Menu
Latest
12 meetings · Prague, Jeju · 12–16 Oct
Reports
RAN1#126-bis · SA2#177

Glossary term · Physical Layer

Composite spectrum emission mask

Composite spectrum emission mask

Physical Layer →

Composite spectrum emission mask is an emission mask requirement for intraband non-contiguous carrier aggregation, formed by combining individual sub-block spectrum emission masks to keep UE transmitter emissions within regulatory and coexistence limits across multiple separated carriers.

Introduced
Rel-12
Where
User Equipment
Specifications
2 specs
Composite spectrum emission mask Description Purpose What changed Neighbours Specifications

Description

The Composite Spectrum Emission Mask (Composite SEM) is a radio frequency (RF) transmitter requirement defined in 3GPP TS 36.101 for LTE user equipment (UE) and referenced in TS 36.833 for the corresponding conformance test methodology. It applies specifically to intraband non-contiguous carrier aggregation (CA), where a UE transmits on two or more component carriers within the same operating band but with gaps between them. In such a configuration, the aggregated transmission does not form a single contiguous block of spectrum; instead it consists of several sub-blocks separated by unused spectrum. The composite SEM is the overall emission mask that results from combining the individual spectrum emission masks defined for each sub-block.

Architecturally, the requirement is built from the bottom up. Each sub-block — typically corresponding to one component carrier or a contiguous group of carriers — has its own spectrum emission mask that defines the maximum permitted out-of-band emissions as a function of frequency offset from the sub-block's edges. The composite mask is then constructed by taking, at each frequency point, the combination of the applicable sub-block masks, effectively producing an envelope that bounds the total emitted power across the entire aggregated bandwidth, including the inter-sub-block gaps. This ensures that emissions in the gaps between carriers, as well as outside the outermost carrier edges, remain controlled.

The composite SEM matters because non-contiguous CA creates emission scenarios that a single contiguous mask cannot describe. Intermodulation products and spectral regrowth from multiple simultaneously active transmitters can fall into the gaps between sub-blocks or into adjacent operators' spectrum. By defining a composite envelope, the standard gives both UE vendors and test laboratories a deterministic pass/fail criterion. The UE must demonstrate that its actual transmitted spectrum, measured across the relevant frequency range, stays below the composite mask at every point.

In terms of network role, the composite SEM is part of the broader set of RF conformance requirements that guarantee a UE can coexist with other UEs, with other systems in adjacent bands, and with regulatory emission limits. It is verified through transmitter tests in TS 36.833, where the test setup configures the UE for the relevant non-contiguous CA combination and measures the emitted spectrum. Because the requirement is defined per band and per CA combination, the standard contains extensive tables of applicable configurations.

The concept has remained stable across releases from Rel-12 through Rel-20. Its definition text is unchanged, reflecting that the underlying physical principle — bounding aggregate emissions of separated sub-blocks — does not change even as new bands and CA combinations are added. New band entries and CA configurations are introduced in each release, but the definitional concept of the composite SEM persists as a foundational RF requirement for LTE-Advanced carrier aggregation.

Purpose & Motivation

The Composite SEM exists to solve a specific problem created by intraband non-contiguous carrier aggregation: when a UE transmits on multiple separated sub-blocks within one band, the resulting emission profile cannot be adequately described by a single contiguous spectrum emission mask. Before non-contiguous CA was introduced, emission requirements were defined for a single carrier or a contiguous aggregation, where the transmitted signal occupied one continuous block of spectrum. With non-contiguous aggregation, gaps appear between sub-blocks, and emissions can arise both within those gaps and outside the aggregate. A new framework was needed to bound total emissions across this fragmented spectrum.

The composite approach was chosen because it is modular and scalable. Rather than defining a bespoke mask for every possible non-contiguous CA combination, the standard combines the individual sub-block masks into a composite envelope. This lets the requirement be derived systematically from well-understood single-block masks, while still providing a rigorous bound on the aggregate emission. It also accommodates the many possible arrangements of component carriers and gap sizes without requiring an unmanageable number of unique definitions.

For regulators and operators, the composite SEM provides assurance that LTE-Advanced UEs using non-contiguous CA will not cause harmful interference to adjacent spectrum, whether that spectrum belongs to the same operator, another operator, or another radio system. For UE vendors, it provides a clear design target for the transmitter's linearity and filtering. The requirement has been carried forward essentially unchanged from Rel-12 to Rel-20, demonstrating that the original formulation was robust enough to support the continued expansion of LTE carrier aggregation.

What changed in its specifications

The latest release-to-release comparison of specifications that define Composite spectrum emission mask. Each summary describes the whole specification, not only this term.

TS 36.101Rel-12 → Rel-13

Rel-13 added carrier aggregation requirements, 4Rx antenna port tests, MTC coverage enhancements, LAA test parameters, FD-MIMO procedures, and downlink interference mitigation requirements.

Full comparison in TS 36.101 →

Release Timeline

Evolution Across Releases

An overview written from the defining specifications, not a verified change history. For the exact text, open the specifications listed below.

Rel-12 Initial

Initial introduction of the composite spectrum emission mask concept for intraband non-contiguous carrier aggregation, defining the requirement as a combination of individual sub-block spectrum emission masks.

Definition carried over unchanged; new band and CA combinations may have been added but the concept remained identical.

Definition carried over unchanged from previous releases.

Definition carried over unchanged; the composite SEM concept remained stable.

Definition carried over unchanged.

Definition carried over unchanged.

Definition carried over unchanged.

Defining Specifications

3GPP specifications that define or reference Composite spectrum emission mask, with the latest known release. Sourced from the 3GPP document catalog — see methodology.

SpecificationTitleRelease
TS 36.101 vk10 E-UTRA UE RF Requirements Rel-20 read
TS 36.833 3GPP TR 36.833 Rel-12 read