Menu
Latest
12 meetings · Prague, Jeju · 12–16 Oct
Reports
RAN1#126-bis · SA2#177

Glossary term · Radio Access Network

Configured Uplink Frequency

Configured Uplink Frequency

Radio Access Network →

Configured Uplink Frequency is the uplink frequency for a UE once higher layers have supplied all information needed to transmit on it, distinguishing usable frequencies from those merely known or measured.

Introduced
Rel-9
Where
Radio Access Network › UTRAN (3G)
Specifications
5 specs
Configured Uplink Frequency Description Purpose What changed Neighbours Specifications

Description

The Configured Uplink Frequency is a UE-specific concept used in the UMTS terrestrial radio access (UTRA) specifications to define when an uplink frequency is usable for transmission by a given terminal. A frequency is not considered configured simply because it exists in the network's spectrum plan or because the UE can measure it; it becomes configured only when the UE has received, via higher-layer signalling (typically RRC), the complete set of parameters required to perform uplink transmission on that frequency. These parameters include scrambling code information, power control configuration, timing and synchronization references, and the physical channel configuration needed to map transport channels onto the uplink physical channels.

The concept matters because UMTS supports multi-carrier uplink operation, notably Dual-Cell HSUPA (DC-HSUPA) and later multi-carrier enhancements. In such deployments a UE may be aware of, or able to measure, several uplink carriers, but only a subset are actually configured for transmission at any moment. Higher layers—principally RRC in TS 25.331, with MAC and physical-layer behaviour described in TS 25.321, 25.213 and 25.214—control which frequencies are configured, and the physical layer then applies the appropriate transmission procedures only on those frequencies. The definition is referenced in TS 25.302 (services provided by the physical layer) and TS 25.319 (enhanced uplink), which rely on a precise notion of when a frequency is available for transmission.

Operationally, the configured uplink frequency set determines where the UE may transmit E-DCH and associated control channels. When the network adds a secondary uplink frequency, it sends the relevant configuration via RRC signalling; once complete, that frequency becomes configured and the UE can begin transmission subject to activation and scheduling decisions by the NodeB. Conversely, when the network releases the configuration, the frequency ceases to be configured and the UE must stop transmitting on it. This separation between 'configured' and 'active' is important: configuration establishes the capability and parameters, while MAC-level scheduling and activation govern actual use.

The term also underpins measurement and mobility behaviour. The UE reports measurements on frequencies according to what is configured, and the network uses these reports to decide whether to add, modify or remove carriers. Because the definition is anchored to 'all relevant information from higher layers', it provides an unambiguous, testable criterion that both UE implementations and conformance test specifications can rely on, avoiding ambiguity about when a UE is permitted to transmit.

Across releases from Rel-9 through Rel-19 the definition has remained textually identical, reflecting the stability of the underlying multi-carrier uplink framework in UMTS. Even as later releases added features such as improved uplink transmit diversity and further multi-carrier combinations, the fundamental notion of a configured uplink frequency—complete higher-layer configuration as the gate for transmission—has been retained without revision.

Purpose & Motivation

The concept exists to give a precise, UE-specific answer to the question: on which uplink frequencies may this terminal transmit? In multi-carrier UMTS, a UE can be aware of many frequencies through measurement configuration or system information, but transmitting on a frequency requires a full set of parameters—scrambling codes, power control, timing, and physical channel configuration. Without a formal definition, implementations and test houses could disagree about when transmission is permitted, leading to interoperability problems and ambiguous conformance requirements.

By defining a frequency as configured only when all relevant higher-layer information has been received, 3GPP created a clean boundary between the RRC configuration domain and the MAC/physical-layer transmission domain. This supports the activation and deactivation model used in DC-HSUPA and multi-carrier HSUPA, where carriers can be configured but not immediately used, and allows the network to prepare a secondary uplink carrier before scheduling traffic on it.

The definition also supports measurement control and mobility: the network can distinguish frequencies the UE is merely monitoring from those it is equipped to use, simplifying handover and carrier management decisions. Its unchanged persistence from Rel-9 to Rel-19 demonstrates that the original formulation solved the problem robustly.

What changed in its specifications

The latest release-to-release comparison of specifications that define Configured Uplink Frequency. Each summary describes the whole specification, not only this term.

TS 25.213Rel-11 → Rel-12

Rel-12 adds a new uplink physical channel DPCCH2 for DCH enhancements, including its spreading, code allocation, and effects on HS-DPCCH gain settings.

Full comparison in TS 25.213 →
TS 25.214Rel-18 → Rel-19

Rel-19 brings only minor changes to TS 25.214: 0 clauses changed, with no change attributed to a release feature.

Full comparison in TS 25.214 →

Release Timeline

Evolution Across Releases

An overview written from the defining specifications, not a verified change history. For the exact text, open the specifications listed below.

Rel-9 Initial

Initial definition introduced: for a specific UE, an uplink frequency is configured if the UE has received all relevant information from higher layers in order to perform transmission on that frequency. This established the UE-specific, configuration-based gate for uplink transmission in multi-carrier UMTS.

Definition text carried over unchanged from Rel-9.

Definition text carried over unchanged from Rel-9.

Definition text carried over unchanged from Rel-9.

Definition text carried over unchanged from Rel-9.

Definition text carried over unchanged from Rel-9.

Definition text carried over unchanged from Rel-9.

Definition text carried over unchanged from Rel-9.

Definition text carried over unchanged from Rel-9.

Definition text carried over unchanged from Rel-9.

Definition text carried over unchanged from Rel-9.

Defining Specifications

3GPP specifications that define or reference Configured Uplink Frequency, with the latest known release. Sourced from the 3GPP document catalog — see methodology.

SpecificationTitleRelease
TS 25.213 vj00 UTRA FDD Spreading and Modulation Rel-19 read
TS 25.214 vj00 UTRA FDD Physical Layer Procedures Rel-19 read
TS 25.302 vj00 UTRA Physical Layer Services Rel-19 read
TS 25.319 vj00 Enhanced Uplink for UTRA FDD/TDD Rel-19 read
TS 25.321 vj00 MAC Protocol Specification for UTRAN Rel-19 read