type description.
completionTimestamp                                                                               DATETIME    1   M
                       Indication of the date/time when the operation has been performed.

See section 5.1.1.1 for type description.

Table 5317: Handle PLMA Setting Notification Additional Input Data

5.3.18 Setting Operator Configuration to Receive Notifications

Function name: SetONC

Related Procedures: Set Operator Notifications Configuration via SM-DP

Function group: Profile Management

Function Provider: SM-DP

Description:

This function allows the Operator to configure for which of its own Profiles, associated with a Profile Type, it wants to receive which kind of status change notifications; whatever the origin of the status change is.

The SM-DP receiving this request SHALL forward it to the SM-SR indicated by the Operator, according to procedure “Set Operator Notifications Configuration via SM-DP” described in section 3.21.2 of this specification.

This function may return:

      A ‘Function execution status’ with ‘Executed- Success’ indicating that the notifications
       configuration has been configured in the SM-SR.
   A ‘Function execution status’ with ‘Executed-WithWarning’ with a specific status code
       as defined in table 5318-C, indicating that the authorisations have been configured in
       the SM-SR but that some side-effects of this configuration may require the attention
       of the Operator.
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
       section 5.1.6.4 or a specific status code as defined in the table here after.
Additional input data:
Input data name                                  Description                                   Type   No.   MOC
onc               The specification of the ONC, and the criterion on which this ONC applies.   ONC    1     M
                  See section 5.1.1.2.15 for type description.
smsr-id           Identification of the SM-SR on which to apply the ONC.
                                                                                               OID    1     M

Table 5318-A: SetONC Additional Input Data

Additional output data:

     None

Specific status codes

In addition to the Status codes returned by ES3.SetONC, this function can return the following Status Codes

Subj ect               Reason
            Subj ect            Reason                                          Description
 code                  code
                                        Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose address
  8.7       SM-SR       3.9     Unknown cannot be resolved by the function provider.

Table 5318-C: SetONC Specific Status Codes

5.3.19 Retrieving Operator Notification Configuration

Function name: GetONC

Related Procedures: Retrieve Operator Notifications Configuration via SM-DP

Function group: Profile Management

Function Provider: SM-DP

Description:

This function allows the Operator to retrieve a list of status change notifications it does not want to receive for its own Profiles, associated with a Profile Type.

The SM-DP receiving this request SHALL forward it to the SM-SR indicated by the Operator, according to procedure “Retrieve Operator Notifications Configuration via SM-DP” described in section 3.21.4 of this specification.

This function may return:

       A ‘Function execution status’ with ‘Executed- Success’, and additional output data
        providing the configured ONC.
       A ‘Function execution status’ with ‘Executed-WithWarning’ with a specific status code
        as defined in table 5319-C, indicating that the authorisations have been configured in
        the SM-SR but that some side-effects of this configuration may require the attention
        of the Operator, and additional output data providing the configured ONC.
       A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
        section 5.1.6.4 or a specific status code as defined in the table here after.

Additional input data:

Input data name                                        Description                                 Type     No.   MOC
profileType           Identification of the Profile Type for which the ONC is searched
                                                                                                   String   1      C
                      Identification of one specific Profile for which the ONC is searched
iccid                                                                                              ICCID    1      C
smsr-id               Identification of the SM-SR from which to retrieve this ONC.
                                                                                                    OID     1      M
                      This information may change during the eUICC's lifetime.

Table 5319-A: GetONC Additional Input Data

One and only one of the input data profileType or iccid SHALL be present.

Additional output data:

  Output
                                                    Description                                          Type   No. MOC
data name
               The ONC including the list of unwanted notifications that match the search criterion
               See section 5.1.1.2.15 for type description.
               NOTE:
onc            If no Operator Notification Configuration has yet been set in the SM -SR for a given      ONC    N    M
               Profile Type, then the output data of this function will list no notification names, as
               all notifications will be sent for Profiles assigned with this Profile Type. See also
               section 3.21.4 and table 511215-A for details.

Table 5319-B: GetONC Additional Output Data

Specific status codes

In addition to the list of status codes returned by ES3.GetONC, this function may return the following list of status codes:

Subj ect               Reason
            Subj ect             Reason                                           Description
 code                  code
8.7       SM-SR       3.9     Unknown Indicates that the SM-SR, identified by this smsr-id, is unknown to or cannot be
                                      resolved by the function provider.

Table 5319-C: GetONC Specific Status Codes

5.3.20 Setting the Emergency Profile Attribute

Function name: SetEmergencyProfileAttribute

Related Procedures: Emergency Profile Attribute Management, Emergency Profile Attribute Management via M2M SP

Function group: Platform Management

Function Provider: SM-DP

Description:

This function allows the Operator owner of the Profile to request an SM-DP to set the Emergency Profile Attribute on a Profile in a specified eUICC, eUICC being identified by its EID.

The SM-DP receiving this request SHALL process it according to the “Emergency Profile Attribute Management” procedure described in the section 3.25 of this specification (option b: via SM-DP).

This function may return:

       A ‘Function execution status’ with ‘Executed- Success’ indicating that the Emergency
        Profile Attribute has been set on the targeted Profile.
       A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
        5.1.6.4
       A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
        section 5.1.6.4 or a specific status code as defined in the table here after.

Additional input data:

Input data name                                       Description                                      Type    No.   MOC
Eid                    Identification of the targeted eUICC.                                           EID     1     M
                       See section 5.1.1.1 for type description.
                      Identification of the SM-SR currently in charge of eUICC management.
smsr-id                                                                                                OID     1     M
                      This information may change during the eUICC’s lifetime.
                      Identification of the Profile on which to set the Emergency Profile Attribute.
iccid                                                                                                  ICCID   1     M
                      See section 5.1.1.1 for type description.

Table 5320-A: Set Emergency Profile Attribute Additional Input Data

Additional output data:

       None

Specific status codes

In addition to the status codes returned by ES3.setEmergencyProfileAttribute, this function may return the following status codes:

Subj ect               Reason
            Subj ect            Reason                                          Description
 Code                  code
8.7       SM-SR       3.9     Unknown Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose address
                                      cannot be resolved by the function provider.

Table 5320-C: Set Emergency Profile Attribute Specific Status Codes

5.3.21 Notifying the Emergency Profile Attribute Setting

Function name: HandleEmergencyProfileAttributeSetNotification

Related Procedures: Emergency Profile Attribute Management, Emergency Profile Attribute Management via M2M SP

Function group: Profile Management

Notification handler/recipient: Operator

Description: This function SHALL be called to notify that the Emergency Profile Attribute has been set on the Profile identified by its ICCID on the eUICC identified by its EID.

This notification also conveys the date and time specifying when the operation has been done. What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
       Input data name                                  Description                                        Type     No. MOC
                        Identification of the targeted eUICC.
eid                                                                                                      EID      1       M
                        See section 5.1.1.1 for type description.
                        Identification of the Profile that has the Emergency Profile Attribute set.
iccid                                                                                                   ICCID     1       C
                        See section 5.1.1.1 for type description.
                        Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                    DATETIME   1       M
                        See section 5.1.1.1 for type description.

Table 5321: Handle Emergency Profile Attribute Set Notification Additional Input Data

5.3.22 Notifying the Emergency Profile Attribute Unsetting

Function name: HandleEmergencyProfileAttributeUnsetNotification

Related Procedures: Emergency Profile Attribute Management, Emergency Profile Attribute Management via M2M SP

Function group: Profile Management

Notification handler/recipient: Operator

Description:

This function SHALL be called to notify that the Emergency Profile Attribute has been unset on the Profile identified by its ICCID, on the eUICC identified by its EID.

This notification also conveys the date and time specifying when the operation has been done. What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
   Input data name                                      Description                                        Type     No. MOC
                        Identification of the targeted eUICC.
Eid                                                                                                        EID         1   M
                        See section 5.1.1.1 for type description.
                        Identification of the Profile that has the Emergency Profile Attribute unset.
Iccid                                                                                                     ICCID        1   M
                        See section 5.1.1.1 for type description.
                        Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                     DATETIME       1   M
                        See section 5.1.1.1 for type description.

Table 5322: Handle Profile Emergency Profile Attribute Unset

5.3.23 Setting the Fall-Back Attribute

Function name: SetFallBackAttribute

Related Procedures: Fall-Back Attribute Management

Function group: Platform Management

Function Provider: SM-DP

Description:

This function allows the Operator owner of the Profile to request an SM-DP to set the Fall- Back Attribute on a Profile in a specified eUICC, eUICC being identified by its EID.

The SM-DP receiving this request SHALL process it according to the “Fall-Back Attribute Management” procedure described in sections 3.28 and 3.29 of this specification.

This function may return:

      A ‘Function execution status’ with ‘Executed- Success’ indicating that the Fall-Back
       Attribute has been set on the targeted Profile.
      A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
       5.1.6.4
      A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
       section 5.1.6.4 or a specific status code as defined in the table here after.

Additional input data:

Input data name                                 Description                                 Type     No.   MOC
eid               Identification of the targeted eUICC.                                      EID     1     M
                  See section 5.1.1.1 for type description.
                  Identification of the SM-SR currently in charge of eUICC management.
smsr-id                                                                                     OID      1     M
                  This information may change during the eUICC’s lifetime.
                  Identification of the Profile on which to set the Fall -Back Attribute.
iccid                                                                                       ICCID    1     M
                  See section 5.1.1.1 for type description.

Table 5323-A: Set Fall-Back Attribute Additional Input Data

Additional output data:

      None

Specific status codes

In addition to the status codes returned by ES3.SetFallBackAttribute, this function may return the following status codes:

Subj ect              Reason
           Subj ect            Reason                                          Description
 Code                 code
                                       Indicates that the SM-SR, identified by this smsr-id, is unknown to or whose address
  8.7      SM-SR       3.9     Unknown cannot be resolved by the function provider.

Table 5323-C: Enable Profile Specific Status Codes

5.3.24 Notifying the Fall-Back Attribute is Set

Function name: HandleProfileFallBackAttributeSetNotification

Related Procedures: Fall-Back Attribute Management, Fall-Back Attribute Management via SM-DP, Fall-Back Attribute Management via M2M SP

Function group: Profile Management

Notification handler/recipient: Operator

Description:

This function SHALL be called to notify that the Fall-Back Attribute has been set on the Profile identified by its ICCID, on the eUICC identified by its EID.

This notification also conveys the date and time specifying when the operation has been done. What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
   Input data name                                      Description                                       Type     No. MOC
                        Identification of the targeted eUICC.
eid                                                                                                      EID      1   M
                        See section 5.1.1.1 for type description.
                        Identification of the Profile on which the Fall-Back Attribute has been set.
iccid                                                                                                   ICCID     1   M
                        See section 5.1.1.1 for type description.
                        Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                    DATETIME   1   M
                        See section 5.1.1.1 for type description.

Table 5324: Handle Profile Fall-Back Attribute Set additional input data

5.3.25 Notifying the Fall-Back Attribute is Unset

Function name: HandleProfileFallBackAttributeUnsetNotification

Related Procedures: Fall-Back Attribute Management, Fall-Back Attribute Management via SM-DP, Fall-Back Attribute Management via M2M SP

Function group: Profile Management

Notification handler/recipient: Operator

Description:

This function SHALL be called to notify that the Fall-Back Attribute has been unset on the Profile identified by its ICCID, on the eUICC identified by its EID.

This notification also conveys the date and time specifying when the operation has been done. What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
  Input data name                                     Description                                 Type     No. MOC
                      Identification of the targeted eUICC.
Eid                                                                                               EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile on which the Fall-Back Attribute has been
                      unset.
Iccid                                                                                            ICCID     1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                             DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 5325: Handle Profile Fall-Back Attribute Unset Additional Input Data

5.4 ES3 (SM-DP – SM-SR) Interface Description

This section describes operations and notifications on the interfaces between the SM-DP and the SM-SR. The SM-DP usually acts on behaf of an Operator. When that is the case, the SM-DP SHALL indicate, in each request sent to the SM-SR, the mno-id identifying the requesting Operator. The way the mno-id is provided by the SM-DP is specified in Annex B.

Similarly, the SM-SR SHALL indicate, in each notification sent to the SM-DP, the mno-id identifying the targeted Operator.

NOTE:The execution of several ES3 functions by the SM-SR is conditioned by the verification that the Operator requesting to perform an operation on a Profile via its SM-DP, or the Operator to be notified via its SM-DP:

o is the owner of the targeted Profile
    or
o is authorised for this operation or notification by the owner of the
  targeted Profile.
The specification of this verification by the SM-SR is described in sections
5.7.1.2 and 5.7.1.3, based on the identities supplied as described above.

5.4.1 Getting eUICC Information

Function name: GetEIS

Related Procedures: Profile Download and Installation

Function group: Profile Management

Function Provider: SM-SR

Description: This function allows the SM-DP, requesting on behalf of an Operator, retrieving the eUICC Information Set (EIS) of a particular eUICC from the SM-SR information database based on the EID.

The SM-DP SHALL indicate on behalf of which Operator it is requesting this operation.

This function may return:

   A ‘Function execution status’ with ‘Executed- Success’ indicating that the download
    function has been successfully executed on the SM-SR as requested by the function
    caller.
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
    section 5.1.6.4 of a specific status code as defined in the table below.

Additional input data:

Input data name                Description                    Type   No. MOC
                  Identification of the targeted eUICC.
eid                                                           EID    1   M
                  See section 5.1.1.1 for type description.

Table 141: Get EIS Additional Input Data

The SM-SR SHALL filter the list of Profiles returned in the EIS, considering the authorisation granted by the Profile owners; for each Profile, this includes:

   If the SM-DP indicates that it is requesting this operation on behalf of the owner of the
    Profile, the SM-SR SHALL include this Profile in the returned EIS.
   If the SM-DP indicates that it is requesting this operation on behalf of an Operator
    that is not the owner of the targeted Profile, the SM-SR SHALL include the Profile in
    the returned EIS only if the Operator owning the Profile has granted a PLMA allowing
    the operation “GetEIS” to the Operator requesting the operation.

Additional output data:

Output data
                                                  Description                                      Type   No. MOC
  name
                  The relevant eUICC Information Set of the eUICC. See section 5.1.1.1 for type
eis               description.                                                                       EIS    1   C
                   The list of EIS data fields that SHALL be included is defined in Annex E.

Table 142: Get EIS Additional Output Data

Specific status codes

Subj ect               Reason
            Subj ect                    Reason                                        Description
 code                   code
 8.1.1      EID         1.1     Unknown                    Indicates that the EID is unknown to the function provider
                              Not               Allowed Function requester is not allowed to manage this EIS, identified by
8.6       EIS         1.2     (Authorisation)           this EID.

Table 143: Get EIS Specific Status Codes

5.4.2 Auditing eUICC Information

Function name: AuditEIS

Related Procedures: Profile Download and Installation

Function group: Profile Management

Function provider: SM-SR

Description: This function allows the SM-DP, requesting on behalf of an Operator, to retrieve up to date EIS information. The SM-SR SHALL use the relevant functions of the ES5 interface to retrieve the information from the eUICC. At the end of the successful execution of this function, the SM-SR SHALL update its EIS database upon the basis of this information.

The SM-DP SHALL indicate on behalf of which Operator it is requesting this o peration.

If the SM-DP provides a list of ICCID of Profiles to audit, the SM-SR SHALL verify for each profile that the Operator, on behalf of which the SM-DP requests this operation,

   is either the owner of the targeted Profile
    or
   is authorised by the Operator owning the targeted Profile(s)

to perform the operation “AuditEIS” on a Profile that matches the criteria of the PLMA (see section 5.7.1.1 for the detail of the matching of the criteria).

This SHALL also be applied if the list of ICCIDs identifies

   Profiles that are owned by this Operator
    and / or
   Profiles that are owned by other Operators.

The SM-SR MAY provide additional verifications.

This function may return:

   A ‘Function execution status’ with ‘Executed- Success’ indicating that the function has
    been successfully executed on the SM-SR as requested by the function caller.
     A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
      5.1.6.4
     A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
      section 5.1.6.4 of a specific status code as defined in the table below.

Additional input data:

Input data name                       Description                        Type   No.   MOC
                   Identification of the targeted eUICC to be audited.
eid                                                                       EID   1     M
                   See section 5.1.1.1 for type description.
iccid-list         List of “iccid” identifying Profiles to be audited    ICCID 1..N   C

Table 144: Audit EIS Additional Input Data

If no list of ICCIDs is provided, it is implied that all authorised Profiles in the EIS are requested.

The SM-SR SHALL filter the list of Profiles returned in the EIS, considering the authorisation granted by the Profile owners; for each Profile, this includes:

     If the SM-DP indicates that it is requesting this operation on behalf of the owner of the
      Profile, the SM-SR SHALL include this Profile in the returned EIS.
     If the SM-DP indicates that it is requesting this operation on behalf of an Operator
      that is not the owner of the targeted Profile, the SM-SR SHALL include the Profile in
      the returned EIS only if the Operator owning the Profile has granted a PLMA allowing
      the operation “AuditEIS” to the Operator requesting the operation.
Additional output data:
          Output data name                                        Description                                   Type   No. MOC
                         The relevant eUICC Information Set of the eUICC
eis                      See section 5.1.1.1 for type description.                                    EIS    1      C
                         The list of EIS data fields that SHALL be included is defined in Annex E.

Table 145: Audit EIS Additional Output Data

Specific status codes
Subj ect                     Reason
                Subj ect                      Reason                                           Description
 Code                           code
                                                               Indicates that the eUICC, identified by this EID, is unknown to the
8.1.1           EID          3.9        Unknown
                                                               function provider
                                                               Indicates that the Profile identified by one of the ICCIDs in the list is
                Profile
8.2.1                        3.4        Invalid destination    known to the function provider but installed on another eUICC than the
                ICCID
                                                               one identified by the function caller.
                                        Not Allowed            One or more Profiles identified by ICCIDs in the list do not belong to
8.2             Profile      1.2
                                        (Authorisation)        function requester
                              Not Allowed         Function requester is not allowed to manage this EIS, identified by this
8.6        EIS         1.2
                              (Authorisation)     EID.
                              Delivered With No   The function execution request has been delivered to remote entity but
1.6        Function    5.4
                              Response            no response is received.

Table 146: Audit EIS Specific Status Codes

5.4.3 Create a New ISD-P in an eUICC

Function name: CreateISDP

Related Procedures: Profile Download and Installation

Function group: Profile Management

Function Provider: SM-SR

Description: This function allows the SM-DP to request the creation of an ISD-P to the SM- SR in charge of the management of the targeted eUICC; eUICC being identified by its EID.

Function flow

Upon reception of the function request, the SM-SR SHALL perform the following minimum set of verifications:

      
     The SM-SR is responsible for the management of the targeted eUICC
      
     The Profile identified by its ICCID is not already present within its EIS database
     (meaning allocated to another ISD-P)
   The requested amount of memory can be satisfied
SM-SR MAY provide additional verifications.

In case one of these conditions is not satisfied, the SM-SR SHALL refuse the function request and return a ‘Function execution status’ indicating ‘Failed’ with the relevant status code (see table below).

The SM-SR receiving this request SHALL process it according to the “Profile Download and Installation” procedure described in the section 3.1 of this specification.

When the SM-SR ends successfully this function it SHALL update the eUICC EIS by adding a new Profile entry in the EIS with following values:

   The iccid value received as parameter
   The isd-p-aid value as allocated by the SM-SR
   The mno-id value received as parameter
   The state value as ‘Created’
   The smdp-id retrieved from the authentication context of the caller
   The Cumulative Granted Non Volatile Memory value received as parameter

NOTE:The initial Subscription Address and the initial POL2 can be set after the Profile is completely downloaded using the “ES3.ProfileDownloadCompleted” function.

This function may return:

   A ‘Function execution status’ with ‘Executed- Success’ indicating that the ISD-P has
    been successfully created on the eUICC as requested by the function caller.
   A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
    5.1.6.4
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
    section 5.1.6.4 or a specific status code as defined in the table below.

Additional input data:

Input data name                                        Description                                            Type         No. MOC
                  Identification of the targeted eUICC.
Eid                                                                                                           EID          1       M
                  See section 5.1.1.1 for type description.
                  Identification of the Profile to download and install.
Iccid                                                                                                        ICCID         1       M
                  See section 5.1.1.1 for type description.
mno-id            The identification of the Operator owning the Profile                                       OID          1       M
RequiredMemory Indicates the Cumulative Granted Non Volatile Memoryallocated to the ISD-P to                 Integer       1       M
               contain the Profile. The value is expected in Bytes.
                  Indicates to the function provider that the function caller has something else to do
                  with the targeted eUICC right after this function execution. This indication MAY be
                  used by the function provider to decide if it has to keep the remote communication
                  channel with the eUICC open (this may be relevant or not, depending on the remote
                  communication channel. This is the case for instance for Remote Administration
                  over HTTPS as defined in section 2.4.4.
moreToDo                                                                                                     Boolean       1       O
                  The only purpose is to optimise resource management and save execution time of
                  the overall procedure. It is up to the function provider to support this feature or not.
                  This input data is optional; if missing the function provider SHALL consider that the
                  function caller has nothing else to do.

Table 147: Create ISD-P Additional Input Data

If the "RequiredMemory" parameter of this ES3.CreateISDP function call is equal to ‘0’, the "Cumulative Granted Non Volatile Memory" parameter SHALL NOT be used in the INSTALL command of the ES5.CreateISDP function.

Additional output data:
Output data name     Description                                                                   Type                No. MOC
                     The AID, allocated by the SM-SR, of the ISD-P
isd-p-aid
                     containing the Profile. The Tar value is included in the                      AID                 1
                                                                                                                               C (see
                     AID. See Annex H “Coding of the PIX for ‘Embedded UICC                                                    note)
                     Remote Provisioning and Management’ (Normative)”.
                  Contains the detailed error returned by the eUICC in case the function
                                                                                                   Hexadecimal
euiccResponseData execution failed on eUICC. The response data is defined in ES8                                       1       O
                                                                                                   string
                  depending of the requested function.

Table 148: Create ISD-P Additional Output Data

NOTE         In case of error or expiration of the function execution, the output data isd -p-
             aid SHOULD be absent.
This output data isd-p-aid was mandatory in version 3.2 and earlier of this
specification. For backward-compatibility with such versions, the SM-SR
MAY send this output data anyway, and the SM-DP SHOULD be ready to
receive this data, even in case of error and expiration. In such a case, the
value of this data is irrelevant, so the SM-SR SHOULD return a value that is
clearly not a valid AID (ex: ‘0000000000’) and the SM-DP SHOULD ignore
the data, whatever the value is.

Specific status codes

Subj ect                  Reason
             Subj ect                 Reason                                       Description
  code                     code
                                                  Indicates that the eUICC, identified by this EID, is unknown to the function
  8.1.1      EID            3.9    Unknown        provider
                                                Indicates that the ICCID is already allocated to another Profile managed by
           Profile
8.2.1                     3.3    Already in use the function provider.
           ICCID
                                                Error during execution of the creation command on the eUICC. In that case,
                                                the output data “euiccResponseData contains the exact response coming
                                 Execution
 8.4       ISD-R          4.2                   from the eUICC.
                                      error
                                               The eUICC has not enough free memory to execute the creation of the new
                                Insufficient   ISD-P with this required amount of memory.
8.1       eUICC          4.8
                                memory

Table 149: Create ISD-P Specific Status Codes

5.4.4 Download a New Profile

Function name: SendData

Related Procedures: Profile Download and Installation

Function group: Profile Management

Function Provider: SM-SR

Description: This function allows the SM-DP to send securely commands defined in ES8 interface (i.e.: Profile download or establish a key set) to an ISD-P or the ISD-R through the SM-SR in charge of the management of the targeted eUICC; eUICC being identified by its EID.

Function flow

Upon reception of the function request, the SM-SR SHALL perform the following minimum set of verifications:

       The SM-SR is responsible for the management of the targeted eUICC.
       The targeted ISD-P (designated in the sd-aid or in the commands) is created on the
        eUICC and is managed by the calling SM-DP.
   If the SM-DP requests to send the commands to the ISD-R: the commands are
    allowed to be executed by ISD-R, including ISD-P key establishment as described in
    section 4.1.3.1.

NOTE1:this verification implies the parsing and analysing of the commands.

NOTE2:this verification allows to prevent the SM-DP to perform arbitrary operations in the ISD-R

The SM-SR MAY provide additional verifications.

In case one of these conditions is not satisfied, the SM-SR SHALL refuse the function request and return a ‘Function execution status’ indicating ‘Failed’ with the relevant status code (see table below).

This function allows sending commands defined in the ES8 interface in several steps. This may be necessary in case of the data is too big compared to eUICC capabilities. It is up to the function caller to determine if it has to handle this situation based on the eUICC capabilities described in EIS.

The SM-SR is free to select the most relevant OTA protocol to communicate up to the eUICC. As a consequence, the data format provided by the function caller SHALL NOT depend of the selected OTA protocol capabilities (for example SM-DP can consider there is no limit on data length). The data provided by the SM-DP SHALL be a list of C-APDU as defined in ETSI TS 102 226 [5] section 5.2.1, or TLV commands as defined in this document, section 4.1.3.3. The SM-SR has the responsibility to build the final Command script, depending on eUICC capabilities and selected protocol:

   by adding the Command scripting template for definite or indefinite length,
   and, if necessary, by segmenting the provided command script into several pieces
   and, if necessary, by adding the relevant Script Chaining TLVs.

Annex K provides a description of heuristics that MAY be used to implement Script Chaining.

This function may return:

   A ‘Function execution status’ with ‘Executed- Success’ indicating that the function has
    been successfully executed by the function provider as requested by the function
    caller.
   A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
    5.1.6.4
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
    section 5.1.6.4 or a specific status code as defined in the table below.
Additional input data:
 Input data
                                                 Description                    Type       No. MOC
   name
eid           Identification of the targeted eUICC.                              EID       1   M

See section 5.1.1.1 for type description.

                 Identification of the SD which SHALL process the commands contained in the
sd-aid                                                                                                     AID         1      M
                 data argument. sd-aid could identify either the ISD-P or the ISD-R.

The data to send into the targeted ISD-P and eUICC.

                 The data SHALL contain a list a C-APDU as defined in ETSI TS 102 226 [5],            Hexadecimal
data             section 5.2.1 or TLV commands as defined in this document, section 4.1.3.3. The                       1      M
                                                                                                         string
                 C-APDU can contain any of the commands defined in ES8 interface. The
                 commands SHALL be secured according to section 2.5.
moreToDo         See section 5.4.3 for description of this input data                                   Boolean        1      O

Table 150: Send Data Additional Input Data

Due to an ambiguity in former version of the specifications, an SM-DP following a former version of this document may send all commands of a Profile download procedure (including ISD-P key establishment commands) pointing the ISD-P as the targeted security domain (argument sd-aid). For backward-compatibility, the SM-SR SHOULD detect such cases, and support them by appropriately sending the commands to the ISD-R or the ISD-P.

Additional output data:
 Output data name                                       Description                                       Type        No. MOC
                  Contains the Random Challenge (RC) in case of the key establishment
                  procedure or the detailed error returned by the eUICC in case of one                Hexadecimal
euiccResponseData                                                                                                      1      C
                  command execution failed on eUICC. The response data is defined in                     string
                  ES8 depending of the requested function.

Table 151: Send Data Additional Output Data

Specific status codes

Subj ect                Reason
           Subj ect                       Reason                                        Description
 code                     code
                                                             Indicates that the eUICC, identified by this EID, is unknown to the
8.1.1      EID          3.9        Unknown                   function provider
           ISD-P-                                            Indicates that the ISD-P identified by this SD-AID is unknown to the
8.3.1                   3.9        Unknown
           AID                                               function provider.
                                                             Error during execution of one command, when error occurs at ISD-P
8.3        ISD-P        4.2        Execution error           level.
           ISD-P-                  Not allowed               Indicates that the function caller is not allowed to execute commands
8.3.1                   1.2
           AID                                               in the targeted ISD-P.
                                   (Authorisation)
                                   Not            allowed Indicates that the function caller is not allowed to execute the
8.4        ISD-R        1.2        (Authorisation)        requested commands in the ISD-R.

Table 152: Send Data Specific Status Codes

5.4.5 Indicating the Profile Download is Completed

Function name: ProfileDownloadCompleted

Related Procedures: Profile Download and Installation

Function group: Profile Management

Function Provider: SM-SR

Description: This function allows the SM-DP to indicate to the SM-SR that the Profile download (identified by its ICCID) has been completed on the eUICC; eUICC being identified by its EID.

This function allows optionally to set a first Subscription Address, typically the MSISDN, and saves it in the EIS, and optionally a first POL2 associated to the newly download Profile. In case no POL2 is provided at that time, it means that the Profile won’t be protected by any POL2 at SM-SR side. But the POL2 MAY be set or updated at any time later using the “UpdatePolicyRules” function defined in section 5.4.6.

The Subscription Address is the identifier, such as MSISDN and/or IMSI, through which the eUICC is accessible from the SM-SR via the mobile network when the Profile is in Enabled state. The Subscription Address MAY be set or updated at any time later using the “UpdateSubscriptionAddress” function defined in section 5.4.7.

On reception of this function request the SM-SR SHALL immediately update the EIS to set the identified Profile:

   (Optional) the provided ProfileType as defined in section 5.1.1.2.4
    (Conditional) the new Subscription Address. If the Profile is to be enabled after it is
    loaded then the Subscription Address becomes mandatory.
   (Optional) the provided POL2

At the end of this function call, the Profile state is “Disabled”. The SM-DP may call the function “ES3.EnableProfile” (see section 5.4.8) to enable the Profile if required by the Operator.

This function may return:

   A ‘Function execution status’ with ‘Executed- Success’ indicating that the function has
    been correctly executed.
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
    section 5.1.6.4 of a specific status code as defined in the table below.

Additional input data:

Input data name                               Description                    Type           No. MOC
                    Identification of the targeted eUICC.
eid                                                                            EID            1   M
                    See section 5.1.1.1 for type description.
                    Identification of the Profile
iccid                                                                         ICCID           1   M
                    See section 5.1.1.1 for type description.
                         Indicates, through an SM-DP reference, the type of Profile
ProfileType                                                                                          String             1       O
                         generated by the SM-DP (for example 3G_16K)
                                                                                               SUBSCRIPTION-
subscriptionAddress The Subscription Address related to the identified Profile                                          1       O
                                                                                                 ADDRESS
pol2                     The POL2 to associate with the identified Profile.                           POL2              1       O

Table 153: Profile Download Completed Additional Input Data

Additional output data:

No additional data

Specific status codes
 Subj ect     Subj ect     Reason        Reason                                       Description
code                      code
8.1.1      EID            3.9        Unknown           Indicates that the eUICC, identified by this EID, is unknown to the
                                                       function provider
8.2.1      Profile        3.9        Unknown           Indicates that the Profile identified by this ICCID is unknown to the
           ICCID                                       function provider.
8.2.1      Profile        3.4        Invalid           Indicates that the Profile identified by this ICCID is known to the
           ICCID                     destination       function provider but installed on another eUICC than the one identified
                                                       by the function caller.
8.2.3      POL2           2.1        Invalid           Indicates that the POL2 is invalid

Table 154: Profile Download Completed Specific Status Codes

5.4.6 Updating the Policy Rules of a Profile

Function name: UpdatePolicyRules

Related Procedures: -

Function group: Profile Management

Function Provider: SM-SR

Description: This function allows the SM-DP authorised by the Operator to update POL2 of a Profile, identified by its ICCID, and installed on an eUICC identified by its EID.

The function can update a Profile in “Disabled” or “Enabled” state and SHALL return an error for any other Profile state.

The function completely replaces the definition of existing POL2. It means that it is the responsibility of the caller to provide the complete definition of POL2.

This function may return:

     A ‘Function execution status’ with ‘Executed- Success’ indicating that the update
      Policy Rules function has been successfully executed by the SM-SR as requested by
      the function caller.
     A ‘Function execution status’ with ‘Expired’ with a status code as defined in sec tion
      5.1.6.4
      A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
      section 5.1.6.4 of a specific status code as defined in the table below.
Additional input data:
                  Input data name                          Description                           Type    No. MOC
                  Identification of the targeted eUICC.
eid                                                                            EID     1    M
                  See section 5.1.1.1 for type description.
                  Identification of the Profile
iccid                                                                          ICCID   1    M
                  See section 5.1.1.1 for type description.
                  List of POL2 rules associated with the identified Profile.
pol2                                                                           POL2    1    M
                  See section 5.1.1.1 for type description.

Table 155: Update Policy Rules Additional Input Data

Table 156: Void

Specific status codes

Subj ect                  Reason
           Subj ect                   Reason                                          Description
 code                      code
                                                    Indicates that the eUICC, identified by this EID, is unknown to the function
 8.1.1     EID             3.9      Unknown
                                                    provider
          Profile                                  Indicates that the Profile identified by this ICCID is unknown to the function
8.2.1                     3.9      Unknown
          ICCID                                    provider.
                                                   Indicates that the Profile identified by this ICCID is known to the function
          Profile                  Invalid
8.2.1                     3.4                      provider but installed on another eUICC than the one identified by the function
          ICCID                    destination
                                                   caller.
8.2.3     POL2            2.1      Invalid         Indicates that the POL2 is invalid.

Table 157: Update Policy Rules Specific Status Codes

5.4.7 Updating eUICC Information

Function name: UpdateSubscriptionAddress

Related Procedures: Profile Download and Installation, Profile Enabling, Profile Enabling via SM-DP

Function group: Profile Management

Function Provider: SM-SR

Description: This function enables the caller to update the Subscription Address for a Profile in the eUICC Information Set (EIS) of a particular eUICC identified by the EID and ICCID. The Subscription Address is the identifier, such as MSISDN and/or IMSI, through which the eUICC is accessible from the SM-SR via the mobile network when the Profile is in Enabled state.

The SM-DP SHALL indicate on behalf of which Operator it is requesting this operation.

The SM-SR SHALL verify that the request is:

    Either sent on behalf of an Operator owning the targeted Profile
     or
    Sent on behalf of an Operator that is not the owner of the targeted Profile, but the
     Operator owning the targeted Profile has granted a PLMA allowing the operation
     “UpdateSubscriptionAddress” to the Operator requesting the operation.

The SM-SR MAY provide additional verifications.

The function replaces the content of the Subscription Address. For consistency within the system, it is the responsibility of the caller to ensure that all data is provided. This function may return:

    A ‘Function execution status’ with ‘Executed- Success’ indicating that the
     UpdateSubscriptionAddress function has been successfully executed by the SM-SR
     as requested by the function caller.
    A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
     section 5.1.6.4 of a specific status code as defined in the table below.
Additional input data:
                 Input data name                 Description                          Type            No. MOC
                        Identification of the targeted eUICC.
eid                                                                         EID            1    M
                        See section 5.1.1.1 for type description.
                        Identification of the target Profile.
iccid                                                                      ICCID           1    M
                        See section 5.1.1.1 for type description.
newSubscriptionAddress The new Subscription Address                 Subscription Address   1    M

Table 158: Update Subscription Address Additional Input Data

Additional output data:

This function has no additional output data:

Specific status codes

Subj ect       Subj ect         Reason             Reason                                      Description
code                              code
                                                                    Indicates that the EIS identified by this EID, is unknown to
8.1.1        EID              1.1          Unknown
                                                                    the function provider
                                                                    Indicates that the Profile identified by the ICCID, is unknown
8.2.1        ICCID            1.1          Unknown
                                                                    to the function provider
             Subscription                  Not Allowed              Function requester is not allowed to manage the
8.2.6                         1.2
             Address                       (Authorisation)          Subscription Address.

