Menu
Latest
12 meetings · Prague, Jeju · 12–16 Oct
Reports
RAN1#126-bis · SA2#177

Glossary term · Interface

E-UTRA-PC5

E-UTRA PC5 Reference Point

Interface →

E-UTRA-PC5 is a PC5 sidelink reference point implemented over E-UTRA (LTE), corresponding to LTE PC5 in TS 23.287, that enables direct device-to-device communication for V2X and proximity services without traversing the network.

Introduced
Rel-16
Where
Services
Specifications
2 specs
E-UTRA-PC5 Description Purpose What changed Neighbours Specifications

Description

E-UTRA-PC5 is the PC5 reference point realized over the E-UTRA radio interface, as specified in the proximity-based services and V2X architecture documents TS 24.577 and TS 24.587. The PC5 reference point is the interface between two UEs that communicate directly, without user-plane traffic passing through the core network. When implemented over E-UTRA, it uses the LTE sidelink physical and protocol layers (PSCCH, PSSCH, PSDCH, and the sidelink MAC/RLC/PDCP), and it is the radio bearer used for LTE V2X (LTE-V) and public safety direct communication.

In the 3GPP architecture, PC5 is defined as a reference point in TS 23.287 (for V2X) and TS 23.303 (for ProSe). The term E-UTRA-PC5 is used in the protocol specification TS 24.577 (V2X application layer) and TS 24.587 (V2X UE-to-UE relay) to distinguish the LTE-based PC5 from the NR-based PC5 (NR-PC5). The definition explicitly states that E-UTRA-PC5 corresponds to the term LTE PC5 used in TS 23.287, establishing terminology equivalence between the architecture and protocol specifications.

E-UTRA-PC5 supports both unicast and groupcast/broadcast communication. In LTE V2X, the sidelink supports broadcast (mode 3 and mode 4) and, from Rel-14 onwards, groupcast and unicast via higher-layer identifiers. Resource allocation can be network-scheduled (mode 3, where the eNB allocates sidelink resources via RRC) or UE-autonomous (mode 4, where the UE selects resources from a configured pool using sensing and semi-persistent scheduling). The PC5 interface carries V2X messages such as CAM, DENM, and BSM, as well as IP and non-IP traffic.

At the protocol level, E-UTRA-PC5 uses the PC5 signalling protocol (PC5-S) for direct link setup, and the V2X application layer protocols defined in TS 24.577 for message formats. Security for PC5 is provided by the PC5 security procedures, with credentials provisioned by the network. The UE-to-UE relay function specified in TS 24.587 allows a remote UE to reach the network via a relay UE over E-UTRA-PC5, extending coverage for out-of-coverage or cell-edge devices.

The distinction between E-UTRA-PC5 and NR-PC5 matters because the two use different radio interfaces and resource allocation frameworks, and a UE may support one or both. In Rel-18, the definition's reference to TS 23.287 was temporarily changed to TS 23.256, reflecting the introduction of the ProSe architecture document in that release; in Rel-19 it reverted to TS 23.287. This shows how the term's normative anchor evolved as the architecture specifications were reorganized.

Purpose & Motivation

E-UTRA-PC5 exists to provide direct device-to-device communication over LTE for safety-critical and proximity services where routing traffic through the network would add latency, consume backhaul, or fail entirely when coverage is unavailable. Public safety users need to communicate when infrastructure is damaged, and V2X use cases such as collision avoidance require end-to-end latency of tens of milliseconds that a network round trip cannot reliably guarantee.

As V2X requirements emerged in Rel-14, the PC5 interface was enhanced to support higher speeds, higher density, and V2X-specific message sets. The term E-UTRA-PC5 was introduced in Rel-16 to disambiguate the LTE-based PC5 from the NR-based PC5 being developed for 5G V2X, since both can coexist and a UE may use either depending on coverage and capability.

The naming equivalence with LTE PC5 in TS 23.287 ensures that architecture specifications and protocol specifications refer to the same interface, avoiding confusion as the V2X architecture was split across multiple documents. The relay function in TS 24.587 further extends the purpose of E-UTRA-PC5 to coverage extension, allowing remote UEs to reach the network through a relay UE.

What changed in its specifications

The latest release-to-release comparison of specifications that define E-UTRA-PC5. Each summary describes the whole specification, not only this term.

TS 24.587Rel-18 → Rel-19

Rel-19 adds relay-related indicator fields to Requested UE policies IE and clarifies PC5 unicast link security message protection.

Full comparison in TS 24.587 →

Release Timeline

Evolution Across Releases

An overview written from the defining specifications, not a verified change history. For the exact text, open the specifications listed below.

Rel-16 Initial

Initial definition introduced to distinguish LTE-based PC5 from NR-based PC5. The term is defined as the PC5 reference point over E-UTRA and equated with the term LTE PC5 in TS 23.287.

Definition carried over unchanged from Rel-16.

The normative reference was changed from TS 23.287 to TS 23.256, reflecting the introduction of the ProSe architecture specification in Rel-18; the technical meaning of the term was unchanged.

The normative reference reverted to TS 23.287, restoring the original anchor to the V2X architecture specification.

Defining Specifications

3GPP specifications that define or reference E-UTRA-PC5, with the latest known release. Sourced from the 3GPP document catalog — see methodology.

SpecificationTitleRelease
TS 24.577 vj30 A2X Services in 5G System Rel-19 read
TS 24.587 vj30 V2X Services Protocols for 5G System Rel-19 read