Description
Blind Transmission is a mechanism used in 3GPP networks to reduce the interruption time during PS (Packet Switched) handover. It refers to the decision made by the SGSN (Serving GPRS Support Node) or the target BSS (Base Station Subsystem) / GANC (Generic Access Network Controller) to start the transmission of downlink N-PDUs (Network Protocol Data Units) or LLC PDUs (Logical Link Control PDUs) for a given mobile station before receiving confirmation that the PS handover procedure has been successfully completed. This is defined in 3GPP specifications 43.129 and 44.318.
In a typical PS handover, the source BSS initiates the handover by sending a Handover Required message to the SGSN. The SGSN then selects a target BSS and sends a Handover Request. The target BSS allocates resources and responds with a Handover Request Acknowledge. The SGSN then sends a Handover Command to the mobile station via the source BSS, and the mobile station accesses the target BSS. After the mobile station successfully accesses the target BSS, the target BSS sends a Handover Complete message to the SGSN, and the SGSN sends a Handover Complete Acknowledge to the target BSS. Only after this confirmation does the SGSN start forwarding downlink data to the target BSS. This process introduces latency, which can degrade user experience for delay-sensitive applications.
Blind Transmission optimizes this process by allowing the SGSN or the target BSS/GANC to begin transmitting downlink data to the mobile station as soon as the target BSS has allocated resources and is ready to receive, without waiting for the Handover Complete confirmation. This means that downlink data may be sent to the target BSS before the mobile station has fully completed the handover, potentially reducing the handover interruption time. The data is buffered at the target BSS until the mobile station is ready to receive it.
The decision to use Blind Transmission is made by the SGSN or the target BSS/GANC based on factors such as the expected handover success probability, the availability of resources, and the QoS requirements of the session. It is particularly beneficial for real-time services like VoLTE or conversational video, where minimizing latency is critical. However, it introduces a risk of data loss if the handover fails, as the data may be sent to a target BSS that the mobile station never successfully accesses. Therefore, it is typically used when the handover success is highly likely.
Blind Transmission is supported in both GERAN (GSM/EDGE Radio Access Network) and GAN (Generic Access Network) environments. In GERAN, it is specified in 43.129 for PS handover between BSSs. In GAN, it is specified in 44.318 for handover between GANC and BSS. The feature has been available since Release 8 and has been carried forward through subsequent releases without changes to its definition.
Purpose & Motivation
Blind Transmission was introduced to address the latency inherent in the standard PS handover procedure. In traditional handover, downlink data transmission is suspended until the handover is confirmed complete, which can cause significant interruption for delay-sensitive applications. This is particularly problematic for real-time services such as voice over IP (VoLTE) and video calls, where even a few hundred milliseconds of interruption can be noticeable. Blind Transmission reduces this interruption by allowing the network to start sending downlink data to the target cell before the handover is fully confirmed, thereby improving the user experience.
The feature was motivated by the need to support seamless mobility for packet-switched services in GSM/EDGE and GAN networks. As mobile networks evolved to support more data-intensive applications, the limitations of the traditional handover procedure became more apparent. Blind Transmission provides a simple yet effective way to reduce handover latency without requiring complex changes to the core network or the mobile station. It leverages the fact that the target BSS can buffer data until the mobile station arrives, and if the handover fails, the data can be discarded or retransmitted.
Despite its benefits, Blind Transmission is not without risks. If the handover fails, the data sent to the target BSS may be lost, leading to packet loss and potential retransmissions at higher layers. Therefore, it is typically used in scenarios where the handover success probability is high, such as when the radio conditions are favorable or when the target cell is known to be reliable. The feature has been standardized since Release 8 and remains a valuable tool for optimizing handover performance in 2G and GAN networks.
What changed in its specifications
The latest release-to-release comparison of specifications that define Blind Transmission. Each summary describes the whole specification, not only this term.
Added CSG and Hybrid cell support to PS handover procedures in GERAN A/Gb to UTRAN/GERAN Iu mode.
Full comparison in TS 43.129 →PS Handover between GERAN/UTRAN mode and GAN Mode, with new IEs and causes.
Full comparison in TS 44.318 →Release Timeline
Evolution Across Releases
An overview written from the defining specifications, not a verified change history. For the exact text, open the specifications listed below.
Defining Specifications
3GPP specifications that define or reference Blind Transmission, with the latest known release. Sourced from the 3GPP document catalog — see methodology.
| Specification | Title | Release |
|---|---|---|
| TS 43.129 vj00 | PS Handover in GERAN A/Gb and GAN Modes | Rel-19 read |
| TS 44.318 vj00 | Generic Access Network (GAN) Interface Procedures | Rel-19 read |