Table 159: Update Subscription Address Specific Status Codes

5.4.8 Profile Enabling

Function name: EnableProfile

Related Procedures: Profile Enabling via SM-DP

Function group: Platform Management

Function Provider: SM-SR

Description: This function allows the SM-DP to request a Profile Enabling to the SM-SR in charge of the management of the targeted eUICC; eUICC being identified by its EID.

The SM-DP SHALL indicate on behalf of which Operator it is requesting this operation.

The SM-SR SHALL verify that the request is

   Either sent on behalf of an Operator owning the targeted Profile
    or
   Sent on behalf of an Operator that is not the owner of the targeted Profile, but the
    Operator owning the targeted Profile has granted a PLMA allowing the operation
    “EnableProfile” to the Operator requesting the operation.

The SM-SR MAY provide additional verifications.

The SM-SR receiving this request SHALL process it according to “Profile Enabling via SM- DP” procedure described in the section 3.3 of this specification.

This function may return:

   A ‘Function execution status’ with ‘Executed- Success’ indicating that the Profile has
    been enabled on the eUICC.
   A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
    5.1.6.4
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
    section 5.1.6.4 of a specific status code as defined in the table here after.

Additional input data:

Input data name               Description                  Type     No.    MOC
eid                  Identification of the targeted eUICC.          EID       1      M
                     See section 5.1.1.1 for type description.
                    Identification of the Profile to enable.
iccid                                                              ICCID     1       M
                    See section 5.1.1.1 for type description.

Table 160: Enable Profile Additional Input Data

Additional output data:

Output data name                                       Description                                        Type          No. MOC
                  Contains the detailed error returned by the eUICC in case the function
                                                                                         Hexadecimal
euiccResponseData execution failed on eUICC. The response data is defined in ES8 String                                  1     O
                  depending of the requested function.

Table 161: Enable Profile Additional Output Data

Specific status codes

Subj ect                Reason
           Subj ect                     Reason                                            Description
 code                      code
                                                          Indicates that the eUICC, identified by this EID, is unknown to the function
 8.1.1     EID               3.9   Unknown                provider.
                                                        Indicates that the Profile change procedure couldn’t complete after
8.2      Profile           5.1   Inaccessible           enabling the target Profile, and the Profile change was rolled -back on the
                                                        eUICC,
          Profile                                        Indicates that the Profile identified by this ICCID is unknown to the function
8.2.1                       3.9   Unknown
          ICCID                                          provider.
                                                         Indicates that the Profile identified by this ICCID is known to the function
          Profile
8.2.1                       3.4   Invalid destination    provider but installed on another eUICC than the one identified by the
          ICCID
                                                         function caller.
          Profile
8.2.1                       3.5   Invalid Transition     Indicates that the Profile was already Enabled
          ICCID
          Profile                 Not        Allowed Indicates that the function caller is not allowed to perform this function on
8.2.1                       1.2
          ICCID                   (Authorisation)    the target Profile.
8.2.2     POL1              3.8   Refused                The POL1 of the impacted Profiles doesn’t allow this operation.
8.2.3     POL2              3.8   Refused                The POL2 of the impacted Profiles doesn’t allow this operation.
                                                         No PLMA allows the SM-DP, or the Operator on behalf of which the SM-
8.2.7     PLMA              3.8   Refused
                                                         DP sent the request, to execute this operation.
                                                        Error during execution of the enabling command on the eUICC. In that
8.4      ISD-R             4.2   Execution error        case, the output data “euiccResponseData” contains the exact response
                                                        coming from the eUICC.

Table 162: Enable Profile Specific Status Codes

5.4.9 Profile Disabling

Function name: DisableProfile

Related Procedures: Profile Disabling via SM-DP

Function group: Platform Management

Function Provider: SM-SR

Description: This function allows the SM-DP authorised by the Operator to request a Profile Disabling to the SM-SR in charge of the management of the targeted eUICC, eUICC being identified by its EID.

The SM-DP SHALL indicate on behalf of which Operator it is requesting this operation.

The SM-SR receiving this request SHALL process it according to Profile Disabling procedure described in section 3.5 of this specification.

The SM-SR SHALL verify that the request is:

   Either sent on behalf of an Operator owning the targeted Profile

or

   Sent on behalf of an Operator that is not the owner of the targeted Profile, but the
    Operator owning the targeted Profile has granted a PLMA allowing the operation
    “DisableProfile” to the Operator requesting the operation.

The SM-SR MAY provide additional verifications.

This function may return:

   A ‘Function execution status’ with ‘Executed-Success’ indicating that the Profile has
    been disabled on the eUICC.
   A ‘Function execution status’ with ‘Executed-WithWarning’, with a status code as
    defined below, indicating that the Profile has been disabled on the eUICC, and
    deleted after application of a POL1 or POL2 rule.
   A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
    5.1.6.4
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
    section 5.1.6.4 or a specific status code as defined in the table here after

Additional input data:

Input data name                 Description                   Type    No. MOC
                  Identification of the targeted eUICC.
eid                                                           EID     1      M
                  See section 5.1.1.1 for type description.
                  Identification of the Profile to disable.
iccid                                                         ICCID   1      M
                  See section 5.1.1.1 for type description.

Table 163: Disable Profile Additional Input Data

Additional output data:

Output data name                               Description                                       Type      No. MOC
euiccResponseData Contains the detailed error returned by the eUICC in case of the           Hexadecimal   1    O
                  function execution failed at the eUICC.                                         String

Table 164: Disable Profile Additional Output Data

Specific status codes

Subj ect                   Reason
             Subj ect                  Reason                                           Description
 code                       code
                                                     Indicates that the target Profile can’t be disabled. (for example the Profile is the
8.1        eUICC           3.8      Refused
                                                     only Profile in the eUICC)
                                                     Indicates that the Profile change procedure couldn’t complete after enabling the
8.2        Profile         5.1       Inaccessible    Profile with the Fall-Back Attribute set, and the Profile change was rolled-back on
                                                     the eUICC,
8.1.1      EID             3.9      Unknown          Indicates that the eUICC, identified by this EID, is unknown to the SM-SR.
8.2.1      Profile ICCID   3.9      Unknown          Indicates that the Profile identified by this ICCID is unknown to SM -SR.
                                    Invalid          Indicates that the Profile identified by this ICCID is known to the SM -SR but
8.2.1      Profile ICCID   3.4      destination      installed on another eUICC than the one identified by the function caller.
                                    Invalid
8.2.1      Profile ICCID   3.5                       Indicates that the Profile was already Disabled
                                    Transition
                                    Not    Allowed Indicates that the function caller is not allowed to perform this function on the
8.2.1      Profile ICCID   1.2      (Authorisation) target Profile.
                                    Related Object The POL1 of the target Profile has triggered its deletion after disabling it
8.2.2      POL1            3.6      Exists         This status code SHALL only be sent along Status =”Executed -WithWarning”
8.2.2      POL1            3.8      Refused          The POL1 of the target Profile doesn’t allow this operation.
                                    Related Object The POL2 of the target Profile has triggered its deletion after disabling it
8.2.3      POL2            3.6
                                    Exists         This status code SHALL only be sent along Status =”Executed-WithWarning”
8.2.3      POL2            3.8      Refused          The POL2 of the target Profile doesn’t allow this operation.
                                                     No PLMA allows the SM-DP, or the Operator on behalf of which the SM -DP sent
8.2.7      PLMA            3.8      Refused          the request, to execute this operation.
                                                    Error during execution of the disabling command on the eUICC. In that case, the
8.4        ISD-R           4.2      Execution error output data “euiccResponseData contains the exact response coming from the
                                                    eUICC.

Table 165: Disable Profile Specific Status Codes

5.4.10 Delete an ISD-P

Function name: DeleteISDP

Related Procedures: Profile and ISD-P Deletion via SM-DP

Function group: Platform Management

Function Provider: SM-SR

Description: This function allows the SM-DP to request deletion of the target ISD-P with the Profile to the SM-SR in charge of the management of the targeted eUICC; eUICC being identified by its EID. The target Profile can only be a Profile that can be managed by the SM- DP authorised by the Operator.

The SM-DP SHALL indicate on behalf of which Operator it is requesting this operation.

On reception of the function request, the SM-SR SHALL perform the following minimum set of verifications:

   The SM-SR is responsible for the management of the targeted eUICC
   The ISD-P identified by its AID exists on the targeted eUICC
   The SM-DP is authorised to delete the target Profile by the Operator owning the
    target Profile.
   The POL2 of the target Profile allows the deletion
   The target Profile is not the Profile having the Fall-Back Attribute set

The SM-SR SHALL verify that the request is:

   Either sent on behalf of an Operator owning the targeted Profile
    or
   Sent on behalf of an Operator that is not the owner of the targeted Profile, b ut the
    Operator owning the targeted Profile has granted a PLMA allowing the operation
    “DeleteProfile” to the Operator requesting the operation.

The SM-SR MAY provide additional verifications.

In case one of these conditions is not satisfied, the SM-SR SHALL refuse the function request and return a ‘Function execution status’ indicating ‘Failed’ with the relevant status code (see table below).

The SM-SR receiving this request SHALL process it according to “Profile and ISD-P deletion via SM-DP” procedure described in section 3.7 of this specification.

In case the target Profile is “Enabled”, the SM-SR SHALL automatically disable it before executing the deletion. This function is described in section 4.1.1.3 of this specification.

This function may return:

   A ‘Function execution status’ with ‘Executed- Success’ indicating that the Profile has
    been deleted on the eUICC.
   A 'Function execution status' with 'Executed- WithWarning' indicating that the Profile
    has been deleted on the eUICC, with a status code as defined in section 5.1.6.4 or a
    specific status code as defined in the table below
   A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
    5.1.6.4
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
    section 5.1.6.4 or a specific status code as defined in the table below.
Additional input data:
                  Input data name                Description                Type   No. MOC
eid               Identification of the targeted eUICC.   EID    1   M

See section 5.1.1.1 for type description.

iccid             Identification of the Profile to delete.    ICCID   1   M

See section 5.1.1.1 for type description.

Table 166: Delete ISD-P Additional Input Data

Additional output data:

Output data name                                      Description                                   Type     No. MOC
                  Contains the detailed error returned by the eUICC in case the function execution
                  failed on eUICC. The response data is defined in ES8 depending of the requested
euiccResponseData function.                                                                          Byte[]   1   O

Table 167: Delete ISD-P Additional Output Data

Specific status codes
Subj ect              Reason
           Subj ect                 Reason                                          Description
 code                  code
                                                     Indicates that the eUICC, identified by this EID, is unknown to the
8.1.1      EID        3.9      Unknown
                                                     function provider.
           Profile                                   Indicates that the Profile identified by this ICCID is unknown to the
8.2.1                 3.9      Unknown
           ICCID                                     function provider.
                                                     Indicates that the Profile identified by this ICCID is known to the function
           Profile
8.2.1                 3.4      Invalid destination   provider but installed on another eUICC than the one identified by the
           ICCID
                                                     function caller.
           Profile             Not Allowed           Indicates that the function caller is not allowed to perform this function
8.2.1                 1.2
           ICCID               (Authorisation)       on the target Profile.
           Profile                                   Indicates that the Profile cannot be deleted because it is the last Profile
8.2.1                 3.8      Refused
           ICCID                                     of the eUICC or the Fall -Back Profile.
8.2.2      POL1       3.8      Refused               The POL1 of the Profile doesn’t allow this operation.
8.2.3      POL2       3.8      Refused               The POL2 of the Profile doesn’t allow this operation.
                                                     No PLMA allows the SM-DP, or the Operator on behalf of which the SM -
8.2.7      PLMA       3.8      Refused
                                                     DP sent the request, to execute this operation.
                               Not Present /         The target ISD-P was not found on this eUICC (in this case the Function
8.3        ISD-P      4.6
                               Missing               Execution Status SHALL be ‘Executed- WithWarning’
                                                     Error during execution of the deletion (or disabling) command on the
8.4        ISD-R      4.2      Execution error       eUICC. In that case, the output data “euiccResponseData contains the
                                                     exact response coming from the eUICC.

Table 168: Delete ISD-P Specific Status Codes

NOTE:in case Profile Disabling is performed automatically before deletion, this function MAY raises any status code coming from the execution of the Profile disabling function defined in section5.4.9.

5.4.11 Update Connectivity Parameters

Function name: UpdateConnectivityParameters

Related Procedures: -

Function group: Profile Management

Function Provider: SM-SR

Description: This function allows the Operator, or the SM-DP authorised by the Operator to update the Connectivity Parameters store in the ISD-P, identified by its ICCID, and installed on an eUICC identified by its EID.

The function can update a Profile in “Disabled” or “Enabled” state and SHALL return an error for any other Profile state.

The function updates the definition of existing Connectivity Parameters.

This function may return:

   A ‘Function execution status’ with ‘Executed- Success’ indicating that the update of
    the Connectivity Parameters function has been successfully executed by the SM-SR
    as requested by the function caller.
   A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
    5.1.6.4
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
    section 5.1.6.4 of a specific status code as defined in the table below.
Additional input data:
      Input data name                                     Description                                        Type        No. MOC
                          Identification of the targeted eUICC.
eid                                                                                                          EID            1       M
                          See section 5.1.1.1 for type description.
                          Identification of the Profile
iccid                                                                                                       ICCID           1       M
                          See section 5.1.1.1 for type description.
                          A command string secured with SCP03 as described in section 4.1.3.2,
                          and including ES8 command “Connectivity Parameters Update”                    Hexadecimal
connectivityParameters                                                                                                      1       M
                          specified in section 4.1.3.4, containing the connectivityParameters to           String
                          associate with the identified Profile.

Table 169: Update Connectivity Parameters Additional Input Data

Additional output data:

Output data name                                    Description                                         Type         No. MOC
                       Contains the detailed error returned by the eUICC in case of update of        Hexadecimal
euiccResponseData                                                                                                      1       O
                       the Connectivity Parameters in the ISD-P on the targeted eUICC.                  String

Table 170: Update Connectivity Parameters Additional Output Data

Specific status codes
 Subj ect               Reason
             Subj ect               Reason                                          Description
   code                  code
                                                  Indicates that the eUICC, identified by this EID, is unknown to the function
8.1.1       EID        3.9       Unknown
                                                  provider
            Profile                               Indicates that the Profile identified by this ICCID is unknown to the function
8.2.1                  3.9       Unknown
            ICCID                                 provider.
                                                 Indicates that the Profile identified by this ICCID is known to the function
           Profile               Invalid
8.2.1                   3.4                      provider but installed on another eUICC than the one identified by the
           ICCID                 destination
                                                 function caller.
                                                 Error during execution of Connectivity Parameters update. In that case, the
                                 Execution
8.3        ISD-P        4.2                      output data “euiccResponseData” contains the exact response coming from
                                 error
                                                 the eUICC.

Table 171: Update Connectivity Parameters Specific Status Codes

5.4.12 Notify a Profile is Disabled

Function name: HandleProfileDisabledNotification

Related Procedures: Profile Download and Installation, Profile Enabling, Profile Enabling via SM-DP, Fall-Back Activation Procedure, Profile Enabling via M2MSP

Function group: Platform Management

Notification handler/recipient: SM-DP

Description: This function SHALL be called to notify that the Profile identified by its ICCID has been disabled on the eUICC identified by its EID.

The SM-SR SHALL send this notification to all SM-DP servers that match one or the other of the following conditions:

   The SM-DP can relay the notification to the Operator that owns the Profile, and the
    Operator has not opted to not receive such notifications (see section 3.21).
   The SM-DP can relay the notification to another Operator, and the Operator owner of
    the Profile has granted the other Operator with a PLMA authorising this Operation
    “HandleProfileDisabledNotification”.

ICCID may be not enough to identify right address of recipient, SM-SR should map it internally to Operator notification endpoint.

This notification also conveys the date and time specifying when the operation has done.

In case multiple handlers are served, the SM-SR SHOULD ensure completionTimestamp to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
      Input data name                                   Description                                       Type       No. MOC
                         Identification of the targeted eUICC.
eid                                                                                                       EID        1     M
                         See section 5.1.1.1 for type description.
                      Identification of the Profile that has been disabled.
Iccid                                                                                                ICCID     1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Operator owner of the Profile that has been disabled.
mno-id                                                                                                OID      1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                 DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 172: Handle Profile Disabled Notification Additional Input Data

5.4.13 Notify a Profile Enabling

Function name: HandleProfileEnabledNotification

Related Procedures: Profile Disabling, Profile Disabling via SM-DP, Profile Enabling via M2M SP, Profile Disabling via M2M SP, Fall-Back Activation Procedure

Function group: Platform Management

Notification handler/recipient: SM-DP

Description: This function SHALL be called to notify that the Profile identified by its ICCID has been enabled on the eUICC identified by its EID.

The SM-SR SHALL send this notification to all SM-DP servers that match one or the other of the following conditions:

      The SM-DP can relay the notification to the Operator that owns the Profile, and the
       Operator has not opted to not receive such notifications (see section 3.21)
      The SM-DP can relay the notification to another Operator, and the Operator owner of
       the Profile has granted the other Operator with a PLMA authorising this Operation
       “HandleProfileEnabledNotification”.

ICCID may be not enough to identify right address of recipient, SM-SR should map it internally to Operator notification endpoint.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure completionTimestamp to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
   Input data name                                    Description                                      Type     No. MOC
eid                   Identification of the targeted eUICC.                                           EID      1   M

See section 5.1.1.1 for type description.

                       Identification of the Profile that has been disabled.
iccid                                                                                                ICCID     1       M
                       See section 5.1.1.1 for type description.
                       Identification of the Operator owner of the Profile that has been enabled.
mno-id                                                                                                OID      1       M
                       See section 5.1.1.1 for type description.
                       Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                 DATETIME   1       M
                       See section 5.1.1.1 for type description.

Table 173: Handle Profile Enabled Notification Additional Input Data

5.4.14 Notify an SM-SR Change

Function name: HandleSMSRChangeNotification

Related Procedures: SM-SR Change

Function group: eUICC Management

Function Provider: SM-DP

Description: This function SHALL be called for notifying each SM-DP authorised by the Operator owning a Profile hosted in the eUICC, identified by its EID, that the SM-SR has changed. The notification is sent by the new SM-SR to the SM-DP, which SHALL route this notification to the Operator.

This notification also conveys the date and time specifying when the operation has been done.

This notification is not related to a particular Profile. It is up to the notification recipient to perform any action related to each Profile that is deployed on this eUICC

Additional input data:
  Input data name                                       Description                                      Type    No. MOC
                        The relevant part of the eUICC Information Set linked with the Operator
                        owning the Profile hosted in the eUICC.
eis                                                                                                      EIS         1   M
                        See section 5.1.1.1 for type description.
                        The list of EIS data fields that SHALL be included is defined in Annex E.
                        Identification of the Operator concerned by the SM-SR change.
mno-id                                                                                                   OID         1   M
                        See 5.1.1.1 for type description.
                        Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                   DATETIME       1   M
                        See section 5.1.1.1 for type description.

Table 174: Handle SM -SR Change Notification Additional Input Data

Additional output data:

No output data is expected in response to this notification.

5.4.15 Notify a Profile Deletion

Function name: HandleProfileDeletedNotification

Related Procedures: Profile Enabling, Profile Enabling via SM-DP, Profile Enabling via M2M SP, Profile Disabling via M2M SP, profile and ISD-P Deletion via M2M SP

Function group: Platform Management

Notification handler/recipient: SM-DP

Description: This function SHALL be called to notify that the Profile identified by its ICCID has been deleted on the eUICC identified by its EID.

The SM-SR SHALL send this notification to all SM-DP servers that match one or the other of the following conditions:

     The SM-DP can relay the notification to the Operator that owns the Profile, and the
      Operator has not opted to not receive such notifications (see section 3.21)
     The SM-DP can relay the notification to another Operator, and the Operator owner of
      the Profile has granted the other Operator with a PLMA authorising this Operation
      “HandleProfileDeletedNotification”.

ICCID may be not enough to identify right address of recipient; SM-SR should map it internally to SM-DP notification endpoint.

This notification also conveys the date and time specifying when the operation has been done. In case of multiply handlers are served, SM-SR SHOULD ensure ‘completionTimestamp’ to be equal for every message.

Additional input data:

Input data name                                   Description                                      Type     No. MOC
                      Identification of the targeted eUICC.
eid                                                                                                  EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile that has been deleted.
iccid                                                                                               ICCID     1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Operator owner of the Profile that has been deleted.
mno-id                                                                                               OID      1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 175: Handle Profile Deleted Notification Additional Input Data

5.4.16 Setting Authorisations of M2M -SP to Access Profiles

Function name: SetPLMA

Related Procedures: Set Profile Lifecycle Management Authorisation via SM-DP

Function group: Profile Management

Function Provider: SM-SR

Description:

This function allows the Operator owning Profiles to grant a PLMA to an M2M SP to perform certain operations, or receive certain notifications, related to a set of Profiles, identified by a Profile Type.

The SM-SR receiving this request SHALL verify that the mno-id in the PLMA matches the mno-id of the Operator on behalf of which the SM-DP declares to send this request.

If the request is acceptable, the SM-SR SHALL record the PLMA. The new PLMA overwrites the previous PLMA that might have been granted with the same identifiers.

From this point on, any request from the M2M SP on a Profile matching these identifiers, or any notification to the M2M SP related to a Profile matching these identifiers, SHALL be allowed or not based on the new PLMA, as described in sections 5.7.1.1, 5.7.1.2, and 5.7.1.3.

This function may return:

      A ‘Function execution status’ with ‘Executed- Success’ indicating that the
       authorisations have been configured in the SM-SR.
      A ‘Function execution status’ with ‘Executed-WithWarning’ with a specific status code
       as defined in the table here after, indicating that the authorisations have been
       configured in the SM-SR but that some side-effects of this configuration may require
       the attention of the Operator.
      A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
       section 5.1.6.4 or a specific status code as defined in the table here after.

Additional input data:

Input data name                                  Description                                    Type   No.   MOC
plma              The specification of the PLMA, and the criteria on which this PLMA applies.   PLMA   1     M
                  See section 5.1.1.2.14 for type description.

Table 5416-A: SetPLMA Additional Input Data

Additional output data:

      None

Specific status codes

Subj ect               Reason
            Subj ect                 Reason                                      Description
 code                  code
                                                    Indicates that the Profile Type in the PLMA doesn’t match the Profile
                                                    Type of any Profile owned by the Operator identified by its mno -id.
           Profile
 8.2.5                  4.9     Unassigned          The SM-SR MAY support this Status Code. If it does support it, the SM-
           Type
                                                    SR SHALL record the PLMA anyway, and the Execution Status SHALL
                                                    be Executed-WithWarning
                                                  Indicates that the new PLMA has overwritten a former PLMA on the
                               Related    Objects same identifiers. In this case the Execution Status SHALL be Executed-
8.2.7     PLMA         3.6     Exists
                                                  WithWarning
                              Not        Allowed Indicates that the requesting SM -DP is not allowed to configure PLMAs
8.2      Profile      1.2     (Authorisation)    for the specified Operator
                                                  Indicates that the M2M SP to grant authorisations to is unknown to or not
8.9      M2M SP       1.1     Unknown
                                                  connected to this SM-SR
                                                  Indicates that the Operator, addressed by the mno -id in the PLMA is
8.10     Operator     1.1     Unknown             unknown.

Table 5416-B: SetPLMA Specific Status Codes

5.4.17 Retrieving Authorisations of M2M SP to Access Profiles

Function name: GetPLMA

Related Procedures: Retrieve Profile Lifecycle Management Authorisation by Operator

Function group: Profile Management

Function Provider: SM-SR

Description:

This function allows the SM-DP to retrieve, on behalf of an Operator owning Profiles, a list of PLMAs applicable to a certain Profile, or a certain Profile Type, or for a certain M2M SP.

The same function can also be used on behalf of an Operator playing the role of an M2M SP, to retrieve the list of PLMAs granted to this Operator, and applicable to a certain Profile, or a certain Profile Type, owned by another Operator.

The SM-SR SHALL verify that the request is

      Either sent on behalf of an Operator owning the targeted Profile
       or
      Sent on behalf of an Operator that is not the owner of the targeted Profile, but the
       Operator owning the targeted Profile has granted a PLMA allowing at least one
       operation for the target Profile or Profile Type to the Operator requesting the
       operation.

If this verification fails, the SM-SR SHALL terminate the request and return a response with the ‘Function execution status’ indicating ‘Failed’, and no PLMA.

Otherwise, the SM-SR SHALL return the complete list of all PLMAs applicable to the specified search criterion; if the search criterion is on a specific Profile or Profile Type, this includes even PLMAs that are granted to an M2M SP that is not the Operator on behalf of which the SM-DP sent this request.

In case the list of PLMAs is very long, the SM-SR MAY truncate the result. The caller can then issue another call to getPLMA with more restrictive criteria.

NOTE The order of the PLMAs returned in the truncated list is implementation-dependent.

This function may return:

     A ‘Function execution status’ with ‘Executed- Success’, and additional output data
      providing the PLMAs.
     A ‘Function execution status’ with ‘Executed-WIthWarning’, to indicate that the result
      was truncated, plus additional output data providing part of the list of applicable
      PLMAs.
     A ‘Function execution status’ indicating ‘Failed’ if the requester was not allowed to
      request this information.

Additional input data:

Input data name                                      Description                                 Type     No.   MOC
                   Identification of the Profile type for which PLMAs are searched
profileType                                                                                       String   1     C
m2m-sp-id          Identification of the M2M SP for which PLMAs are searched
                                                                                                   OID     1     C
                   Identification of one specific Profile
iccid                                                                                             ICCID    1     C
mno-id             Identification of the Operator owning the Profiles to be matched (this input
                                                                                                   OID     1     C
                   datum SHALL be present only in case the search criterion is a Profile Type).
                   See section 5.1.1.1 for type description.

Table 5417-A: GetPLMA Additional Input Data

One and only one of the input data profileType, m2m-sp-id and iccid SHALL be present.

Additional output data:

Output data name                        Description                    Type   No. MOC
                    The list of PLMAs that match the search criteria
plma                                                                   PLMA   N    M
                    See section 5.1.1.2.14 for type description.

Table 5417-B: GetPLMA Additional Output Data

Specific status codes

Subj ect               Reason
            Subj ect                 Reason                                         Description
 code                  code
                                                    Indicates that the Operator on behalf of which the SM -DP called the
           Function             Not Allowed         function is not the owner of the specified Profile, or doesn’t have a PLMA
  1.1                   1.2
           requester            (Authorisation)     granted that applies to the targeted Profile or Profile type (including, if the
                                                    targeted Profile or Profile type is unknown to this SM -SR)
                              Not Allowed         Indicates that the requesting SM -DP is not allowed to configure PLMAs
8.2      Profile      1.2     (Authorisation)     for the specified Operator
                                                  Indicates that the M2M SP is unknown to or not connected to this SM-
8.9      M2M SP       1.1     Unknown
                                                  SR
                                                  Indicates that the Operator, addressed by the mno -id in the PLMA is
8.10     Operator     1.1     Unknown             unknown.

Table 5417-C: GetPLMA Specific Status Codes

5.4.18 Notify a Profile Download

Function name: HandleProfileDownloadNotification

Related Procedures: Profile Download

Function group: Profile Management

Notification handler/recipient: SM-DP (when the corresponding Operator is in the role of an M2M SP)

Description: This function SHALL be called to notify an Operator (acting as an M2M SP from the point of view of another Operator) that the Profile identified by its ICCID has been downloaded on the eUICC identified by its EID.

The SM-SR SHALL inspect the PLMAs that apply to this Profile, and only send this notification to an SM-DP known to be serving an Operator that has been granted a PLMA by the Operator owner of the Profile for the authorised operation “HandleProfileDownloadedNotification”.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure ‘completionTimestamp’ to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:

Input data name                                     Description                                          Type       No. MOC
                        Identification of the targeted eUICC.
Eid                                                                                                         EID         1      M
                        See section 5.1.1.1 for type description.
                        Identification of the Profile that has been downloaded.
iccid                                                                                                      ICCID        1      M
                        See section 5.1.1.1 for type description.
                      Identification of the Operator owner of the Profile that has been
                      downloaded.
mno-id                                                                                             OID      1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                              DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 5418: Handle Profile Downloaded Notification Additional Input Data

5.4.19 Notify the Change of Policy Rules of a Profile

Function name: HandlePolicyRulesUpdatedNotification

Related Procedures: POL2 Update Via SM-DP

Function group: Platform Management

Notification handler/recipient: SM-DP DP (when the corresponding Operator is in the role of an M2M SP)

Description: This function SHALL be called to notify an Operator (acting as an M2M SP from the point of view of another Operator) that the Policy Rules have been updated on the Profile identified by its ICCID on the eUICC identified by its EID.

The SM-SR SHALL inspect the PLMAs that apply to this Profile, and only send this notification to an SM-DP known to be serving an Operator that has been granted a PLMA by the Operator owner of the Profile for the authorised operation “HandlePolicyRuleUpdatedNotification”.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure ‘completionTimestamp’ to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:

Input data name                                   Description                                   Type     No. MOC
                      Identification of the targeted eUICC.
Eid                                                                                                EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile whose POL2 has been updated.
iccid                                                                                             ICCID     1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Operator owner of the Profile whose POL2 has been
                      updated.
mno-id                                                                                             OID      1   M
                      See section 5.1.1.1 for type description.
                      Value of the POL2 after being updated by the Operator owning the Profile
Pol2                                                                                              POL2      1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                              DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 5419: Handle Policy Rules Updated Notification Additional Input Data

5.4.20 Notify a PLMA Setting

Function name: HandleSetPLMANotification

Related Procedures: Set Profile Lifecycle Management Authorisations, Set Profile Lifecycle Management Authorisation via SM-DP

Function group: Platform Management

Notification handler/recipient: SM-DP DP (when the corresponding Operator is in the role of an M2M SP)

Description: This function SHALL be called to notify an Operator (acting as an M2M SP) that a PLMA, granted by another Operator to it, has been set or updated.

This notification also conveys the date and time specifying when the operation has been done. In case of multiply handlers are served the SM-SR SHOULD ensure ‘completionTimestamp’ to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
  Input data name                                    Description                                   Type     No. MOC
plma                  The specification of the PLMA that now applies on a subset of Profiles.     PLMA      1   M
                      Information about the subset are contained in the PLMA structure.
                      See section 5.1.1.2.14 for type description.
                      Identification of the Operator owner of the Profile Type related to PLMA
mno-id                                                                                             OID      1   M
                      See section 5.1.1.1 for type description.
completionTimestamp Indication of the date/time when the operation has been performed.           DATETIME   1   M

See section 5.1.1.1 for type description.

Table 5420: Handle PLMA Setting Notification Additional Input Data

5.4.21 Setting Operator Configuration to Receive Notifications

Function name: SetONC

Related Procedures: Set Operator Notifications Configuration via SM-DP

Function group: Profile Management

Function Provider: SM-SR

Description:

This function allows the Operator to configure for which of its own Profiles, associated with a Profile Type, it wants to receive which kind of status change notifications; whatever the origin of the status change is.

The SM-SR receiving this request SHALL verify that the mno-id in the ONC matches the mno-id of the Operator on behalf of which the SM-DP declares to send this request.

If the request is acceptable, the SM-SR SHALL record the ONC. The new ONC overwrites the previous ONC that might have been granted with the same identifiers.

From this point on, any status change notification, irrespective of the cause and related to a Profile matching these identifiers, SHALL be sent or not based on the new ONC.

This function may return:

       A ‘Function execution status’ with ‘Executed-Success’ indicating that the notifications
        have been configured in the SM-SR.
       A ‘Function execution status’ with ‘Executed-WithWarning’ with a specific status code
        as defined in the table here after, indicating that the notifications have been
        configured in the SM-SR but that some side-effects of this configuration may require
        the attention of the Operator.
       A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
        section 5.1.6.4 or a specific status code as defined in the table here after.

NOTE:If no Operator Notification Configuration has yet been set in the SM-SR for a given Profile Type, then the Operator will receive all notifications for status changes for its own Profiles, associated with this Profile Type, see also section 3.21 for details.

Additional input data:

  Input data
                                               Description                                 Type   No.    MOC
    name
onc                   The specification of the ONC, and the criteri on on which this
                                                                                           ONC     1       M
                      ONC applies.

See section 5.1.1.2.15 for type description.

Table 5421-A: SetONC Additional Input Data

Additional output data:

       None

Specific status codes

Subj ect                Reason
            Subj ect                     Reason                                         Description
 code                     code
                                                          Indicates that the Profile Type in the ONC doesn’t match the Profile Type
                                                          of any Profile owned by the Operator identified by its mno -id.
            Profile
 8.2.5                    4.9       Unassigned            The SM-SR MAY support this Status Code. If it does support it, the SM-
            Type
                                                          SR SHALL record the ONC anyway, and the Execution Status SHALL
                                                          be Executed-WithWarning
                                                   Indicates that the new ONC has overwritten a former ONC on the same
                               Related     Objects identifiers. In this case the Execution Status SHALL be Executed-
8.2.8     ONC          3.6     Exists
                                                   WithWarning
                                                    Indicates that the Operator, addressed by the mno -id in the ONC, is
8.10     Operator     1.1     Unknown               unknown.
                              Not        Allowed Indicates that the requesting SM-DP is not allowed to configure ONCs
8.10     Operator     1.2
                              (Authorisation)    for the Operator, addressed by the mno-id in the ONC.

Table 5421-B: SetONC Specific Status Codes

5.4.22 Retrieving Operator Notification Configuration

Function name: GetONC

Related Procedures: Retrieve Operator Notifications Configuration via SM-DP

Function group: Profile Management

Function Provider: SM-SR

Description:

This function allows the Operator to retrieve a list of status change notifications it wants not to receive for its own Profiles, associated with a Profile Type.

The SM-SR receiving this request SHALL verify that the mno-id in the ONC matches the mno-id of the Operator on behalf of which the SM-DP declares to send this request.

If the request is acceptable, the SM-SR SHALL return the ONC including the list of notifications the Operator does not want to receive, applicable to the specified search criterion.

This function may return:

      A ‘Function execution status’ with ‘Executed-Success’, and additional output data
       providing the configured ONC.
      A ‘Function execution status’ with ‘Executed-WithWarning’ with a specific status code
       as defined in the table below, indicating that the notifications have been configured in
       the SM-SR but that some side-effects of this configuration may require the attention
       of the Operator, and additional output data providing the configured ONC.
      A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
       section 5.1.6.4 or a specific status code as defined in the table here after.

Additional input data:

Input data name                                      Description                                   Type     No.   MOC
profileType         Identification of the Profile Type for which the ONC applies is searched
                                                                                                   String   1     C
                    Identification of one specific Profile for which the ONC applies is searched
iccid                                                                                              ICCID    1     C

Table 5422-A: GetONC Additional Input Data

One and only one of the input data profileType and iccid SHALL be present.

