Description
A Hybrid AAS BS is an Active Antenna System base station that has both a conducted RF interface and a radiated RF interface in the far field, and that conforms to a hybrid requirements set. The definition appears in the RF and EMC specification family 37.105, 37.114, 37.145, 37.843, 37.941 and 38.817. It is a conformance category rather than a distinct radio architecture: the base station is an AAS (an antenna array with integrated transceivers), but it is built and declared in such a way that some requirements can be verified at a conducted port while others must be verified over the air.
The need for this category arises from the evolution of base station RF testing. Traditional base stations have a conducted RF connector, so transmitter and receiver characteristics (output power, EVM, ACLR, spurious emissions, blocking, etc.) can be measured directly at the port with a test instrument. AAS base stations integrate the radio and the antenna array, so in the general case there is no accessible conducted port and all RF requirements must be verified as radiated requirements in the far field (OTA). OTA testing is more complex, more expensive, and less repeatable than conducted testing, and some parameters are difficult to measure purely radiated.
A hybrid AAS BS provides a middle path. It exposes a conducted interface (for example, at the transceiver array boundary or at a defined internal test point) in addition to the radiated interface. This allows a subset of requirements to be demonstrated by conducted measurement, while the radiated requirements that depend on the antenna array behaviour (such as radiated power, OTA sensitivity, and radiated emissions) are demonstrated in the far field. The applicable requirements are partitioned into a hybrid requirements set, and the base station declares which requirements are met conducted and which are met radiated.
The specifications define the reference points and the conditions under which each interface is used. 37.105 covers the conducted and radiated RF requirements for AAS base stations, including the definitions of conducted and radiated interfaces and the hybrid requirement set. 37.114 addresses electromagnetic compatibility and radio spectrum matters for AAS, 37.145 covers the corresponding conformance testing, and 37.843, 37.941 and 38.817 provide additional RF and test methodology material. Together these documents ensure that a hybrid AAS BS can be tested consistently and that its declared performance is comparable to that of a fully conducted or fully radiated base station.
In deployment terms, hybrid AAS base stations are typically used where the operator or vendor wants the performance benefits of massive MIMO (beamforming, spatial multiplexing, high capacity) while retaining some of the testability and diagnosability of a conducted architecture. The conducted interface can also be used for production testing and field diagnostics. The category is important for regulatory and type-approval processes, because it determines which test methods apply and how the base station's RF performance is demonstrated to authorities.
The definition has remained identical from Rel-15 through Rel-19. This stability reflects the maturity of the AAS RF requirement framework: the hybrid category was established early and has not needed semantic revision, even as the underlying requirement values and test methods have been refined in the specifications.
Purpose & Motivation
The shift from traditional base stations to Active Antenna Systems created a testing problem. When the radio and antenna are integrated, there is no conducted port at which to measure RF characteristics, so the industry moved toward over-the-air testing. OTA testing, however, is expensive, requires large anechoic chambers or compact antenna test ranges, and is subject to measurement uncertainty that conducted testing does not have. For many parameters, conducted measurement remains more accurate and more repeatable.
Hybrid AAS BS exists to reconcile these two worlds. By allowing a base station to expose both a conducted and a radiated interface, it lets vendors and operators demonstrate compliance using the most appropriate method for each requirement. Requirements that are fundamentally about the radiated behaviour of the array are tested OTA; requirements that can be measured at a defined conducted reference point are tested there. This reduces test cost and improves confidence in the declared performance.
The category also supports regulatory harmonisation. Different regions have different approaches to AAS conformance, and a standardised hybrid requirements set gives a common basis for type approval. It was introduced in Rel-15 alongside the broader AAS RF requirement work in the 37.105 family, and it has provided a stable framework that subsequent releases have built upon without redefining the core concept.
What changed in its specifications
The latest release-to-release comparison of specifications that define Hybrid AAS BS. Each summary describes the whole specification, not only this term.
Extended OTA BS testing to 43.5–48.2 GHz; added new measurement/uncertainty clauses; revised procedures.
Full comparison in TR 37.941 →Release Timeline
Detected Changes Across Releases
from 3GPP Change RequestsSpecific changes extracted from the „Change history“ tables of 3GPP specifications (1 CRs across 1 releases). Complements the general historical overview above with the evidence-based evolution of this function.
Defining Specifications
3GPP specifications that define or reference Hybrid AAS BS, with the latest known release. Sourced from the 3GPP document catalog — see methodology.
| Specification | Title | Release |
|---|---|---|
| TS 37.105 vj40 | AAS Base Station Radio Requirements | Rel-19 read |
| TS 37.114 vj00 | EMC for Active Antenna System Base Stations | Rel-19 read |
| TS 37.145 vj40 | AAS Base Station Radiated Requirements | Rel-19 read |
| TR 37.843 vf70 | AAS BS Radiated RF Requirement Background | Rel-15 read |
| TR 37.941 vj20 | RF Conformance Testing Background for Radiated BS Requirements | Rel-19 read |
| TS 38.817 | 3GPP TR 38.817 | Rel-15 read |