Additional output data:

 Output
  data                                                Description                                                 Type   No. MOC
 name
            The ONC including the list of unwanted notifications that match the search criterion
            See section 5.1.1.2.15 for type description.
            NOTE:
onc         If no Operator Notification Configuration has yet been set in the SM -SR for a given Profile          ONC    N   M
            Type, then the output data of this function will list no notification names, as all notifications
            will be sent for Profiles assigned with this Profile Type. See also section 3.21.4 and table
            511215-A for details.

Table 5422-B: GetONC Additional Output Data

5.4.23 Setting the Emergency Profile Attribute

Function name: SetEmergencyProfileAttribute

Related Procedures: Emergency Profile Attribute Management, Emergency Profile Attribute Management via the M2M SP

Function group: Platform Management

Function Provider: SM-SR

Description:

This function allows the SM-DP authorised by the Operator to request the setting of the Emergency Profile Attribute on the targeted Profile to the SM-SR in charge of the management of the targeted eUICC; eUICC being identified by its EID.

The SM-DP SHALL indicate on behalf of which Operator it is requesting this operation.

The SM-SR SHALL verify that the request is

   Either sent on behalf of an Operator owning the targeted Profile
    or
   Sent on behalf of an Operator that is not the owner of the targeted Profile, but the
    Operator owning the targeted Profile has granted a PLMA allowing the operation
    “SetEmergencyProfileAttribute” to the Operator requesting the operation.

If one Profile currently has the Emergency Profile Attribute set, the SM-SR SHALL verify that the Operator owning the Profile with the Emergency Profile Attribute set has granted a PLMA authorising the operation “UnsetEmergencyProfileAttribute” to the Operator requesting the operation.

The SM-SR MAY provide additional verifications.

The SM-SR receiving this request SHALL process it according to “Emergency Profile Attribute Management” procedure described in the section 3.25 of this specification.

After setting the Emergency Profile Attribute, the SM-SR SHALL add or update the AdditionalProperty ‘gsma.ESIM.EmergencyProfile.AID’ of the EIS. This function may return:

      A ‘Function execution status’ with ‘Executed- Success’ indicating that the Emergency
       Profile Attribute has been set on the targeted Profile.
      A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
       5.1.6.4
      A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
       section 5.1.6.4 of a specific status code as defined in the table here after.

Additional input data:

Input data name                                   Description                                    Type     No.   MOC
eid                  Identification of the targeted eUICC.                                       EID       1    M
                     See section 5.1.1.1 for type description.
                     Identification of the Profile to get the Emergency Profile Attribute set.
iccid                                                                                            ICCID     1    M
                     See section 5.1.1.1 for type description.

Table 5423-A: Set Emergency Profile Attribute Additional Input Data

Additional output data:

Output data name                                        Description                                         Type        No. MOC
                  Contains the detailed error returned by the eUICC in case the function
                                                                                         Hexadecimal
euiccResponseData execution failed on eUICC. The response data is defined in String                                      1    O
                  ES5.SetEmergencyProfileAttribute.

Table 5423-B: Set Emergency Profile Attribute Additional Output Data

Specific status codes

Subj ect                    Reason
                 Subj ect               Reason                                           Description
 code                       code
                                                      Indicates that the eUICC, identified by this EID, is unknown to the function
 8.1.1           EID         3.9     Unknown          provider.
                Profile                              Indicates that the Profile identified by this ICCID is unknown to the function
8.2.1                       3.9     Unknown
                ICCID                                provider.
                                                     Indicates that the Profile identified by this ICCID is known to the function
                Profile             Invalid
8.2.1                       3.4                      provider but installed on another eUICC than the one identified by the function
                ICCID               destination
                                                     caller.
                                                     No PLMA allows the SM-DP, or the Operator on behalf of which the SM-DP
8.2.7           PLMA        3.8     Refused
                                                     sent the request, to execute this operation.
                                                    Error during execution of the command on the eUICC. In that case, the output
                                   Execution
8.4            ISD-R       4.2                      data “euiccResponseData” contains the exact response coming from the
                                   error
                                                    eUICC.

Table 5423-C: Set Emergency Profile Attribute Specific Status Codes

5.4.24 Notifying the Emergency Profile Attribute Setting

Function name: HandleEmergencyProfileAttributeSetNotification

Related Procedures: Emergency Profile Attribute Management, Emergency Profile Attribute Management via M2M SP

Function group: Profile Management

Notification handler/recipient: SM-DP

Description: This function SHALL be called to notify that the Emergency Profile Attribute has been set on the Profile identified by its ICCID on the eUICC identified by its EID.

The SM-SR SHALL send this notification to all SM-DP servers that match one or the other of the following conditions:

   The SM-DP can relay the notification to the Operator that owns the Profile, and the
    Operator has opted to receive such notifications (see section 3.21)
   The SM-DP can relay the notification to another Operator, and the Operator owner of
    the Profile has granted the other Operator with a PLMA authorising this Operation
    “HandleEmergencyProfileAttributeSetNotification”.
   The SM-DP can relay the notification to any Operator having a Profile on this eUICC.
    In this case Identification of the Profile that has the Emergency Profile Attribute set
    and Identification of the Operator owner of the Profile that has the Emergency Profile
    Attribute set are optional.

ICCID may be not enough to identify right address of recipient, SM-SR should map it internally to Operator notification endpoint.

This notification also conveys the date and time specifying when th e operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure completionTimestamp to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
  Input data name                                     Description                                     Type     No. MOC
                      Identification of the targeted eUICC.
eid                                                                                                   EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile that has the Emergency Profile Attribute set.
iccid                                                                                                ICCID     1   C
                      See section 5.1.1.1 for type description.
                      Identification of the Operator owner of the Profile that has the Emergency
                      Profile Attribute set.
mno-id                                                                                                OID      1   C

See section 5.1.1.1 for type description.

                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                 DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 5424: Handle Emergency Profile Attribute Set Notification Additional Input Data

5.4.25 Notifying the Emergency Profile Attribute Unsetting

Function name: HandleEmergencyProfileAttributeUnsetNotification

Related Procedures: Emergency Profile Attribute Management, Emergency Profile Attribute Management via M2M SP

Function group: Profile Management

Notification handler/recipient: SM-DP

Description: This function SHALL be called to notify that the Emergency Profile Attribute has been unset on the Profile identified by its ICCID on the eUICC identified by its EID.

The SM-SR SHALL send this notification to all SM-DP servers that match one or the other of the following conditions:

   The SM-DP can relay the notification to the Operator that owns the Profile, and the
    Operator has opted to receive such notifications (see section 3.21)
   The SM-DP can relay the notification to another Operator, and the Operator owner of
    the Profile has granted the other Operator with a PLMA authorising this Operation
    “HandleEmergencyProfileAttributeUnsetNotification”.

ICCID may be not enough to identify right address of recipient, SM-SR should map it internally to Operator notification endpoint.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure completionTimestamp to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
  Input data name                                     Description                                       Type     No. MOC
                      Identification of the targeted eUICC.
eid                                                                                                     EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile that has the Emergency Profile Attribute unset.
iccid                                                                                                  ICCID     1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Operator owner of the Profile that has the Emergency
                      Profile Attribute unset.
mno-id                                                                                                  OID      1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                   DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 5425: Handle Emergency Profile Attribute Unset Notification Additional Input

Data

5.4.26 Setting the Fall-Back Attribute

Function name: SetFallBackAttribute

Related Procedures: Fall-Back Attribute Management

Function group: Platform Management

Function Provider: SM-SR

Description:

This function allows the SM-DP authorised by the Operator to request the setting of the Fall- Back Attribute on the targeted Profile to the SM-SR in charge of the management of the targeted eUICC; eUICC being identified by its EID.

The SM-DP SHALL indicate on behalf of which Operator it is requesting this operation.

The SM-SR SHALL verify that the request is

     Either sent on behalf of an Operator owning the targeted Profile
      or
     Sent on behalf of an Operator that is not the owner of the targeted Profile, but the
      Operator owning the targeted Profile has granted a PLMA allowing the operation
      “SetFallBackAttribute” to the Operator requesting the operation.

In both cases, the SM-SR SHALL verify that the Operator owning the Profile which currently has the Fall-Back Attribute set has granted, to the Operator requesting the operation, a PLMA authorising the operation “UnsetFallBackAttribute”, applicable for the Profile that currently has the Fall-Back Attribute set.

The SM-SR MAY provide additional verifications.

The SM-SR receiving this request SHALL process it according to “Fall-Back Attribute Management via SM-DP” procedure described in the section 3.28 of this specification.

This function may return:

     A ‘Function execution status’ with ‘Executed- Success’ indicating that the Fall-Back
      Attribute has been set on the targeted Profile.
     A ‘Function execution status’ with ‘Expired’ with a status code as defined in sec tion
      5.1.6.4
     A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
      section 5.1.6.4 of a specific status code as defined in the table here after.

Additional input data:

Input data name                             Description          Type   No.   MOC
eid               Identification of the targeted eUICC.           EID    1    M
                  See section 5.1.1.1 for type description.
                   Identification of the Profile on which to set the Fall -Back Attribute.
iccid                                                                                        ICCID   1     M
                   See section 5.1.1.1 for type description.

Table 5426-A: Set Fall-Back Attribute Additional Input Data

Additional output data:

Output data name                                      Description                                          Type       No. MOC
                  Contains the detailed error returned by the eUICC in case the function
euiccResponseData execution failed on eUICC. The response data is defined in Hexadecimal                                 1   O
                                                                                         String
                  ES5.SetFallBackAttribute.

Table 5426-B: Set Fall-Back Attribute Additional Output Data

Specific status codes

Subj ect                   Reason
               Subj ect                Reason                                           Description
 code                       code
                                                     Indicates that the eUICC, identified by this EID, is unknown to the function
 8.1.1        EID           3.9     Unknown
                                                     provider.
             Profile                                Indicates that the Profile identified by this ICCID is unknown to the function
8.2.1                      3.9     Unknown
             ICCID                                  provider.
                                                    Indicates that the Profile identified by this ICCID is known to the function
             Profile               Invalid
8.2.1                      3.4                      provider but installed on another eUICC than the one identified by the function
             ICCID                 destination
                                                    caller.
8.2.2        POL1          3.8     Refused          The POL1 of a Profile on the targeted eUICC doesn’t allow this operation.
                                                    No PLMA allows the SM-DP, or the Operator on behalf of which the SM-DP
8.2.7        PLMA          3.8     Refused
                                                    sent the request, to execute this operation.
                                                   Error during execution of the command on the eUICC. In that case, the output
                                  Execution
8.4         ISD-R         4.2                      data “euiccResponseData” contains the exact response coming from the
                                  error
                                                   eUICC.

Table 5426-C: Set Fall-Back Attribute Specific Status Codes

NOTE:A POL1 may interfere with the Set Fall-Back Attribute operation in very specific circumstances described in section 4.1.1.7.

5.4.27 Notifying the Fall-Back Attribute is Set

Function name: HandleProfileFallBackAttributeSetNotification

Related Procedures: Fall-Back Attribute Management, Fall-Back Attribute Management via SM-DP, Fall-Back Attribute Management via M2M SP

Function group: Profile Management

Notification handler/recipient: SM-DP

Description:

This function SHALL be called to notify that the Fall-Back Attribute has been set on the Profile identified by its ICCID on the eUICC identified by its EID.

The SM-SR SHALL send this notification to all SM-DP servers that match one or the other of the following conditions:

   The SM-DP can relay the notification to the Operator that owns the Profile, and the
    Operator has opted to receive such notifications (see section 3.21)
   The SM-DP can relay the notification to another Operator, and the Operator owner of
    the Profile has granted the other Operator with a PLMA authorising this Operation
    “HandleProfileFallBackAttributeSetNotification”.

ICCID may be not enough to identify right address of recipient, SM-SR should map it internally to Operator notification endpoint.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure completionTimestamp to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:

Input data name                                     Description                                         Type     No. MOC
                      Identification of the targeted eUICC.
eid                                                                                                       EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile on which the Fall-Back Attribute has been set.
iccid                                                                                                    ICCID     1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Operator owner of the Profile that has had its Fall -Back
                      Attribute set.
mno-id                                                                                                    OID      1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                     DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 5427: Handle Profile Fall-Back Attribute Set Notification Additional Input Data

5.4.28 Notifying the Fall-Back Attribute is Unset

Function name: HandleProfileFallBackAttributeUnsetNotification

Related Procedures: Fall-Back Attribute Management, Fall-Back Attribute Management via SM-DP, Fall-Back Attribute Management via M2M SP

Function group: Profile Management

Notification handler/recipient: SM-DP

Description: This function SHALL be called to notify that the Fall-Back Attribute has been unset on the Profile identified by its ICCID on the eUICC identified by its EID.

The SM-SR SHALL send this notification to all SM-DP servers that match one or the other of the following conditions:

   The SM-DP can relay the notification to the Operator that owns the Profile, and the
    Operator has opted to receive such notifications (see section 3.21)
   The SM-DP can relay the notification to another Operator, and the Operator owner of
    the Profile has granted the other Operator with a PLMA authorising this Operation
    “HandleProfileFallBackAttributeUnsetNotification”.

ICCID may be not enough to identify right address of recipient, SM-SR should map it internally to Operator notification endpoint.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure completionTimestamp to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:

Input data name                                     Description                                    Type     No. MOC
                      Identification of the targeted eUICC.
eid                                                                                                  EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile on which the Fall-Back Attribute has been
                      unset.
iccid                                                                                               ICCID     1   M

See section 5.1.1.1 for type description.

                      Identification of the Operator owner of the Profile on which the Fall-Back
                      Attribute has been unset.
mno-id                                                                                               OID      1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 5427: Handle Profile Fall-Back Attribute Unset Notification Additional Input Data

5.5 ES4 (Operator - SM-SR, and M2M SP – SM-SR) Interface Description

NOTE:The execution of several ES4 functions by the SM-SR is conditioned by the verification that the Operator or M2M SP requesting to perform an operation on a Profile, or the Operator or M2M SP to be notified, is authorised for this operation or notification by the owner of the Profile. The specification of this verification by the SM-SR is described in sections 5.7.1.2 and 5.7.1.3.

5.5.1 Getting eUICC Information

Function name: GetEIS

Related Procedures: Profile Download and Installation

Function group: Profile Management

Function Provider: SM-SR

Description: This function allows the Operator or the M2M SP to retrieve the eUICC Information Set (EIS) of a particular eUICC from the SM-SR information database based on the EID. The retrieved EIS contains only the data that is applicable for that particular Operator. The Operator utilises the retrieved EIS, for instance, to verify the eligibility of the eUICC (for example type, certificate and memory).

This function may return:

     A ‘Function execution status’ with ‘Executed- Success’ indicating that the download
      function has been successfully executed on the SM-SR as requested by the function
      caller.
     A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
      section 5.1.6.4 of a specific status code as defined in the table below.

Additional input data:

Input data name                  Description                   Type No. MOC
                   Identification of the targeted eUICC.
eid                                                            EID    1     M
                   See section 5.1.1.1 for type description.

Table 176: Get EIS Additional Input Data

The SM-SR SHALL filter the list of Profiles returned in the EIS, considering the authorisation granted by the Profile owners; for each Profile, this includes:

     If the function caller is the owner of the Profile, the SM-SR SHALL include this Profile
      in the returned EIS.
     If the function caller is not the owner of the targeted Profile, the SM-SR SHALL
      include the Profile in the returned EIS only if the Operator owning the Profile has
      granted a PLMA allowing the operation “GetEIS” to the function caller.

Additional output data:

Output data name                                 Description                                   Type No. MOC
                   The relevant eUICC Information Set of the eUICC
eis                                                                                            EIS   1   C
                   See         section       5.1.1.1       for       type       description.
                   The list of EIS data fields that SHALL be included is defined in Annex E.

Table 177: Get EIS Additional Output Data

Specific status codes
Subject             Reason
          Subject                    Reason                                         Description
 code                code
8.1.1    EID        1.1     Unknown                    Indicates that the EID, is unknown to the function provider
                           Not               Allowed Function requester is not allowed to manage this EIS, identified by
8.6     EIS        1.2
                           (Authorisation)           this EID.

Table 178: Get EIS Specific Status Code

5.5.2 Updating the Policy Rules of a Profile

Function name: UpdatePolicyRules

Related Procedures: -

Function group: Profile Management

Function Provider: SM-SR

Description: This function allows the Operator to update POL2 of a Profile, identified by its ICCID, and installed on an eUICC identified by its EID.

The general description of this function is detailed in section 5.4.6 of this specification.

5.5.3 Updating eUICC Information

Function name: UpdateSubscriptionAddress

Related Procedures: Profile Enabling

Function group: Profile Management

Function Provider: SM-SR

Description: This function enables the caller to update the Subscription Address for a Profile in the eUICC Information Set (EIS) of a particular eUICC identified by the EID and ICCID. The function replaces the content of the Subscription Address. For consistency within the system, it is the responsibility of the caller to ensure that all data is provided.

On reception of the function request, the SM-SR SHALL perform the following minimum set of verifications:

      The SM-SR is responsible for the management of the targeted eUICC.
      The Profile identified by its ICCID is loaded on the targeted eUICC.
      The target Profile is owned by the requesting Operator, or an Operator that had
       granted a PLMA that authorises the requesting M2M SP to perform the operation
       “UpdateSubscriptionAddress” on a Profile that matches the criteria of the PLMA (see
       section 5.7.1.1 for the detail of the matching of the criteria)
This function may return:
      A ‘Function execution status’ with ‘Executed- Success’ indicating that the
       UpdateSubscriptionAddress function has been successfully executed by the SM-SR
       as requested by the function caller.
A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
section 5.1.6.4 of a specific status code as defined in the table below.
Additional input data:
                 Input data name                        Description                           Type            No. MOC
                               Identification of the targeted eUICC.
eid                                                                                 EID             1     M
                               See section 5.1.1.1 for type description.
                               Identification of the target Profile.
iccid                                                                              ICCID            1     M
                               See section 5.1.1.1 for type description.
newSubscriptionAddress The new Subscription Address                        Subscription Address     1     M

Table 179: Update Subscription Address Additional Input Data

Additional output data:

This function has no additional output data.

Specific status codes

Subj ect                        Reason
                 Subj ect                               Reason                                      Description
  code                               code
                                                                            Indicates that the EIS identified by this EID, is unknown to
8.1.1      EID                 1.1              Unknown
                                                                            the function provider
                                                                            Indicates that the Profile identified by the ICCID, is unknown
8.2.1      ICCID               1.1              Unknown
                                                                            to the function provider
           Subscription                         Not Allowed                 Function caller is not allowed to manage the Subscription
8.2.6                          1.2
           Address                              (Authorisation)             Address.

Table 180: Update Subscription Address Status Codes

5.5.4 Auditing eUICC Information

Function name: AuditEIS

Related Procedures: Profile Download and Installation

Function group: Profile Management

Function provider: SM-SR

Description: This function allows the Operator to retrieve the up to date EIS information. The SM-SR SHALL use the relevant functions of the ES5 interface to retrieve the information from the eUICC. The SM-SR SHALL update its EIS database upon the basis of this information.

If the function caller provides a list of ICCID of Profiles to audit, the SM-SR SHALL verify for each Profile that the function caller

   is either the owner of the targeted Profile
    or
   is authorised by the Operator owning the targeted Profile(s)

to perform the operation “AuditEIS” on a Profile that matches the criteria of the PLMA (see section 5.7.1.1 for the detail of the matching of the criteria).

This SHALL also be applied if the list of ICCIDs identifies

   Profiles that are owned by this Operator
    and / or
   Profiles that are owned by other Operators.

The SM-SR MAY provide additional verifications.

This function may return:

    A ‘Function execution status’ with ‘Executed- Success’ indicating that the function has
     been successfully executed on the SM-SR as requested by the function caller.
    A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
     5.1.6.4
    A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
     section 5.1.6.4 of a specific status code as defined in the table below.

Additional input data:

Input data name                      Description                       Type   No.   MOC
                  Identification of the targeted eUICC.to be audited
eid                                                                    EID    1     M
                  See section 5.1.1.1 for type description.
iccid-list        List of “iccid” identifying Profiles to be audited   ICCID 1..N   C

Table 181: AuditEIS Additional Input Data

If no list of ICCIDs is provided, it is implied that all authorised Profiles in the EIS are requested.

The SM-SR SHALL filter the list of Profiles returned in the EIS, considering the authorisation granted by the Profile owners; for each Profile, this includes:

    If the function caller is the owner of the Profile, the SM-SR SHALL include this Profile
     in the returned EIS.
    If the function caller is not the owner of the targeted Profile, the SM-SR SHALL
     include the Profile in the returned EIS only if the Operator owning the Profile has
     granted a PLMA allowing the operation “AuditEIS” to the function caller.

Additional output data:

Output
 data                                                 Description                                                Type   No. MOC
name
             For the relevant eUICC Information Set see section 5.1.1.1 for type description. The list of
             EIS data fields that SHALL be included is defined in Annex E.Only data for the requested
Eis          Profiles is returned within EIS. The Profiles that do not belong to the requestor are not included   EIS    1      C
             in the response. This access control function is realised within the SM -SR, there is no need to
             limit the data on the eUICC side.

Table 182: AuditEIS Additional Output Data

Specific status codes

Subj ect                  Reason
            Subj ect                         Reason                                          Description
 code                       code
                                       Delivered With No The function execution request has been delivered to the remote entity
  1.6       Function         5.4       Response          but no response is received.
                                                             Indicates that the eUICC, identified by this EID, is unknown to the function
8.1.1      EID              3.9       Unknown                provider
                                     Not         Allowed One or more Profiles identified by ICCIDs in the list do not belong to
8.2       Profile          1.2       (Authorisation)     function requester
                                                             Indicates that the Profile identified by one of the ICCIDs in the list is
           Profile
8.2.1                       3.4       Invalid destination    known to the function provider but installed on another eUICC than the
           ICCID
                                                             one identified by the function caller.
8.2.7      PLMA             3.8       Refused                No PLMA allows the M2M SP to execute this operation.
                                     Not         Allowed Function requester is not allowed to manage this EIS, identified by this
8.6       EIS              1.2
                                     (Authorisation)     EID.

Table 183: AuditEIS Additional Specific Status Codes

5.5.5 Profile Enabling

Function name: EnableProfile

Related Procedures: Profile Enabling

Function group: Platform Management

Function Provider: SM-SR

Description: This function allows the Operator to request a Profile Enabling to the SM-SR in charge of the management of the targeted eUICC; eUICC being identified by its EID.

On reception of the function request, the SM-SR SHALL perform the following minimum set of verifications:

   The SM-SR is responsible for the management of the targeted eUICC.
   The Profile identified by its ICCID is loaded on the targeted eUICC.
   The target Profile is owned by the requesting Operator or an Operator that had
    granted a PLMA that authorises the requesting M2M SP to perform the operation
    “EnableProfile” on a Profile that matches the criteria of the PLMA (see section 5.7.1.1
    for the detail of the matching of the criteria).
      The target Profile is in Disabled state
      The POL2 of the target Profile and the POL2 of the currently Enabled Profile allow the
       enabling.

The SM-SR MAY provide additional verifications.

In case one of these conditions is not satisfied, the SM-SR SHALL refuse the function request and return a ‘Function execution status’ indicating ‘Failed’ with the relevant status code (see table below).

The SM-SR receiving this request SHALL process it according to “Profile Enabling” procedure described in the section 3.2 of this specification.

This function may return:
     A ‘Function execution status’ with ‘Executed- Success’ indicating that the Profile has
        been enabled on the eUICC.
     A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
        5.1.6.4
     A ‘Function execution status’ indicating ‘Failed’
            with a status code indicating a Unknown eUICC
            with a status code indicating a Unknown ICCID
     With a status code as defined in section 5.1.6.4 or a specific status code as defined in
        the table below.

Additional input data:

Input data name                 Description                   Type    No. MOC
                  Identification of the targeted eUICC.
Eid                                                            EID    1     M
                  See section 5.1.1.1 for type description.
                  Identification of the Profile to enable.
Iccid                                                         ICCID   1     M
                  See section 5.1.1.1 for type description.

Table 184: Enable Profile Additional Input Data

Additional output data:

Output data name                                       Description                                    Type     No. MOC
                  Contains the detailed error returned by the eUICC in case the function execution
                                                                                                       Hex
euiccResponseData failed on eUICC. The response data is defined in ES5 depending of the               binary
                                                                                                               1   O
                  requested function.

Table 185: Enable Profile Additional Output Data

Specific status codes

Subj ect               Reason
            Subj ect                 Reason                                          Description
  code                 code
                                               Indicates that the eUICC, identified by this EID, is unknown to the
8.1.1    EID       3.9   Unknown               function provider.
                                              Indicates that the Profile change procedure couldn’t complete after
8.2     Profile   5.1   Inaccessible          enabling the target Profile, and the Profile change was rolled -back on the
                                              eUICC,
         Profile                               Indicates that the Profile identified by this ICCID is unknown to the
8.2.1              3.9   Unknown
         ICCID                                 function provider.
                                               Indicates that the Profile identified by this ICCID is known to the function
         Profile
8.2.1              3.4   Invalid destination   provider but installed on another eUICC than the one identified by the
         ICCID
                                               function caller.
         Profile
8.2.1              3.5   Invalid Transition    Indicates that the Profile was already Enabled
         ICCID
         Profile         Not        Allowed Indicates that the function caller is not allowed to perform this function on
8.2.1              1.2
         ICCID           (Authorisation)    the target Profile.
8.2.2    POL1      3.8   Refused               The POL1 of one the impacted Profiles don’t allow this operation.
8.2.3    POL2      3.8   Refused               The POL2 of one the impacted Profiles don’t allow this operation.
8.2.7    PLMA      3.8   Refused               No PLMA allows the M2M SP to execute this operation.
                                              Error during execution of the enabling command on the eUICC. In that
8.4     ISD-R     4.2   Execution error       case, the output data “euiccResponseData contains the exact response
                                              coming from the eUICC.

Table 186: Enable Profile Specific Status Codes

5.5.6 Profile Disabling

Function name: DisableProfile

Related Procedures: Profile Disabling

Function group: Platform Management

Function Provider: SM-SR

Description: This function allows the Operator or the M2M SP to request a Profile Disabling to the SM-SR in charge of the management of the targeted eUICC; eUICC being identified by its EID.

On reception of the function request, the SM-SR SHALL perform the following minimum set of verifications:

     The SM-SR is responsible for the management of the targeted eUICC.
     The Profile identified by its ICCID is loaded on the targeted eUICC.
     The target Profile is owned by the requesting Operator, or an Operator that had
      granted a PLMA that authorises the requesting M2M SP to perform the operation
      “DisableProfile” on a Profile that matches the criteria of the PLMA (see section 5.7.1.1
      for the detail of the matching of the criteria)
     The target Profile is in Enabled state
     The POL2 of the target Profile allows the disabling.

This function may return:

   A ‘Function execution status’ with ‘Executed-Success’ indicating that the Profile has
    been disabled on the eUICC.
   A ‘Function execution status’ with ‘Executed-WithWarning’, with a status code as
    defined below, indicating that the Profile has been disabled on the eUICC, and
    deleted after application of a POL1 or POL2 rule.
   A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
    5.1.6.4
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
    section 5.1.6.4 or a specific status code as defined in the table below

Additional input data:

Input data name                 Description                    Type    No. MOC
                  Identification of the targeted eUICC.
eid                                                             EID     1     M
                  See section 5.1.1.1 for type description.
                  Identification of the Profile to disable.
iccid                                                          ICCID    1     M
                  See section 5.1.1.1 for type description.

Table 187: Disable Profile Additional Input Data

Additional output data:
                                                                                                                     No. MOC
 Output data name                                      Description                                         Type
                  Contains the detailed error returned by the eUICC in case the function execution                   1     O
                                                                                                   Hex
euiccResponseData failed on eUICC. The response data is defined in ES5 depending of the requested binary
                  function.

Table 188: Disable Profile Additional Output Data

Specific status codes

Subject                Reason
            Subject                 Reason                                          Description
 code                   code
                                                 Indicates that the target Profile can’t be disabled. (for example the Profile is
8.1       UICC         3.8       Refused         the only Profile in the eUICC)
                                                 Indicates that the Profile change procedure couldn’t complete after enabling
8.2       Profile      5.1       Inaccessible    the Profile with the Fall -Back Attribute set, and the Profile change was
                                                 rolled-back on the eUICC,
                                                 Indicates that the eUICC, identified by this EID, is unknown to the function
8.1.1     EID          3.9       Unknown
                                                 provider.
          Profile                                Indicates that the Profile identified by this ICCID is unknown to the function
8.2.1                  3.9       Unknown
          ICCID                                  provider.
                                                 Indicates that the Profile identified by this ICCID is known to the function
          Profile                Invalid
8.2.1                  3.4                       provider but installed on another eUICC than the one identified by the
          ICCID                  destination
                                                 function caller.
          Profile                Invalid
8.2.1                  3.5                       Indicates that the Profile was already Disabled
          ICCID                  Transition
Subject               Reason
            Subject               Reason                                        Description
 code                  code
          Profile              Not Allowed Indicates that the function caller is not allowed to perform this function on
8.2.1                 1.2
          ICCID                (Authorisation) the target Profile.
                                               The POL1 of the target Profile has triggered its deletion after disabling it
                               Related
8.2.2     POL1        3.6                      This status code SHALL only be sent along Status =”Executed-
                               Object Exists
                                               WithWarning”
8.2.2     POL1        3.8      Refused         The POL1 of the target Profile doesn’t allow this operation.
                                               The POL2 of the target Profile has triggered its deletion after disabling it
                               Related
8.2.3     POL2        3.6                      This status code SHALL only be sent along Status =”Executed -
                               Object Exists
                                               WithWarning”
8.2.3     POL2        3.8      Refused         The POL2 of the target Profile doesn’t allow this operation.
8.2.7     PLMA        3.8      Refused         No PLMA allows the M2M SP to execute this operation.
                                               Error during execution of the disabling command on the eUICC. In that case,
                               Execution
8.4       ISD-R       4.2                      the output data “euiccResponseData” contains the exact response coming
                               error
                                               from the eUICC.

Table 189: Disable Profile Specific Status Codes

5.5.7 Delete a Profile

Function name: DeleteProfile

Related Procedures: Profile and ISD-P Deletion

Function group: Platform Management

Function Provider: SM-SR

Description: This function allows the Operator or the M2M SP to request deletion of the target ISD-P with the Profile to the SM-SR in charge of the management of the targeted eUICC; eUICC being identified by its EID.

On reception of the function request, the SM-SR SHALL perform the following minimum set of verifications:

   The SM-SR is responsible for the management of the targeted eUICC.
   The Profile identified by its ICCID is loaded on the targeted eUICC.
   The POL2 of the target Profile allows the deletion.
   The target Profile is not the Profile having the Fall-Back Attribute.
   The target Profile is owned by the requesting Operator, or an Operator that had
    granted a PLMA that authorises the requesting M2M SP to perform the operation
    “DeleteProfile” on a Profile that matches the criteria of the PLMA (see section 5.7.1.1
    for the detail of the matching of the criteria).

The SM-SR MAY provide additional verifications.

In case one of these conditions is not satisfied, the SM-SR SHALL refuse the function request and return a ‘Function execution status’ indicating ‘Failed’ with the relevant status code (see table below).

The SM-SR receiving this request SHALL process it according to “ISD-P Deletion” procedure described in the section 3.6 of this specification.

In case the target Profile is “Enabled”, the SM-SR SHALL automatically disable it before executing the deletion. This function is described in section 4.1.1.3.

This function may return:

      A ‘Function execution status’ with ‘Executed- Success’ indicating that the Profile has
       been deleted on the eUICC.
      A 'Function execution status' with 'Executed- WithWarning' indicating that the Profile
       has been deleted on the eUICC, with a status code as defined in section 5.1.6.4 or a
       specific status code as defined in the table below
      A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
       5.1.6.4
      A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
       section 5.1.6.4 or a specific status code as defined in the table below.

Additional input data:

Input data name                  Description                  Type    No. MOC
                  Identification of the targeted eUICC.
eid                                                            EID     1    M
                  See section 5.1.1.1 for type description.
                  Identification of the Profile to delete.
iccid                                                         ICCID 1       M
                  See section 5.1.1.1 for type description.

Table 190: Delete Profile Additional InputDdata

Additional output data:

Output data name                                        Description                                   Type     No. MOC
                     Contains the detailed error returned by the eUICC in case the function execution
euiccResponseData                                                                                     Byte[]   1   O
                          failed on eUICC

Table 191: Delete Profile Additional Output Data

Specific status codes

Subject              Reason
           Subject                Reason                                            Description
 code                 code
                                                  Indicates that the eUICC, identified by this EID, is unknown to the function
8.1.1   EID         3.9     Unknown               provider.
        Profile                                   Indicates that the Profile identified by this ICCID is unknown to the function
8.2.1               3.9     Unknown
        ICCID                                     provider.
                                                  Indicates that the Profile identified by this ICCID is known to the function
        Profile
8.2.1               3.4     Invalid destination   provider but installed on another eUICC than the one identified by the
        ICCID
                                                  function caller.
        Profile             Not       Allowed     Indicates that the function caller is not allowe d to perform this function on
8.2.1               1.2
        ICCID               (Authorisation)       the target Profile.
        Profile                                   Indicates that the Profile cannot be deleted because it is the last Profile of
8.2.1               3.8     Refused
        ICCID                                     the eUICC or the Fall -Back Profile.
8.2.2   POL1        3.8     Refused               The POL1 of the Profile doesn’t allow this operation.
8.2.3   POL2        3.8     Refused               The POL2 of the Profile doesn’t allow this operation.
8.2.7   PLMA        3.8     Refused               No PLMA allows the M2M SP to execute this operation.
                           Not   Present     /   The target ISD-P was not found on this eUICC (in this case the Function
8.3    ISD-P     4.6       Missing               Execution Status SHALL be ‘Executed- WithWarning’)
                                                 Error during execution of the deletion (or disabling) command on the
8.4    ISD-R       4.2     Execution error       eUICC. In that case, the output data “euiccResponseData” contains the
                                                 exact response coming from the eUICC.

Table 192: Delete Profile Specific Status Codes

NOTE:in case Profile disabling is performed automatically before deletion, this function MAY raise any status code coming from the execution of the Profile disabling function defined in section 5.5.6.

5.5.8 Prepare SM-SR Change

Function name: PrepareSMSRChange

Related Procedures: SM-SR Change

Function group: eUICC Management

Function Provider: SM-SR

Description: This function allows the Initiator to request to a new SM-SR to prepare for a change for an eUICC identified by its EID.

The check is used to give the opportunity to the new SM-SR to ensure that any necessary business agreement is in place.

This function may return:

     A ‘Function execution status’ with ‘Executed- Success’ indicating that the
      PrepareSMSRChange function has been successfully executed on the SM-SR as
      requested by the function caller.
     A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
      5.1.6.4
     A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
      section 5.1.6.4 of a specific status code as defined in the table below.

Additional input data:

Input data name                 Description                   Type No. MOC
                  provide the EID of the eUICC
eid                                                           EID   1    M
                  See section 5.1.1.1 for type description.
                  Identification of the current SM -SR.
currentSMSRid                                                 OID   1    M
                  See section 5.1.1.1 for type description.

Table 193: Prepare SM-SR Change Additional Input Data

Table 194: Void

Table 195: Void

Specific status codes

Subj ect                       Reason
                 Subj ect                        Reason                                     Description
 Code                           code
                                          Condition Of Use Not Indicates that function provider is not capable of managing the
  1.2      Function Provider     3        satisfied            eUICC identified by this EID,
                                                                  The new SM-SR doesn’t know or have access to the current
8.7      SM-SR                 1.1      Unknown
                                                                  SM-SR managing this eUICC
                                         Already    in      Use    Indicates that the eUICC identified by this EID is already
8.1.1     EID                   3.3
                                         (Uniqueness)              managed by this SM-SR.

Table 196: Prepare SM-SR Change Specific Status Codes

5.5.9 SM-SR Change

Function name: SMSRChange

Related Procedures: SM-SR Change

Function group: eUICC Management

Function Provider: SM-SR

Description: This function allows the initiator to request to the current SM-SR to change for a specific eUICC identified by its EID.

The SM-SR receiving this request SHALL process it according to the “SM-SR Change” procedure described in GSMA Remote Provisioning Architecture for Embedded UICC [1].

This function may return:

     A ‘Function execution status’ with ‘Executed-Success’ indicating that the function has
      been successfully executed by the function provider as requested by the func tion
      caller. In this case, the eUICC is unambiguously managed by the new SM-SR (SM-
      SR2).
    A ‘Function execution status’ with ‘Executed-WithWarning’ indicating either:
   that the eUICC has been successfully transferred to the new SM-SR, but
    additional configuration has not completed and may need to be done again. In this
    case, the eUICC is unambiguously managed by the new SM-SR (SM-SR2), but
    the new SM-SR SHALL perform such configuration operations automatically at a
    later point in time
   or that the eUICC was already managed by the new SM-SR (SM-SR2). This
    happens when this is the second attempt to perform the SM-SR Change, after the
    first attempt expired whereas it was already successful from the point of view of
    the new SM-SR.
    A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
     section 5.1.6.4 of a specific status code as defined in the Specific status code table
     below, to indicate that the procedure has failed or expired before the effective transfer
     of OTA management to the new SM-SR. In this case, the eUICC is still managed
     unambiguously by the current SM-SR (SM-SR1).
    A ‘Function execution status’ indicating ‘Expired’ with the status code as defined in
     section 5.1.6.4, indicating that the procedure has expired before confirming the
     proper transfer.

Additional input data:

Input data name                Description                    Type   No. MOC
                  Identification of the targeted eUICC.
eid                                                           EID     1     M
                  See section 5.1.1.1 for type description.
                  Identification of the new SM -SR.
targetSMSRid                                                  OID     1     M
                  See section 5.1.1.1 for type description.

Table 197: SM-SR Change Additional Input Data

Specific status codes

In addition to the status codes returned by ES7.handoverEUICC, this function can return the following specific status codes:

Subj ect                         Reason
               Subj ect                       Reason                                       Description
  Code                            code
1.6        Function             5.3       Time to live       The function execution request has expired (end of validity period
                                          expired            has been reached). This may be because the server had no time to
                                                             execute the function or because the function was requesting a
                                                             remote communication with the eUICC which was not present on the
                                                             network during all the validity period.
                                                             If this status code is returned when ‘Execution Status‘ is ‘Failed’, this
                                                             means the current SM-SR (SM-SR1) is still managing the eUICC.
1.6        Function             4.5       Operation          The function is the second attempt to transfer the same eUICC to the
                                          Already            same new SM-SR after a previous attempt has expired, and the
                                          Processed          previous attempt had indeed succeeded from the point of view of the
                                                             new SM-SR. In this case the Execution-Status SHALL be ‘Executed-
                                                             WithWarning’
8.1.1       EID              1.1    Unknown           Indicates that the EID , is unknown to the function provider
                                    Not Allowed
8.1         eUICC            1.2                      Function requester is not allowed to manage the eUICC
                                    (Authorisation)
8.1         eUICC            4.4    Busy              Other operations pending on the eUICC
8.4         ISD-R            4.2    Execution error   Error during the creation of a new key set at the ISD-R level
            eUICC
            Certificate             Certificate
8.5.2                        6.3                      ECASD Certificate Expired
            Authority               Expired
            Certification
8.7         SM-SR            3.9    Unknown           The targetSMSRid is unknown

Table 198: SM-SR Change Specific Status Codes

5.5.10 Notify a Profile is Disabled

Function name: HandleProfileDisabledNotification

Related Procedures: Profile Download and Installation, Profile Enabling, Fall-Back Activation Procedure, Profile Enabling via M2MSP, Profile Disabling via M2MSP, Profile Enabling via SM-DP

Function group: Platform Management

Notification handler/recipient: Operator

Description: This function SHALL be called to notify that the Profile identified by its ICCID has been disabled on the eUICC identified by its EID, if and only if:

   The recipient of the notification is the Operator owning the Profile and has not set an
    ONC to discard those notifications,
    or
   The recipient of the notification is an M2M SP (including, another Operator that is not
    the owner of the Profile), and the Operator owner of the Profile has granted the M2M
    SP with a PLMA authorising the Operation “HandleProfileDisabledNotification”.

ICCID may be not enough to identify right address of recipient, SM-SR should map it internally to Operator notification endpoint.

This notification also conveys the date and time specifying when the operation has done.

In case multiple handlers are served, the SM-SR SHOULD ensure completionTimestamp to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:

Input data name                               Description                                Type     No. MOC
                      Identification of the targeted eUICC.
eid                                                                                          EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile that has been disabled.
iccid                                                                                       ICCID     1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                        DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 199: Handle Profile Disabled Notification Additional Input Data

5.5.11 Notify a Profile is Enabled

Function name: HandleProfileEnabledNotification

Related Procedures: Profile Disabling, Profile Disabling via SM-DP, Fall-Back Activation Procedure, Profile Enabling via M2M SP, Profile Disabling via M2M SP

Function group: Platform Management

Notification handler/recipient: Operator

Description: This function SHALL be called to notify that the Profile identified by its ICCID has been enabled on the eUICC identified by its EID, if and only if:

     The recipient of the notification is the Operator owning the Profile and has not set an
      ONC to discard those notifications
      Or
     The recipient of the notification is an M2M SP (including, another Operator that is not
      the owner of the Profile), and the Operator owner of the Profile has granted the M2M
      SP with a PLMA authorising the Operation “HandleProfileEnabledNotification”.

ICCID may be not enough to identify right address of recipient, SM-SR should map it internally to Operator notification endpoint.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure completionTimestamp to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:

Input data name                               Description                                Type     No. MOC
                      Identification of the targeted eUICC.
eid                                                                                          EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile that has been disabled.
iccid                                                                                            ICCID     1       M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                         DATETIME       1       M
                      See section 5.1.1.1 for type description.

Table 200: Handle Profile Enabled Notification Additional Input Data

5.5.12 Notify a SM-SR Change

Function name: HandleSMSRChangeNotification

Related Procedures: SM-SR Change

Function group: eUICC Management

Notification handler/recipient: Operator

Description: This function SHALL be called for notifying each Operator owning a Profile hosted in the eUICC, identified by its EID, that the SM-SR has changed. The notification is sent by the new SM-SR.

This notification also conveys the date and time specifying when the operation has been done.

This notification is not related to a particular Profile. It is up to the notification recipient to perform any action related to each Profile that is deployed on this eUICC.

Additional input data:

Input data name                                        Description                                       Type       No. MOC
                       The relevant part of the eUICC Information Set linked with the Operator
                       owning the Profile hosted in the eUICC.
eis                                                                                                       EIS        1       M
                       See         section        5.1.1.1         for       type        description.
                       The list of EIS data fields that SHALL be included is defined in Annex E.
                    Indication of the date/time when the operation has been performed.
completionTimestamp See section 5.1.1.1 for type description.                                           DATETIME      1       M

Table 201: Handle SM -SR Change Notification Additional Input Data

Additional output data:

No output data is expected in response to this notification.

5.5.13 Notify a Profile Deletion

Function name: HandleProfileDeletedNotification

Related Procedures: Profile enabling, Profile Enabling via SM-DP, Profile Enabling via M2M SP, Profile Disabling via M2M SP, Profile and ISD-P Deletion via M2M SP

Function group: Platform Management

Notification handler/recipient: Operator

Description: This function SHALL be called to notify that the Profile identified by its ICCID has been deleted on the eUICC identified by its EID, if and only if:

     The recipient of the notification is the Operator owning the Profile and has not set an
      ONC to discard those notifications
      or
     The recipient of the notification is an M2M SP (including, another Operator that is not
      the owner of the Profile), and the Operator owner of the Profile has granted the M2M
      SP with a PLMA authorising the Operation “HandleProfileDeletedNotification”.

ICCID may be not enough to identify right address of recipient; SM-SR should map it internally to Operator notification endpoint.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure ‘completionTimestamp’ to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:

Input data name                               Description                                Type     No. MOC
                      Identification of the targeted eUICC.
eid                                                                                          EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile that has been deleted.
iccid                                                                                       ICCID     1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                        DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 202: Handle Profile Deleted Notification Additional Input Data

5.5.14 Notify a Profile Download

Function name: HandleProfileDownloadedNotification

Related Procedures: Profile Download

Function group: Profile Management

Notification handler/recipient: M2M SP

Description: This function SHALL be called to notify that the Profile identified by its ICCID has been downloaded on the eUICC identified by its EID.

The SM-SR SHALL inspect the PLMAs that apply to this Profile, and only send this notification to recipients which have a PLMA that includes the authorisation to receive this notification.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure ‘completionTimestamp’ to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:

Input data name                              Description                                 Type     No. MOC
                      Identification of the targeted eUICC.
eid                                                                                          EID      1     M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile that has been downloaded.
iccid                                                                                       ICCID     1     M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                        DATETIME   1     M
                      See section 5.1.1.1 for type description.

Table 5514: Handle Profile Downloaded Notification Additional Input Data

5.5.15 Notify the Change of Policy Rules of a Profile

Function name: HandlePolicyRulesUpdatedNotification

Related Procedures: POL2 Update, POL2 Update via SM-DP

Function group: Profile Management

Notification handler/recipient: M2M SP

Description: This function SHALL be called to notify an M2M SP that the Policy Rules have been updated on the Profile identified by its ICCID on the eUICC identified by its EID.

The SM-SR SHALL inspect the PLMAs that apply to this Profile, and only send this notification to an M2M SP that has been granted a PLMA by the Operator owner of the Profile for the authorised operation “HandlePolicyRuleUpdatedNotification”.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure ‘completionTimestamp’ to be equal for every message.

What is performed by the M2M SP receiving this notification is out of scope of this specification.

Additional input data:

Input data name                                  Description                                   Type       No. MOC
                      Identification of the targeted eUICC.
Eid                                                                                                EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile whose POL2 has been updated.
iccid                                                                                             ICCID     1   M
                      See section 5.1.1.1 for type description.
                      Value of the POL2 after being updated by the Operator owning the Profile
Pol2                                                                                              POL2      1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                              DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 5515: Handle Policy Rules Updated Notification Additional Input Data

5.5.16 Notify a PLMA Setting

Function name: HandleSetPLMANotification

Related Procedures: Set Profile Lifecycle Management Authorisation, Set Profile Lifecycle Management Authorisation via SM-DP

Function group: Platform Management

Notification handler/recipient: M2M SP

Description: This function SHALL be called to notify an M2M SP that a PLMA concerning this M2M SP has been set or updated.

This notification also conveys the date and time specifying when the operation has been done. In case of multiple handlers are served the SM-SR SHOULD ensure ‘completionTimestamp’ to be equal for every message.

What is performed by the M2M SP receiving this notification is out of scope of this specification.

Additional input data:

Input data name                                     Description                                   Type     No. MOC
                       The specification of the PLMA that now applies on a Profile Type.
                       Information about the Profile Type are contained in the PLMA structure       PLMA     1   M
plma
                       See section 5.1.1.2.14 for type description
                       Indication of the date/time when the operation has been performed.
completionTimestamp                                                                               DATETIME   1   M
                       See section 5.1.1.1 for type description.

Table 5516-A: Handle PLMA Changed Notification Additional Input Data

5.5.17 Retrieving Authorisations of M2M SP to Access Profiles

Function name: GetPLMA

Related Procedures: Retrieve Profile Lifecycle Management Authorisation by Operator , Retrieve Profile Lifecycle Management Authorisation by M2M SP

Function group: Profile Management

Function Provider: SM-SR

Description:

This function allows the Operator owner of Profiles to retrieve the list of PLMAs applicable to a certain Profile, or a certain Profile Type, or for a certain M2M SP.

The same function can also be used by the M2M SP to retrieve the list of PLMAs granted to this M2M SP, and applicable to a certain Profile, or a certain Profile Type.

The SM-SR receiving this request SHALL verify the requester is allowed to retrieve such information, and return the list of all PLMAs applicable to the specified search criterion:

   If the requester is the owner of the targeted Profiles, the authorisation is implied.
   If the requester is an M2M SP (including, another Operator that is not the owner of
    the targeted Profiles), the list of PLMAs is only returned if at least a PLMA exist for
    this M2M SP and for the targeted Profile or Profile Type

If this verification fails, the SM-SR SHALL terminate the request and return a response with the ‘Function execution status’ indicating ‘Failed’, and no PLMA.

Otherwise, the SM-SR SHALL return the complete list of all PLMAs applicable to the specified search criterion; if the search criterion is on a specific Profile or Profile Type, this includes even PLMAs that are granted to an M2M SP that is not the function requester.

In case the list of PLMAs is very long, the SM-SR MAY truncate the result. The caller can then issue another call to getPLMA with more restrictive criteria.

NOTE The order of the PLMAs returned in the truncated list is implementation-dependent.

This function may return:

    A ‘Function execution status’ with ‘Executed- Success’, and additional output data
     providing the PLMAs.
    A ‘Function execution status’ with ‘Executed-WIthWarning’, to indicate that the result
     was truncated, plus additional output data providing part of the list of applicable
     PLMAs.
    A ‘Function execution status’ indicating ‘Failed’ if the requester was not allowed to
     request this information.

Additional input data:

Input data name                                         Description                                       Type     No.    MOC
                      Identification of the Profile type for which PLMAs are searched
profileType                                                                                               String     1       C
                      Identification of the M2M SP for which PLMAs are searched
m2m-sp-id                                                                                                   OID      1       C
                      Identification of one specific Profile
iccid                                                                                                     ICCID      1       C
mno-id                Identification of the Operator owning the Profiles to be matched (this input
                                                                                                            OID      1       C
                      datum SHALL be present only in case the search criterion is a Profile Type).
                      See section 5.1.1.1 for type description.

Table 5517-A: GetPLMA Additional Input Data

One and only one of the input data profileType, m2m-sp-id and iccid SHALL be present.

Additional output data:

Output data name                          Description                       Type    No. MOC
                     The list of PLMAs that match the search criterion
plma                                                                       PLMA     N      M
                     See section 5.1.1.2.14 for type description.

Table 5517-B: RetrievePLMA Additional Output Data

Specific status codes:

Subj ect                 Reason
            Subj ect                    Reason                                         Description
 code                    code
                                                         Indicates that the Operator or M2M SP which called this function is not
           Function                Not Allowed           doesn’t have a PLMA granted that applies to the targeted Profile or
  1.1                     1.2
           requester               (Authorisation)       Profile type (including, if the targeted Profile or Profile type is unknown
                                                         to this SM-SR)
                                                       Indicates that the M2M SP specified in the search criterion is unknown
8.9      M2M SP         1.1      Unknown               to this SM-SR
                                                       Indicates that the Operator, addressed by the mno -id in the PLMA, is
8.10     Operator       1.1      Unknown               unknown.

Table 5517-C: GetPLMA Specific Status Codes

5.5.18 Setting the Emergency Profile Attribute

Function name: SetEmergencyProfileAttribute

Related Procedures: Emergency Profile Attribute Management

Function group: Platform Management

Function Provider: SM-SR

Description:

This function allows an Operator or an M2M SP authorised by the Operator via PLMA to request the setting of the Emergency Profile Attribute on the targeted Profile to the SM-SR in charge of the management of the targeted eUICC, eUICC being identified by its EID.

The SM-SR SHALL verify that the request is

     Either sent by an Operator owning the targeted Profile
      or
     Sent by an M2M SP, but the Operator owning the targeted Profile has granted a
      PLMA allowing the operation “SetEmergencyProfileAttribute” to the M2M SP
      requesting the operation.

If one Profile currently has the Emergency Profile Attribute set, the SM-SR SHALL verify that the Operator owning the Profile with the Emergency Profile Attribute set has granted a PLMA authorising the operation “UnsetEmergencyProfileAttribute” to the Operator requesting the operation.

The SM-SR MAY provide additional verifications.

The SM-SR receiving this request SHALL process it according to “Emergency Profile Attribute Management” procedure described in sections 3.25 and 3.26 of this specification.

After setting the Emergency Profile Attribute, the SM-SR SHALL add or update the AdditionalProperty ‘gsma.ESIM.EmergencyProfile.AID’ of the EIS.

This function may return:

      A ‘Function execution status’ with ‘Executed- Success’ indicating that the Emergency
       Profile Attribute has been set on the targeted Profile.
      A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
       5.1.6.4
      A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
       section 5.1.6.4 of a specific status code as defined in the table here after.

Additional input data:

Input data name                                Description                                    Type     No.   MOC
eid               Identification of the targeted eUICC.                                       EID       1    M
                  See section 5.1.1.1 for type description.
                  Identification of the Profile to get the Emergency Profile Attribute set.
iccid                                                                                         ICCID     1    M
                  See section 5.1.1.1 for type description.

Table 5518-A: Set Emergency Profile Attribute Additional Input Data

Additional output data:

Output data name                                    Description                                         Type        No. MOC
                  Contains the detailed error returned by the eUICC in case the function
euiccResponseData execution failed on eUICC. The response data is defined in Hexadecimal                             1    O
                                                                                         String
                  ES5.SetEmergencyProfileAttribute.

Table 5518-B: Set Emergency Profile Attribute Additional Output Data

Specific status codes

Subj ect                Reason
             Subj ect              Reason                                       Description
 code                   code
                                               Indicates that the eUICC, identified by this EID, is unknown to the function
 8.1.1      EID          3.9     Unknown
                                               provider.
           Profile                            Indicates that the Profile identified by this ICCID is unknown to the function
8.2.1                   3.9     Unknown
           ICCID                              provider.
                                              Indicates that the Profile identified by this ICCID is known to the function
           Profile              Invalid
8.2.1                   3.4                   provider but installed on another eUICC than the one identified by the function
           ICCID                destination
                                              caller.
8.2.7      PLMA         3.8     Refused       No PLMA allows the M2M SP to execute this operation.
                                             Error during execution of the command on the eUICC. In that case, the output
                               Execution
8.4       ISD-R        4.2                   data “euiccResponseData” contains the exact response coming from the
                               error
                                             eUICC.

Table 5518-C: Set Emergency Profile Attribute Specific Status Codes

5.5.19 Notifying the Emergency Profile Attribute setting

Function name: HandleEmergencyProfileAttributeSetNotification

Related Procedures: Emergency Profile Attribute Management, Emergency Profile Attribute Management via M2M SP

Function group: Profile Management

Notification handler/recipient: Operator / M2M SP

Description: This function SHALL be called to notify that the Emergency Profile Attribute has been set on the Profile identified by its ICCID on the eUICC identified by its EID.

The SM-SR SHALL send this notification to all Operator and M2M SP servers that match one or the other of the following conditions:

      The Operator that owns the Profile, and the Operator has not set an ONC to discard
       such notifications (see section 3.21)
      The M2M SP, where the Operator owner of the Profile has granted the M2M SP with
       a PLMA authorising this Operation “HandleEmergencyProfileAttributeSetNotification”.
      Any Operator having a Profile on this eUICC. In this case identification of the Profile
       that has the Emergency Profile Attribute set and Identification of the Operator owner
       of the Profile that has the Emergency Profile Attribute set are optional.

ICCID may be not enough to identify right address of recipient, SM-SR should map it internally to Operator notification endpoint.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure completionTimestamp to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
    Input data name                                  Description                                       Type     No. MOC
                      Identification of the targeted eUICC.
eid                                                                                                   EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile that has the Emergency Profile Attribute set.
iccid                                                                                                ICCID     1   C
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                 DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 5519: Handle Emergency Profile Attribute Set Notification Additional Input Data

5.5.20 Notifying the Emergency Profile Attribute Unsetting

Function name: HandleEmergencyProfileAttributeUnsetNotification

Related Procedures: Emergency Profile Attribute Management, Emergency Profile Attribute Management via M2M SP

Function group: Profile Management

Notification handler/recipient: Operator / M2M SP

Description: This function SHALL be called to notify that the Emergency Profile Attribute has been unset on the Profile identified by its ICCID on the eUICC identified by its EID.

The SM-SR SHALL send this notification to all Operator and M2M SP servers that match one or the other of the following conditions:

    The Operator that owns the Profile, and the Operator has opted to receive such
     notifications (see section 3.21)
    The M2M SP, and the Operator owner of the Profile has granted the M2M SP with a
     PLMA authorising this Operation
     “HandleEmergencyProfileAttributeUnsetNotification”.

ICCID may be not enough to identify right address of recipient, SM-SR should map it internally to Operator notification endpoint.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served, the SM-SR SHOULD ensure completionTimestamp to be equal for every message.

What is performed by the Operator receiving this notification is out of scope of this specification.

Additional input data:
   Input data name                                  Description                                        Type     No. MOC
                      Identification of the targeted eUICC.
eid                                                                                                     EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile that has the Emergency Profile Attribute unset.
iccid                                                                                                  ICCID     1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                   DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 5520: Handle Emergency Profile Attribute Unset Notification Additional Input

Data

5.5.21 Setting the Fall-Back Attribute

Function name: SetFallBackAttribute

Related Procedures: Fall-Back Attribute Management

Function group: Profile Management

Function Provider: SM-SR

Description:

This function allows the Operator owner of the Profile or an M2M SP authorised by the Operator owner of the Profile, to request the SM-SR to set the Fall-Back Attribute on a Profile in a specified eUICC, eUICC being identified by its EID. On reception of this request, the SM-SR SHALL perform the following minimum set of verifications:

    The SM-SR is responsible for the management of the targeted eUICC.
    The Profile identified by its ICCID is loaded on the targeted eUICC.
    The target Profile is owned by the requesting Operator, or by an Operator that had
      granted a PLMA that authorises the requesting M2M SP to perform the operation
      “setFallbackAttribute” on a Profile that matches the criteria of the PLMA (see section
      5.7.1.1 for the detail of the matching of the criteria)
    The Operator owning the Profile which currently has the Fall-Back Attribute set has
      granted a PLMA that authorises the requesting Operator or M2M SP to perform the
      operation “UnsetFallBackAttribute”, and that the Profile that currently has the Fall-
      Back Attribute set matches the criteria of the PLMA (see section 5.7.1.1 for the detail
      of the matching of the criteria).
The SM-SR MAY provide additional verifications.

The SM-SR receiving this request SHALL process it according to “Fall-Back Attribute Management” procedures described in section 3.27 and 3.29 of this specification.

This function may return:

    A ‘Function execution status’ with ‘Executed- Success’ indicating that the Fall-Back
     Attribute has been set on the targeted Profile.
      A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
       5.1.6.4
      A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
       section 5.1.6.4 of a specific status code as defined in the table here after.

Additional input data:

Input data name                                 Description                                   Type     No.   MOC
eid                 Identification of the targeted eUICC.                                      EID      1    M
                    See section 5.1.1.1 for type description.
                    Identification of the Profile on which to set the Fall -Back Attribute.
iccid                                                                                         ICCID     1    M
                    See section 5.1.1.1 for type description.

Table 5521-A: Set Fall-Back Attribute Additional Input Data

Additional output data:

Output data name                                       Description                                             Type     No. MOC
                  Contains the detailed error returned by the eUICC in case the function
                                                                                         Hexadecimal
euiccResponseData execution failed on eUICC. The response data is defined in                                               1   O
                                                                                         String
                  ES5.SetFallBackAttribute.

Table 5521-B: Set Fall-Back Attribute Additional Output Data

Specific status codes

Subj ect                    Reason
                 Subj ect               Reason                                           Description
 code                       code
                                                      Indicates that the eUICC, identified by this EID, is unknown to the function
 8.1.1        EID            3.9     Unknown
                                                      provider.
             Profile                                 Indicates that the Profile identified by this ICCID is unknown to the function
8.2.1                       3.9     Unknown
             ICCID                                   provider.
                                                     Indicates that the Profile identified by this ICCID is known to the function
             Profile                Invalid
8.2.1                       3.4                      provider but installed on another eUICC than the one identified by the function
             ICCID                  destination
                                                     caller.
                                                     The POL1 of a Profile on the targeted eUICC doesn’t allow this operation (see
8.2.2        POL1           3.8     Refused
                                                     Note).
8.2.7        PLMA           3.8     Refused          No PLMA allows the function requester to execute this operation.
                                                    Error during execution of the command on the eUICC. In that case, the output
                                   Execution
8.4         ISD-R          4.2                      data “euiccResponseData” contains the exact response coming from the
                                   error            eUICC.

Table 5521-C: Set Fall-Back Attribute Specific Status Codes

NOTE                 A POL1 may interfere with the Set Fall-Back Attribute operation in very
                     specific circumstances described in section 4.1.1.7

5.5.22 Notifying the Fall-Back Attribute is Set

Function name: HandleProfileFallBackAttributeSetNotification

Related Procedures: Fall-Back Attribute Management, Fall-Back Attribute Management via M2M SP

Function group: Profile Management

Notification handler/recipient: Operator or M2M SP

Description:

This function SHALL be called to notify the Operator and the M2M SP that the Fall-Back Attribute has been set on the Profile identified by its ICCID on the eUICC identified by its EID.

The SM-SR SHALL send this notification to:

    the Operator owning the Profile, if it has not set an ONC to not receive those
     notifications
    the M2M SP SP (including, another Operator that is not the owner of the Profile), if
     the Operator owner of the Profile has granted the M2M SP with a PLMA authorising
     the operation “HandleProfileFallBackAttributeSetNotification”

ICCID may be not enough to identify right address of recipient, the SM-SR should map it internally to Operator or M2M SP notification endpoint.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served the SM-SR SHOULD ensure completionTimestamp to be equal for every message.

What is performed by the Operator or M2M SP receiving this notification is out of scope of this specification.

Additional input data:
   Input data name                                    Description                                       Type     No. MOC
                      Identification of the targeted eUICC.
eid                                                                                                    EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile on which the Fall-Back Attribute has been set.
iccid                                                                                                 ICCID     1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                                  DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 5522: Handle Profile Fall-Back Attribute Set Notification Additional Input Data

5.5.23 Notifying the Fall-Back Attribute is Unset

Function name: HandleProfileFallBackAttributeUnsetNotification

Related Procedures: Fall-Back Attribute Management, Fall-Back Attribute Management via SM-DP, Fall-Back Attribute Management via M2M SP

Function group: Profile Management

Notification handler/recipient: Operator or M2M SP

Description:

This function SHALL be called to notify that the Fall-Back Attribute has been unset on the Profile identified by its ICCID on the eUICC identified by its EID.

The SM-SR SHALL send this notification to:

   the Operator owning the Profile, if it has not set an ONC to not receive those
    notifications
   the M2M SP SP (including, another Operator that is not the owner of the Profile), if
    the Operator owner of the Profile has granted the M2M SP with a PLMA authorising
    the operation “HandleProfileFallBackAttributeUnsetNotification”

ICCID may be not enough to identify right address of recipient, the SM-SR should map it internally to Operator or M2M SP notification endpoint.

This notification also conveys the date and time specifying when the operation has been done. In case multiple handlers are served the SM-SR SHOULD ensure completionTimestamp to be equal for every message.

What is performed by the Operator or M2M SP receiving this notification is out of scope of this specification.

Additional input data:
  Input data name                                     Description                                 Type     No. MOC
                      Identification of the targeted eUICC.
eid                                                                                               EID      1   M
                      See section 5.1.1.1 for type description.
                      Identification of the Profile on which the Fall-Back Attribute has been
                      unset.
iccid                                                                                            ICCID     1   M
                      See section 5.1.1.1 for type description.
                      Indication of the date/time when the operation has been performed.
completionTimestamp                                                                             DATETIME   1   M
                      See section 5.1.1.1 for type description.

Table 5523: Handle Profile Fall-Back Attribute Unset Notification Additional Input Data

5.6 ES7 (SM-SR – SM-SR) Interface Description

5.6.1 Create Additional Key Set

Function name: CreateAdditionalKeySet

Related Procedures: SM-SR Change

Function group: eUICC Management

Function Provider: current SM-SR

Description: This function enables a new SM-SR to request for a new key set to be created in the ISD-R for the eUICC identified by the EID. The new key set belongs the new SM-SR and is unknown to the current SM-SR.

The current SM-SR SHALL map this function onto the second STORE DATA command in the ES5.EstablishISDRKeySet (see section 4.1.1.8), using the following rules:

   The order of TLVs SHALL follow the order denoted in Table 44
   The following parameters of this command as defined in Table 42 are not provided by
    the new SM-SR and it is the current SM-SR’s responsibility to set these parameters
    as defined below.
   Scenario identifier SHALL be set to '03'
   Key Usage Qualifier SHALL be set to '10' (3 secure channel keys)
   Key Access SHALL no be present, meaning a default value of ‘00’ (The key may
    be used by the Security Domain and any associated Application)
   Key Type SHALL be set to ‘88’ (AES)
   Key Length SHALL be set to '10' (16 bytes)
   Key Identifier SHALL be set to '01'
   The length of Initial value of sequence counter SHALL be 0, meaning the
    sequence counter SHALL have its default value
   The SDIN (tag 45 in Table 44) SHALL be included if and only if the bit b3 of the byte
    of Parameter for Scenario #3 is set to 1. In this case, the value of this field SHALL be
    the value of the SDIN of the ISD-R
   The value of other parameters are provided by the new SM-SR.
NOTE         This command includes a signature that is computed by the new SM-SR.
             Structural differences, for example in the order of TLVs, would invalidate the
             signature as the eUICC would not be able to verify it. The rules above
             ensure that both SM-SR follow the same structure, and the same values,
             even for parameters not explicitly supplied by the new SM-SR.

This function may return:

   A ‘Function execution status’ with ‘Executed- Success’ indicating that the function has
    been successfully executed by the function provider as requested by the function
    caller.
   A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
    5.1.6.4
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
    section 5.1.6.4 or a specific status code as defined in the table below.

Additional input data:

Input data name                            Description                                Type                  No.     MOC
                         Identification of the targeted eUICC.
eid                                                                                      EID                  1         M
                         See 5.1.1.1 for type description.
                         The Key Version Number of the to-be-created                   Integer                1         M
keyVersionNumber
                         keyset.
                                                                                                                      O (see
initialSequenceCounter The initial value of the Sequence Counter of the                Integer                1       note 1)
                       keyset
Enumeration
 {ECC-256,
eccKeyLength             The length of the Elliptic Curve Cryptography keys.          ECC-354,                1         M
                                                                                      ECC-512,
                                                                                      ECC-521 }
                                                                                 Hexadecimal String
scenarioParameter        Scenario parameter as defined in Table 45                                            1         M
                                                                               representation of 1 Byte
                         Host ID as defined in Table 4-17 of the
                                                                                                                      C (see
hostId                                                                            Hexadecimal String          1
                         Amendment E of         GlobalPlatform 2.2     Card                                           note 2)
                         Specification [11]
ephemeralPublicKey       The ephemeral public key calculated by new SM-SR               Byte[]                1         M
                         The signature associated to the authenticate SM-SR
                         function.
signature                                                                         Hexadecimal String          1         M
                         The signature is computed off-card by the new SM-
                         SR SK.SR. ECDSA. See section 4.1.1.8

Table 203: Create Additional Key Set Additional Input Data

NOTE 1:the input argument initialSequenceCounter is kept for backwards-compatibility of the API, but the rules stated above imply that the current SM-SR SHALL ignore the value provided by the new SM-SR.

NOTE 2:According to Table 44, hostId SHALL only be present in the Second STORE DATA APDU of ISD-R key establishment when the bit b3, of the byte of Parameter for Scenario #3, is set to 1.

Additional output data:

Output data name                       Description                             Type             No. MOC
                   A random number generated in the SE for additional
derivationRandom entropy in the key derivation process                  Hexadecimal String      1       C
                   A Message Authentication Code (MAC)
Receipt                                                                 Hexadecimal String      1       M

Table 204: Create Additional Key Set Additional Output Data

NOTE:To avoid subliminal channel attacks, in case the execution Status is Failed or Expired, the SM-SR SHOULD return empty hexadecimal strings for derivation random and Receipt.

Specific status codes

Subj ect                  Reason
               Subj ect             Reason                                        Description
 code                      code
8.1.1         EID        1.1      Unknown     Indicates that the EID, is unknown to the function provider
                                 Execution   Error during the creation of the key set at the ISD-R level. In that case, the output
8.4         ISD-R      4.2      error       data “euiccResponseData contains the exact response coming from the eUICC.

Table 205: Create Additional Key Set Specific Status Codes

5.6.2 Handover eUICC Information

Function name: HandoverEUICC

Related Procedures: SM-SR Change

Function group: eUICC Management

Function Provider: SM-SR

Description: This function enables to request for the handover management of an eUICC represented by its eUICC Information Set (EIS).

The EIS contains the complete set of data including information about Profiles, audit trail, which is applicable for the SM-SR to manage the lifecycle of this eUICC

The function provider SHALL execute the function accordingly to the procedure detailed in section 3.8. The handover is only committed at the end of the successfully procedure execution. In particular, if one of the operations fails or expires before having verified the receipt, the function provider SHALL return an error (Function executio n status indicating ‘Failed’)

This function may return:

      A ‘Function execution status’ with ‘Executed- Success’ indicating that the Handover
       eUICC function has been successfully executed on the SM-SR as requested by the
       function caller.
      A ‘Function execution status’ with ‘Executed-WithWarning’ with a status code defined
       in the table below, indicating either:
     that the eUICC has been successfully transferred to the new SM-SR, but
      additional configuration has not completed and may need to be done again. The
      new SM-SR SHALL perform such operations automatically at a later point in time.
     or that the eUICC is already managed by the receiving SM-SR (SM-SR2). This
      may happen when this is the second attempt to perform the SM-SR Change, after
      the first attempt expired on the old SM-SR (SM-SR1), whereas it was already
      successful from the point of view of SM-SR2.
   A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
    5.1.6.4
   A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
    section 5.1.6.4 of a specific status code as defined in the table below.

Additional input data:

Input data
                                                     Description                                          Type   No.     MOC
  name
                 The eUICC Information Set of the eUICC
                                                                                                          EIS      1      M
eis              See section 5.1.1.1 for type description. The list of EIS data fields that SHALL be
                 included is defined in Annex E.

Table 206: Handover EUICC Additional Input Data

Specific status codes

In addition to the status codes returned by ES7.AuthenticateSMSR and ES7.CreateAdditionalKeyset, this function may return one of the following specific status codes:

Subj ect                           Reason
                    Subj ect                       Reason                                     Description
  code                                code
              Function                         Condition Of Use Indicates that function provider is not capable of managing the
   1.2                            3
              Provider                         Not satisfied    eUICC identified by this EID.
           External            1.1          Unknown             One Operator owning a Profile on this eUICC is unknown to or not
1.4        Resource                                             reachable from the new SM-SR
                                                              The function is the second attempt to transfer an eUICC to the same
                                                              new SM-SR, after a previous attempt had already succeeded from
                                            Operation Already the point of view of this SM -SR, whereas it had expired from the
1.6        Function            4.5                            point of view of the old SM-SR.
                                            Processed
                                                                In this case     the Execution-Status SHALL be ‘Executed-
                                                                WithWarning’.
                                                                 Indicates that the preparation step hasn’t been performed for the
8.1.1       EID                 1.1          Unknown
                                                                 eUICC
                                                                Error during the creation of the key set at the ISD-R level. In that
8.4        ISD-R               4.2          Execution error     case, the output data “euiccResponseData contains the exact
                                                                response coming from the eUICC.
                                                            Error during the configuration of ISD-R by SM-SR2, after creating
                                            Stopped      on SM-SR2 keyset. This Status Code SHALL only be used when the
8.4        ISD-R               4.3               Warning
                                                            Function Execution Status’ is “Executed_WithWarning”
            eUICC
            Certificate                      Certificate
8.5.2                           6.3                              ECASD Certificate expired
            Authority                        Expired
            Certificate
8.5.1          ECASD               6.1          Verification Failed The verification of the receipt by SM -SR2 failed. SM-SR2 sends the
               Certification                                        failure message to SM-SR1.
               Request

Table 207: Handover eUICC Specific Status Codes

5.6.3 Authenticate SM-SR

Function name: AuthenticateSMSR

Related Procedures: SM-SR Change

Function group: eUICC Management

Function Provider: SM-SR

Description: This function is used to authenticate the new SM-SR to the eUICC identified by the EID. The function will return the random challenge generated by the eUICC to be used to create the signature for the second step in the SM-SR key establishment procedure.

This function may return:

    A ‘Function execution status’ with ‘Executed- Success’ indicating that the
     AuthenticateSMSR function has been successfully executed by the SM-SR as
     requested by the function caller.
    A ‘Function execution status’ with ‘Expired’ with a status code as defined in section
     5.1.6.4
    A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
     section 5.1.6.4 or a specific status code as defined in the table below.

Additional input data:

Input data name                   Description                     Type    No. MOC
                  Identification of the targeted eUICC.
eid                                                               EID     1   M
                  See section 5.1.1.1 for type description.

SM-SR Certificate.

                  The format of this field is a byte array which
smsrCertificate   content corresponds to the full content of tag Byte[]   1   M
                  '7F21' (including the two '7F21' bytes)
                  defined in Table 39

Table 208: Authenticate SM-SR Additional Input Data

Additional output data:

Output data name       Description       Type     No. MOC
                     The random
randomChallenge                         Byte[]    1    M
                     challenge

Table 209: Authenticate SM-SR Additional Output Data

NOTE:To avoid subliminal channel attacks, in case the execution Status is Failed or Expired, the SM-SR SHOULD return an empty hexadecimal strings as Random Challenge.

Specific status codes

Subj ect                        Reason
                    Subj ect                 Reason                                 Description
  code                           code
8.1.1               EID              1.1       Unknown            Indicates that the EID, is unknown to the function provider
                                                                  Error during the creation of the Random Challenge at the
8.4                 ISD-R            4.2       Execution error
                                                                  ISD-R level
                    SM-SR                      Certificate
8.7.1                                6.3                          SM-SR certificate expired
                    Certificate                Expired
                    SM-SR
8.7.1                                6.1       Verification failed SM-SR certificate signature cannot be verified
                    Certificate

Table 210: Authenticate SM-SR Specific Status Codes

Table 211: Void

5.7 ES4A (Operator – SM-SR) Interface Description

5.7.1 Setting M2M -SP Authorisations to Access Profiles

Function name: SetPLMA

Related Procedures: Set Profile Lifecycle Management Authorisations

Function group: Profile Management

Function Provider: SM-SR

Description:

This function allows the Operator owner of Profiles to grant a PLMA to an M2M SP to perform certain operations, or receive certain notifications, related to a certain subset of the Profiles owned by the Operator.

The SM-SR receiving this request SHALL verify that the mno-id in the PLMA matches the mno-id of the Operator who sends this request.

If the request is acceptable, the SM-SR SHALL record the PLMA.

The new PLMA overwrites the previous PLMA that might have been granted with the same identifiers.

From this point on, any request from the M2M SP on such a Profile, or any notification to the M2M SP related to such a Profile, SHALL be allowed or not based on the new PLMA, as described in sections 5.7.1.1 to 5.7.1.3.

This function may return:

       A ‘Function execution status’ with ‘Executed- Success’ indicating that the
        authorisations have been configured in the SM-SR.
       A ‘Function execution status’ with ‘Executed-WithWarning’ with a specific status code
        as defined in the table here after, indicating that the authorisations have been
        configured in the SM-SR but that some side-effects of this configuration may require
        the attention of the Operator.
       A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
        section 5.1.6.4 or a specific status code as defined in the table here after.

Additional input data:

Input data name                                     Description                                    Type     No.    MOC
plma                 The specification of the PLMA, and the criteria on which this PLMA applies.   PLMA      1      M
                     See section 5.1.1.2.14 for type description.

Table 571-A: Set PLMA Additional Input Data

Additional output data:

       None

Specific status codes

Subj ect               Reason
            Subj ect                Reason                                       Description
 code                  code
                                                  Indicates that the M2M SP to grant authorisations to is unknown to or not
  8.9       M2M SP      1.1     Unknown
                                                  connected to this SM-SR
                                                 Indicates that the Profile Type in the PLMA doesn’t match the Profile Type
                                                 of any Profile owned by the Operator identified by its mno -id.
           Profile
8.2.5                  4.9     Unassigned        The SM-SR MAY support this Status Code. If it does support it, the SM -SR
           Type
                                                 SHALL record the PLMA anyway, and the Execution Status SHALL be
                                                 Executed-WithWarning
                                                 Indicates that the new PLMA has overwritten a former PLMA on the same
                               Related
8.2.7      PLMA        3.6                       set of Profile/eUICC for the same M2M SP. In this case the Execution Status
                               Objects Exists
                                                 SHALL be Executed-WithWarning
                                                Indicates that the Operator, addressed by the mno -id in the PLMA, is
8.10      Operator    1.1     Unknown           unknown.

Table 571-B: SetPLMA Specific Status Codes

5.7.1.1 Matching of PLMAs Criteria When Receiving ES4 Requests

When an SM-SR receives a request on ES4 interface (where the client is an Operator or an M2M SP) to perform a Profile Lifecycle Management command targeting a certain Profile, it

SHALL verify that the function requester is authorised to perform that operation on that Profile. The verification SHALL include:

      If the ES4 function requester is the Operator owner of the Profile, the authorisation is
       granted
      If the ES4 function requester is an M2M -SP (including, if the requester is an Operator
       that is not the owner of the targeted Profile), the SM-SR SHALL:
   Check that the requested operation is eligible to PLMAs (e.g. updatePolicyRules
    is not eligible to such an authorisation)
   Check that there exists a PLMA, that includes:
   An m2m-sp-id that matches the identifier of the requesting M2M -SP.
   An mno-id that matches the targeted Profile’s mno-id
   A profileType that matches the targeted Profile’s ProfileType, or, if the targeted
    Profile’s Profile Type is missing, an empty profileType
   An authorisedOperation that matches the Profile Lifecycle Management
    command name, as listed in section 5.5.16.1.
NOTE             Even passing these checks doesn’t mean that the request will be accepted
                 and executed, as the SM-SR also performs other checks (e.g. POL2).
NOTE             The Profile Type of the targeted Profile can be found in the EIS of the eUICC
                 where this Profile is installed

5.7.1.2 Matching of PLMAs Criteria When Receiving ES3 Requests

When an SM-SR receives a request on ES3 interface (where the client is an SM-DP acting on behalf of an Operator) to perform a Profile Lifecycle Management command targeting a certain Profile, it SHALL verify that the function requester is authorised to perform that operation on that Profile. The verification SHALL include:

      The SM-SR SHALL extract the identity of the Operator that initiated the request to the
       SM-DP (ES2 requester)
      If this ES2 requester is the Operator owning the target Profile, the authorisation is
       granted
      If this ES2 requester is an Operator that is not the owner of the targeted Profile, the
       SM-SR SHALL
   Check that the requested operation is eligible to PLMAs (e.g. updatePolicyRules
    is not eligible to such an authorisation)
   Check that there exists a PLMA, that includes:
   An m2m-sp-id that matches the identifier of the ES2 requester.
   An mno-id that matches the targeted Profile’s mno-id
   A profileType that matches the targeted Profile’s profileType, or, if the targeted
    Profile’s profileType is missing, an empty profileType
   An authorisedOperation that matches the Profile Lifecycle Management
    command name, as listed in section 5.5.16.1
NOTE              Even passing these checks doesn’t mean that the request will be accepted
                  and executed, as the SM-SR also performs other checks (e.g. POL2).
NOTE              The Profile Type of the targeted Profile can be found in the EIS of the eUICC
                  where this Profile is installed

5.7.1.3 Matching of PLMA Criteria Before Sending Notifications

Similarly, after executing an operation that affects a Profile, the SM-SR SHALL verify if a notification recipient is authorised to receive notifications indicating Profile state changes. The verification SHALL include:

      If the notification recipient is the Operator owner of the Profile, the authorisation is
       granted
      If the notification recipient is an M2M SP (including, if the notification recipient is an
       Operator that is not the owner of the targeted Profile), the SM-SR SHALL:
    Check that the requested notification is eligible to PLMA
    Check that there exists a PLMA, that includes:
   An m2m-sp-id that matches the identifier of the M2M SP.
   An mno-id that matches the targeted Profile’s mno-id.
   A profileType that matches the targeted Profile’s profileType, or, if the targeted
    Profile’s Profile Type is missing, an empty profileType.
   An authorisedOperation that matches the notification name, as listed in section
    5.5.16.1.
NOTE              Even passing these checks doesn’t mean that the notification will be sent, as
                  the SM-SR also performs other checks (e.g. check that the Operator has not
                  set an ONC to discard this notifications).
NOTE              The Profile Type of the targeted Profile can be found in the EIS of the eUICC
                  where this Profile is installed.

5.7.2 Retrieving M2M SP Authorisations to Access Profiles

Function name: GetPLMA

Related Procedures: Retrieve Profile Lifecycle Management Authorisation by Operator

Function group: Profile Management

Function Provider: SM-SR

Description:

This function allows the Operator owner of Profiles to retrieve the list of PLMA applicable to a certain Profile, or a certain Profile type, or for a certain M2M SP.

The SM-SR receiving this request SHALL verify that the requester is the owner of the targeted Profile(s), and return the list of all PLMAs applicable to the specified search criteria.

In case the list of PLMAs is very long, the SM-SR MAY truncate the result. The caller can then issue another call to getPLMA with more restrictive criteria.

NOTE                 The order of the PLMAs returned in the list is implementation-dependant.

This function may return:

       A ‘Function execution status’ with ‘Executed- Success’, and additional output data
        providing the PLMAs.
       A ‘Function execution status’ with ‘Executed-WIthWarning’, to indicate that the result
        was truncated, plus additional output data providing part of the list of applicable
        PLMAs.

Additional input data:

Input data name                                           Description                                       Type     No.    MOC
profileType             Identification of the Profile type for which PLMAs are searched
                                                                                                            String     1       C
                        Identification of the M2M SP for which PLMAs are searched
m2m-sp-id                                                                                                     OID      1       C
iccid                   Identification of one specific Profile
                                                                                                            ICCID      1       C
                        Identification of the Operator owning the Profiles to be matched (this input
mno-id                                                                                                        OID      1       C
                        datum SHALL be present only in case the search criterion is a Profile Type).

See section 5.1.1.1 for type description.

Table 572-A: retrievePLMA Additional Input Data

One and only one of the input data profileType, m2m-sp-id and iccid SHALL be present.

Additional output data:

Output data name                         Description                       Type     No. MOC
                      The list of PLMA that match the search criterion
plma                  See section 5.1.1.2.14 for type description.         PLMA      N     M

Table 572-B: retrievePLMA Additional Output Data

Specific status codes

Subj ect                  Reason
             Subj ect                     Reason                                         Description
 code                      code
                                                           Indicates that the Operator or M2M SP which called this function is not
            Function                 Not Allowed           doesn’t have a PLMA granted that applies to the targeted Profile or
  1.1                       1.2
            requester                (Authorisation)       Profile type (including, if the targeted Profile or Profile type is unknown
                                                           to this SM-SR)
                                                         Indicates that the M2M SP specified in the search criterion is unknown
8.9       M2M SP          1.1      Unknown               to this SM-SR
                                         Indicates that the Operator, addressed by the mno -id in the PLMA is
8.10    Operator    1.1   Unknown        unknown.

Table 572-C: getPLMA Specific Status Codes

5.7.3 Setting Operator Configuration to Receive Notifications

Function name: SetONC

Related Procedures: Set Operator Notifications Configuration

Function group: Profile Management

Function Provider: SM-SR

Description:

This function allows the Operator to configure for which of its own Profiles, associated with a Profile Type, it wants to receive which kind of status change notifications; whatever the origin of the status change is.

The SM-SR receiving this request SHALL verify that the mno-id of the function caller matches with the one in the ONC.

If the request is acceptable, the SM-SR SHALL record the ONC. The new ONC overwrites the previous ONC that might have been granted with the same identifiers.

From this point on, any status change notification, irrespective of the cause and related to a Profile matching these identifiers, SHALL be sent or not based on the new ONC.

This function may return:

     A ‘Function execution status’ with ‘Executed-Success’ indicating that the notifications
      have been configured in the SM-SR.
     A ‘Function execution status’ with ‘Executed-WithWarning’ with a specific status code
      as defined in the table here after, indicating that the notifications have been
      configured in the SM-SR but that some side-effects of this configuration may require
      the attention of the Operator.
     A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
      section 5.1.6.4 or a specific status code as defined in the table here after.

NOTE: If no Operator Notification Configuration has yet been set in the SM-SR for a given Profile Type, then the Operator will receive all notifications for status changes for its own Profiles, associated with this Profile Type, see also section 3.21 for details.

Additional input data:

Input data name                                     Description                                    Type     No.   MOC
onc                  The specification of the ONC, and the criterion on which this ONC applies.
                                                                                                   ONC       1      M
                     See section 5.1.1.2.15 for type description.

Table 573-A: SetONC Additional Input Data

Additional output data:

       None

Specific status codes

Subj ect               Reason
            Subj ect                 Reason                                         Description
 code                  code
                                                      Indicates that the Profile Type in the ONC doesn’t match the Profile Type
                                                      of any Profile owned by the Operator identified by its mno -id.
           Profile
 8.2.5                  4.9     Unassigned            The SM-SR MAY support this Status Code. If it does support it, the SM-
           Type
                                                      SR SHALL record the ONC anyway, and the Execution Status SHALL
                                                      be Executed-WithWarning
                                                     Indicates that the new ONC has overwritten a former ONC on the same
                               Related     Objects
8.2.8     ONC          3.6                           identifiers. In this case the Execution Status SHALL be Executed-
                               Exists
                                                     WithWarning
                                                    Indicates that the Operator, addressed by the mno -id in the ONC, is
8.10     Operator     1.1     Unknown               unknown.
                              Not        Allowed Indicates that the requesting SM-DP is not allowed to configure ONCs
8.10     Operator     1.2
                              (Authorisation)    for the Operator, addressed by the mno-id in the ONC.

Table 573-B: SetONC Specific Status Codes

5.7.4 Retrieving Operator Notification Configuration

Function name: GetONC

Related Procedures: Retrieve Operator Notifications Configuration

Function group: Profile Management

Function Provider: SM-SR

Description:

This function allows the Operator to retrieve a list of status change notifications it does not want to receive for its own Profiles, associated with a Profile Type.

The SM-SR receiving this request SHALL verify that the mno-id of the function caller matches with the one in the ONC.

If the request is acceptable, the SM-SR SHALLreturn the ONC including the list of requested notifications applicable to the specified search criterion.

This function may return:

      A ‘Function execution status’ with ‘Executed-Success’, and additional output data
       providing the configured ONC.
      A ‘Function execution status’ with ‘Executed-WithWarning’ with a specific status code
       as defined in the table below, indicating that the notifications have been configured in
       the SM-SR but that some side-effects of this configuration may require the attention
       of the Operator, and additional output data providing the configured ONC.
      A ‘Function execution status’ indicating ‘Failed’ with a status code as defined in
       section 5.1.6.4 or a specific status code as defined in the table here after.

Additional input data:

Input data name                                         Description                                     Type     No.       MOC
profileType           Identification of the Profile Type for which the ONC is searched
                                                                                                        String   1         C
                      Identification of one specific Profile for which the ONC is searched
iccid                                                                                                   ICCID    1         C

Table 574-A: GetONC Additional Input Data

One and only one of the input data profileType and iccid SHALL be present.

Additional output data:

Output data
                                                     Description                                           Type          No. MOC
  name
               The ONC including the list of discarded notifications that match the search criterion
               See section 5.1.1.2.15 for type description.
               NOTE:
onc            If no Operator Notification Configuration has yet been set in the SM -SR for a given       ONC           N       M
               Profile Type, then the output data of this function will list no notification names, as
               all notifications will be sent for Profiles assigned with this Profile Type. See also
               section 3.21.3 and table 511215-A for details.

Table 574-B: GetONC Additional Output Data

A Mapping of Functions into Messages (Normative)

This Annex provides the mapping of the functions defined in section 5 into messages to be exchanged between the Roles.

Any technology can be used to transport those messages (mail, file, Web Services…) as soon as it is agreed between the sender and the receiver.

However, for interoperability purpose, Annex B of this specification specifies the particular binding to the Web Service technology, following the OASIS and W3C WS-* standard.

All along this Annex we can indifferently use either “function caller” or “sender entity” wording to designate the entity that has issued the function execution request. It is also the case regarding “function provider” and “receiver entity” to designate the entity that executes the function.

A.1 Namespaces and Schema References

In the context of this specification, a specific set of namespaces is used:

 rpsX: http://namespaces.gsma.org/esim-messaging/X The “X” at the end of the URI indicates the major version (for example 3 or 4) of this specification.

Note:        For backward-compatibility with former versions, version 4 of this
             specification uses constructs in namespace “/4” but also continues to use
             constructs defined in the “/3” namespace for operations and types that
             already existed in v3.

The XML schema defined in this specification refers to the following namespaces:

   xs: Extensible Markup Language (XML) 1.0, W3C Recommendation as defined in
    [47].
   ds: XML Signature Syntax and Processing (Second Edition), W3C Recommendation
    as defined in [48].

A.2 Message: <rps3:RPSMessage>

A message in the context of GSMA Embedded UICC Remote Provisioning and Management is composed of a mandatory header and a mandatory body. RPS message types are located in euicc.root.xsd file

XML Type                 Description
rps3:RPSMessage          Root element of any GSMA Embedded SIM Remote Provisioning and
                         Subscription Management message. Any RPS message is composed
                         of a mandatory header and a mandatory body.
rps3:RPSHeader          Header of the message. Contains mainly information for the transport
                        of the message.
rps3:RPSBody            Contains the core of the message. In the context of this specification, it
                        SHALL be composed of one single element defined within one of the
                        interfaces ES1, ES2, ES3, ES4 and ES7.

Table A2: RPS message types

A.2.1 Void

A.2.2 Void

A.3 Common Types

A.3.1 Common Message Types

Common request types are located in euicc.common.request.xsd file.

XML Type                     Description
rps3:BaseRequestType         The base type for a Request types. All requests extend this type.
rps3:BaseResponseType        The base type for a Response types. All responses extend this
                             type.
rps3:BaseNotificationType The base type for a Notification types. All notifications extend this
                          type.

Table A31: Common Message Types

A.3.2 Void

A.3.3 Void

A.3.4 Simple Types Mapping

Common simple types are located in euicc.common.types.xsd file.

Type           XML Type                        Description
AID            rps3:AIDType                    The AID (Application IDentifier) type defined in
                                               section 5.1.1.1 SHALL be mapped to the
                                               <rps3:AIDType>. The type is defined as a
                                               hexadecimal string representation of 5 to 16
                                               bytes.
Datetime       xs:dateTime                     The Datetime type defined in section 5.1.1.1
                                               SHALL be mapped to the simple built-in XML
                                               time <xs:datetime>.
EID            rps3:EIDType                    The EID (eUICC IDentifier) type defined in
                                               section 5.1.1.1 SHALL be mapped to the
                                               <rps3:EIDType>. The type is defined as a
                                               hexadecimal string representation of 16 bytes.
ICCID          rps3:ICCIDType                  The ICCID (Integrated Circuit Card IDentifier)
                                               type defined in section 5.1.1.1 SHALL be
                                               mapped to the <rps3:ICCIDType>. The type is
                                               defined as a string representation (up to 20
                                               digits), non-swapped as per ITU E.118
                                               representation. Example: 893301000000000011
MSISDN         rps3:MSISDNType                 The MSIDN (Mobile Station ISDN Number) type
                                               defined in section 5.1.1.1 SHALL be mapped to
                                               the <rps3:MSISDNType>. The type is defined
                                               as a string representation of up to 15 decimal
                                               digits as defined in ITU E.164, including Country
                                               code, National Destination Code (optional) and
                                               Subscriber Number. Example: 380561234567
IMSI           rps3:IMSIType                   The IMSI (International Mobile Subscriber
                                               Identity) type defined in section 5.1.1.1 SHALL
                                               be mapped to the <rps3:IMSIType>. The type is
                                               defined as a string representation of up to 15
                                               decimal digits including MCC (3 digits) and MNC
                                               (2 or 3 digits), as defined in ITU E.212.
                                               Example: 242011234567890
OID            rps3:ObjectIdentifierType       The OID (Object Identifier) type defined in
                                               section 5.1.1.1 SHALL be mapped to the
                                               <rps3:ObjectIdentifierType>. The type is defined
                                               as a string representation of an OID, i.e. of
                                               integers separated with dots (for example: '1.2',
                                               '3.4.5').
TAR            rps3:TARType                    The TAR (Toolkit Application reference) type
                                               defined in section 5.1.1.1 SHALL be mapped to
the <rps3:TARType>. The type is defined as a
hexadecimal string representation of exactly 3
bytes.         Example: 363443.
Version        rps3:ThreeDigitVersion          The Version type defined in section 5.1.1.1
                                               SHALL be mapped to the <rps3:
                                               ThreeDigitVersion>. The type is defined as a
                                               string representation of exactly 3 integers
                                               separated by a '.'. Example: 1.15.9

Table A34: Common Simple Types

A.3.4.1 Void

A.3.4.2 Void

A.3.4.3 Void

A.3.4.4 Void

A.3.4.5 Void

A.3.4.6 Void

A.3.4.7 Void

A.3.4.8 Void

A.3.4.9 Void

A.3.5 Complex Type Mapping

Common complex types already defined in version 3 of this specification are located in euicc.common.types.xsd file.

Type           XML Type                         Description
EIS            rps3:EISType                     The EIS type defined in section 5.1.1.2.13
                                                SHALL be mapped to the <rps3: EISType>.
                                                This type contains the whole information
                                                defined for EIS, but depending on the function
                                                where it is used, it may be filled with only a
                                                partial content.
All information requiring to be signed by the
EUM at registration time is regrouped under
the element <rps3:EumSignedInfo>. The
signature is provided within the <ds:Signature>
element (see section A.10 of this Annex).
Additional     rps3:AdditionalProperties        The <rps3:AdditionalProperties> allows a
Properties                                      neutral representation of any data based on a
                                                "Key:Value pair" representation. Such
                                                representation can be used without breaking
                                                the XML validation process.
Eum Signed rps3:EumSignedInfo                   The <rps3:EumSignedInfo> element contains
Info                                            all data included in the signature performed by
                                                the EUM.

All other data of the EIS are not signed.

Profile Info   rps3:ProfileInfo                 The <rps3:ProfileInfo> element contains the
                                                description of one Profile loaded on the eUICC
                                                (the <rps3:Eis> may contain several Profile
                                                <rps3:ProfileInfo>). The <rps3:ProfileInfo>
                                                maps the PROFILE INFO type defined in
                                                section 5.1.1.2.4.
Security       rps3:SecurityDomainType          The <rps3:SecurityDomainType> provides
Domain                                          description of a Security Domain and maps the
                                                SECURITY-DOMAIN type defined in section
                                                5.1.1.2.9. It is used to contain the information
                                                of the ISD-R and ECASD.
Key Set        rps3:KeySet                      The <rps3:Keyset> element contains the
                                                description of a key set and maps the KEYSET
                                                type defined in section 5.1.1.2.8.
Key Type       rps3:KeyType                     The <rps3:KeyType> contains the description
                                                of a key and maps the KEY type defined in
                                                section 5.1.1.2.6.
Key            rps3:KeyComponent                The <rps3:KeyComponent> element contains
Component                                       the description of a key component and maps
                                                the KEY-COMPONENT type defined in section
                                                5.1.1.2.5.
GP             rps3:GPCertificateType           The <rps3:GPCertificateType> contains the
Certificate                                     description of a key and maps the
                                                CERTIFICATE type. defined in section
                                                5.1.1.2.7.
Audit Trail    rps3:AuditTrail                  History of all the platform and Profile
                                                Management operations or eUICC notifications
                                                related to the eUICC. It contains list of Audit
                                                Trail Records.
Audit Trail      rps3:AuditTrailRecord          Single record contains eUICC audit
Record                                          information. Defined in section 5.1.1.2.11.
eUICC            rps3:EuiccCapablities          The <rps3:EuiccCapabilities> element maps
Capabilities                                    the EUICC-CAPABILITIES data type defined in
                                                section 5.1.1.2.10.
POL2             rps3:POL2Type                  List of POL2 rules.
POL2 Rule        rps3:POL2RuleType              The <rps3:POL2Type> maps the POL2 data
                                                type defined in section 5.1.1.2.3.
Subscription rps3:SubscriptionAddressType The <rps3:SubscriptionAddressType> maps
Address                                   the SUBSCRIPTION-ADDRESS data type
                                          defined in section 5.1.1.2.1.

Table A35: Common Complex Types

Common complex types introduced in version 4 of this specification are located in rps4.euicc.common.types.xsd file.

Type             XML Type                      Description
PLMA             rps4:PLMAtype                 The PLMA type defined in section 5.1.1.2.14
                                               SHALL be mapped to the <rps4:PLMAType>.
ONC              rps4:ONCtype                  The ONC type defined in section 5.1.1.2.15
                                               SHALL be mapped to the <rps4:ONCType>.

A.3.5.1 Void

A.3.5.2 Void

A.3.5.3 EUM Signature

Description moved to section A.10

A.3.5.4 Void

A.3.5.5 Void

A.3.5.6 Void

A.3.5.7 Void

A.3.5.8 Void

A.3.5.9 Void

A.4 The ES1 Interface Functions

The table below describe where definition of ES1 functions messages are located in euicc.request.ES1.xsd and rps4.euicc.request.ES1.xsd.

Interface.Function                       XML Type
ES1.RegisterEIS                          rps3:ES1-RegisterEISRequest

rps3:ES1RegisterEISResponse

ES1.UpdateEISAdditionalProperties        rps4: ES1-UpdateEISAdditionalPropertiesRequest

rps4: ES1-UpdateEISAdditionalPropertiesResponse

Table A4: ES1 Interface Functions

A.4.1 Void

A.5 The ES2 Interface Functions

The table below describe where definition of ES2 functions messages are located in rps3.euicc.request.ES2.xsd and rps4.euicc.request.ES2.xsd.

Interface.Function                       XML Type
ES2.GetEIS                               rps3:ES2-GetEISRequest

rps3:ES2-GetEISResponse

ES2.DownloadProfile                      rps3:ES2-DownloadProfileRequest

rps3:ES2-DownloadProfileResponse

ES2.UpdatePolicyRules                    rps3:ES2-UpdatePolicyRulesRequest

rps3:ES2-UpdatePolicyRulesResponse

ES2.UpdateSubscriptionAddress            rps3:ES2-UpdateSubscriptionAddressRequest

rps3:ES2-UpdateSubscriptionAddressResponse

ES2.EnableProfile                        rps3:ES2-EnableProfileRequest

rps3:ES2-EnableProfileResponse

ES2.DisableProfile                       rps3:ES2-DisableProfileRequest

rps3:ES2-DisableProfileResponse

ES2.DeleteProfile                        rps3:ES2-DeleteProfileRequest

rps3:ES2-DeleteProfileResponse

ES2.HandleProfileDisabledNotification rps3:ES2-HandleProfileDisabledNotification

ES2.HandleProfileEnabledNotification     rps3:ES2-HandleProfileEnabledNotification
ES2.HandleSMSRChangeNotification         rps3:ES2-HandleSMSRChangeNotification
ES2.HandleProfileDeletedNotification     rps3:ES2-HandleProfileDeletedNotification
ES2.AuditEis                             rps3:ES2-AuditEISRequest

rps3:ES2-AuditEISResponse

ES2.GetONC                               rps4:ES2-GetONCRequest

rps4:ES2-GetONCResponse

ES2.SetONC                               rps4:ES2-SetONCRequest

rps4:ES2-SetONCResponse

ES2.GetPLMA                              rps4:ES2-GetPLMARequest

rps4:ES2-GetPLMAResponse

ES2.SetPLMA                              rps4:ES2-SetPLMARequest

rps4:ES2-SetPLMAResponse

ES2.HandleProfileDownloadedNotific       rps4:ES2-HandleProfileDownloadedNotification
ation
ES2.HandlePLMAChangedNotificatio         rps4:ES2-HandlePLMAChangedNotification
n
ES2.HandlePolicyRulesUpdatedNotifi       rps4:ES2-HandlePolicyRulesUpdatedNotification
cation
ES2.SetFallBackAttribute                 rps4:ES2-SetFallBackAttributeRequest

rps4:ES2-SetFallBackAttributeResponse

ES2.SetEmergencyProfileAttribute         rps4:ES2-SetEmergencyProfileAttributeRequest

rps4:ES2-SetEmergencyProfileAttributeResponse

ES2.HandleEmergencyProfileAttribute rps4:ES2-
SetNotification                     HandleEmergencyProfileAttributeSetNotification
ES2.HandleEmergencyProfileAttribute rps4:ES2-
UnsetNotification                   HandleEmergencyProfileAttributeUnsetNotification
ES2.HandleProfileFallBackAttributeSe rps4:ES2-
tNotification                        HandleProfileFallBackAttributeSetNotification
ES2.HandleProfileFallBackAttributeUn rps4:ES2-
setNotification                      HandleProfileFallBackAttributeUnsetNotification

Table A5: ES2 Interface Functions

A.5.1 To A.5.12 Void

Descriptions moved to table and files referenced by section A.5

A.6 The ES3 Interface Functions

The table below describe where definition of ES3 functions messages are located in rps3.euicc.request.ES3.xsd and rps4.euicc.request.ES3.xsd.

Interface.Function                       XML Type
ES3.GetEIS                               rps3:ES3-GetEISRequest

rps3:ES3-GetEISResponse

ES3.AuditEIS                             rps3:ES3-AuditEISRequest

rps3:ES3-AudtiEISResponse

ES3.CreateISDP                           rps3:ES3-CreateISDPRequest

rps3: ES3-CreateISDPResponse

ES3.SendData                             rps3:ES3-SendDataRequest

rps3:ES3-SendDataResponse

ES3.ProfileDownloadCompleted             rps3:ES3-ProfileDownloadCompletedRequest

rps3:ES3-ProfileDownloadCompletedResponse

ES3.UpdatePolicyRules                    rps3:ES3-UpdatePolicyRulesRequest

rps3: ES3-UpdatePolicyRulesResponse

ES3.UpdateSubscriptionAddress            rps3:ES3-UpdateSubscriptionAddressRequest

rps3:ES3-UpdateSubscriptionAddressResponse

ES3.EnableProfile                        rps3:ES3-EnableProfileRequest

rps3:ES3-EnableProfileResponse

ES3.DisableProfile                       rps3:ES3-DisableProfileRequest

rps3:ES3-DisableProfileResponse

ES3.DeleteISDP                           rps3:ES3-DeleteISDPRequest

rps3:ES3-DeleteISDPResponse

ES3.UpdateConnectivityParameters         rps3:ES3- UpdateConnectivityParametersRequest

rps3:ES3- UpdateConnectivityParametersResponse

ES3.HandleProfileDisabledNotification rps3:ES3-HandleProfileDisabledNotification

ES3.HandleProfileEnabledNotification     rps3:ES3-HandleProfileEnabledNotification
ES3.HandleSMSRChangeNotification         rps3: ES3-HandleSMSRChangeNotification
ES3.HandleProfileDeletedNotification     rps3: ES3-HandleProfileDeletedNotification
ES3.GetONC                               rps4:ES3-GetONCRequest

rps4:ES3-GetONCResponse

ES3.SetONC                               rps4:ES3-SetONCRequest

rps4:ES3-SetONCResponse

ES3.GetPLMA                              rps4:ES3-GetPLMARequest

rps4:ES3-GetPLMAResponse

ES3.SetPLMA                              rps4:ES3-SetPLMARequest

rps4:ES3-SetPLMAResponse

ES3.HandleProfileDownloadedNotific       rps4:ES3-HandleProfileDownloadedNotification
ation
ES3.HandlePLMAChangedNotificatio         rps4:ES3-HandlePLMAChangedNotification
n
ES3.HandlePolicyRulesUpdatedNotifi       rps4:ES3-HandlePolicyRulesUpdatedNotification
cation
ES3.SetFallBackAttribute                 rps4:ES3-SetFallBackAttributeRequest

rps4:ES3-SetFallBackAttributeResponse

ES3.SetEmergencyProfileAttribute         rps4:ES3-SetEmergencyProfileAttributeRequest

rps4:ES3-SetEmergencyProfileAttributeResponse

ES3.HandleEmergencyProfileAttribute rps4:ES3-
SetNotification                     HandleEmergencyProfileAttributeSetNotification
ES3.HandleEmergencyProfileAttribute rps4:ES3-
UnsetNotification                   HandleEmergencyProfileAttributeUnsetNotification
ES3.HandleProfileFallBackAttributeSe rps4:ES3-
tNotification                        HandleProfileFallBackAttributeSetNotification
ES3.HandleProfileFallBackAttributeUn rps4:ES3-
setNotification                      HandleProfileFallBackAttributeUnsetNotification

Table A6: ES3 Interface functions

A.6.1 to A.615 Void

Descriptions moved to table and files referenced by section A.6

A.7 The ES4 Interface Functions

The table below describe where definition of ES4 functions messages are located in rps3.euicc.request.ES4.xsd and rps4.euicc.request.ES4.xsd.

Interface.Function                       XML Type
ES4.GetEIS                               rps3:ES4-GetEISRequest

rps3:ES4-GetEISResponse

ES4.UpdatePolicyRules                    rps3:ES4-UpdatePolicyRulesRequest

rps3:ES4-UpdatePolicyRulesResponse

ES4.UpdateSubscriptionAddress            rps3:ES4-UpdateSubscriptionAddressRequest

rps3:ES4-UpdateSubscriptionAddressResponse

ES4.AuditEIS                             rps3:ES4-AuditEISRequest

rps3:ES4-AuditEISResponse

ES4.EnableProfile                        rps3:ES4-EnableProfileRequest

rps3:ES4-EnableProfileResponse

ES4.DisableProfile                       rps3:ES4-DisableProfileRequest

rps3:ES4-DisableProfileResponse

ES4.DeleteProfile                        rps3:ES4-DeleteProfileRequest

rps3:ES4-DeleteProfileResponse

ES4.PrepareSMSRChange                    rps3:ES4-PrepareSMSRChangeRequest

rps3:ES4-PrepareSMSRChangeResponse

ES4.SMSRChange                           rps3:ES4-SMSRChangeRequest

rps3:ES4-SMSRChangeResponse

ES4.HandleProfileDisabledNotification rps3:ES4-HandleProfileDisabledNotification

ES4.HandleProfileEnabledNotification     rps3:ES4-HandleProfileEnabledNotification
ES4.HandleSMSRChangeNotification         rps3:ES4-HandleSMSRChangeNotification
ES4.HandleProfileDeletedNotification     rps3:ES4-HandleProfileDeletedNotification
ES4.GetPLMA                              rps4:ES4-GetPLMARequest

rps4:ES4-GetPLMAResponse

ES4.HandleProfileDownloadedNotific       rps4:ES4-HandleProfileDownloadedNotification
ation
ES4.HandlePLMAChangedNotificatio         rps4:ES4-HandlePLMAChangedNotification
n
ES4.HandlePolicyRulesUpdatedNotifi       rps4:ES4-HandlePolicyRulesUpdatedNotification
cation
ES4.HandleEmergencyProfileAttribute rps4:ES4-
SetNotification                     HandleEmergencyProfileAttributeSetNotification
ES4.HandleEmergencyProfileAttribute rps4:ES4-
UnsetNotification                   HandleEmergencyProfileAttributeUnsetNotification
ES4.HandleProfileFallBackAttributeSe rps4:ES4-
tNotification                        HandleProfileFallBackAttributeSetNotification
ES4.HandleProfileFallBackAttributeUn rps4:ES4-
setNotification                      HandleProfileFallBackAttributeUnsetNotification

Table A7: ES4 Interface functions

A.7.1 to A.7.13 Void

Descriptions moved to table and files referenced by section 397A.7

A.8 The ES4A Interface Functions

The table below describes where definition of ES4A functions messages are located in rps4.euicc.request.ES4A.xsd.

Interface Function                       XML Type
ES4A.GetONC                              rps4:ES4A-GetONCRequest

rps4:ES4A-GetONCResponse

ES4A.SetONC                              rps4:ES4A-SetONCRequest

rps4:ES4A-SetONCResponse

ES4A.GetPLMA                             rps4:ES4A-GetPLMARequest

rps4:ES4A-GetPLMAResponse

ES4A.SetPLMA                             rps4:ES4A-SetPLMARequest

rps4:ES4A-SetPLMAResponse

Table A8: ES4A Interface Functions

A.9 The ES7 Interface Functions

The table below describes where the definition of ES7 functions messages are located in euicc.request.ES7.xsd.

Interface.Function          XML Type                                      XSD File
ES7.CreateAdditionalKe      rps3:ES7-CreateAdditionalKeySetRequest euicc.request.ES7.xsd
ySet
                            See Notes 1 and 2
rps3:ES7-
CreateAdditionalKeySetResponse
ES7.HandoverEUICC           rps3:ES7-HandoverEUICCRequest

rps3:ES7-HandoverEUICCResponse

ES7.AuthenticateSMSR         rps3:ES7-AuthenticateSMSRRequest

rps3:ES7-AuthenticateSMSRResponse

NOTE1         ES7.CreateAdditionalKeySet: Due to backward compatibility reasons, the
              XML Schema defining this element does not allow to omit the
              initialSequenceCounter element, nor to give it an empty value. However,
              whichever value set in this element by the calling SM-SR will be ignored by
              the SM-SR receiving this command (see NOTE 1 of section 5.6.1). The
              calling SM-SR SHOULD set a value that is clearly not relevant as an initial
              sequence counter value (e.g. -1)
NOTE 2        ES7.CreateAdditionalKeySet: Due to backward compatibility reasons, the
              XML Schema defining this element does not allow to omit the hostId
              element. However, the value set in this element by the calling SM-SR is
              irrelevant if the scenarioParameter does not specify to use a hostId (see
              NOTE 2 of section 5.6.1). In this case, the calling SM-SR SHOULD set an
              empty value (empty string).

A.9.1 to A.8.3 Void

Descriptions moved to table and files referenced by section 397A.9

A.10 EUM Signature

The EUM signature over some information of the EIS is provided within the <rps3:EumSignature> element of type <ds:SignatureType> as defined in XML Signature Syntax and Processing (Second Edition) [26].

The <rps3:EumSignature> SHALL include:

    A <ds:SignedInfo> element specifying:
      a <ds:CanonicalizationMethod> element;
        This specification mandates the support of the following method
        ‘http://www.w3.org/2001/10/xml-exc-c14n#’
   a <ds:SignatureMethod> element; this specification mandates usage of one of the
    following signature method to have a compliant level of security (RSA and EC key
    length following recommendation given in section 2.3.3)
    http://www.w3.org/2001/04/xmldsig-more#rsa-sha256
    http://www.w3.org/2001/04/xmldsig-more#rsa-sha384
    http://www.w3.org/2001/04/xmldsig-more#rsa-sha512
    http://www.w3.org/2001/04/xmldsig-more#ecdsa-sha256
     http://www.w3.org/2001/04/xmldsig-more#ecdsa-sha384
     http://www.w3.org/2001/04/xmldsig-more#ecdsa-sha512
    a unique <ds:Reference> element
      with no URI attribute as the signed info applies always only on the whole
         <rps3:EumSignedInfo> element (so no need to specify it in the instance
         document);
      with a digesting method as one of:
     http://www.w3.org/2001/04/xmlenc#sha256
     http://www.w3.org/2001/04/xmldsig-more#sha384
     http://www.w3.org/2001/04/xmlenc#sha512
      with a <ds:Transforms> transforms element containing one single
         <ds:Transform> element, to specify the canonicalization method for the
         reference
         o This specification mandates the support of the following method
             ‘http://www.w3.org/2001/10/xml-exc-c14n#’
    A <ds:KeyInfo> containing a reference to the certificate used to generate the
     signature. This is achieved by including a <ds:X509Data> element containing either:
      a <ds:X509SubjectName>, providing the subject value of a certificate that the
        receiving entity is supposed to have. In this case, it is the responsibility of the
        EUM to ensure that the Subject of its certificates are sufficiently distinctive to
        uniquely identify its certificates (for a given eum-id).
      Or a <ds:X509Certificate>, containing the full certificate definition (including the
        public key)
    <ds:SignatureValue> element providing the signature value applied on whole
     <ds:SignedInfo> element, as specified by the W3C, after application of the specified
     canonicalization, transform and digesting methods as specified within the
     <ds:SignedInfo> element.

Example of <ds:Signature>:

<EumSignature xmlns:ds="http://www.w3.org/2000/09/xmldsig#">
   <ds:SignedInfo>
       <ds:CanonicalizationMethod Algorithm=http://www.w3.org/2001/10/xml-exc-c14n#/>
       <ds:SignatureMethod Algorithm=http://www.w3.org/2001/04/xmldsig-more#rsa-sha256/>
       <ds:Reference>
            <ds:Transforms>
             <ds:Transform Algorithm="http://www.w3.org/2001/10/xml-exc-c14n#" />
         </ds:Transforms>
         <ds:DigestMethod Algorithm=http://www.w3.org/2001/04/xmlenc#sha256/>
         <ds:DigestValue>dHLkPm5pcyBub3QgYSBzaWduYXR1cmGB</ds:DigestValue>
    </ds:Reference>
</ds:SignedInfo>
<ds:SignatureValue>dHLkPm5pcyBub3QgYSBzaWduYXR1cmGB</ds:SignatureValue>
   <ds:KeyInfo>
       <ds:X509Data>
         <ds:X509SubjectName>CN=gsma, O=GSMA, C=UK</ds:X509SubjectName>
       </ds:X509Data>
   </ds:KeyInfo>
</ds:Signature>

B Binding to SOA Environment (Normative)

This section provides the binding of the messages defined in Annex A into a SOA infrastructure.

Web Services technology, following the OASIS and W3C WS-* standard, is the SOA environment recommended for the deployment of the off-card entities interfaces specified in this document. This technology provides interoperability and loose coupling between the interface provider and the interface consumer, also named respectively as "message receiver" and "message sender", “or “function provider” and “function requeste r”.

However this specification does not prevent from using another type of technology if it is suitable for a specific deployment. For sure, it implies that both message sender and message receiver uses the same technology and security around matches the level of expectation expressed in this document.

Nevertheless, in case Web Services is used, this section is normative and implementation SHALL comply with the requirements provided in this section.

B.1 General Recommendations

Systems are now highly multi-threaded. It is consequently possible for a function caller to perform massive parallel processing, and thus to call several Web Services in parallel. However, to avoid implementation and integration issues, this specification mandates that Function requester SHALL NOT perform parallel Web Services calls when they are targeting the same eUICC.

Web Services related to the same eUICC SHALL be serialised by the Function requester. For example to avoid key establishment to happen before ISD-P is created. Procedures described in section 3 SHALL be strictly followed regarding the sequence call.

If several Web Service calls are received by the Function provider for the same eUICC, then the Function provider could either:

   Return the following exception: 'Function for the same eUICC is already in process'.
   Or accept the new function execution request, and queue it to be executed after the
    already accepted function execution requests for this eUICC. This can only be
    applicable to asynchronous request (see B.2.3.3).

B.2 SOAP Binding

This section provides normative rules defining how to map the GSMA Embedded UICC Remote Provisioning messages (called RPS messages in the rest of section) defined in Annex A to a Web Services implementation, the rules being conditioned by Message Exchange Patterns (MEP), see B.2.3).

This specification mandates usage of SOAP v1.2 as the minimal version and specified in [40].

This section makes use of the following namespaces:

    wsa: the namespace for WS-Addressing message elements as defined in [41]
    wsmc: the namespace for WS-MakeConnection elements as defined in [43]

B.2.1 Message Binding

A RPS message consists of a body and a header (see A.2). This concept maps very well to the concept of SOAP messages that also contains a header and a body.

The binding of the messages defined in Annex A to SOAP SHALL follow the rules defined in this section.

    SOAP Header
      The information contained in the RPSHeader of the message SHALL be transferred
       into the SOAP header. See also B.2.2.1
    SOAP Body
      Only the element contained in the RPSBody structure SHALL be sent into the
       SOAP Body. It means that:
       The RPSMessage envelope SHALL NOT be sent.
       The full RPSHeader structure SHALL NOT be sent.
       The RPSBody envelope SHALL NOT be sent
      The SOAP body SHALL contain the rps3:MessageVersion attribute filled with the
       value of the <rps3:RPSMessage>/<rps3:MessageVersion> attribute.
   The SOAP body SHALL use pre-defined namespaces prefixes for XML nodes
    which are used as signature material. Namespace to prefix mapping:
   ‘http://namespaces.gsma.org/esim-messaging/3’ SHALL be
    mapped to ‘rps3’.
   ‘http://www.w3.org/2000/09/xmldsig#’ SHALL be mapped to ‘ds’.

NOTE:the location of namespace declaration in XML affects the signature computation. The canonicalization method specified in A.3.5.3 ensures the consistent location of the namespace declaration before computation or verification of the signature.

As a consequence one RPS message corresponds to one SOAP message, and it is impossible to send several RPS messages in a single SOAP message.

Note that all information of the RPS message is bind to the SOAP message, so no information is lost during the binding.

<rps:RPSMessage>                                <soap:Envelop>
 <rps:RPSHeader>                                 <soap:Header >
         <rps:…/>
         …                                              …
         <rps:…/>
 </rps:RPSHeader>                                </soap:Header>
<rps:RPSBody>                                  <soap:Body>
       <rps:…>                                        <rps:…>
         </rps:…>                                        </rps:…>
 </rps:RPSBody>                                  </soap:Body>
</rps:RPSMessage>                               </soap:Envelop>

Figure 141: RPS Message Binding

B.2.1.1 RPS Header Binding to WS-Addressing Elements

This section describes the binding of RPS header into WS-Addressing properties. WS- Addressing properties are described in further detail in [41] and [42]. Only the elements that are used throughout this section are detailed here.

 /wsa:From This element is defined in WS-Addressing core specifications [41] as:

This OPTIONAL element (of type wsa:EndpointReferenceType) provides the value for the [source endpoint] property.

In the context of this specification this element is MANDATORY except in the synchronous response and defines the function requester. It SHALL be filled with:

   The sender URI. This value is not mapped from any value of the RPS Header, but
    it should be representative of the sender entity.
   A mandatory query parameter “EntityId” containing the
    <rps3:SenderEntity>/<rps3:EntityId> value. Identifies the direct
    function caller.
   An optional query parameter “EntityName” containing the
    <rps3:SenderEntity>/<rps3:EntityName> value. Names the direct
    function caller.
   An optional query parameter “UserName” containing the <rps3:SenderName>
   A mandatory query parameter "MnoId" only for ES3 request messages containing
    the <rps3:MnoId></rps3:MnoId> value, to identify the Operator which sent the
    request to the SM-DP via ES2.

Example:

The following content:
       <rps:SenderEntity>
               <rps:EntityId>1.3.6.1.4.1.11111</rps:EntityId>
               <rps:EntityName>ACompany</rps:EntityName>
       </rps:SenderEntity>
       <rps:SenderName>aSenderAccountId</rps:SenderName>
       <rps3:MnoId>1.3.5.6.1</rps3:MnoId>
Would be mapped into:

<wsa:From>

      <wsa:Address>http://ACompany.com/RPS?EntityId=1.3.6.1.4.1.11111?Entit
yName=ACompany?UserName=aSenderAccountId?MnoId=1.3.5.6.1</wsa:Address>
       </wsa:From>
    /wsa:To
This element is defined in WS-Addressing core specifications [41] as:

This REQUIRED element (of type xs:anyURI) provides the value for the [destination] property.

In the context of this specification this element is MANDATORY and defines the function provider. It SHALL be filled with:

   The URL of the web service endpoint to which the message is sent. This value is
    not mapped from any value of the RPS Header, but it should be representative of
    the receiving entity.
   An optional query parameter “EntityId” containing the
    <rps3:ReceiverEntity>/<rps3:EntityId> value
   A mandatory query parameter “MnoId” only for ES3 response and notification
    messages containing the <rps3:MnoId></rps3:MnoId> value, to identify the
    Operator to which the SM-DP SHALL send the response or notification via ES2.
    The parameter “MnoId” represents:
     Either the Operator which is owner of the Profile
     Or the Operator which is an M2M SP and has a PLMA set to receive this
       notification

Figure B211-A: MnoId Parameter on ES3 Interface

By mapping the “MnoID”, provided on ES3 interface, into the “EntityId” on the ES2 interface, the SM-DP or any interconnected routing entity can identify the Operator to which the response or notification SHALL be sent.

Example:

The following content:

       <rps3:ReceiverEntity>
               <rps3:EntityId>1.3.6.1.4.1.22222</rps3:EntityId>
       </rps3:ReceiverEntity>
Would be mapped into:
      <wsa:To>http://ACompany.com/SMDP/ES2Services?EntityId=1.3.6.1.4.1.222
22</wsa:To>

 /wsa:ReplyTo This element is defined in WS-Addressing core specifications [41] as:

This OPTIONAL element (of type wsa:EndpointReferenceType) provides the value for the [reply endpoint] property. If this element is NOT present, then the value of the [address] property of the [reply endpoint] EPR is "http://www.w3.org/2005/08/addressing/anonymous".

In the context of this specification this element is OPTIONAL. This element SHALL be present only when:

   MEP follows Asynchronous Request-Response with callback and
   When Message sender wants the response to be sent to a specific endpoint

If missing, the response SHALL be sent to (in the preferred order):

   a well-known endpoint mutually agreed between message sender and message
    receiver
   or to the message originating endpoint.

If present, the /wsa:ReplyTo SHALL be filled with:

   The value set in <rps3:ResponseEndpoint>
   An optional query parameter “EntityId” containing the
    <rps3:ReceiverEntity>/<rps3:EntityId> value

Example:

The following content:
      <rps3:ResponseEndpoint>http://ACompagny.com/SMDP/ES3Services</rps3:Re
sponseEndpoint>
       <rps3:ReceiverEntity>
               <rps3:EntityId>1.3.6.1.4.1.33333</rps3:EntityId>
       </rps3:ReceiverEntity>
Would be mapped into:
       <wsa:ReplyTo>
<wsa:Address>http://ACompany.com/SMDP/ES3Services?EntityId=1.3.6.1.4.1.3333
3</wsa:Address> </wsa:ReplyTo>

 /wsa:MessageID This element is defined in WS-Addressing core specifications [41] as:

This OPTIONAL element (whose content is of type xs:anyURI) conveys the [message id] property.

In the context of this specification this element is MANDATORY whatever the MEP. This element SHALL be filled with:

   The value set in <rps3:MessageId>.
   An optional query parameter “TransactionID” containing the
    <rps3:TransactionId> value. This query parameter SHALL be present only if
    <rps3:TransactionId> is present.
   An optional query parameter “ContextID” containing the <rps3:ContextId>
    value. If this optional query parameter is present, it SHALL be included in any new
    request generated by the function provider entity for another functional provider
    entity. This identifier MAY be used to provide end-to-end logging management
    between the different web services.
   A mandatory query parameter “MessageDate” containing the
    <rps3:MessageDate> value
   A mandatory query parameter "ProfileType" only for notifications messages
    containing the <rps3:ProfileType></rps3:ProfileType> value.

NOTE:This information allows the recipient to route the message based on "ProfileType".

Example:

The following content: <rps3:MessageId>//MySenderDomain/123</rps3:MessageId> <rps3:TransactionId>MyTansactionID1</rps3:TransactionId> <rps3:ContextId>MyContextID1</rps3:ContextId> <rps3:MessageDate>2013-04-18T09:45:00Z</rps3:MessageDate> <rps3:ProfileType>3G_16K</rps3:ProfileType>

Would be mapped into:
      <wsa:MessageID>//MySenderDomain/123?TransactionId=MyTansactionID1?Con
textId=MyContextID1?MessageDate=2013-04-18T09:45:00Z?ProfileType=3G_16K
</wsa:MessageID>

 /wsa:Action This element is defined in WS-Addressing core specifications [41] as:

This REQUIRED element (whose content is of type xs:anyURI) conveys the value of the [action] property.

In the context of this specification this element is MANDATORY, and the format of this element SHALL be:

       [target namespace] [delimiter][interface name] [delimiter][function
group][delimiter][operation name][direction token]

Where:

   [target namespace]: ‘http://gsma.com’
   [interface name]: One of the following label ‘ES1’, ‘ES2’ ‘ES3’, ‘ES4’ ‘ES7’,
   [function group]:
     For Synchronous Request-Response MEP, for Notification MEP, and for
        Asynchronous with Polling MEP, the [function group] value SHALL be filled with
        the name of the functions group (see Table 96 and Table 97). Possible values
        are:
        eUICCManagement
        ProfileManagement
          PlatformManagement
      For Asynchronous with callback MEP, the [function group] value SHALL be filled
          with the name of the functions group appended with the "CallBack" string.
          Possible values are:
          ProfileManagementCallBack
          PlatformManagementCallBack
          eUICCManagementCallBack
    [Operation name]: the name of the function as contained in the
     /rps3:RPSHeader/rps3:MessageType element
    [direction token] = Follows OASIS WS-* specifications, i.e.:
      For Synchronous Request-Response MEP: the [direction token] is already part of
          the [Operation Name] as the "Request" string for the request, and as the
          "Response" string for the response. So no additional qualifier SHALL be added.
      For Notification (One-Way MEP): no direction Token (empty string) needs to be
          added after the [Operation name]
      For Asynchronous with callback MEP or Asynchronous with Polling: as these
          MEP are indeed mapped to two one-way service calls, then there is no need to
          have a direction token, neither for the request, nor for the asynchronous response
          (empty strings). The ‘Resquest’ and ‘Response’ qualifier SHALL be removed from
          the [Operation name].
    [delimiter]: “/”
Examples:
      For the ES2 ‘GetEIS’ part of the ‘Profile Management’ function group, the relevant
       /wsa:Action SHALL be (assumed to be called as a Synchronous Request-Response
       MEP):
        For the request:
      <wsa:Action>http://gsma.com/ES2/ProfileManagement/ES2-
GetEISRequest</wsa:Action>
          For the response:
      <wsa:Action>http://gsma.com/ES2/ProfileManagement/ES2-
GetEISResponse</wsa:Action>
      For the ES3 ‘HandleProfileDisabledNotification’ part of the ‘Platform Management’
       function group, the relevant /wsa:Action SHALL be for the request (no response
       expected):
      <wsa:Action>http://gsma.com/ES3/PlatformManagement/ES3 -
HandleProfileDisabledNotification</wsa:Action>
      For the ES3 ‘EnableProfile’ part of the ‘Platform Management’ function group, the
       relevant /wsa:Action SHALL be (assumed to be called as a Asynchronous Request-
       Response with callback MEP):
        For the request:
      <wsa:Action>http://gsma.com/ES3/PlatformManagement/ES3 -
EnableProfile</wsa:Action>
          For the response:
      <wsa:Action>http://gsma.com/ES3/PlatformManagementCallBack/ES3 -
EnableProfile</wsa:Action>
      For the ES3 ‘EnableProfile’ part of the ‘Platform Management’ function group, the
       relevant /wsa:Action SHALL be (assumed to be called as a Asynchronous with
       Polling MEP):
        For the request:
      <wsa:Action>http://gsma.com/ES3/PlatformManagement/ES3 -
EnableProfile</wsa:Action>
          For the response:
      <wsa:Action>http://gsma.com/ES3/PlatformManagement/ES3 -
EnableProfile</wsa:Action>

 /wsa:FaultTo This element is defined in WS-Addressing core specifications [41] as:

This OPTIONAL element (of type wsa:EndpointReferenceType) provides the value for the [fault endpoint] property.

In the context of this specification this element SHALL NOT be used. Any fault SHALL be sent to (in the preferred order):

   The endpoint specified in the /wsa:ReplyTo, if present,
   Else, to a well know endpoint mutually agreed between message sender and
    message receiver
   Or to the message originating endpoint.

 /wsa:RelatesTo This element is defined in WS-Addressing core specifications [41] as:

This OPTIONAL (repeating) element information item contributes one abstract [relationship] property value, in the form of an (IRI, IRI) pair. The content of this element (of type xs:anyURI) conveys the [message id] of the related message.

In the context of this specification this element is MANDATORY if the message is an asynchronous response. This element SHALL be filled with the value of the <wsa:MessageID> of the related request.

Example:

The following content in SOAP request:

      <wsa:MessageID>//MySenderDomain/123?TransactionId=MyTansactionID1? Con
textId=MyContextID1?MessageDate=2013-04-18T09:45:00Z</wsa:MessageID>
triggers the following determination of <rps3:relatesTo>:

<rps:RelatesTo>//MySenderDomain/123</rps:RelatesTo>

The <wsa:RelatesTo> in the SOAP response SHALL be equal to the <wsa:MessageID> of the request:

      <wsa:RelatesTo>//MySenderDomain/123?TransactionId=MyTansactionID1
?ContextId=MyContextID1?MessageDate=2013-04-18T09:45:00Z </wsa:RelatesTo>

NOTE:There is no direct mapping from <rps3:RelatesTo> to <wsa:RelatesTo>. The <wsa:RelatesTo> SHALL be equal to <wsa:MessageId> from the request, while <rps3:RelatesTo> is only a subset of <wsa:RelatesTo>.

A function requester receiving a SOAP response from a function provider compliant with a version v3.2 or earlier of the current specification, SHOULD be ready to handle a <wsa:RelatesTo> value that is not equal to the value of the <wsa:MessageID> of the SOAP request. A function provider sending a SOAP response to a function requester compliant with a version v3.2 or earlier of the current specification, MAY return a <wsa:RelatesTo> value that is not equal to the value of the <wsa:MessageID> of the SOAP request.

NOTE:Versions v3.2 and earlier derived from WS-Addressing specification [41], and stated that the <wsa:RelatesTo> was equal to the <rps3:relatesTo>, and consequently, equal to the <rps3:messageId> of the corresponding request, but different from the <wsa:MessageID> of the corresponding request.

B.2.1.2 Use of WS-MakeConnection

WS-MakeConnection SHALL be used in asynchronous scenarios when the receiving party of a request cannot initiate a connection to the sending party (due to network security constraints for example). In this scenario, the sending party SHALL poll for a processed request using WS-MakeConnection [43]. This scenario is described in the Message Exchange Pattern: Asynchronous with Polling (Annex B-Section 2.3.3).

All the following elements are described in further detail in WS-MakeConnection [43], only the elements that are used throughout this document are detailed here.

To indicate to the Function provider that the Function requester is not addressable and will use Asynchronous with polling MEP (see B.2.3.3), the /wsa:ReplyTo header element SHALL indicate one of the two anonymous URL:

   The              WS-Addressing                              anonymous              URL
    ‘http://www.w3.org/2005/08/addressing/anonymous’. This SHALL allow the function
    requester to poll for the first response message available for the function requester
   The WS-MakeConnection anonymous URL                      ‘http://docs.oasis-open.org/ws-
    rx/wsmc/200702/anonymous?id=<value of <wsa:MessageId>’. This SHALL allow the
    Function requester to poll for the response for this specific message.

By using one of the two above anonymous /wsa:ReplyTo URL constructs, the Function provider knows that ‘Asynchronous with Polling’ mode is requested and SHALL answer with HTTP 202 (ACCEPT), see B.2.3.3.

To get a Function execution response, The Function provider SHALL send a new SOA P message with the /wsmc:MakeConnection element in the body; this new message establishes a contextualised back-channel for the transmission of the message response according to matching criteria (defined below).

In the context of this specification, the SOAP message allowing getting a function execution response message SHALL contain:

In the Header:

       /wsa:Action element with the specific value ‘http://docs.oasis-open.org/ws-
        rx/wsmc/200702/MakeConnection’
In the body:
   /wmc:MakeConnection element with a sub element /wsmc:Address containing one
    of the anonymous URI defined here above and identifying the initiating endpoint
    contained in the /wsa:ReplyTo element of the original function execution request.
    Function provider SHALL NOT return message response in the HTTP response unless
    they have been addressed to this URI.
     If the Function provider has not any response ready for the Function requester it
        SHALL answer with an empty response and HTTP 202 (ACCEPT)
     If the Function provider has a response ready it SHALL return the response and
        use HTTP response code 200 (OK)

B.2.1.3 RPS Body Binding and signature

At least the RPS Body elements which are used for signature computation or verification (for example rps3:EumSignedInfo and ds:SignedInfo) SHALL have whitespaces between XML nodes trimmed (i.e. remove leading and trailing whitespaces).

Example :

1)EUM Signature before trimming :

<EumSignature xmlns:ds="http://www.w3.org/2000/09/xmldsig#">
 <ds:SignedInfo>
   <ds:CanonicalizationMethod Algorithm=http://www.w3.org/2001/10/xml-exc-c14n#/>
   <ds:SignatureMethod Algorithm=http://www.w3.org/2001/04/xmldsig -more#rsa-
sha256/>
   <ds:Reference>
    <ds:Transforms>
     <ds:Transform Algorithm="http://www.w3.org/2001/10/xml-exc-c14n#"/>
    </ds:Transforms>
    <ds:DigestMethod Algorithm=http://www.w3.org/2001/04/xmlenc#sha256/>
    <ds:DigestValue>dHLkPm5pcyBub3QgYSBzaWduYXR1cmGB</ds:DigestValue>
   </ds:Reference>
 </ds:SignedInfo>
 <ds:SignatureValue>dHLkPm5pcyBub3QgYSBzaWduYXR1cmGB</ds:SignatureValue>
 <ds:KeyInfo>
   <ds:X509Data>
    <ds:X509SubjectName>CN=gsma, O=GSMA, C=UK</ds:X509SubjectName>
   </ds:X509Data>
 </ds:KeyInfo>
</ds:Signature>

2)EUM Signature after trimming (on one line):

<EumSignature xmlns:ds="http://www.w3.org/2000/09/xmldsig#"><ds:SignedInfo><ds:C anonicalizationMethod Algorithm=http://www.w3.org/2001/10/xml -exc-c14n#/><ds:Sig natureMethod Algorithm=http://www.w3.org/2001/04/xmldsig -more#rsa-sha256/><ds:Re ference><ds:Transforms><ds:Transform Algorithm="http://www.w3.org/2001/10/xml -ex c-c14n#"/></ds:Transforms><ds:DigestMethod Algorithm=http://www.w3.org/2001/04/x mlenc#sha256/><ds:DigestValue>dHLkPm5pcyBub3QgYSBzaWduYXR1cmGB</ds:DigestValue>< /ds:Reference></ds:SignedInfo><ds:SignatureValue>dHLkPm5pcyBub3QgYSBzaWduYXR1cmG B</ds:SignatureValue><ds:KeyInfo><ds:X509Data><ds:X509SubjectName>CN=gsma, O=GSM A, C=UK</ds:X509SubjectName></ds:X509Data></ds:KeyInfo></ds:Signature>

NOTE          All examples in this specification are not trimmed, for better readability.

B.2.2 Security

To secure the messages being sent between Function requester and Function provider, one of the two following mechanisms SHALL be used:

    Relying on mutual authenticated transport level security (Transport Layer Security,
     TLS)
    Relying on transport level security (TLS) with only server side authentication and WS-
     Security standards

This specification mandates usage of TLS v 1.2 defined in RFC 5246 [15] to allow appropriate algorithm and key length as defined in section 2.4.1.

B.2.2.1 Secure Channel Set-Up

The process of setting up secure channel is out of scope of this document. This process includes the exchange of the following information:

    Function requester and Function provider OIDs SHALL be registered and respective
     values have been communicated to each party
    Function requester and Function provider URL SHALL have been communicated to
     each party
    Function requester and Function provider SHALL agree on the MEP for response
     handling of asynchronous function: Asynchronous Request-Response with callback
     or Asynchronous with polling.
    Function requester and Function provider SHALL agree on the type of security
     mechanism used and respective credential:
   WS-Security
If UsernameToken Profile is used, the Username and Password SHALL be setup
at receiving entities.
If X509 Certificate Token Profile is used, the receiving entity SHALL trust the
sending entity issued certificate.
    Transport Level Security
Function requester and Function provider party trust must have been established
on a X509 certificate chain basis.
   Function requester and Function provider SHALL agree on the WSDL, which SHALL
    consist in the WSDL specified in section B.4, with the addition of the <Policy>
    elements implied by the the WS-Security if any, and complying with the WS-Security
    elements specified in section B.2.2.2

NOTE:Receiving entity and sending entity could either be the Function requester of the Function provider.

B.2.2.2 Identification/Authentication/Authorisation

Authentication of the sending party of a SOAP message SHALL rely on either the Transport layer security (using TLS certificate of the sending party) or the WS-Security [44]. In this latter case the SOAP message SHALL include specific WS-Security elements containing a security token, UserNameToken or X509Token as agreed during secure channel set-up (see 2.3.1).

Message receiver SHALL be able to process Web Service Security tokens as specified in the OASIS specification [44], specifically:

      UsernameToken Profile 1.1. as defined in [45]. Example:
<S11:Envelope xmlns:S11="..." xmlns:wsse="...">
          <S11:Header>
             …
                 <wsse:Security>
                        <wsse:UsernameToken>
                               <wsse:Username>ACompany</wsse:Username>
                               <wsse:Password>MyPassword</wsse:Password>
                        </wsse:UsernameToken>
                        …
                 </wsse:Security>
       ….
      X509 Certificate Token Profile 1.1. as defined in [46], with ‘#X509v3’ token type. The
       X509 certificate of the sender SHALL be included as a BinarySecurityToken. In order
       to prove that the sender owns the corresponding private key, the SOAP message
       SHALL then include a <ds:Signature> with the following properties:
   A <ds:SignedInfo> element in context of WS-Security X.509 certificate token
    profile specifying:
     a canonicalization method,
        This specification mandates the support of the following method
        ‘http://www.w3.org/2001/10/xml-exc-c14n#’
     a signature method; this specification mandates usage of one of the following
        signature method to have a compliant level of security (RSA and EC key
        length following recommendation given in section 2.3.3)
        http://www.w3.org/2001/04/xmldsig-more#rsa-sha256
        http://www.w3.org/2001/04/xmldsig-more#rsa-sha384
        http://www.w3.org/2001/04/xmldsig-more#rsa-sha512
        http://www.w3.org/2001/04/xmldsig-more#ecdsa-sha256
        http://www.w3.org/2001/04/xmldsig-more#ecdsa-sha384
        http://www.w3.org/2001/04/xmldsig-more#ecdsa-sha512
   at least one <ds:Reference> element pointing to the BinarySecurityToken (see
    note); and with a digesting method as one of:
        http://www.w3.org/2001/04/xmlenc#sha256
        http://www.w3.org/2001/04/xmldsig-more#sha384
        http://www.w3.org/2001/04/xmlenc#sha512
   including a <ds:Transforms> element with a <ds:Transform> element to
    specify the canonicalization method for the reference.
    This specification mandates the support of the following method
    ‘http://www.w3.org/2001/10/xml-exc-c14n#’
NOTE         Including the X.509 token in the signature is recommended by Oasis’ Web
             Services Security: SOAP Message Security 1.1 [44], to protects against
             certificate substitution attacks.

Example:

<S11:Envelope xmlns:S11="...">
       <S11:Header>
               …
               <wsse:Security xmlns:wsse="..." xmlns:wsu="..." >
                      <wsse:BinarySecurityToken ValueType="…#X509v3"
                              EncodingType="…#Base64Binary" wsu:Id="binarytoken">
                              MIIEZzCCA9CgAwIBAgIQEmtJZc0…
                      </wsse:BinarySecurityToken>
                                    <ds:Signature
xmlns:ds="http://www.w3.org/2000/09/xmldsig#">
                              <ds:SignedInfo>
                             <ds:CanonicalizationMethod
Algorithm=http://www.w3.org/2001/10/xml-exc-c14n#/>
                             <ds:SignatureMethod
Algorithm=http://www.w3.org/2001/04/xmldsig-more#rsa-sha256/>
                                    <ds:Reference URI="#binarytoken">
                                             <ds:Transforms>
                                                    <ds:Transform Algorithm="http://w
ww.w3.org/2001/10/xml-exc-c14n#" />
                                            </ds:Transforms>
                                   <ds:DigestMethod
Algorithm=http://www.w3.org/2001/04/xmlenc#sha256/>
                                             <ds:DigestValue>dHLk..</ds:DigestValue>
                                     </ds:Reference>
                              </ds:SignedInfo>
                              <ds:SignatureValue>HFLP…</ds:SignatureValue>
                              <ds:KeyInfo>
                                     <wsse:SecurityTokenReference>
                                             <wsse:Reference URI="#binarytoken" />
                                     </wsse:SecurityTokenReference>
                              </ds:KeyInfo>
                       </ds:Signature>
               </wsse:Security>
               …

B.2.2.3 Integrity

The integrity of the message SHALL exclusively rely on the transport level security (TLS).

B.2.2.4 Confidentiality

The confidentiality of the message SHALL exclusively rely on the transport level security (TLS).

B.2.3 Message Exchange Pattern (MEPs) – HTTPS Binding

B.2.3.1 MEP: Synchronous Request-Response

                    (1) HTTP POST + request
 Function                                               Function
requester                                               Provider
                    (2) HTTP 200 (OK) + Response

Figure 142: MEP: Synchronous Request-Response

(1) The SOAP header of the message sent in a HTTP POST from Function requester to Function provider SHALL contain:

/wsa:From (REQUIRED)

/wsa:To (REQUIRED)

/wsa:MessageID (REQUIRED)

/wsa:Action (REQUIRED)

(2) The response to the message is on the HTTP(s) return channel with code 200 (OK) and the SOAP header SHALL contain:

/wsa:From (OPTIONAL)

/wsa:To (REQUIRED)

/wsa:MessageID (REQUIRED)

/wsa:Action (REQUIRED)

B.2.3.2 MEP: Asynchronous Request-Response With Callback

(1) HTTP POST + request

                (2) HTTP 202 (ACCEPT)
 Function                                             Function
requester                                             Provider
                   (3) HTTP POST + response

(4) HTTP 202 (ACCEPT)

Figure 143: MEP: Asynchronous Request-Response With Callback

(1) The SOAP header of the message sent in a HTTP POST from Function requester to Function provider SHALL contain:

/wsa:From (REQUIRED)

/wsa:To (REQUIRED)

/wsa:ReplyTo (OPTIONAL)

/wsa:MessageID (REQUIRED)

/wsa:Action (REQUIRED)

(7)    The Function requester SHALL be able to handle 202 (ACCEPT) HTTP response
codes.

NOTE:In case the response is 200 (OK) steps (3) and (4) will be skipped if it is not a new session.

(3) The response to the message is sent in a HTTP POST from Function provider to Function requester, and the SOAP header SHALL contain:

/wsa:From (REQUIRED)

/wsa:To (REQUIRED)

/wsa:MessageID (REQUIRED)

/wsa:Action (REQUIRED)

/wsa:RelatesTo (Value of <wsa:MessageId> of the original message to which this is the
response) (REQUIRED)

(4) Function requester SHALL reply with a HTTP 202 (ACCEPT).

B.2.3.3 MEP: Asynchronous With Polling

(1) HTTP POST + request
With /wsa:ReplyTo Anonymous

(2) HTTP 202 (ACCEPT)

                           (3) HTTP POST
                       With /wsmc:MakeConnection
 Function                                                 Function
requester              (4) HTTP 202 (ACCEPT)              Provider
                         For empty response
    (5) HTTP POST
With /wsmc:MakeConnection

(6) HTTP 202 + response

Figure 144: MEP: Asynchronous With Polling

(1) The SOAP header of the message sent in a HTTP POST from Function requester to Function provider SHALL contain:

/wsa:From (REQUIRED)

/wsa:To (REQUIRED)

/wsa:ReplyTo (REQUIRED) containing one of the two possible anonymous URL (see
Annex B-Section 2.1.2)

/wsa:MessageID (REQUIRED)

/wsa:Action (REQUIRED)

(2) Function provider SHALL reply with a HTTP 202 (ACCEPT). (3 or 5) Function provider makes a WS-MakeConnection call as defined in Annex B-Section 2.1.2 with a header containing:

      <wsa:Action>http://docs.oasis-open.org/ws-
rx/wsmc/200702/MakeConnection<wsa:Action>
And a body containing:
          <wsmc:MakeConnection ...>
            <wsmc:Address>AnonymousURL                  (same       value   as     /wsa:ReplyTo
above)</wsmc:Address>
          </wsmc:MakeConnection>
(4 or 6) The response to the message is sent in a HTTP response from Function provider to
Function requester, and the SOAP header SHALL contain:

/wsa:From (REQUIRED)

/wsa:To (REQUIRED)

/wsa:MessageID (REQUIRED)

/wsa:Action (REQUIRED)

/wsa:RelatesTo (Value of <wsa:MessageId> of the original message to which this is the
response) (REQUIRED)

B.2.3.4 MEP: Notification (One-Way)

                   (1) HTTP POST + notification
 Function                                                 Function
requester                                                 Provider
                         (2) HTTP 202 (ACCEPT)

Figure 145: MEP: Synchronous Request-Response

(1) The SOAP header of the message sent in a HTTP POST from Function requester to Function provider SHALL contain:

/wsa:From (REQUIRED)

/wsa:To (REQUIRED)

/wsa:MessageID (REQUIRED)

/wsa:Action (REQUIRED)

(2) The response to the message is on the HTTP return channel with code 202 (ACCEPT) and with an empty body.

B.2.4 Binding Examples

B.2.4.1 Binding of a Message for ES4.EnableProfile Function Request

The xml hereunder illustrates an RPS message for requesting the execution of the ES4.EnableProfile function:

<?xml version="1.0" encoding="UTF-8"?>
<RPSMessage xmlns="http://namespaces.gsma.org/esim-messaging/1"
       xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
       MessageVersion="1.0.0">
       <RPSHeader>
            <SenderEntity>
                <EntityId>1.3.6.1.4.1.111111</EntityId><!-- Sample OID               -->
                <EntityName>ACompany</EntityName>
            </SenderEntity>
            <SenderName>aSenderAccountId</SenderName>
            <ReceiverEntity>
                <EntityId>1.3.6.1.4.1.222222</EntityId><!-- Sample OID -->
            </ReceiverEntity>
<ResponseEndpoint>http://ACompany.com/RPS/MyEndPoint</ResponseEndpoint>
            <TransactionId>MyTransID1</TransactionId>
            <MessageId>//MySenderDomain/123</MessageId>
            <MessageType>ES4-EnableProfileRequest</MessageType>
            <MessageDate>2013-04-18T09:30:47Z</MessageDate>
       </RPSHeader>
       <RPSBody>
            <ES4-EnableProfileRequest>
                <FunctionCallIdentifier>callId:1</FunctionCallIdentifier>
                <ValidityPeriod>3600</ValidityPeriod>
                <Eid>89001012012341234012345678901224</Eid>
                <ICCID>8933010000000000001</ICCID>
            </ES4-EnableProfileRequest>
       </RPSBody>
</RPSMessage>

In the case where:

 security is set with TLS, with mutual authentication based on certificate  the MEP is : Asynchronous Request-Response with callback This function execution request is bound to the following SOAP message:

<?xml version="1.0" encoding="UTF-8"?>
<s:Envelope               xmlns:s="http://www.w3.org/2003/05/soap -envelope"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:wsa="http://schemas.xmlsoap.org/ws/2004/08/addressing"
       xmlns:rps3="http://namespaces.gsma.org/esim-messaging/3">
       <s:Header>
           <wsa:From>
<wsa:Address>http://ACompany.com/RPS?EntityId=1.3.6.1.4.1.111111?EntityName
=ACompany?UserName=aSenderAccountID</wsa:Address>
           </wsa:From>

<wsa:To>http://AnotherCompany.com?EntityId=1.3.6.1.4.1.222222</wsa:To>

<wsa:MessageID>//MySenderDomain/123?TransactionId=MyTransID1?MessageDate=20
13-04-18T09:30:47Z</wsa:MessageID>
        <wsa:Action>http://gsma.com/ES4/ProfileManagement/ES4-
EnableProfile</wsa:Action>
           <wsa:ReplyTo>
               <wsa:Address>http://ACompany.com/RPS/MyEndPoint</wsa:Address>
           </wsa:ReplyTo>
       </s:Header>
       <s:Body rps3:MessageVersion="1.0.0">
           <rps3:ES4-EnableProfileRequest>
<rps3:FunctionCallIdentifier>callID:1</rps3:FunctionCallIdentifier>
               <rps3:ValidityPeriod>3600</rps3:ValidityPeriod>
               <rps3:Eid> 89001012012341234012345678901224</rps3:Eid>
               <rps3:ICCID>8933010000000000001</rps3:ICCID>
           </rps3:ES4-EnableProfileRequest>
       </s:Body>
</s:Envelope>

B.2.4.2 Binding of a Message for ES4.EnableProfile Function Response

The xml hereunder illustrates a possible message response for the ES4.EnableProfile function execution request illustrated in the example of the previous section 2.2.1:

<?xml version="1.0" encoding="UTF-8"?>

<RPSMessage xmlns="http://namespaces.gsma.org/esim-messaging/1"
       xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
       MessageVersion="1.0.0">
       <RPSHeader>
           <SenderEntity>
               <EntityId>1.3.6.1.4.1.222222</EntityId><!-- Sample OID                -->
           </SenderEntity>
           <SenderName>AnotherSenderAccountId</SenderName>
           <ReceiverEntity>
               <EntityId>1.3.6.1.4.1.111111</EntityId><!-- Sample OID -->
           </ReceiverEntity>
           <TransactionId>MyTransID1</TransactionId>
           <MessageId>//MyProviderDomain/99</MessageId>
           <MessageType>ES4-EnableProfileResponse</MessageType>
           <RelatesTo>//MySenderDomain/123</RelatesTo>
           <MessageDate>2013-04-18T09:45:00Z</MessageDate>
       </RPSHeader>
       <RPSBody>
           <ES4-EnableProfileResponse>
               <FunctionExecutionStatus>
                      <Status>EXECUTED_SUCCESS</Status>
               </FunctionExecutionStatus>
           </ES4-EnableProfileResponse>
       </RPSBody>
</RPSMessage>
In the context described in the example of the previous section 2.2.1, the function execution
response is bound to the following SOAP message:
<?xml version="1.0" encoding="UTF-8"?>
<s:Envelope xmlns:s="http://www.w3.org/2003/05/soap-envelope"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:wsa="http://schemas.xmlsoap.org/ws/2004/08/addressing"
xmlns:rps3="http://namespaces.gsma.org/esim-messaging/1">
  <s:Header>
       <wsa:From>
<wsa:Address>http://AnotherCompany.com/RPS?EntityId=1.3.6.1.4.1.222222?User
Name=AnotherSenderAccountId</wsa:Address>
    </wsa:From>
    <wsa:To>http://AnotherCompany.com?EntityId=1.3.6.1.4.1.111111</wsa:To>
    <wsa:MessageID>
//MyProviderDomain/99?TransactionId=MyTransID1?MessageDate=2013-04-
18T09:45:00Z</wsa:MessageID>
    <wsa:Action>http://gsma.com/ES4/PlatformManagement/ES4 -
EnableProfile</wsa:Action>
    <wsa:RelatesTo>
//MySenderDomain/123?TransactionId=MyTransID1?MessageDate=2013 -04-
18T09:30:47Z //MySenderDomain/123
    </wsa:RelatesTo><!-- Matching request in section B.2.4.1 -->
  </s:Header>
  <s:Body rps3:MessageVersion="1.0.0">
    <rps3:ES4-EnableProfileResponse>
      <rps3:FunctionExecutionStatus>
        <rps3:Status>EXECUTED_SUCCESS</rps3:Status>
      </rps3:FunctionExecutionStatus>
    </rps3:ES4-EnableProfileResponse>
  </s:Body>
</s:Envelope>

B.2.5 URI – query structure

The URI specification [65] treats the query part as being unstructured. The following rules SHALL be applied for query in URI:

     The query is composed of a series of field key-value pairs.
     Within each pair, the field key and the value are separated by an equals sign, "=".
     The series of pairs is separated by a questionmark, "?".

Examples: http://ACompany.com/RPS?EntityId=1.3.6.1.4.1.11111?EntityName=ACompany?User Name=aSenderAccountId where EntityId=1.3.6.1.4.1.11111?EntityName=ACompany?UserName=aSenderAccountId represents the whole query and EntityName=ACompany is one field name-value pair.

B.3 Function Binding

NOTE:In the tables below the Asynchronous Request-Response with Callback MEP can be replaced by an Asynchronous Request-Response with Polling MEP. In this case the /wsa:Action value has to be updated accordingly.

B.3.1 ES1

Function name                                      Binding Information
MEP            Synchronous Request-Response
                                /w sa:Action   http://gsma.com/ES1/eUICCManagement/ES1-RegisterEISRequest
RegisterEIS
                                Request
/w sa:Action   http://gsma.com/ES1/eUICCManagement/ES1-RegisterEISResponse

Response

                                Binding        Synchronous Request-Response
                                Information
UpdateEISAdditionalProperties
                     http://gsma.com/ES1/eUICCManagement/ES1-
/w sa:Action
                     UpdateEISAdditionalPropertiesRequest
Request
/w sa:Action         http://gsma.com/ES1/eUICCManagement/ES1-
                     UpdateEISAdditionalPropertiesResponse
Response

Table 227: ES1 Function Binding

B.3.2 ES2

Function name                                         Binding Information
MEP                       Synchronous Request-Response
                                                            http://gsma.com/ES2/DataPreparation/ES2-
GetEIS                            /w sa:Action Request      GetEISRequest
                          http://gsma.com/ES2/DataPreparation/ES2-
/w sa:Action
                          GetEISResponse
Response
MEP                       Asynchronous Request-Response with CallBack
                                                            http://gsma.com/ES2/ProfileManagement/ES2-
DownloadProfile                   /w sa:Action Request      DownloadProfile
                          http://gsma.com/ES2/ProfileManagementCallback/ES2-
/w sa:Action
                          DownloadProfile
Response
MEP                       Synchronous Request-Response
                                                            http://gsma.com/ES2/ProfileManagement/ES2-
UpdatePolicyRules                 /w sa:Action Request      UpdatePolicyRulesRequest
                          http://gsma.com/ES2/ProfileManagement/ES2-
/w sa:Action              UpdatePolicyRulesResponse
Response
MEP                       Synchronous Request-Response
                                                            http://gsma.com/ES2/ProfileManagement/ES2-
UpdateSubscriptionAddress         /w sa:Action Request      UpdateSubscriptionAddressRequest
                          http://gsma.com/ES2/ProfileManagement/ES2-
/w sa:Action              UpdateSubscriptionAddressResponse
Response
MEP                       Asynchronous Request-Response with CallBack
                                                            http://gsma.com/ES2/PlatformManagement/ES2-
EnableProfile                     /w sa:Action Request      EnableProfile
                          http://gsma.com/ES2/PlatformManagementCallback/ES2
/w sa:Action
                          -EnableProfile
Response
MEP                       Asynchronous Request-Response with CallBack
DisableProfile
                                                            http://gsma.com/ES2/PlatformManagement/ES2-
                                  /w sa:Action Request      DisableProfile
                        http://gsma.com/ES2/PlatformManagementCallback/ES2
/w sa:Action
                        -DisableProfile
Response
MEP                     Asynchronous Request-Response with CallBack
                                                               http://gsma.com/ES2/PlatformManagement/ES2-
DeleteProfile                          /w sa:Action Request    DeleteProfile
                        http://gsma.com/ES2/PlatformManagementCallback/ES2
/w sa:Action            -DeleteProfile
Response
MEP                     Notification (One-Way)
                                                               http://gsma.com/ES2/PlatformManagement/ES2-
HandleProfileDisabledNotification      /w sa:Action Request    HandleProfileDisabledNotification
/w sa:Action            (none)
Response
MEP                     Notification (One-Way)
                                                               http://gsma.com/ES2/PlatformManagement/ES2-
HandleProfileEnabledNotification       /w sa:Action Request    HandleProfileEnabledNotification
/w sa:Action            (none)
Response
MEP                     Notification (One-Way)
HandleSMSRChangeNotification                                   http://gsma.com/ES2/PlatformManagement/ES2-
                                       /w sa:Action Request    HandleSMSRChangeNotification
/w sa:Action            (none)
Response
MEP                     Notification (One-Way)
                                                               http://gsma.com/ES2/PlatformManagement/ES2-
HandleProfileDeletedNotification       /w sa:Action Request    HandleProfileDeletedNotification
/w sa:Action            (none)
Response
                        Asynchronous Request-Response with CallBack
MEP
                                                               http://gsma.com/ES2/ProfileManagement/ES2-AuditEIS
                                       /w sa:Action Request
AuditEIS
                                                               http://gsma.com/ES2/ProfileManagementCallBack/ES2-
                                       /w sa:Action Response   AuditEIS
                        Asynchronous Request-Response with CallBack
MEP
                                                               http://gsma.com/ES2/ProfileManagement/ES2-
                                       /w sa:Action Request    SetFallBackAttribute
SetFallBackAttribute
                        http://gsma.com/ES2/ProfileManagementCallBack/ES2-
/w sa:Action Response   SetFallBackAttribute
                                                               Notification (One-Way)
                                       MEP
HandleProfileFallBackAttributeSetNot
                                                               http://gsma.com/ES2/ProfileManagement/ES2-
ification
                                       /w sa:Action Request    HandleProfileFallBackAttributeSetNotification
                        (none)
/w sa:Action Response
                        Notification (One-Way)
MEP
                                                              http://gsma.com/ES2/ProfileManagement/ES2-
HandleProfileFallBackAttributeUnset   /w sa:Action Request    HandleProfileFallBackAttributeUnsetNotification
Notification
                        (none)
/w sa:Action Response
                        Asynchronous Request-Response with CallBack
MEP
                                                              http://gsma.com/ES2/ProfileManagement/ES2-
                                      /w sa:Action Request    SetEmergencyProfileAttribute
SetEmergencyProfileAttribute
                        http://gsma.com/ES2/ProfileManagementCallBack/ES2-
/w sa:Action Response   SetEmergencyProfileAttribute
                        Notification (One-Way)
MEP
                                                              http://gsma.com/ES2/ProfileManagement/ES2-
HandleEmergencyProfileAttributeSet    /w sa:Action Request    HandleEmergencyProfileAttributeSetNotification
Notification
                        (none)
/w sa:Action Response
                        Notification (One-Way)
MEP
                                                              http://gsma.com/ES2/ProfileManagement/ES2-
HandleEmergencyProfileAttributeUns /w sa:Action Request       HandleEmergencyProfileAttributeunSetNotification
etNotification
                        (none)
/w sa:Action Response
                        Synchronous Request-Response
MEP
                                                              http://gsma.com/ES2/ProfileManagement/ES2-
                                      /w sa:Action Request    GetONCRequest
GetONC
                        http://gsma.com/ES2/ProfileManagement/ES2-
/w sa:Action Response   GetONCResponse
                        Synchronous Request-Response
MEP
                                                              http://gsma.com/ES2/ProfileManagement/ES2-
                                      /w sa:Action Request    SetONCRequest
SetONC
                        http://gsma.com/ES2/ProfileManagement/ES2-
/w sa:Action Response   SetONCResponse
                        Synchronous Request-Response
MEP
                                                              http://gsma.com/ES2/ProfileManagement/ES2-
                                      /w sa:Action Request    GetPLMARequest
GetPLMA
                        http://gsma.com/ES2/ProfileManagement/ES2-
/w sa:Action Response   GetPLMAResponse
                        Synchronous Request-Response
MEP
SetPLMA                                                       http://gsma.com/ES2/ProfileManagement/ES2-
                                      /w sa:Action Request    SetPLMARequest
                          http://gsma.com/ES2/ProfileManagement/ES2-
/w sa:Action Response     SetPLMAResponse
                          Notification (One-Way)
MEP
                                                                http://gsma.com/ES2/ProfileManagement/ES2-
                                      /w sa:Action Request      HandleProfileDownloadedNotification
HandleProfileDownloadedNotification
/w sa:Action              (none)
Response
                          Notification (One-Way)
MEP
                                                                http://gsma.com/ES2/ProfileManagement/ES2-
                                      /w sa:Action Request      HandlePLMAChangedNotification
HandlePLMAChangedNotification
/w sa:Action              (none)
Response
                          Notification (One-Way)
MEP
                                                                http://gsma.com/ES2/ProfileManagement/ES2-
                                                                HandlePolicyRulesUpdatedNotification
HandlePolicyRulesUpdatedNotificatio /w sa:Action Request
n
                                      /w sa:Action              (none)
                                      Response

Table 228: ES2 Function Binding

B.3.3 ES3

Function name                                           Binding Information
MEP                     Synchronous Request-Response
                                                              http://gsma.com/ES3/ProfileManagement/ES3-
                                      /w sa:Action Request
                                                              GetEISRequest
GetEIS
                        http://gsma.com/ES3/ProfileManagement/ES3-
/w sa:Action Response
                        GetEISResponse
MEP                     Asynchronous Request-Response with CallBack
                                      /w sa:Action Request    http://gsma.com/ES3/ProfileManagement/ES3-AuditEIS
AuditEIS
                        http://gsma.com/ES3/ProfileManagementCallBack/ES3-
/w sa:Action Response
                        AuditEIS
MEP                     Asynchronous Request-Response with CallBack
                                      /w sa:Action Request    http://gsma.com/ES3/ProfileManagement/ES3-CreateISDP
CreateISDP
                        http://gsma.com/ES3/ProfileManagemenCallBack/ES3 -
/w sa:Action Response
                        CreateISDP
MEP                     Asynchronous Request-Response with CallBack
                               /w sa:Action Request    http://gsma.com/ES3/ProfileManagement/ES3-SendData
SendData
                        http://gsma.com/ES3/ProfileManagementCallBack/ES3-
/w sa:Action Response
                        SendData
MEP                     Synchronous Request-Response
                                                       http://gsma.com/ES3/ProfileManagement/ES3-
                               /w sa:Action Request
ProfileDownloadCompleted                               ProfileDownloadedCompletedRequest
                        http://gsma.com/ES3/ProfileManagement/ES3-
/w sa:Action Response
                        ProfileDownloadedCompletedResponse
MEP                     Synchronous Request-Response
                                                       http://gsma.com/ES3/ProfileManagement/ES3-
                               /w sa:Action Request
UpdatePolicyRules                                      UpdatePolicyRulesRequest
                        http://gsma.com/ES3/ProfileManagement/ES3-
/w sa:Action Response
                        UpdatePolicyRulesResponse
MEP                     Synchronous Request-Response
                                                       http://gsma.com/ES3/ProfileManagement/ES3-
                               /w sa:Action Request
UpdateSubscriptionAddress                              UpdateSubscriptionAddressRequest
                        http://gsma.com/ES3/ProfileManagement/ES3-
/w sa:Action Response
                        UpdateSubscriptionAddressResponse
MEP                     Asynchronous Request-Response with CallBack
                                                       http://gsma.com/ES3/PlatformManagement/ES3 -
                               /w sa:Action Request
EnableProfile                                          EnableProfile
                        http://gsma.com/ES3/PlatformManagementCallBack/ES3 -
/w sa:Action Response
                        EnableProfile
MEP                     Asynchronous Request-Response with CallBack
                                                       http://gsma.com/ES3/PlatformManagement/ES3 -
                               /w sa:Action Request
DisableProfile                                         DisableProfile
                        http://gsma.com/ES3/PlatformManagementCallBack/ES3 -
/w sa:Action Response
                        DisableProfile
MEP                     Asynchronous Request-Response with CallBack
                                                       http://gsma.com/ES3/PlatformManagement/ES3 -
                               /w sa:Action Request
DeleteISDP                                             DeleteISDP
                        http://gsma.com/ES3/PlatformManagementCallBack/ES3 -
/w sa:Action Response
                        DeleteISDP
UpdateConnectivityParameters   MEP                     Asynchronous Request-Response with CallBack
                        http://gsma.com/ES3/PlatformManagement/ES3 -
/w sa:Action Request
                        UpdateConnectivityParameters
                        http://gsma.com/ES3/PlatformManagementCallBack/ES3 -
/w sa:Action Response
                        UpdateConnectivityParameters
MEP                     Notification (One-Way)
                                                              http://gsma.com/ES3/PlatformManagement/ES3 -
HandleProfileDisabledNotification     /w sa:Action Request
                                                              HandleProfileDisabledNotification

/w sa:Action Response (none)

MEP                     Notification (One-Way)
                                                              http://gsma.com/ES3/PlatformManagement/ES3 -
HandleProfileEnabledNotification      /w sa:Action Request
                                                              HandleProfileEnabledNotification

/w sa:Action Response (none)

MEP                     Notification (One-Way)
                                                              http://gsma.com/ES3/PlatformManagement/ES3 -
HandleSMSRChangeNotification          /w sa:Action Request
                                                              HandleSMSRChangeNotification

/w sa:Action Response (none)

MEP                     Notification (One-Way)
                                                              http://gsma.com/ES3/PlatformManagement/ES3 -
HandleProfileDeletedNotification      /w sa:Action Request
                                                              HandleProfileDeletedNotification

/w sa:Action Response (none)

MEP                     Asynchronous Request-Response with CallBack
                                                              http://gsma.com/ES3/ProfileManagement/ES3-
                                      /w sa:Action Request
SetFallBackAttribute                                          SetFallBackAttribute
                        http://gsma.com/ES3/ProfileManagementCallBack/ES3-
/w sa:Action Response
                        SetFallBackAttribute
MEP                     Notification (One-Way)
HandleProfileFallBackAttributeSetNot                          http://gsma.com/ES3/ProfileManagement/ES3-
                                     /w sa:Action Request
ification                                                     HandleProfileFallBackAttributeSetNotification

/w sa:Action Response (none)

MEP                     Notification (One-Way)
HandleProfileFallBackAttributeUnset                           http://gsma.com/ES2/ProfileManagement/ES3-
                                      /w sa:Action Request
Notification                                                  HandleProfileFallBackAttributeUnsetNotification

/w sa:Action Response (none)

SetEmergencyProfileAttribute          MEP                     Asynchronous Request-Response with CallBack
                        http://gsma.com/ES3/ProfileManagement/ES3-
/w sa:Action Request
                        SetEmergencyProfileAttribute
                        http://gsma.com/ES3/ProfileManagementCallBack/ES3-
/w sa:Action Response
                        SetEmergencyProfileAttribute
MEP                     Notification (One-Way)
HandleEmergencyProfileAttributeSet                           http://gsma.com/ES3/ProfileManagement/ES3-
                                     /w sa:Action Request
Notification                                                 HandleEmergencyProfileAttributeSetNotification

/w sa:Action Response (none)

MEP                     Notification (One-Way)
HandleEmergencyProfileAttributeUns                           http://gsma.com/ES3/ProfileManagement/ES3-
                                   /w sa:Action Request
etNotification                                               HandleEmergencyProfileAttributeUnsetNotification

/w sa:Action Response (none)

MEP                     Synchronous Request-Response
                                                             http://gsma.com/ES3/ProfileManagement/ES3-
                                     /w sa:Action Request
GetONC                                                       GetONCRequest
                        http://gsma.com/ES3/ProfileManagement/ES3-
/w sa:Action Response
                        GetONCResponse
MEP                     Synchronous Request-Response
                                                             http://gsma.com/ES3/ProfileManagement/ES3-
                                     /w sa:Action Request
SetONC                                                       SetONCRequest
                        http://gsma.com/ES3/ProfileManagement/ES3-
/w sa:Action Response
                        SetONCResponse
MEP                     Synchronous Request-Response
                                                             http://gsma.com/ES3/ProfileManagement/ES3-
                                     /w sa:Action Request
GetPLMA                                                      GetPLMARequest
                        http://gsma.com/ES3/ProfileManagement/ES3-
/w sa:Action Response
                        GetPLMAResponse
MEP                     Synchronous Request-Response
                                                             http://gsma.com/ES3/ProfileManagement/ES3-
                                     /w sa:Action Request
SetPLMA                                                      SetPLMARequest
                        http://gsma.com/ES3/ProfileManagement/ES3-
/w sa:Action Response
                        SetPLMAResponse
MEP                     Notification (One-Way)
                                                             http://gsma.com/ES3/ProfileManagement/ES2-
HandleProfileDownloadedNotification /w sa:Action Request
                                                             HandleProfileDownloadedNotification
/w sa:Action            (none)

Response

/w sa:Action
                        (none)
Response
HandlePLMAChangedNotification     MEP                     Notification (One-Way)
                        http://gsma.com/ES3/ProfileManagement/ES2-
/w sa:Action Request
                        HandlePLMAChangedNotification
                                  /w sa:Action
                                                          (none)
                                  Response
HandlePolicyRulesUpdatedNotificatio
n                                   MEP                   Notification (One-Way)
                        http://gsma.com/ES3/ProfileManagement/ES2-
/w sa:Action Request
                        HandlePolicyRulesUpdatedNotification

Table 229: ES3 Function Binding

B.3.4 ES4

Function name                                       Binding Information
MEP                     Synchronous Request-Response
                                                          http://gsma.com/ES4/ProfileManagement/ES4-
                                  /w sa:Action Request
                                                          GetEISRequest
GetEIS
                        http://gsma.com/ES4/ProfileManagement/ES4-
/w sa:Action Response
                        GetEISResponse
MEP                     Synchronous Request-Response
                                                          http://gsma.com/ES4/ProfileManagement/ES4-
                                  /w sa:Action Request
UpdatePolicyRules                                         UpdatePolicyRulesRequest
                        http://gsma.com/ES4/ProfileManagement/ES4-
/w sa:Action Response
                        UpdatePolicyRulesResponse
MEP                     Synchronous Request-Response
                                                          http://gsma.com/ES4/ProfileManagement/ES4-
                                  /w sa:Action Request
UpdateSubscriptionAddress                                 UpdateSubscriptionAddressRequest
                        http://gsma.com/ES4/ProfileManagement/ES4-
/w sa:Action Response
                        UpdateSubscriptionAddressResponse
MEP                     Asynchronous Request-Response with CallBack
                                  /w sa:Action Request    http://gsma.com/ES4/ProfileManagement/ES4-AuditEIS
AuditEIS
                        http://gsma.com/ES4/ProfileManagementCallBack/ES4-
/w sa:Action Response
                        AuditEIS
EnableProfile                     MEP                     Asynchronous Request-Response with CallBack
                        http://gsma.com/ES4/PlatformManagement/ES4 -
/w sa:Action Request
                        EnableProfile
                        http://gsma.com/ES4/PlatformManagementCallBack/ES4 -
/w sa:Action Response
                        EnableProfile
MEP                     Asynchronous Request-Response with CallBack
                                                            http://gsma.com/ES4/PlatformManagement/ES4 -
                                    /w sa:Action Request
DisableProfile                                              DisableProfile
                        http://gsma.com/ES4/PlatformManagementCallBack/ES4 -
/w sa:Action Response
                        DisableProfile
MEP                     Asynchronous Request-Response with CallBack
                                                            http://gsma.com/ES4/PlatformManagement/ES4 -
                                    /w sa:Action Request
DeleteProfile                                               DeleteProfile
                        http://gsma.com/ES4/PlatformManagementCallBack/ES4 -
/w sa:Action Response
                        DeleteProfile
MEP                     Asynchronous Request-Response with CallBack
                                                            http://gsma.com/ES4/eUICCManagement/ES4-
                                    /w sa:Action Request
PrepareSMSRChange                                           PrepareSMSRChange
                        http://gsma.com/ES4/eUICCManagementCallBack/ES4 -
/w sa:Action Response
                        PrepareSMSRChange
MEP                     Asynchronous Request-Response with CallBack
                                                            http://gsma.com/ES4/eUICCManagement/ES4-
                                    /w sa:Action Request
SMSRChange                                                  SMSRChange
                        http://gsma.com/ES4/eUICCManagementCallBack/ES4 -
/w sa:Action Response
                        SMSRChange
MEP                     Notification (One-Way)
                                                            http://gsma.com/ES4/PlatformManagement/ES4 -
HandleProfileDisabledNotification   /w sa:Action Request
                                                            HandleProfileDisabledNotification

/w sa:Action Response (none)

MEP                     Notification (One-Way)
                                                            http://gsma.com/ES4/PlatformManagement/ES4 -
HandleProfileEnabledNotification    /w sa:Action Request
                                                            HandleProfileEnabledNotification

/w sa:Action Response (none)

MEP                     Notification (One-Way)
                                                            http://gsma.com/ES4/eUICCManagement/ES4-
HandleSMSRChangeNotification        /w sa:Action Request
                                                            HandleSMSRChangeNotification

/w sa:Action Response (none)

MEP                     Notification (One-Way)
                                                              http://gsma.com/ES4/PlatformManagement/ES4 -
                                      /w sa:Action Request
                                                              HandleProfileDeletedNotification
HandleProfileDeletedNotification

/w sa:Action Response (none)

MEP                     Asynchronous Request-Response with CallBack
                                                              http://gsma.com/ES4/ProfileManagement/ES4-
SetFallBackAttribute                  /w sa:Action Request
                                                              SetFallBackAttribute
                        http://gsma.com/ES4/ProfileManagementCallBack/ES4-
/w sa:Action Response
                        SetFallBackAttribute
MEP                     Notification (One-Way)
HandleProfileFallBackAttributeSetNot                          http://gsma.com/ES4/ProfileManagement/ES4-
                                     /w sa:Action Request
ification                                                     HandleProfileFallBackAttributeSetNotification

/w sa:Action Response (none)

MEP                     Notification (One-Way)
HandleProfileFallBackAttributeUnset                           http://gsma.com/ES4/ProfileManagement/ES4-
                                      /w sa:Action Request
Notification                                                  HandleProfileFallBackAttributeUnsetNotification

/w sa:Action Response (none)

MEP                     Asynchronous Request-Response with CallBack
                                                              http://gsma.com/ES4/ProfileManagement/ES4-
SetEmergencyProfileAttribute          /w sa:Action Request
                                                              SetEmergencyProfileAttribute
                        http://gsma.com/ES4/ProfileManagementCallBack/ES4-
/w sa:Action Response
                        SetEmergencyProfileAttribute
HandleEmergencyProfileAttributeSet                            Notification (One-Way)
                                      MEP
Notification
                        http://gsma.com/ES4/ProfileManagement/ES4-
/w sa:Action Request
                        HandleEmergencyProfileAttributeSetNotification

/w sa:Action Response (none)

MEP                     Notification (One-Way)
HandleEmergencyProfileAttributeUns /w sa:Action Request       http://gsma.com/ES4/ProfileManagement/ES4-
etNotification                                                HandleEmergencyProfileAttributeUnsetNotification

/w sa:Action Response (none)

MEP                     Synchronous Request-Response
                                                              http://gsma.com/ES4/ProfileManagement/ES4-
                                      /w sa:Action Request
GetPLMA                                                       GetPLMARequest
                        http://gsma.com/ES4/ProfileManagement/ES4-
/w sa:Action Response
                        GetPLMAResponse
MEP                     Notification (One-Way)
                                                              http://gsma.com/ES4/ProfileManagement/ES2-
                                      /w sa:Action Request
HandleProfileDownloadedNotification                           HandleProfileDownloadedNotification
/w sa:Action
                        (none)
Response
MEP                     Notification (One-Way)
                                                              http://gsma.com/ES4/ProfileManagement/ES2-
                                      /w sa:Action Request
                                                              HandlePLMAChangedNotification
HandlePLMAChangedNotification
/w sa:Action
                        (none)
Response
MEP                     Notification (One-Way)
                                                              http://gsma.com/ES4/ProfileManagement/ES2-
HandlePolicyRulesUpdatedNotificatio /w sa:Action Request      HandlePolicyRulesUpdatedNotification
n
                                      /w sa:Action
                                                              (none)
                                      Response

Table 230: ES4 Functions Binding

B.3.5 ES7

Function name                                            Binding Information
MEP                   Asynchronous Request-Response with CallBack
                       /w sa:Action           http://gsma.com/ES7/eUICCManagement/ES7-CreateAdditionalKeySet
CreateAdditionalKeySet Request
/w sa:Action          http://gsma.com/ES7/eUICCManagementCallBack/ES7 -
Response              CreateAdditionalKeySet
MEP                   Asynchronous Request-Response with CallBack
                        /w sa:Action
                                              http://gsma.com/ES7/eUICCManagement/ES7-HandoverEUICC
HandoverEUICC           Request
/w sa:Action          http://gsma.com/ES7/eUICCManagementCallBack/ES7 -HandoverEUICC
Response
MEP                   Asynchronous Request-Response with CallBack
                        /w sa:Action          http://gsma.com/ES7/eUICCManagement/ES7-AuthenticateSMSR
AuthenticateSMSR        Request
/w sa:Action          http://gsma.com/ES7/eUICCManagementCallBack/ES7 -AuthenticateSMSR
Response

Table 231: ES7 Function Binding

B.3.6 ES4A

Function name                                          Binding Information
MEP                Synchronous Request-Response
                               /w sa:Action       http://gsma.com/ES4A/ProfileManagement/ES4A-GetONCRequest
GetONC                         Request
/w sa:Action       http://gsma.com/ES4A/ProfileManagement/ES4A-GetONCResponse
Response
MEP                Synchronous Request-Response
                               /w sa:Action
                                                  http://gsma.com/ES4A/ProfileManagement/ES4A-SetONCRequest
SetONC                         Request
/w sa:Action       http://gsma.com/ES4A/ProfileManagement/ES4A-SetONCResponse
Response
MEP                Synchronous Request-Response
                               /w sa:Action       http://gsma.com/ES4A/ProfileManagement/ES4A-GetPLMARequest
GetPLMA                        Request
/w sa:Action       http://gsma.com/ES4A/ProfileManagement/ES4A-GetPLMAResponse
Response
SetPLMA                        MEP                Synchronous Request-Response
/w sa:Action      http://gsma.com/ES4A/ProfileManagement/ES4A-SetPLMARequest
Request
/w sa:Action      http://gsma.com/ES4A/ProfileManagement/ES4A-SetPLMAResponse
Response

Table B37: ES4A Functions Binding

B.4 Web Service Description Language (WSDL)

The Web Services Description Language (WSDL) is an XML-based interface definition language that is used for describing the functionality offered by a web service. It provides a machine-readable description of how the service can be called, what parameters it expects, and what data structures it returns.

WSDL files are provided within the SGP.02 v4.0 WSDL.ZIP package.

This package is composed of the following WSDL files:

       ES1_SMSR.wsdl
       ES2_MNO.wsdl
       ES2_SMDP.wsdl
       ES3_SMDP.wsdl
       ES3_SMSR.wsdl
       ES4_MNO.wsdl
       ES4_SMSR.wsdl
       ES4A_SMSR.wsdl
       ES7_SMSR_Provider.wsdl
       ES7_SMSR_Requester.wsdl
These WDSL files reference XML schemafiles (.xsd), which are also provided within the
SGP.02 v4.0 WSDL.ZIP package.
These WSDL files define a version of Web Services API that does not leverage WS-
Security. In case the Function requester and Function provider agree on using WS-
Security, the WSDL files SHALL be modified by the addition of elements specifying the
WS-Security options agreed as per section B.2.2.

C Use of GlobalPlatform Privileges (Normative)

GlobalPlatform defines the following privileges:

Priv ilege        Priv ilege                                             Description
 Number
0       Security Domain         Application is a Security Domain.
1       DAP Verification        Application is capable of verifying a DAP; Security Domain privilege SHALL also be
                                set.
2     Delegated               Application is capable of Delegated Card Content Management: Security Domain
      Management              privilege SHALL also be set.
3     Card Lock               Application has the privilege to lock the card.
4     Card Terminate          Application has the privilege to terminate the card.
5     Card Reset              Application has the privilege to modify historical bytes on one or more card
                              interfaces.

This privilege was previously labelled "Default Selected".

6     CVM Management          Application has the privilege to manage a shared CVM of a CVM Application.
7     Mandated DAP            Application is capable of and requires the verification of a DAP for all load
      Verification            operations: Security Domain privilege and DAP Verification privilege SHALL also
                              be set.
8     Trusted Path            Application is a Trusted Path for inter-application communication.
9     Authorized              Application is capable of Card Content Management; Security Domain privilege
      Management              SHALL also be set.
10    Token Verification      Application is capable of verifying a token for Delegated Card Content
                              Management.
11    Global Delete           Application may delete any Card Content.
12    Global Lock             Application may lock or unlock any Application.
13    Global Registry         Application may access any entry in the GlobalPlatform Registry.
14    Final Application       The only Application accessible in card Life Cycle State CARD_LOCKED and
                              TERMINATED.
15    Global Service          Application provides services to other Applications on the card.
16    Receipt Generation      Application is capable of generating a receipt for Delegated Card Content
                              Management.
17    Ciphered Load File      The Security Domain requires that the Load File being associated to it is to be
      Data Block              loaded ciphered.
18    Contactless             Application is capable of activating and deactivating other Applications on the
      Activation              contactless interface.
19    Contactless Self-       Application is capable of activating itself on the contactless interface without a prior
      Activation              request to the Application with the Contactless Activation privilege.

Table 232: GlobalPlatform Privileges

Privileges description in an eUICC:

The following rules apply for an eUICC with at least one Profile installed.

Security Domain Privilege:

GlobalPlatform Card Specification [6] states: “This privilege distinguishes a Security Domain from a 'normal' Application.”

DAP Verification Privilege:

GlobalPlatform Card Specification [6] states: “An application provider may require that their Application code to be loaded on the card SHALL be checked for integrity and authenticity. The DAP Verification privilege provides this service on behalf of an Application provider.”

Delegated Management:

GlobalPlatform Card Specification [6] states: “The privilege allows an Application Provider to manage Card Content with authorisation.” A “Security Domain having the Token Verification privilege controls such authorisation.”

Card Lock:

GlobalPlatform Card Specification [6] states: “This privilege allows an Application to set the card life cycle state to CARD_LOCKED.”

On the eUICC, the Card Lock privilege is not applicable and SHALL NOT be assigned to any security domain/Application. The equivalent mechanism of disabling a Profile SHALL be used.

Card Terminate:

GlobalPlatform Card Specification [6] states: “This privilege allows an Application to set the card life cycle state to TERMINATED.”

On the eUICC, the Card Terminate privilege is not applicable and SHALL NOT be assigned to any security domain/Application. The equivalent mechanism of deleting a Profile SHALL be used.

Card Reset:

GlobalPlatform Card Specification [6] states: “An Application installed or made selectable with the Card Reset privilege and no Implicit Selection parameter is registered in the GlobalPlatform Registry as the implicitly selectable Application on the Basic Logical Channel for all card I/O interfaces supported by the card if no other Application (other than the Issuer Security Domain) is already registered as implicitly selectable on the Basic Logical Channel of any card I/O interface”.

This privilege is relevant only when the Profile is enabled. Therefore, several Applications may have this privilege on the eUICC, but this privilege SHALL be unique within a Profile.

If the Application inside a Profile with the Card Reset privilege is deleted the privilege is reassigned to the corresponding MNO-SD.

CVM Management:

GlobalPlatform Card Specification [6] states: “The CVM Application, if present on a card, provides a mechanism for a Cardholder Verification Method (CVM), including velocity checking, that may be used by all Applications on the card”.

If an Application in a Profile has this privilege, it SHALL be relevant only when the Profile is enabled. In that case, several Applications may have this privilege on the card, but this privilege SHALL be unique within a Profile.

Mandated DAP Verification:

GlobalPlatform Card Specification [6] states: “A Controlling Authority may require that all Application code to be loaded onto the card SHALL be checked for integrity and authenticity. The Mandated DAP Verification privilege of the Controlling Authority's Security Domain detailed in this Specification provides this service on behalf of the Controlling Authority”.

If an Application in a Profile has this privilege, it SHALL be relevant only when the Profile is enabled. In that case, several Applications may have this privilege on the card, but t his privilege SHALL be unique within a Profile.

The DAP verification is mandated only when loading an Application inside the Profile.

Trusted Path:

GlobalPlatform Card Specification [6] states: "The 'Trusted Path' privilege qualifies an Application as a Receiving Entity. Each Application present on the card playing the Role of a Receiving Entity SHALL: Enforce the Issuer's security rules for inter -application communication; Ensure that incoming messages are properly provided unaltered to the Trusted Framework; Ensure that any response messages are properly returned unaltered to the off-card entity”.

Authorised Management:

GlobalPlatform Card Specification [6] states: “Having a Security Domain with this privilege allows a Security Domain provider to perform Card Content management without authorisation (i.e. a token) in the case where the off-card entity is authenticated as the owner (Security Domain Provider) of the Security Domain”.

Token Verification:

GlobalPlatform Card Specification [6] states: “This privilege allows a Security Domain Provider, to authorize any Card Content management operation”.

This privilege SHALL be set to MNO-SD, if the Delegated Management privilege is used in the Profile.

Global Delete:

GlobalPlatform Card Specification [6] states: “This privilege provides the capability to remove any Executable Load File or Application from the card even if the Executable Load File or Application does not belong to this Security Domain”.

For MNO-SD and Applications inside a Profile, this privilege SHALL only allow deletion of Applications in the corresponding Profile.

Global Lock:

GlobalPlatform Card Specification [6] states: “This privilege provides the right to initiate the locking and unlocking of any Application on the card, independent of its Security Domain Association and hierarchy. It also provides the capability to restrict the Card Content Management functionality of OPEN”.

For MNO-SD and Applications inside a Profile, this privilege SHALL only allow locking of Applications in the corresponding Profile.

Global Registry:

GlobalPlatform Card Specification [6] states: “The search is limited to the Executable Load Files, Applications and Security Domains that are directly or indirectly associated with the eUICC entity receiving the command. When the eUICC entity receiving the command has the Global Registry privilege, the search applies to all Executable Load Files, Applications and Security Domains registered in the GlobalPlatform Registry”.

For ISD-P and Applications inside a Profile, this privilege SHALL only allow looking for Applications in the corresponding Profile.

Final Application:

GlobalPlatform Card Specification [6] states: “If a Security Domain has the Final Application privilege only the GET DATA command SHALL be processed, all other commands defined in this specification SHALL be disabled and SHALL return an error”.

On the eUICC, the Final Application privilege is not applicable and SHALL NOT b e assigned to any security domain/Application.

Global Service:

GlobalPlatform Card Specification [6] states: “One or more Global Services Applications may be present on the card to provide services to other Applications on the card.

The MNO-SD or Applications inside a Profile with the Global Service privilege SHALL offer service only when the Profile is enabled. Therefore, it is possible to have several Applications registered on the same service in the same eUICC.

Receipt Generation:

GlobalPlatform Card Specification [6] states: “This privilege allows a Security Domain Provider, typically the Card Issuer, to provide a confirmation for the performed card content management. A Security Domain with Receipt Generation privilege requires the knowledge of keys and algorithms used for Receipts generation”.

This privilege SHALL be set to MNO-SD, if the Delegated Management privilege is used in the Profile.

Ciphered Load File Data Block:

GlobalPlatform Card Specification [6] states: “This privilege allows a Security Domain Provider to require that the Load File Data Block being associated to it SHALL be ciphered”.

Contactless Activation:

GlobalPlatform Card Specification [6] states: “The Contactless Activation privilege identifies the CRS Application. This Privilege allows:

   The Activation/Deactivation of Applications on the Contactless Interface
   The update of the Selection Priority
     Manage the Volatile Priority
     Reorder the GlobalPlatform Registry
   Notification by the OPEN when:
     An Application is INSTALLED, LOCKED, unlocked or deleted
     The availability state of an Application is changed between NON_ACTIVATABLE,
       ACTIVATED, or DEACTIVATED.
     One of the Application’s contactless registry parameters is updated”.

If an Application in a Profile has this privilege, it SHALL be relevant only when the Profile is enabled. In that case, several Applications may have this privilege on the card, but this privilege SHALL be unique within a Profile.

Contactless Self-Activation:

GlobalPlatform Card Specification [6] states: “The Contactless Self-Activation Privilege allows an Application to activate itself without a prior request to the CRS Application”.

If an Application in a Profile has this privilege, it SHALL be relevant only when the Profile is enabled.

Priv ilege                                 ISD-   ISD-   MNO-   Applications inside a
                      Priv ilege                                                        ECASD
 Number                                      R     P      SD           Profile
    0        Security Domain               √      √       √                               √
1        DAP Verification
2        Delegated Management
3        Card Lock
4        Card Terminate
5        Card Reset
6        CVM Management                              √**
7        Mandated DAP Verification
8        Trusted Path                  √      √       √
9        Authorized Management                √*      √
10        Token Verification                          √***
11        Global Delete                               √**
12        Global Lock                                 √**
13        Global Registry                             √**
14        Final Application
15        Global Service                                                               √
16        Receipt Generation                          √***
17        Ciphered Load File Data
          Block
18        Contactless Activation
19        Contactless Self-Activation

Table 233: GlobalPlatform Application Privileges

A tick (√) denotes the presence of the indicated privilege and its assignment to the Security Domain or Application.

A blank cell denotes that the assignment of the privilege is managed by the owner of the Application (according to GlobalPlatform Card Specification [6]) of the Security Domain.

A black cell denotes that the privilege cannot be assigned.

* Authorized Management privilege is only set when ISD-P is in CREATED state to allow Profile Download and Installation.

** These privileges are mandatory for cards compliant to GlobalPlatform Card Specification UICC Configuration [7].

*** These privileges are mandatory for cards compliant to GlobalPlatform Card Specification UICC Configuration [7], if the Delegated Management privilege is used in the Profile.

D Data Definitions (Normative)

   Coding of the IMEI

The value of IMEI SHALL be directly copied from Terminal Response of the Provide Local Information command (see ETSI TS 102 223 [3] and ETSI TS 124 008[20]).

E EIS Usage in Functions (Normative)

This table gives additional information on the EIS usage depending on the function:

   Column ‘EUM Signed’: ‘X’ indicates if the data is part of the signature computed by
    the EUM at the initial registration time.
   Other columns:
   An ‘M’, ‘O’, ‘C’, indicates that the data is,respectively, Mandatory, Optional,
    Conditional, and that the entity processing the EIS SHALL be ready to receive the
    data
   An empty cell indicates that the data SHALL NOT be provided
                                                                     ES2.AuditEISES2.HandleSMSRChangeN
                                                               ES4.HandleSMSRChangeNotification
ES3.HandleSMSRChangeNotification
                                                                                                                                                                                                 ES7.HandoverEUICC
ES1.RegisterEIS

ES3.AuditEIS

                                                                                                                                                            ES4.AuditEIS
EUM Signed

ES2.GetEIS

ES3.GetEIS

                                                                                      ES4.GetEIS
otification

Data name

eid                                X            M                       M                                                       M                                                              M                                                 M
eum-id                             X            M                       M                                                       M                                                              M                                                 M
productionDate                     X            M                       M                                                       M                                                              M                                                 M
platformType                       X            M                       M                                                       M                                                              M                                                 M

ES2.AuditEISES2.HandleSMSRChangeN

                                                                 ES4.HandleSMSRChangeNotification
ES3.HandleSMSRChangeNotification
                                                                                                                                                                                                   ES7.HandoverEUICC
ES1.RegisterEIS

ES3.AuditEIS

                                                                                                                                                               ES4.AuditEIS
EUM Signed

ES2.GetEIS

ES3.GetEIS

                                                                                                                                                               ES4.GetEIS
                                                                         otification
Data name
platformVersion                 X             M                       M                                                       M                                                               M                                                  M
remainingMemory                               M                       M                                                       M                                                               M                                                  M
Availablememoryforprofiles                    M                       M                                                       M                                                               M                                                  M
lastAuditDate                                                          C                                                      C                                                               C                                                  C
smsr-id                                       M                       M                                                       M                                                               M                                                  M
isd-p-loadfile-aid              X             M                       M                                                       M                                                               M                                                  M
isd-p-module-aid                X             M                       M                                                       M                                                               M                                                  M
Profiles                                     M (1)                 O(3)                                                  O(3bis)                                                             M (3)                                               M
Iccid                                  M                       M                                                       M                                                               M                                                  M
isd-p-aid                              M                       M                                                       M                                                               M                                                  M
mno-id                                 M                       M                                                       M                                                               M                                                  M
fallbackAttribute                      M                       M                                                       M                                                               M                                                  M
subscriptionAddress                    M                       M                                                       M                                                               M                                                  M
State                                  M                       M                                                       M                                                               M                                                  M
smdp-id                                O                        C                                                      C                                                               C                                                  C
ProfileType                            O                        O                                                      O                                                               O                                                  O
allocatedMemory                        M                       M                                                       M                                                               M                                                  M
freeMemory                             C                        C                                                      C                                                               C                                                  C
pol2                                   M                       M                                                       M                                                               M                                                  M

ES2.AuditEISES2.HandleSMSRChangeN

                                                                 ES4.HandleSMSRChangeNotification
ES3.HandleSMSRChangeNotification
                                                                                                                                                                                                             ES7.HandoverEUICC
ES1.RegisterEIS

ES3.AuditEIS

                                                                                                                                                                      ES4.AuditEIS
EUM Signed

ES2.GetEIS

ES3.GetEIS

                                                                                                                                                                              ES4.GetEIS
                                                                                    otification
Data name
                                                         (2)                 (4)(7)                                                       (4)                                                             (4)(7)                                                 (4bis)
ISD-R                                              M                  C                                                               M                                                              C                                                       M
                                                         (2)                       (2)                                                                                                                                                                               (4)
ECASD                                X             M                     M                                                             M                                                                  M                                                  M
eUICC-Capabilities                   X              M                       M                                                          M                                                                  M                                                  M
audit trail                                                                                                                                                                                                                                                  M
signatureAlgorithm                   X              M                       M                                                          M                                                                  M                                                  M
signature                                          M (5)                 M (5)                                                        M (5)                                                              M (5)                                               M (5)
AdditionalProperty                                  O                     C(6)                                                        C(6)                                                               C(6)                                                C(6)

Table 234: EIS Usage

NOTE 1:The initial EIS comes with the information of the Profile(s) loaded and installed by the EUM during the manufacturing.

NOTE 2:The initial EIS comes with the definition of the two Security Domains ISD-R and ECASD.

NOTE 3:The EIS SHALL only contain the information of the Profiles owned by the requesting Operator

NOTE 3bis: The EIS SHALL only contain the information of the Profiles owned by an
           Operator that has authorised the requesting SM-DP to see its Profiles.

NOTE 4:The EIS SHALL contain all Security Domains definition with Key Sets that only contain mandatory values on ISD-R..

NOTE 4bis: The EIS SHALL contain all Security Domain definition of the ISD-R,
           including the description of the keysets used by the current SM-SR, without
           the key values; the KVN/Key identifiers SHALL be provided in the EIS, but
           the key values SHALL be provided as empty hexadecimal strings. This
           allows the SM-SR2 to know which keys are already present, and which
           KVN/Key identifiers are available to add new keys.

NOTE 5:The EIS is signed using the private key of the EUM (see Figure 8).

NOTE 6:The EIS SHALL contain:

    Any AdditionalProperty defined in ES1.RegisterEIS and whose name
     does not start with “gsma.ESIM.ES1”.
    Any AdditionalProperty added or updated by the SM-SR during the life
     of the eUICC.

NOTE 7:Deprecated element, it SHOULD be used only for backward compatibility to GSMA 3.1 specification. Deprecated element means that it will be removed in next specification release, so service caller or service provider SHOULD NOT rely on it.

F Key Check Values (Normative)

All key check values that have to be computed in the context of this specification SHALL follow the recommendation of GlobalPlatform Card Specification [6] section B5 and GlobalPlatform Card Specification Amendment B [8] section 3.8. Extract:

“For a DES key, the key check value is computed by encrypting 8 bytes, each with value '00', with the key to be checked and retaining the 3 highest-order bytes of the encrypted result.”

“For a AES key, the key check value is computed by encrypting 16 bytes, each with value '01', with the key to be checked and retaining the 3 highest-order bytes of the encrypted result.”

“A key check value SHALL be computed as the three most significant bytes of the SHA-1 digest of the PSK TLS Key”.

G Device Requirements (Normative)

Functional

  Dev ice
                                                            Requirement
Requirements

No.

DEV1           For connectivity the Device SHALL support:
    At least one of the network access technologies defined by 3GPP in the non-exhaustive following
     list:
o    GERAN,
o    UTRAN
o    E-UTRAN.
     UDP over IP [32] (subject to the right support of access network technology)
   TCP over IP [33] (subject to the right support of access network technology)
DEV2         For Network connection control the Device SHALL support:
   RPLMN details (LAC/TAC, NMR).
   QoS (failures, duration, power, location).
   SMS management.
   New network selection after SIM/USIM update.
DEV3         For reporting to a server the Device SHALL support:
   SMS-PP MO as defined in [3] and SMS-PP MO as defined [39] or [29] BIP as defined in DEV4
The Device SHOULD support:
        USSD
DEV4         For Profile and Platform Management the Device SHALL support:
   SMS-PP MT as defined in [3], and SMS-PP MT as defined [39] or [29]
   BIP (subject to the support of the right network access technology) as defined in [3] including
    support of commands:
o    OPEN CHANNEL (UDP and TCP over IP)
o    CLOSE CHANNEL
o    RECEIVE DATA
o    SEND DATA
o    GET CHANNEL STATUS
o    ENVELOPE (EVENT DOWNLOAD - Data available)
o    ENVELOPE (EVENT DOWNLOAD – Channel status)
DEV5         The Device SHALL contain a unique IMEI (International Mobile Equipment Identity) value compliant with
             the format defined in ETSI TS 123 003 [31].
The value of IMEI SHALL be directly copied from TERMINAL RESPONSE of the Provide Local Information
command (see ETSI TS 102 223 [3] and ETSI TS 124 008[20]).
DEV6                 The Device SHALL support, as a minimum, the following set of commands (in addition to BIP
                      commands) as defined in ETSI TS 102 223 [3] and 3GPP TS 31.111 [27]. Basic SAT commands
                      (TERMINAL PROFILE, FETCH, TERMINAL RESPONSE)
   PROVIDE LOCAL INFORMATION (location information, IMEI, NMR, date and time, access
    technology, at least)
   SEND SHORT MESSAGE
   POLL INTERVAL, POLLING OFF, TIMER MANAGEMENT [at least one timer], ENVELOPE
    (TIMER EXPIRATION)
   SET UP EVENT LIST and ENVELOPE (EVENT DOWNLOAD – location status, call connected,
    call disconnected, Access Technology Changed, Network Rejection)
   ENVELOPE (SMS-PP DOWNLOAD)
   REFRESH Command (At least mode 4 - “UICC reset”)
DEV7           The Device SHALL comply with the GSMA-EICTA document “Security Principles Related to Handset Theft”
               [30]
DEV8           The Device MAY retrieve the EID defined in section 2.2.2 of this specification from the eUICC and SHALL
               support the following commands as described in [35]:
   AT+CCHO (Open Logical Channel)
   AT+CCHC (Close Logical Channel)
   AT+CGLA (Generic UICC Logical Channel Access)
DEV9           The Device SHALL support from the [35] the following commands for all generic purposes:
   AT+CRSM (Restricted SIM access)

H Coding of the PIX for ‘Embedded UICC Remote Provisioning and Management’ (Normative)

The following coding of the PIX, following ETSI TS 101 220 [2], applies for ISD-R, ISD-P and ECASD:

    Digits 1 to 4 - Application code for ‘Embedded UICC Remote Provisioning and
     Subscription Management’
        o Coding:        Fixed value '10 10'
    Digits 5 to 8 - Not used
        o Coding:           Fixed value 'FF FF'
    Digits 9 to 14 - Application provider code
 9      10      11       12       13        14
      Industry code: ‘89’ for Telecom
Not Used: set to ‘FF FF’
    Digits 15 to 22 - Application Provider field 8 hexadecimal digits
15           16     17         18      19        20      21         22
                         Not used: set to ‘00’
‘00 00 01’ ISD-R Application. Used as the TAR
‘00 00 0D’ ISD-P Executable Load File
‘00 00 0E’ ISD-P Executable Module
‘00 00 10’ to ‘00 FF FF’ ISD-P Application. Used as
TAR. The value is allocated during the ‘Profile
Download and Installation procedure’.
‘00 00 0F’ Reserved value for the Profile’s ISD-P

‘00 00 02’ ECASD Application. Used as the TAR

I List of Identifiers (Normative)

OIDs
The following identifiers for remote provisioning are created under a dedicated OID tree under
ISO branch:
    ASN.1 notation: {iso(1) identified-organization(3) dod(6) internet(1) private(4)
        enterprise(1)}
    dot notation: 1.3.6.1.4.1
    IOD-IRI notation: /ISO/Identified-Organization/6/1/4/1
The private enterprise numbers may be found under the Internet Assigned Numbers Authority:
http://www.iana.org/assignments/enterprise-numbers/enterprise-numbers
EUM Identifier
                                               Uniqueness               Registration Entity
                            Identifier
EUM OID      within the ecosystem    ISO

1.3.6.1.4.1

SIN          within the ecosystem    ISO, according to ISO 7812-2 [19]

eUICC Identifier

                    Uniqueness                                     Registration Entity
Identifier
EID             within the ecosystem       GSMA ESIM Technical Specification
ECASD AID       within the eUICC          GSMA ESIM Technical Specification
ISD-R AID       within the eUICC          GSMA ESIM Technical Specification
ISD-P AID       within the eUICC          SM-SR within a range Defined in GSMA ESIM Technical Specification
ICCID           Global                    ITU
ISD-R TAR       within the eUICC          GSMA ESIM Technical Specification
MNO-SD AID   Within the Profile           ETSI TS 101 220 (ISD AID)
MNO-SD TAR   Within the Profile           ETSI TS 101 220 (ISD TAR)
SM-SR Identifier
                                                          Uniqueness          Registration Entity
                                 Identifier
SMSR OID                  within the ecosystem   ISO
(called SRID in [1])                             1.3.6.1.4.1
SM-DP Identifier
                                                          Uniqueness          Registration Entity
                                 Identifier
SMDP OID                  within the ecosystem   ISO
(called DPID in [1])                             1.3.6.1.4.1

Operator Identifier

Identifier              Uniqueness                            Registration Entity
                                                                         ISO
Operator OID          within the ecosystem
                                                                      1.3.6.1.4.1
MCC+MNC (IMSI)                   Global            ITU-T for MCC and National Regulators for MNC

J Verification of EID (Informative)

Verification of an EID is performed as follows:
    Using the 32 digits as a decimal integer, compute the remainder of that number on
        division by 97.
    If the remainder of the division is 1, the verification is successful; else the EID is
        invalid.

NOTE:Examples of valid EIDs are:  8900 1012 0123 4123 4012 3456 7890 1224  8900 1567 01020304 0506 0708 0910 1152  8904 4011 1122 3344 1122 3344 1122 3321

K Script Chaining implementation (Informative)

Management of Script Chaining TLVs by the SM-SR MAY be performed as described in this annex. The value and semantics of the Script Chaining TLVs are defined in ETSI TS 102 226 [5].

There are three cases where the Script Chaining implementation may be needed:

   To chain the various sub commands scripts that result from segmenting a single
    command script sent in a single ES3.sendData call, if this command script is to o big
    to fit into one transport APDU.
   To chain the two parts of the Key Establishment with Scenario#3-Mutual
    Authentication described in section 3.1.2.
   To chain two or more parts of the Download and Installation of the Profile as
    described in section 3.1.3 that have been sent in two or more ES3.sendData calls.

The last two cases can be determined by the SM-SR, by inspecting the command script passed as argument of the ES3.sendData call, and recognise if:

   it end with the “First STORE DATA command” C-APDU belonging to the
    EstablishISDPKeySet function.
   it starts with a SCP.03t TLV structure Initialize Update Command, External
    Authenticate Command or Command Data Field Encryption) belonging to the
    DownloadAndInstallation function.

In all cases, if argument moreToDo of the ES3.sendData call is false, there is no point to open a new chaining session (Script Chaining TLV with Script Chaining value of “first script –xxx”), and if one such session is already open, it can be marked to terminate after this last script (by adding a Script Chaining TLV with Script Chaining value of “subsequent script - last script”).

L Examples of PLMA Setting (Informative)

This annex presents a fictitious scenario where an Operator1 identified by its mno -id=6.7.8.9 successively calls one of the SetPLMA operations, and illustrates how this affects the authorisations for the specified M2M SP identified by an OID=1.2.3.4.

The table reads with time ascending from top to bottom.

Time         mno-   m2m- profile            authorised                    Consequences
              id    sp-id Type              Operations
    t0   -             -      -         -                      No PLMA set: M2M SP is not authorised for
                                                               any operation or any notifications on
                                                               Profiles of Operator1.
    t1   6.7.8.9    1.2.3.4   ABC       Enable,                1.2.3.4 is authorised to enable Profiles of
                                        HandleProfileDow nlo   type ABC of Operator1 and is authorised to
                                        adedNotification       receive notifications w hen a Profile of type
                                                               ABC of Operator1 is dow nloaded
    t2   6.7.8.9    1.2.3.4   ABC       Enable, Disable        1.2.3.4 is authorised to enable and disable
                                                               Profiles of type ABC of Operator1 but is not
                                                               authorised     any     more     to    receive
                                                               notifications w hen a Profile of type ABC of
                                                               Operator1 is dow nloaded
    t3   6.7.8.9    1.2.3.4   Empty   Enable                   1.2.3.4 is authorised to enable Profiles of
                              and                              Operator1 w ithout a Profile Type in EIS.
                              Missing
                              are                              1.2.3.4 is still authorised to enable and
                              treated                          disable Profiles of type ABC of Operator1
                              as the
                              same
    t4   6.7.8.9    1.2.3.4   Empty                            1.2.3.4 is not authorised for any operation
                              and                              on Profiles of Operator1 w ithout a Profile
                              Missing                          type in EIS
                              are
                              treated                          1.2.3.4 is still authorised to enable and
                              as the                           disable Profiles of type ABC of Operator1
                              same
    t5   6.7.8.9    1.2.3.4   ABC       Enable                 1.2.3.4 is authorised to enable profiles of
                                                               type ABC of Operator1
    t6   6.7.8.9    1.2.3.4   ABC                              1.2.3.4 is not authorised for any operation
                                                               for Profile type ABC of Operator1

M Examples of ONC Setting (Informative)

This annex presents a fictitious scenario where an Operator 1 identified by its mno-id=6.7.8.9 successively calls one of the SetONC operations, and illustrates how this affects the notifications for the Operator.

The table reads with time ascending from top to bottom.

Time mno-id profile            discarded                             Consequences
             Type             Notifications
 t0    -         -        -                      No ONC set: Operator1 receives all notifications for all
                                                 ow ned Profiles.
 t1    6.7.8.9   ABC      HandleProfileEnable    Operator1 receives “no“ Enable notifications for ow ned
                          dNotification          Profiles of type ABC.
                                                 Operator1 receives for ow ned Profiles w ith a Profile type in
                                                 EIS (apart from ABC) “all” notifications.
                                                 Operator1 receives for ow ned Profiles w ithout a Profile type
                                                 in EIS “all” notifications.
 t2    6.7.8.9   ABC      HandleProfileEnable    Operator1 receives “no“ Enable and “no”               Disable
                          dNotification,         notifications for ow ned Profiles of type ABC.
                          HandleProfileDisable
                                                 Operator1 receives for ow ned Profiles w ith a Profile type in
                          dNotification
                                                 EIS (apart from ABC) “all” notifications.
                                                 Operator1 receives for ow ned Profiles w ithout a Profile type
                                                 in EIS “all” notifications.
 t3    6.7.8.9   Empty   HandleProfileEnable     Operator1 receives “no“ Enable and “no”               Disable
                 and     dNotification           notifications for ow ned Profiles of type ABC.
                 Missing
                                                 Operator1 receives for ow ned Profiles w ith a Profile type in
                 are
                 treated                         EIS (apart from ABC) “all” notifications.
                 as the                          Operator1 receives “no“ Enable notifications for ow ned
                 same                            Profiles w ithout a Profile type in EIS.
 t4    6.7.8.9   Empty   Empty and Missing Operator1 receives “no“ Enable and “no” Disable
                 and     are treated as the notifications for ow ned Profiles of type ABC.
                 Missing same
                                            Operator1 receives for ow ned Profiles w ith a Profile type in
                 are
                 treated                    EIS (apart from ABC) “all” notifications.
                 as the                     Operator1 receives for ow ned Profiles w ithout a Profile type
                 same                       in EIS “all” notifications.

Table O1: Example of Applying ONC

N Document Management (Informative)

N.1 Document History

Version Date          Brief Description of Change                Approval      Editor /
                                                                 Authority     Company
                                                                 GSMA
                                                                 Embedded
                                                                 SIM
          19/12/201   1st Release of Document, submitted to                    Ian Smith,
V1.0                                                             Leadership
          3           PSMC#119 for approval                                    GSMA
                                                                 Team and
                                                                 PSMC
                                                                 GSMA
                                                                 Embedded
                                                                 SIM           Alexis Michel,
          16/09/201
V2.0                  2nd Release of Document                    Leadership    Oberthur
          4
                                                                 Team and      Technologies
                                                                 PSMC
                                                                 GSMA
                                                                 Embedded
                                                                 SIM           Alexis Michel,
          29/05/201    nd
V3.0                  3 Release of Document                      Leadership    Oberthur
          5
                                                                 Team and      Technologies
                                                                 PSMC
                                                                 GSMA
                                                                 Embedded
                                                                 SIM           Alexis Michel,
V3.1      12/05/16    Minor Release of Documents                 Leadership    Oberthur
                                                                 Team and      Technologies
                                                                 PSMC
                                                                 GSMA
                                                                 Embedded
                                                                 SIM           Jérôme
V3.2      20/06/17    Minor Release of Document                  Leadership    Duprez,
                                                                 Team and      Gemalto
                                                                 PSMC
                                                                 GSMA
                                                                 Embedded
                                                                 SIM           Yolanda Sanz
V4.0      25/02/19    Major release of Document                  Leadership    / GSMA
                                                                 Team and
                                                                 TG
Version Date            Brief Description of Change                 Approval      Editor /
                                                                    Authority     Company
                                                                                  Jérôme
V4.1       05/06/20     Minor release of document                   ISAG          Duprez,
                                                                                  Thales

N.2 Other Information

Type                              Description
Document Owner                    Yolanda Sanz, GSMA
Editor / Company                  Jérôme Duprez, Thales

It is our intention to provide a quality product for your use. If you find any errors or omissions, please contact us with your comments. You may notify us at [email protected]

Your comments or suggestions & questions are always welcome.

© GSM Association. Converted automatically from the published PDF; layout, figures and tables may differ from the original. The authoritative version is the original: https://www.gsma.com/esim/wp-content/uploads/2020/06/SGP.02-v4.1.pdf.